Search Documents

By D. Pappas

Over the past decade the number of contractors working in underground coal mines has nearly doubled; however, the effect this has had on the industry?s injury rates has been the subject of much speculation. The confusion exists because the U.S. Mine Safety and Health Administration (MSHA) database does not assign contractor hours to the individual mining operations where they worked. To better understand the safety record of the contractor segment of the industry, the National Institute for Occupational Safety and Health (NIOSH) undertook a comprehensive analysis of the data contained in the MSHA database. The first part of the study compared overall contractor and operator trends from 1983 to 2009 related to employment, hours worked, injury rate, and days lost. One unexpected finding was that the larger contractors tended to have higher injury rates than the smaller ones. The second part of the study directly addressed the role of contractors on the safety record of 10 large underground coal mines. A detailed analysis provided both injuries and estimated contractor hours worked at these mines for the period 1992?2007. Comparison between the estimated contractor injury rates and the reported operator injury rates at these mines indicated that the contractor injury rates were significantly higher at most of the operations studied. However, the industry-wide data indicates that contractor and operator injury rates have converged since 2005 and are now equivalent.

Jan 1, 2011

By Maryam Motamed, Jeremy Stone, Leigh Anne Zhang

Controlling and predicting ground movements are essential to the design of shoring systems. The Courthouse Commons tunnel in San Diego, California, included a 56-foot-deep temporary shaft as a launching point for tunneling using the Sequential Excavation Method (SEM). The rectangular shaft was unique in that it was surcharged on one wall by an 11-story building and employed a hybrid support of excavation design. An array of geotechnical instrumentation was used to monitor lateral and vertical movements at the ground surface. This paper compares the measured ground movement with the predicted ground movement from various excavation stages

Dec 1, 2022

By S. K. Sahoo, S. K. Sharma, U. K. Singh, G. S. P. Singh

This research focuses on the strata control issues in a Bord and Pillar depillaring working under the influence of dead load condition of voluminous and fragmented softcover of overburden dump material. It reports the modeling of a mine working through the FLAC 2D software under the Indian geo-mining conditions. The modeling results of an actual mine working under softcover were compared with that under the intact overburden condition to assess the influence of the soft overburden over the depillaring working. The modeling work involved progressive caving of the strata and the cyclic goaf filling following the modelsimulated occurrence of main fall and periodic caving. Mohr-Coulomb Failure criteria along with a simplified strain-softening (MCSS) model was used to study the failure and caving mechanism. Salamon’s compaction model was used to simulate compaction and resultant stress recovery in the goaf material. Comparison of the model findings was done in terms of load on supports, abutment stress, and convergence, apart from the stress redistribution and failure mechanism. The load transfer mechanism of the soft overburden was also studied for an overall understanding of the strata behavior in such workings.

Jun 16, 2020

By David Dardick

Tround International Inc. is developing rock excavation and drilling devices which utilize a simple patented mechanism for firing frangible projectiles. This system launches a salvo of three projectiles with every shot in automatic sequence. Studies conducted by Physics International Inc. have demonstrated that firing projectiles into hard rock such as granite creates fragmentation which is much faster and cheaper than conventional drilling and blasting. The Tround salvo approach enhances this further by a controlled stresswave interaction created by a slight time difference during impact of the individual projectiles. The University of Maryland is conducting additional studies to optimize these parameters.

Jan 1, 1981

By P. Burmeister, R. A. Errath, A. Sapin

Sag Mills are becoming bigger in size almost every year. Concentrator plants are also becoming larger with more SAG and Ball Mills units with Gearless Mill drives installed in one plant. In contradiction to this development, concentrator plants are being built in increasingly remote areas, where the power supply and network conditions are not necessarily covering the needs for the operation of such plants. This paper describes sources of harmonic distortions and possible approaches to solve this problem. It also illustrates the permissible tolerances in terms of commutation of power electronics, based on already realized installations. Furthermore it explains how, and with which measures, harmonic currents created by non-linear loads with SAG and Ball Mill drives can be handled, and how harmonic standards can be fulfilled accordingly. Finally, this paper gives an overview about the technical impact of a strong versus weak network, and the economic relationship between them.

Jan 1, 2001

By WILLIAM M. CROSS, ALBERT ROMKES, BERNARDO MORENO BAQUEIRO SANSAO, Jon J. Kellar

In this research study, the interaction of particles with substrates of different roughness magnitude was investigated. Particle surface treatment, relative humidity (RH), and surface roughness levels were controlled in order to achieve separation of different particles by applying removal forces. Three different approaches to reproducibly roughen surfaces were used. Initially, glass disks were laser engraved to create a reproducible, controlled roughness substrate. However, the laser engraving method produced surface features that were much greater in scale than the particles. These scale differences were such that the substrates produced were not of value to this research. The second option investigated to induce reproducible substrate roughness was to scratch the glass disk using sandpapers of known grain size. A third approach to establish reproducible roughness was to use fine stainless-steel wire mesh substrates. In tests with sanded glass disks, the interfacial energy of plasma-cleaned (hydrophilic) glass beads had a high variation at 40% RH, showing non-uniformity of area of contact between particles and substrates. As the RH increased, it was expected that the interfacial energy of hydrophilic particles would increase, but this behavior was not observed. In addition, comparing the interfacial energy results of hydrophilic particles with hydrophobic particles, a region with significant interfacial energy difference was not identified. In the case of the stainless-steel mesh substrate, the mesh asperities and particle dimensions were comparable. Thus, the smaller particles had more area of contact with the substrate than the larger particles. For the plasma-cleaned (hydrophilic) beads, the recovery values had an average of 92.5% recovery when the RH was between 46 and 85%. For the hydrophobic beads, the average recovery was 19.0% when the RH was between 46 and 75%. Thus, the hydrophobic characteristic of the particle influenced its lower interaction with the mesh substrate. The difference in recovery can be exploited to achieve separation of particles based upon adhesive forces.

Nov 30, 2021

By E. Knell

COM Energy, Inc., a subsidiary of Occidental Petroleum Corporation, has constructed a 1.6 million hectoliter-per-year COM plant in Jacksonville, Florida. COM will be distributed to customers in the region as a substitute for fuel oil presently burned in boilers and kilns. As the market for COM grows, COM Energy, Inc. expects to build additional units both in this country and overseas. This paper addresses the overall status and technical aspects of the project, focusing on the facilities for COM production and utilization.

Jan 1, 1982

By Xuezhong Wang, Hao Guo, Tao Tu, Qingsheng Liu

The scheelite concentrate was leached with a mixture of sulfuric and oxalic acids. Chemical compositions, mineral phases, and morphology were characterized by XRF, XRD, and SEM–EDS. Based on the results of the single-factor experiments, the response surface methodology (RSM) was chosen to optimize the leaching parameters: temperature, time, and concentrations of sulfuric and oxalic acids. The RSM results indicate that the optimum values for those parameters are as follows: temperature 72 ℃, sulfuric acid concentration 1.48 mol/L, oxalic acid concentration 0.96 mol/L, and reaction time 2 h. Under the optimal leaching conditions, the model predicts a maximum leaching yield of 99.5%, compared to the value of 99.1% obtained experimentally, that is, a discrepancy of only 0.04%. This good correlation shows that the quadratic polynomial equation obtained by the RSM optimization is reliable. The importance on leaching parameters of scheelite is, in decreasing order, temperature, time, sulfuric acid concentration, and oxalic acid concentration.

Oct 11, 2021

By Yanxu Shen, Cheng Liu, Zhijie Chen, Hao Chen, Huimin Gao, Zijie Ren

Fluorite, a kind of critical non-metallic minerals, is the primary source of industrial fluorine. Sodium oleate (SO) is commonly used as the collector of fluorite ores. However, because of its some features (such as the low solubility, high solidifying point, and poor dispersion of SO) at low temperatures, it profoundly inhibits its collecting ability as well as the flotation performance. Herein, we have developed a low-temperature-resistant collector for the efficient flotation separation of fluorite from quartz. The advantages and disadvantages of the SO and sodium petroleum sulfonate (SPS) were analyzed by comparing the performance under different temperature conditions. The results of flotation tests suggest that SPS exhibited much better collecting performance than SO under low temperature. The flotation mechanism of the two collecting agents were further analyzed by contact angle measurements, zeta potential measurements, Fourier-transform infrared spectroscopy (FT-IR), and flotation kinetics. The results indicated that both collectors can selectively undergo electrostatic and chemical adsorption with fluorite, with no adsorption on quartz surface. The sulfonic acid group in SPS is a hydrophilic functional group, which has a relatively higher solubility in water. Therefore, the water solubility of SPS is better at low temperatures.

Sep 30, 2021

By James R. Walpole

Less than 100 years ago the first major federal regulatory agency, the Interstate Commerce Commission was established (in 1887), and since that time literally hundreds of other federal agencies have been created. The regulations set by these agencies tremendously affect the individual citizens of this country as well as U.S. institutions. A few examples of the myriad agencies established include the Food and Drug Administration. (1907), the Bureau of Mines (1910), the Federal Reserve System (1913), the Federal Trade Commission (1914), the Tennessee Valley Authority (1933), the Securities and Exchange Commission (1934), the National Labor Relations Board (1935), the Small Business Administration (1953), the Federal Maritime Commission (1961), the Equal Employment Opportunity Commission (1965), the Farm Credit Administration (1971), etc., etc. Eight years ago, on December 2, 1970, still another federal agency was established by the reorganization plan of President Nixon -- the Environmental Protection Agency (EPA). The Administrator of EPA was given authority to regulate certain activities affecting the environ-ment, which were formerly within the jurisdiction of the Department of Interior, the Department of Health, Education and Welfare, the Federal Radiation Council, the Atomic Energy Commission, the Department of Agriculture, etc. Within weeks after the formation of this Agency, Congress began to enact legislation which would be administered by EPA. Over the last eight years a considerable number of such laws have been passed, a few of which include: the Clean Air Act (1970), the Noise Control Act (1972), the Federal Water Pollution Control Act (1972), the Marine Protection, Research, and Sanctuaries Act (1972), the Federal Insecticide, Fungicide and Rodenticide Act (1973), the Safe Drinking Water Act (1974), the Toxic Substances Control Act (1976), the Resource Conservation and Recovery Act (1976), the Clean Air Act Amendments of 1977, etc. It may be helpful to review, in a summary fashion, the major provisions in some of these statutes, and accompanying regulations, as they relate to water quality control in the mining industry. The Safe Drinking Water Act and the Federal Water Pollution Control Act contain provisions to be examined, as well as the Resource Conservation and Recovery Act and the Toxic Substances Control Act. One other law, the Surface Mining Control and Reclamation Act (1977), is not administered by EPA although it does contain many provisions related to environmental control, and it will also be dis-cussed because of its importance to the mining community.

Jan 1, 1978

By D. H. De Jager

Fluorapatite is an important constituent of the greater part of the basic and ultra-basic rock members of the Complex. The evidence for and role of primary magmatic processes in the development of concentric zones of dunite, pyroxenite, syenite and carbonatite and its consequent bearing on the distribution of apatite are discussed. The presence of at least two generations of each of the latter three rock types indicates the cyclical nature of magmatic activity. Pegmatitic-metasomatic phases corresponding to the major magmatic cycles resulted in emplacement of pegmatoidal assemblages. The abundance of apatite in the pegmatoid can be traced to the composition of its parent magma and its cooling history. Approximately 2.5 million tonnes of phosphate concentrate are produced annually from ores containing from 10 percent to 25 percent apatite.

Jan 1, 1978

By Robert Labbe

The final tunnel lining for this project involved pumping vast quantities of concrete over large distances under the extremely busy streets of lower Manhattan. Approximately 68,000 cubic meters (89,000 cubic yards) were pumped from various locations over 152 meters (500 feet) below ground (Figure 1) to create nearly 14.5 kilometers (9 miles) of 3.05 meter (10 foot) diameter tunnel. Total distances pumped exceeded 1,645 meters (5,400 feet) horizontally after a vertical difference of over 152 meters (500 feet). The urban setting of the operation, coupled with the long distances over which concrete was pumped, created many problems which had to be dealt with along the way. A three-shift labor operation was implemented to allow sequential pouring of tunnel sections nearly every day. The fine tuning of the mix design was critical to make this operation successful.

By S. A. McGhee

Introduction ASARCO's Ray Operations include an open-pit copper mine in the Mineral Creek Mining District of Pinel County. The district is located in east central Arizona, 132 km (82 miles) southeast of Phoenix, AZ, and 126 km (78 miles) north of Tucson, AZ. The mine lies 8 km (5 miles) north of the Gila River in Mineral Creek Valley, between the Tortilla Mountains to the west and the Dripping Springs Range to the east. The rich copper deposits of the Mineral Creek mining district were first noted by a US Army Officer in 1847. The Ray Copper Company was the first major operation in the area. The company was named after the Ray mining claim, which was one of the earliest recorded claims. After decades of sporadic and unsuccessful mining ventures, the Ray Consolidated Mining Company was formed in 1910. The company introduced one of the first successful block caving operations in the world. In 1933, the Kennecott Copper Corporation acquired the Ray Consolidated Mining Company and continued operation of the mine under the same name until 1943, when the property was renamed the Ray Mines Division of Kennecott. Underground mining continued until 1955, when the mine was converted to an open pit operation. In November 1986, ASARCO Inc. purchased the Ray Mines Division and related facilities from Kennecott. The purchase also included the Hayden concentrator and the Ray Smelter, located approximately 32 km (20 miles) from the Ray Mine. This paper summarizes the 54,400 tpd (60,000 stpd) in-pit crusher and overland-conveying system and the 24,200 tpd (30.000 stpd) copper SAG concentrator and tailings disposal system constructed at ASARCO's Ray Complex - Ray Operations. General description of facilities The Ray concentrator includes a sulfide SAG concentrator, a "relocatable" in-pit primary-crushing plant and overland-conveyor system, a concentrator tailings-disposal system and plant ancillary facilities, The major elements of the project include: • A relocatable Fuller-Traylor in-pit 1524-mm (60-in) x 2261-mm (89-in) primary gyratory crusher at the 442 m (1450 ft) mine elevation. The crushing plant has a nominal capacity of 54,400 tpd (60,000 stpd) of sulfide ore. • A 1524-mm (60-in) wide x 1253-m (4110-ft) long overland belt conveyor, which runs from the in-pit crushing facility to a transfer station serving both the Ray Concentrator and the existing Hayden concentrator railroad load-out facility. • A 1524-mm (60-in) wide x 152-m (500-ft) long stackerbelt conveyor, which delivers a nominal 27,200 tpd (30,000 stpd) of ore from the transfer station to a 23,600 t (26,000 st) live-capacity coarse-ore stockpile serving the Ray Concentrator. • A nominal 27,200-tpd (30,000-stpd) concentrator, including semiautogenous grinding, flotation, copper concentrate filtration and associated plant ancillary facilities. • A tailings disposal system. Flotation tailings are pumped from the Ray Concentrator to a 122-m (400-ft) diam. thickener, located 4.8 km (3 miles) southeast of the Ray Concentrator site. The thickener overflow is pumped to two 76.2-m (250-ft.) diam. concrete process-water reservoirs. The thickener underflow, at 45% solids, is pumped to a new tailings disposal site located at Elder Gulch. • An HDPE-lined temporary-containment area to collect material from Ray Concentrator plant upsets and local storm-water run-off from a 100-year, 24-hour rain event. •A reclaim-water system from the Elder Gulch tailing pond area to the Ray Concentrator. • A 610-mm (24-in.) diam. x 31.9-km (19.2 mile) long fresh-water pipeline from the Hayden fresh-water-well field system to the Ray Concentrator. The overall process design criteria for the new Ray Concentrator is based on a nominal throughput of 27,200 tpd (30,000 stpd) of ore at 90% plant availability. However, based on the maximum performance capacity of the installed grinding equipment, it may be possible to achieve a sustained operating level in excess of 36,300 tpd (40,000 stpd) when processing soft ores. The balance of this paper will cover the major process systems including:

Jan 1, 1995

By J. Navoyski, B. Macdonald, W. J. Helfrich, J. L. Bellanca, B. Demich

DISCLAIMER The findings and conclusions in this paper are those of the authors and do not necessarily represent the official position of the National Institute for Occupational Safety and Health, Centers for Disease Control and Prevention. Mention of company names or products does not constitute endorsement by NIOSH. ABSTRACT The pervasiveness of high-fidelity video games raises expectations of quality, detail, and lighting in virtual reality (VR) applications. However, high-quality models of mining equipment and environments are often not readily available, and developers may not be familiar with the latest techniques, such as physically based rendering (PBR). Because a consistent aesthetic is critical for maintaining immersion and controlling visual stimuli in research as well as in training, researchers at the National Institute for Occupational Safety and Health (NIOSH) created an asset development workflow. This paper details this workflow, including precision modeling and PBR techniques as well as a rigorous review process. It also describes lessons learned in the creation of photorealistic VR assets. BACKGROUND Virtual reality (VR) describes the simulated experience generated by an assemblage of hardware and software that are used to immerse the user. Over many years VR developers targeted the development of virtual environments (VE) toward various purposes: entertainment, the treatment of phobias [1], rehabilitation [2], and training [3]. A large part of the VE development includes digital assets, where digital assets refer to the non-programmed elements including 3D models, audio, and user interface. Because vision provides nearly 10Mbps of data [4] and accounts for the majority of all sensory input combined [5], a focused effort on asset appearance in VEs is warranted. Furthermore, research has shown that higher-resolution imagery increases search performance and training transfer, necessitating high-fidelity assets [6, 7]. In addition to being visually appealing, it is important that the assets and environment are also dimensionally accurate and consistent in order to elicit appropriate responses from the end users as they interact with and among these items [8, 9]. Researchers at the National Institute for Occupational Safety and Health (NIOSH) have developed VEs and digital assets under several research projects over the course of the last two decades [10, 11, 12, 13]. This work has provided researchers with a strong knowledge base for digital asset development. However, the assets themselves have had limited reuse value. Due to the extended timeframes and limited scope of these projects, the previously developed assets are not consistent in visual quality and dimensional accuracy. Moving forward, researchers wanted to minimize future development time and use of resources as well as adopt new asset development tools and game engine technology. Therefore, the aim of this paper is to document a new asset development workflow including geometry, materials, UV layout, and shader implementation combined with review steps in order to produce high-fidelity simulation assets that are accurate with consistent characteristics, using repeatable methodologies that are well documented.

Jan 1, 2019

By T. J. Lutz, D. S. Yantek, L. Yan, J. R. Srednicki, J. A. Yonkey, G. T. Homce

Federal regulations require the installation of refuge alternatives in underground coal mines. Of the inuse refuge alternatives, more than 95 percent are mobile refuge alternatives, with the remainder being built-in-place (BIP) refuge alternatives. Heat/humidity buildup has been one of the major concerns with mobile refuge alternatives. For BIP refuge alternatives, however, there is a lack of in-mine heat/humidity test data to determine the extent of heat and humidity buildup. To quantify heat/humidity buildup in BIP refuge alternatives, the U.S. National Institute for Occupational Safety and Health (NIOSH) performed a series of heat/humidity tests on a 60-person BIP refuge alternative with and without a borehole air supply. At various times during the year, tests were performed with cooled, heated or unconditioned borehole air to examine how various outdoor temperatures may affect the thermal conditions inside a BIP refuge alternative. The results show that the air supplied to a BIP refuge alternative may require heating or cooling, depending on the outside air temperatures and the temperature of the mine. For example, during tests with an external ambient temperature above 21 °C (70 °F) and a relative humidity of 90 percent, providing 13 °C (55 °F) dew point air at 775 scfm, which is slightly higher than the mandated flow rate of 12.5 scfm per person, kept the internal apparent temperature below the mandated 35 °C (95 °F). Results for each test case are presented.

Jan 1, 2018

By Derek J. Penrice

A critical element of the Transbay Transit Center Program, the Caltrain Downtown Extension (DTX) will extend commuter rail service into downtown San Francisco and accommodate future statewide high-speed rail service. The DTX project includes 1.8 miles of underground construction, comprising significant sections of mined and cut-and-cover tunnel. At the request of stakeholders, an updated cost estimate was prepared early in the project?s preliminary engineering phase. Unsurprisingly, this yielded a cost substantially higher than the available budget. This paper provides a summary of the management processes and planning decisions taken to bring the project back to budget, resulting in a configuration which derives maximum value from available funding and retains maximum flexibility for future system expansion.

Jan 1, 2008

By G. L. Dollinger, J. P. Kindsvater, J. A. Gibson

DESIGN AND DEVELOPMENT OF A MOBILE MINING MACHINE INTRODUCTION Until recently, developing tunnels in hard rock has been accomplished either by the drill and blast method or by using large tunnel boring machines. Combining the flexibility of drill and blast with the safety, efficiency and productivity of a TBM has been the objective of mining machinery producers for many years. In 1979 The Robbins Company began developing a new type of tunnel boring machine called the Mobile Miner to meet these objectives. The development and testing of the Mobile Miner is the subject of this paper. CURRENT MINE DEVELOPMENT METHODS Both the drill and blast method and the use of a TBM have notable advantages and disadvantages. The drill and blast method, for example, allows much more flexibility, requires less setup time and has a lower initial cost than a TBM; however it requires the use of high explosives and blasting has a disrupting effect on the rock surrounding the development. A TBM, on the other hand, is safer to operate, more efficient, more productive and produces smooth tunnel walls without disturbing the surrounding rock. In longer straight drifts it will easily out distance the drill and blast method. The TBM, however, is limited to boring a circular cross section tunnel which must then be modified if a flat floor is required. It also has a higher initial cost and an extended setup period.

Jan 1, 1985

By Tassos Grammatikopoulos, Mike Johnson, Niels Verbaan

Seabed polymetallic nodules, which contain significant quantities of metals key to electrification (nickel, cobalt, copper, and manganese) can be processed using several different metallurgical processing options, including direct smelting and subsequent hydrometallurgical refining of the copper/nickel matte, ammoniacal leaching (gas reduction or Cuprion), and acid leaching (often reductive). Many of these approaches suffer from reduced cobalt extraction, difficult physical performance, or overall circuit complexity in general, leading to increased risk to the overall project. SGS has considered pressure acid leaching of nodules for further investigation, as publicly shared data on this processing route stems from the 1970s and 1980s and is not always easily accessible. This paper will detail the series of tests conducted and provide updated results obtained (high Ni/Co/Cu recovery with limited Mn/Fe), as well as comment on the potential treatment options on the product solution and residue.

Feb 1, 2025

By L. J. Moore

Introduction Hydrometallurgical solvent extraction (SX) processes – featuring large quantities of combustible or flammable organic solvents - are common in the mining industry for recovering non-ferrous metals such as copper, nickel, cobalt, uranium, tungsten, iodine and lithium. Recent fire loss incidents and the widespread use of sub-grade tank farms and piping trenches, plastic piping, poor drainage, and closely spaced buildings demonstrate opportunities to improve the use of Inherent Safety (IS) in this industry. The mining industry has designed and constructed facilities with an emphasis on personnel safety, production efficiency and cost effectiveness. The use of IS to eliminate or minimize property fire exposures has not seen widespread practice. Lessons learned from the mainstream CPI have not been communicated or applied. As an example, copper SX plants have consistently used design of gravity flow as a cost and production-effective solution for transferring liquids and minerals through the process. In fact, Jergensen1 recommends to “utilize gravity to the fullest extent possible” in design of SX plants. This philosophy has been achieved by laying out SX plants with process equipment at different grade levels so that solutions can flow “downhill”. Because of the use of large quantities of flammable liquids and the potential for these liquids - if released – to flow unimpeded into other areas – gravity SX processes represent severe inherent fire consequences unless costly barriers, drainage and channeling are also provided. It appears that little thought has been given to the fire protection consequences and challenges of this design feature during the evolution of SX plants and most copper SX plants constructed today use some form of a sub-grade processing area (tank farm) and one-way gravity flow. While this layout is used to assure a cost effective operation it has resulted in significant exposures to high value production. The use of sub-grade production units is an inherently unsafe layout where flammable liquids are used and is a layout that would rarely if ever be used today by the mainstream CPI. Gravity-assist layout is only one example where copper SX plants have been designed and constructed without IS in mind. The use of combustible and frangible corrosion-resistant materials – such as glass, wood and plastic - for flammable liquid storage, processing and piping systems has significantly increased the hazards of these facilities. These materials of construction are not rigorous and allow for rapid failure and release of flammable contents during fire exposure. The use of combustible or frangible systems to handle or transport flammable liquids is not a practice seen today in the CPI.

Jan 1, 2006

By Behrooz Abbasi, Seyedsaeid Ahmadvand, Thom Seal, Babak Azarfar, Bryan Ulrich

Hydro-Jex® is a new enhanced method for heap leach treatment with significantly higher mineral recovery. In this case study at the Los Filos Mine in Mexico, the Hydro-Jex operation is evaluated for heap leach stability. This is pursued by numerical modeling of the heap leach pad stability and well monitoring of the phreatic surface before and after the Hydro-Jex operation. Experimental and numerical results both indicate an improvement in mineral processing under the influence of Hydro-Jex. Numerical results show an insignificant decrease and a significant increase in stability during and after Hydro-Jex injection application, respectively. The integrity of the liner is maintained in both cases. The zonal injection pressure, operationally below the overburden pressure, is found to be negligible compared with the dimensionality of the heap, and stability of the structure is not exposed to any significant risk, even up to 25%above overburden pressure. Furthermore, heap leach factor of safety increases after Hydro-Jex application. This is attributed to breakdown of the water solution build-up and thus a decrease in the phreatic surface depth below the top of the pad. It is suggested that injection wells be drilled, based on thorough geophysical data, in locations where overcompaction of heap material results in water solution build-up and pore pressure enhancement. Compared with traditional heap leaching, the Hydro-Jex technique not only expedites mineral processing by increasing chemical kinetics extraction but also increases the stability of the heap by unclogging drains.

Jun 29, 2020