Search Documents

By Michael E. Allen

The building of sanitary and storm drainage sewers in urban or environmentally sensitive areas often requires the use of tunnel construction procedures. While hydraulic considerations may require only small diameters, traditional tunneling techniques make small sizes the least economical. Current state-of-the-art techniques using highly mechanized systems of pipe jacking can provide cost effective solutions to the problems of construction of small size tunnels. The characteristics of mechanized pipe jacking allow rapid advances under difficult ground conditions. The basic pipe jacking cycle is used with a variety of excavation systems to permit the contractor to satisfy engineering as well as economic parameters. These characteristics and several of the systems available are outlined.

Jan 1, 1981

The implementation of NAFTA in January 1994 was expected to have small but beneficial effects on the Mexican economy, mostly through increased investments. Mexico's mining industry was especially likely to benefit, as mineral investment funds would be diverted to the now safer Mexico and away from similarly endowed but more risky Latin American mineral economies. The results during the past two years have shown that it is government and macroeconomic factors that influence investment flows, rather than the fine tuning of trade flows through so called “free-trade" agreements.

Jan 1, 1998

By Edward M. Dowey

This paper presents the excavation of the Roosevelt Island Valve Chamber, the final of three chambers in Stage One of New York City's Third Water Tunnel. The valve chamber and passageways 13 379.7 cu m (17 500 cu yd) are drilled and blasted. The rock is stabilized by grouted rock anchors. The 6.1 m (20 ft) diameter shaft is drilled, blasted, rock bolted and wire meshed for a depth of 70.7 m (232 ft). Then shaft excavation proceeds with immediate concrete lining for another 120.7 m (396 ft). Two 6.1m (20 ft) diameter manifolds are excavated using heading and bench. The raise drilling of eight 3.7 m (12 ft) diameter laterals occurs during lower shaft sinking.

Jan 1, 1987

By V. A. Khartcenko

As the environment conditions deteriorate with the intensification of mining, the problems of mineral resources protection and the development and introduction of various bio- technologies are becoming more pressing This paper is devoted to the description of an ecological simulation system, related to the exploitation of a mine in a given region. We suggest mathematical tools for solving the main problem, namely an expert system, providing the simulation of ecological models for the mining complex. On the basis of the suggested models, algorithms, and software facilities, numerical modeling was carried out, as well as systematic investigation and processing of the mining activities of the complex. AS a result of this work we have obtained more effective parameters of technological and economical measures of environmental protection.

Jan 1, 1992

By Wolfgang H. Roth, Stephen J. Navin, Samuel K. Louis, Anthony F. Stirbys

This paper presents a case history of the design and construction of the access shaft and cross adit utilized to gain access to the Los Angeles Metro Rail tunnel alignment, at the A146 Contract site. The access shaft, a 14 m (45 ft) inside diameter structure, was constructed using ring beams and lagging with concrete backfill to a depth of 18.59 m (61 ft). The cross adit was hand excavated in sequential benches using liner plate, arch ring beams, and posts for support. The sequence of excavation and support placement are discussed. Soil conditions encountered at the project site are discussed together with the development of the design criteria. Instrumentation data collected during the excavation are also presented.

Jan 1, 1989

By Bradford F. Townsend, Gary Peach, Roger Rothenburger

From the experience of the authors on recent large infrastructure Design-Build projects this paper reviews major lessons for Contractors and Owners in the delivery of large Design-Build infrastructure projects and some major pitfalls and warnings to both Owners and Contractors. The paper is written from both the Design and Construction perspective. A case history is presented that details the approach employed to ensure a quality project consistent from the initial design phase through construction and outlines the strategy used to guide the Design-Build process to an acceptable completion. Suggestions are made for Contractors and Owners for handling the Design and the Construction elements of Design-Build contracts.

Jan 1, 2003

By W. J. Wuest, M. J. DeMarco

The US Bureau of Mines (USBM) recently developed a rock-mass classification system for evaluating the structural competency of bedded roof strata. The system is called the coal-mine roof rating (CMRR), When compiled with the companion Lotus 1-2-3 spreadsheet, CMRR data are a useful tool with applications to longwall gate-road pillar design, safety-hazard mapping and artificial roof-support analysis. This paper gives a review of some applications under actual conditions found in current US mining operations.

Jan 1, 1997

By Bruno Mattle, Max John

For tunnels with low overburden, the shotcrete lining is the main element of ground support, which is why shotcrete behavior is of prime importance. Following its application, shotcrete not only gains strength and stiffness with time but—if loaded at an early stage—it is also subject to creep which in turn leads to stress relaxation. For two-dimensional FE calculations, a computational modulus of elasticity of shotcrete is to be used. Based on parameter studies it was found that the modulus of elasticity of shotcrete depends on both shotcrete mix and ground behavior. While the Young’s Modulus used for young shotcrete may range from 1,000 to 7,000 MPa, the Young’s Modulus used for hardened shotcrete is best represented by a value of 15,000 MPa.

Jan 1, 2003

By Burt Ensley, Viatcheslav Dushenkov, Ilya Raskin, David E. Salt

Roots of many hydroponically grown terrestrial plants, including sunflower (Helianthus annuus L.) effectively remove toxic metals such as Cu+2, Cd+2, Cr+6, Ni+2, Pb+2 and Zn+2 2 from aqueous solutions. It should be possible to scale up this process such that plant roots can be used to treat large volume aqueous waste streams. It can be extrapolated from laboratory results that to reduce the Cd concentration in a waste stream, from 1 ppm to below 4 ppb, with a flow rate of 4000 L/min, would require 3500 sq. m of plant roots with a density 5 kg fresh weight per sq. m. These results suggest that the roots of hydroponically grown terrestrial plants may provide an attractive alternative to the accepted water treatment technologies.

Jan 1, 1995

By I. Iwasaki, J. N. Orlich

The effect of slurry rheology and ball coating characteristics on the abrasive wear of grinding media and the rate of grinding were studied using -10 mesh quartzite in laboratory marked ball wear tests. Pulp viscosity was found to be closely related with both the thickness and physical characteristics of the coating affecting abrasive wear. The packing density of particles at the ball surface was the primary determinant of wear while the grinding rate was more dependent on viscosity and thus the ball coating thickness. The optimum grinding rate was achieved when the coating thickness was about twice the largest particle size.

Jan 1, 1988

By M. A. Cristovici

The use of surfactants as wetting agents to suppress sulfide ore dust has been investigated. Numerous surfactants were examined to determine their characteristics and to investigate their ability to improve the wetting of the sulfide ore dust. However, the surfactants selected as suitable dust suppressors proved to have a negative effect on the flotation of ore contaminated with such reagents. A method was developed to eliminate the detrimental influence of dust-suppressing surfactants. It consisted of surfactant adsorption on activated carbon and separation of loaded carbon prior to flotation. The technique is simple and requires minimal changes in the plant flowsheet.

Jan 1, 1992

By Peter J. Alderson, M. P. Evans

The application of conveyor belting in bulk materials handling is crucial to the success of most mining enterprise selection of the cover rubber grade and thickness has a direct bearing on the cost per ton conveyed. Current and future demands placed on belt covers by higher speeds, increase capacities and greater lifts means today's cover will not be adequate for tomorrow's applications. The simple selections of RMA Grade I and I1 and MSHA above and below ground need to be expanded upon. This paper describes various new approaches for selecting conveyor belt covers for specific applications. It also presents examples of material and compounding techniques available to the belt manufacturer to improve the performance of their covers.

Jan 1, 1996

By A. S. Moss, J. Linkous

Where difficult shaft sinking conditions exist, it may be appropriate to use a blind drilling technique. The success of the method is in part due to the presence of a drilling mud which fills the shaft void during excavation. The mud performs two important functions with respect to shaft stability: it reduces the influence of groundwater; and, due to the mud weight, gives a positive sup- port to the shaft walls. The application of the method is illustrated by a case history which traces the development of a shaft from the initial investigation to determine the shaft location, through the evaluation of wall stability and mud requirements, to the shaft sinking contract and actual conditions encountered.

Jan 1, 1986

By Kevin D. Lofftus

This paper presents a dynamic model for column flotation. The model equations are normalized and the dimensionless groups that are directly responsible in determining the column flotation behavior are identified. The resulting model equations are incorporated for computer simulation. Numerical results from computer simulations are analyzed to gather information about design and operation of column flotation devices.

Jan 1, 1988

By Fred D. Wright

In this paper the principal theories used to design roof bolting systems are presented and discussed. Then the characteristics of various types of roof bolts are presented and finally the interaction between rock and roof bolt characteristics on choice of roof bolts is discussed. Theories can be considered design tools which may or may not be appropriate for a specific situation. It is good for a design engineer to have a number of such tools available and also important that he understand their good features as well as their limitations. Hence, some of the principal theories and classification systems used for design of roof bolting systems are discussed first.

Jan 1, 1982

By B. Huang, H. Sevim, R. Honaker

The use of medium-to-high sulfur coals has been negatively impacted by the 1990 Clean Air Act Amendment (CAAA). In this article, a method is demonstrated that can render these coals competitive and yet compliant with Phase II of CAAA. The method uses strategic mining and optimized preparation plant operation to minimize production costs, and it utilizes advanced coal-cleaning technology and an SO2 allowance to produce a compliant coal. The method is illustrated through an example from southern Illinois. For an annual production of 3.2 Mt (3.5 million st) and with a $150/st SO2 allowance cost, it was possible to produce a competitive coal for $0.84/million Btu. The production and allowance costs were $0.608/million Btu and $0.232/million Btu, respectively.

Jan 1, 2002

By John A. Bischoff, Francis S. Kendorski

A technique that has been used for inspection and appraisal of rock tunnels is described. It enables a rapid and complete record to be made of those factors necessary for the engineering assessment of the rock conditions surrounding a tunnel. Full understanding of the regional geology, and a careful recording of data concerning the principal geological and construction factors is essential basic data for a tunneling project, whether the tunnel is under construction or is already in service. A methodical recording of data concerning general geology, shears, fracture orientations, spacing, persistence, rock classification, water condition, shear frequency, excavation method, blasting procedure, and rock stabilization and support methods, combined with a photographic record, can be completed by experienced engineers and geologists at the rate of over 1000 feet of tunnel per shift.

Jan 1, 1976

By D. Harney

Accurate measurement, tracking, and planning are vital for efficient utilization of energy in any mining operation, the major focus of this paper. This can be done with a number of assessments: 1) accurately measure KWH usage and track peak demand periods first; 2) identify the electrical equipment that affects your usage and the conditions that require it to be running; 3) remotely monitor and control as much equipment as possible, especially larger pieces of equipment; 4) with your utility determine that you are on the most suitable rate for your usage profile, then understand how your utility company calculates your electrical bill; 5) recognize how production affects energy usage and utility costs; 6) keep historical records of everything you monitor; 7) make information, live and historical, available to everyone; and finally, with the knowledge of your equipment and energy needs, automate controls that you have identified to optimize your energy usage and time of usage.

Jan 1, 2007

By L. J. E. Hofer, L. F. Zeiler, D. A. Giardino

The Jones Trickett Ratio (JTR) is generally used in investigations of fires and explosions for the determination of the composition of the fuel. This paper takes a close look at the JTR and finds it unreliable and ambiguous for the determination of fuel composition. A new index is presented, termed the (H/C) Index which uniquely determines the fuel composition. The (H/C) Index is simple to use requiring only the results of a single gas analysis of the combustion products. Experimental data testing the (H/C) Index for methane, propane, ethylene and coal dust are given, showing that the Index unambiguously determines the composition of the fuel. The (H/C) Index is also applied to the gas analysis data of several mine fires, illustrating how the Index changes with the progression of the mine fire.

Jan 1, 1993

By G. Myers, C. J. Wendt, W. H. Wilkinson, M. D. Dennis

Precious metal mineralization at Mt. Hamilton, NV is associated with a polymetallic, garnet-pyroxene skarn system developed in middle to upper Cambrian calcareous shale, limestone, and dolomite. The skarn is developed around the Cretaceous Seligman and Monte Cristo calc-alkaline stocks. Gold is associated with intense retrograde alteration. Later epithermal quartz veins contain gold, silver, base-metal sulfides, and sulfosalts cross-cut skarn alteration. Westmont Mining Inc. is currently developing two mineralized zones containing a geologic resource of about 7 Mt (7.7 million st) that averages 1.7 g/t (0.05 oz per st) gold and 17.2 g/t (0.5 oz per st) silver. The project will have an estimated mine life of seven years, with a planned annual production rate of I t (35,000 oz) of gold and 9.3 t (300,000 oz) of silver.

Jan 1, 1990