Search Documents

By Zhuang Jianming, Liu Qinxia, Yuan Mingliang, Mei Xiangong, Chen Jin

Up to now, the leaching of manganese carbonate ore is usually performed at high temperature of 363K and the leaching rate is lower than 90%. Although in laboratory test, the leaching rate is only 90%. This paper introduced an improved method for leaching of manganese carbonate ore. Certain ammonium salt was added to the pulp to raise the solubility of Mn2+ and reduce the adsorption quantity of Mn2+ on the ore surface. Experimental results show that a leaching rate over 95% can be obtained at the temperature >273K. The activation energy is calculated to be 7.15 KJ/mol and is lower than that of normal leaching technique. The effects of the parameters, such as particle size, pulp density and initial acid concentration on the process results are investigated. A leaching rate higher than 95% can be obtained under the following conditions: particle size below 0.25mm, leaching time 60 min, stirring speed higher than 960 r.pm. H2SO4:MnCO3>1 .2, pulp density 105-205 g.L-l. A kinetic model was deduced, verifying with actual experiments. It showed that the model can describe the leaching process successfully.

Jan 1, 1995

By Nolan B. Aughenbaugh

Zoning and environmental restrictions on land usage now make open- pit quarrying more and more difficult, especially near urban areas. One option for quarry operators is to go underground for mineral production. While underground-mining costs are higher than those for open-cut work, there are several compensating advantages. In many cases it is possible to produce the same material underground without affecting land values, and the surface is preserved for industrial, residential, or agricultural purposes. Proper planning can yield underground sites which have great potential value for industrial plants, warehouses, or other business uses. It is essential to plan underground mineral extraction using a three-dimensional modular-room architectural concept to fully exploit secondary space utilization. Prior to the start of underground mining an operator must make a careful geological engineering study to deter- mine the suitability of the deposit and must prepare a plan for safe and economical mining for the purpose of converting to secondary usage.

Jan 1, 1974

By D. J. Shields

This paper describes a dynamic short-nun mineral supply model that incorporates secondary processing, transportation, mineral market structure, and direct mining and milling costs. The method employed is network flow programming. Empirical tests utilizing domestic phosphate industry data have been conducted by the Bureau of Mines, U.S. Department of the Interior. In the model, nodes represent physical locations such as a mine or port. Arcs represent either a process, such as mining, or movement, such as rail or barge transport. Each arc is described by lower or minims allowable flow bounds, upper or maximum possible flow bands, and variable cost. Mines and previous period inventories represent potential supply. The model is optimized via a cost minimizing algorithm, which attempts to fulfill stated total demand at the minimum possible system cost given the arc constraints. An optimal solution of the model will predict production patterns by mineral property for each prespecified level of demand. A mineral property is defined as a separate accounting entity such as a mine. The results of serial optimizations are used to construct the short-run supply curve. Dynamic policy analysis can be conducted by altering the arc constraints.

Jan 1, 1986

By J de Cuyper, E. J. Parkins, H. L. Shergold, W. Freyberger

The paper is divided into two parts. The first part describes an investigation of the effect of temperature on the conditioning and flotation of an ilmenite ore with a 1:l oleic acid-fuel oil mixture as collector. During conditioning the pulp underwent characteristic changes of flocculation, deflocculation and dispersion which were monitored by measuring the power consumption of the conditioner motor. Optimum flotation results were obtained at the end of the deflocculation period. High ilmenite recoveries were obtained at high temperatures and high concentrate grades at low temperatures. The second part of the paper describes a study of the effect of temperature on the adsorption of oleic acid at the ilmenite/water interface. At high adsorption densities it was chemical and exothermic. Contact angles showed that the hydrophobicity of the collector-coated minerals increased with an increase in temperature.

Jan 1, 1976

By W. Morgan, D. Gove

In truck and shovel operations, productivity and cost per ton are influenced by the system matching choice, Optimization involves a balance of the size and number of trucks, the size and type of loading tool and the projected material conditions and haul roads. Caterpillar has updated its Fleet Production and Cost program so miners can more easily look at matching choices and optimize on the variable they choose. This paper introduces the Fleet Production and Cost program. It then demonstrates its capabilities with examples of optimization. Mining operations that use trucks need to properly match the number and size of hauling units (trucks, wagons, scrapers, etc.) to a loading unit (wheel-loader, hydraulic shovel-excavator, cable shovel, push tractor, etc.) to provide the best possible fleet match. Optimizing fleet match minimizes the cost per unit of material moved by that fleet. As haul conditions change (haul length, grade or rolling resistance), there may be need to adjust the number of trucks to maintain the optimum fleet match. Fleet Production and Cost is a tool that can be used to optimize the truck-loader match.

Jan 1, 1995

By Charles P. Lazzara, Alex C. Smith, Mark W. Ryan

The U.S. Bureau of Mines developed an experimental method to evaluate the relative effectiveness of water additives on the extinguishment of coal fires. The experiments were conducted in the fire zone of the multiple entry section of the Bruceton Experimental Mine. Chambers filled with one hundred and eighty kilograms of Pittsburgh seam coal were ignited and allowed to burn until well developed fires were achieved. Extinguishing agent-water solutions were then applied to the fires and the quantity required to extinguish the fires compared to the amount of water alone required to extinguish similar fires. A 20% diammonium phosphate-water solution required an average of 22 L to extinguish the coal fires, while two commercially available additive-water solutions required an average of 30.6 and 30.3 L, respectively. The average amount of water required to extinguish the fires was 28 L. An analysis of covariance, using the thermal energy of the coalbed, Q, to quantify the fire at the time of extinguishment, showed that the diammonium phosphate-water solution was slightly more effective at extinguishing these coal fires than water alone, while the two commercially available additive-water solutions were statistically equivalent to water alone.

Jan 1, 1992

By S. K. Kawatra, S. J. Ripke

Iron ore pellets use bentonite clay as binder at dosages from 0.5to 1.0% (10 to 20 pounds per ton) of moist iron ore concentrate. Bentonite is typically shipped hundreds of miles from Wyoming to the Lake Superior iron ore district. It is therefore best to know how effective a bentonite will be before it is shipped and used to bind concentrate into pellets. Current tests of bentonite effectiveness include: plate water absorption, methylene blue uptake, free swell, exchangeable cations, and glycolated layer expansion. However, these tests have many disadvantages: First, they only measure the ability of a bentonite to expand, disperse, or absorb, not how well it will bond. Second, most of the tests require up to 20 hours to perform. Bentonite only has a few minutes to interact within the concentrate before it is indurated (sintered). These long-term tests may not reflect the true behavior of bentonite. Third, the tests are tedious and often results are inconsistent between different iron ore concentrates, labs, and technicians. Fourth, some of the testing equipment is difficult to procure. Fifth, procedures are often difficult to standardize. In this paper, the Binder Effectiveness Strength (BESt) test to evaluate binders for iron ore pellets is presented that: measures the ability of bentonite to bond, requires only about two hours to complete, is simple and reproducible, and utilizes readily available equipment that has been standardized for decades.

Jan 1, 2003

By Péter Siklósi, János Zámbó, Károly Solymár

It is fundamentally important to evaluate bauxites in a realistic, commercial way on the basis of the processing technology both for the supply of existing alumina plants and for the designing of new ones. The evaluation system developped by ALUTERV-FKI consists of chemical, mineralogical, texture and technological testing. The commercial value of bauxites is basically determined by their available alumina content and the caustic soda consumption required for their processing. However, their contaminants have to be taken into consideration, too. The commercial value of bauxites also depends on the processing technology and their possibly unfavourable chemical and mineralogical composition can be /at least partially/ compensated by R&D efforts. The selection of the optimum processing technology and the effects of further developing the same are demonstrated on monohydrate bauxites containing goethite and carbonates. Some of the technological solutions /desilication or deironing of bauxites, hydrothermal treatment of the digestion residue / make at the same time possible the complex processing of the bauxites, the profitable utilization of their main components.

Jan 1, 1984

By D. Harris, M. Osterberg

This paper examines the economics of acquiring mineral exploration rights by royalty-rate bidding when the royalty basis does not provide for full cost recovery. Bidding takes place prior to exploration and the documentation of actual tonnage and grade. Consequently, it increases considerably the risk to exploration capital when the fraction of cost recovered is small and the product price exhibits large fluctuations. Price and grade risk are demonstrated on a 360-Mt (400-million-st) porphyry copper deposit by Monte Carlo simulation of discounted-cash-flow analysis. Copper price is modeled as a stochastic price process, and costs are based on US Bureau of Mines cost models. When both grade and price risk are considered, the probability for a negative NPV is 0.54, given a royalty rate of 5% applied to a basis that allows the recovery of costs up to 50% of product price. Investment risk could be considerably reduced by defining the royalty basis to allow greater cost recovery. Although such a basis would require society to share in the risk, society would benefit from greater resource development.

Jan 1, 2000

By Greg T. Saretzky, Wilson G. Ward

A comprehensive hydrologic study was completed far the waste rock dump at Equity Silver Mine, BC. Characterization of the hydrologic system included geologic structure. topography, surface hydrology and groundwater systems. The results of the study conclude that the cover system is restricting net infiltration to approximately 5%. However, significant discharge continues to occur from the perimeter of the dump. A three dimensional seepage analysis was carried out to illustrate the influence of groundwater discharge associated with the regional topography and geologic structures. The results of the modelling program show that groundwater discharge occurs from the waste rock dumps when high recharge rates are specified for the surrounding topography- This groundwater discharge strongly influenced by the high hydraulic conductivity assumed far the fractured bedrock. The modelling results are considered preliminary and field drilling and piezometer installation is being conducted to determine the groundwater regime in the vicinity of the waste rock dump.

Jan 1, 2000

By M. A. S. Martins, H. Medeiros, B. Y. B. Dos Santos

This paper contains the geometallurgical studies, performed for Mineração Rio do Norte bauxites, applied to a selected area belonging to Plateau Saracá III, referring to an exploitation period of one year and three months, approximately. It is worth mentioning that Mineração Rio do Norte has the biggest bauxite operation in Brazil producing 8,500,000 tons of concentrate per year. The studies included wide investigations directed to the final objective of establishing a precise mining and production planning, based on the different behavior of the distinct bauxite ores, when submitted to industrial processes. Geometallurgy can be defined as the study of the regionalization (space distribution) of the metallurgical variables of a mineral deposit. This study involves and integrates all process engineering, geology, geostatistics and mining planning, among others. The development and application of the geometallugical studies to Mineração Rio do Norte were motivated by several reasons and necessities, among them: 1. Improving the forecast of the amount of concentrate (metallurgical mass yield) produced; 2. Improving the equipment operational efficiency, providing a more homogeneous feed; 3. Conducting a more precise material balance that permits a better daily, monthly and yearly production control; 4. Improving the forecasts for the final products generated by each ore type; 5. Obtaining better knowledge of the behavior of several ore types, submitted to the different process unit operations; 6. Promoting adequate ore blending, producing an homogeneous feed during mining operation.

Jan 1, 1998

By J. Trouw, W. de Bruijn, A. van Sandwijk, R. H. Heerema

Differential reduction and expansion or shrinkage of hematite under the influence of intimately associated foreign oxides may be a source of stress formation and sinter degradation during blast furnace reduction. To study specific effects, synthetically prepared hematite powder evenly doped with 1 % by weight of several elements present as oxides, was pressed into tablets and sintered at high temperature prior to reduction. Continuous theimogravimetric and dilatometric analyses were performed on the sintered tablets as these were being subjected to reduction under simulated blast furnace time/temperature/gas composition conditions up to 1183 K. These findings were coupled with observations on the microstructure of tablets removed from various stages of the reduction process. The results indicate that the degree of expansion or shrinkage of hematite during reduction is highly dependent upon impurities associated with the original material; marked differences in reduction rate and microstructure were observed as well. An important finding is that the influence of a particular additive can also strongly vary from one reduction stage to the next. The reduction behavior appears to be affected by the physical and chemical nature of the associations formed by the added elements.

Jan 1, 1990

By J. A. Hrabik

The feasibility of mining deep phosphate deposits by a borehole mining system was compared with mining by proven conventional techniques. An economic comparison of the borehole mining system with conventional dragline and bucket wheel excavator mining systems was completed at various mining depths and production rates. Hypothetical phosphate deposits, with various overburden thicknesses and reserve tonnages, were defined. Geologic conditions necessary for the application of the borehole system were identified. Discounted cash flow analyses based on derived capital and operating costs were used to generate rates of return and product prices. Borehole mining was found to be more economical where overburden thickness was 46 m (150 ft) or greater. However, at 15- and 30-m (50- and 100-ft) thicknesses, conventional surface mining was more economical. Overburden thickness has a great effect on the economic feasibility of the conventional mining systems but less effect on the economics of borehole mining. Economies of scale are only realized in conventional mining, since larger equipment is used to achieve greater production, whereas increased production from borehole mining is achieved using additional equipment units. A comparison of the environmental effects of borehole and conventional surface mining systems showed that borehole mining is environmentally more desirable.

Jan 1, 1987

By Zhongxue Li, Shuang Gao, Zhixin Zhen, Yiqing Zhao, Xuan Qin

If not well-managed, a mine-tailings facility may become a major source of risks, endangering the community and environment, and damaging the reputation of the minerals industry regarding sustainability. Identifying, characterizing, and mitigating the hazards and risks associated with tailings facilities have been critical to the maintenance of community-safe and environmentally sound mine-tailings facilities. Herein, a complex network model for characterizing the hazards and risks associated with the lifecycle of tailings facilities is presented. In this approach, the hazards are modeled as vertices of the complex network, and the interactions among the hazards are modeled as edges of the complex network. The complex network for modeling the hazard and risk spreading of mine-tailings impoundments is analyzed and characterized by using network metrics such as the network density, geometrical characteristics, characteristic path length, network efficiency, and clustering coefficient. The degree distribution of the network obeys a power-law distribution, indicating that the network for characterizing the risk spreading associated with a tailings facility is scale-free. According to the results of calculations and existing research results, the network is ultrasmall-world. By analyzing the change of the global network efficiency under four kinds of different methods to remove network nodes and edges, network nodes with higher between centrality (BC) are identified as critical. The removal of those critical nodes helps mitigate risks associated with a tailings facility and reveals the vulnerabilities to BC attacks.

Jan 1, 2017

By C. I. Wilmot, A. Sass, J. VanDeBeuken

Introduction This chapter addresses the need for operation manuals, presents an outline as a guide for writing the manual, discusses who should write the manual, suggests how it is implemented and gives tips to potential manual writers. Theory & Purpose of Operating Manuals The primary objective of the operating manual is to provide every operator the benefit of a uniform minimum level of training. This training is not only critical to the safety and efficiency of every employee, but also provides a basis for incorporating future operational improvements into standard and emergency procedures. The manual promotes safety through- out and additionally has a special section devoted to safety. The operator should be able to find information on chemical and physical hazards as well as be exposed to safety procedures for such items as motor lockouts and tank entries. The operating manual will usually reference a separate safety manual or incorporate parts of the safety manual. Safety is also promoted through standardized procedures for operation of equipment. Standardized operation is the second most important reason for the writing of manuals. If equipment is started, operated, and shut down in a consistent manner, then operational efficiency should be maximized. If it is not, then the procedure is adjusted until it is. The experience of many can be condensed into set responses for start up, shutdown, steady state operations, and upsets. Implicit with the standardized operation objective is a minimum level of training the operator will receive by thorough familiarization with the manual. The ability to know the contents of the manual is a basic requirement for operator status. The operating manual serves as a basis for a training program both at the start of the new plant and as new operators are hired or promoted into the job. The operating manual is a collection of at least part of the knowledge that "key people" own and will cushion the loss of key personnel for whatever reason. The manual can only fulfill these lofty goals by being a dynamic document. Manuals must change as equipment is modified and superior techniques evolve. To be effective they must be periodically updated, so word processors and reproduction

Jan 1, 1986

By Alvaro Souviron, W. W. Atkinson

The porphyry copper deposit at Los Pelambres is a resource exceeding 2 Gt (2.2 billion st) of 0.7% copper and 0.02% molybdenum. It includes a high-grade zone of +1% copper that is amenable to open-pit mining with a low stripping ratio. Metallurgical testing has indicated that the ore has exceptional characteristics, and that recoveries of 96% for copper and 93% for molybdenum can be obtained by conventional flotation methods. This paper summarizes the history of the prospect, the geology of the ore body and the surrounding area, and the procedures and results of exploration.

Jan 1, 1987

By J. Y. Hwang, M. L. Jeong, R. C. Greenlund

Various aluminum-smelting by-products from three production sources were received and characterized. The waste materials were tested for compound identification and environmental acceptance. A coarse metallic aluminum recovery test using an Eddy Current separator (ECS) was performed using two different Circuit configurations. White dross performed equally well with either Circuit, while black dross processing shows significant difference on the separation results. It was found that ECS technology was effective for particle sizes down to 6-10 mesh.

Jan 1, 2001

By Young C. Kim

Determination of the minimum sampling requirements of the run-of-mine (ROM) coal is very important for the purpose of meeting contract specifications. It is also important for the purpose of meeting emission regulations at a coal-burning power plant, such as the one located at Homer City, Pa. The classical statistical sampling theory can be applied to this problem, if ROM coal samples are known to be spatially (or serially) uncorrelated. On the other hand, the estimation variance concept from the Matherson's geostatistics must be used, if the samples are spatially correlated. Conditional simulation technique combined with simulation of the existing mining method is used to determine under which circumstances ROM coal samples do not preserve the spatial correlation. Only after establishing the degree of correlation that exists among ROM samples, an optimal sampling scheme can be devised using either the classical statistics Or the geostatistics. The minimum required sample volume can then be calculated using the well-known Gy's formula. This paper describes the results of the above investigation using the Helen coal mine data of the Homer City Owners. Empirical guidelines for determining the degree of correlation are also provided for coal mine operators.

Jan 1, 1986

By J. C. Norman

The boron review did not arrive in time for publication in the June issue. The United States was the world's largest producer and consumer of boron compounds during 1992. The US Bureau of Mines estimated that boron mineral concentrate and chemical production in the United States totaled 1Mt (1.1 million st) in 1992, yielding 521 kt (574,000 st) of B203 for a total estimated value of $333 million. That was about 20% less than 1991 revised production figures, and less in value by $107 million. The United States continues to provide essentially all of its own boron supply while maintaining a strong position as a source of sodium borate products and boric acid to foreign markets. Domestic employment in the mining and beneficiation of boron products in 1992 was about 900 people, the same as in 1991. In 1988, 1250 people worked in the boron industry. The Bureau estimated that total world production of boron in 1992 was about 3 Mt (3.3 million st), or about 1.2 Mt (1.3 million st)of B2O3. World production in 1992 was about equal to revised 1991 levels. US production Mines and processing operations in southern California were the only domestic sources of boron mineral concentrates and chemicals. US producers, in order of quantity of production, included:

Jan 1, 1993

By Jerzy Iskra, Wlodzimierz Sikora

INTRODUCTION The effect of stress concentration in coal seams leads to a sudden release in the form of rock bursts. This effect is controlled along many lines, but the most efficient methods consist in preventing the accumulation of energy in the seam or in the roof. The over- burden weight resulting from mining is the main cause of excessive stresses in a seam. An additional weighting of roof takes place due to formation of abutment loads. The accumulation of energy in the roof takes place where thick sandstone beds occur in overburden strata. An essential problem is to watch, with appropriate measurements, the stress of coal and roof rocks, and to conclude, on this basis, the degree of rock burst hazard. The methods for determining the stresses in a coal seam are quite well developed at present. Let me mention here the seismoacoustic methods, or borehole overcoring measurement methods. On the other hand, an examination of the state of stress in the roof rocks is almost impossible at the actual stage of development of the measuring technique. Hence, the model of stresses in roof was analyzed and determined theoretically. Based on this model, a technology for roof fracturing was developed which aims at destressing rock masses in a planned way. The essentials of the fracturing method consist of a controlled breaking of sandstone roof beds in order to: - prevent the excessive weight on the pillar - prevent a spontaneous breaking of roof beds at a limiting state followed by sudden energy release. High pressure fluid infusion is used to release buildup of stresses. THEORETICAL AND RESEARCH BASES According to the tests carried out by A. Kidybinski by the method of finite elements, isobars of stresses occurring in the roof over the working face are shown in [Fig. 1]. The results indicate: - the highest values of compressive stresses occur in the roof directly over the seam, at a distance of about 5 m ahead of the working face - at a distance of about 22 m above the seam there is a line of transition of compressive stresses into tensile - within the tested roof area, the highest tensile stresses occur at a vertical distance of 35 m, and at a horizontal distance of 20 m from the line of the working face. H. Gil (1) determined the pres- sure initiating the fracture of roof rocks by the formula: [ ] On the basis of results of analysis of isobars, and of the initiation of failure stress formula (1), isobars may be designed for a given roof class. Assuming for sandstones the Poisson ratio equal 0.3, a field of failure stresses presented in [Fig. 2] is obtained. In this figure it can be seen in which areas the effects of sandstone breakage may be obtained with the operation of a determined hydraulic pressure. To use formula (I), the knowledge of Rr is still necessary. This value may be determined in two ways: - taking a sample and testing it in the laboratory, if there is access to roof rocks in the existing openings, - drilling boreholes in the roof from surface and examination of the rock mass by using hydraulic breaking, if there is no access to roof rocks.

Jan 1, 1982