Search Documents

By H. Kinilakodi, R. L. Grayson

In 2010, the U.S. Mine Safety and Health Administration (MSHA) began holding hearings on a new coal mine respirable dust rule, which proposed a 1.0 mg/m3 standard, a separate 0.1 mg/m3 quartz standard, and the use of single-shift samples for compliance. Small mines largely comprise the “hot spots” where dust diseases of the lungs increased dramatically over the past decade. This paper presents findings on the feasibility of small mines’ compliance with the proposed new 1.0 mg/m3 standard. It gives probabilities of noncompliance by MSHA district, average mining height and selected “hot spot” counties. Because silicosis and respirable quartz dust appear to be the primary issues related to a recent doubling of the prevalence of dust diseases of the lungs, multiple regression models for prediction of the average total quartz content of compliance samples are given. These findings have significant implications for the need for better dust control methods.

Jan 1, 2012

By Milton Gomez, Nico Sutmoller

Low-density cellular concrete (LDCC) was first introduced to the market in the early 1900s and since then has made continuous technological advances. There are two primary types of LDCC: permeable and non-permeable. Both types of cellular concrete offer advantages in different types of geotechnical engineering applications. Because of its unique characteristics of low density, high compressive strength, and high fluidity during placement, LDCC offers an effective solution for a wide variety of engineering applications, and in many cases provides a more cost-effective, labor saving alternative to traditional fill materials. This paper will review the history, characteristics, and technological advances of LDCC, highlighting multiple real-world case studies that showcase the high-performance capabilities of both permeable and non-permeable LDCC.

Dec 1, 2022

By H. Verakis, M. A. Hockenberry, A. C. Smith, J. H. Rowland III

Four different types of fire suppression systems were evaluated in large-scale fire experiments to study the effect of air velocity on their effectiveness in extinguishing conveyor belt fires. The four different types of suppression system were water sprinkler, deluge-type water spray and two different dry chemical fire suppression systems. The large-scale fire tests were conducted with 1.8-m- (72-in.)-wide fire-resistant rubber belt that met the Mine Safety and Health Administration flame resistant requirement specified in Title 30, Code of Federal Regulations, Part 18, section 18.65 (also known as the 2G Flame Test). Each fire suppression system was tested at air velocities of 152 - 168 m (500–550 ft) per minute (mpm) and 411 - 457 mpm (1,350 - 1,500 fpm). Two tests were conducted at both air velocities for each fire suppression system. Both of the water-based fire suppression systems were able to suppress the fire to the point that a miner could extinguish it with a fire extinguisher. However, the amount of water needed to suppress the fire to the point where a miner could walk up to and extinguish any smoldering belting was greater than the current MSHA regulations required. MSHA regulations only require 10 minutes of water supply for a suppression system. In the test setup, neither of these systems would have suppressed the fire had the water been turned off to the system after 10 minutes. The dry chemical suppression systems produced mixed results. Dry chemical suppression system A did not suppress the conveyor belt fire at either air velocity. Dry chemical system B suppressed the fire at 152 mpm (500 fpm) air velocity, but produced mixed results at the higher air velocity. Details are presented on the large-scale fire test setup, arrangement of the fire suppression systems and conclusions regarding the effect of air velocity on fire suppression system design and performance.

Jan 1, 2010

By James W. Estep

The sulphur shortage that has occurred in the past two years has directed attention more and more toward sour natural gas reserves, Wellhead values of sour gas vary widely depending upon the acid gas composition, location, market conditions, and necessary processing charges. Preparation of a saleable residue gas is considerably more involved and expensive than that normally encountered in treating a sweet gas. Recent revisions in sales gas specifications have increased capital costs and processing charges. The presence of hydrogen sulphide and carbon dioxide in a natural gas contributes to shrinkage factors that may approach 50%. Fuel required by the gas sweetening process and sulphur slant tail gas incineration also contributes to a further reduction in the volume of residue gas available for sale. The additional processing facilities involving gas sweetening, mercaptan removal, expanded utilities, sulphur recovery and sulphur handling, all demand additional operating and maintenance staff. A favorable sulphur market under certain conditions may justify the processing of sour gas whereby sulphur is either a by-product or a co-product, Five typical cases involving different compositions of sour gas are presented for evaluation. Capital costs, operating problems, and operating costs are presented in detail for full economic evaluation

Jan 1, 1967

By Knut H. Hubert

The GRATE-KILN System plant at Svappavaara, Sweden, was constructed for LKAB by Allis-Chalmers under a turnkey contract and commissioned in 1969. The plant was designed to produce iron ore pellets from magnetite concentrate at 6100 mtpd using imported fuel oil. It represented the state of the art for plants of its type at the time. Fuel rated capacity was attained within one week of start-up. Product quality, power usage, fuel consumption and machine wear were within warranty limits during sustained production thereafter. As operator skills improved and gas handling system reserve capability was utilized, the plant frequently produced acceptable product at up to 115% of design capacity. During the period 1969 to 1976, market demands increased for high-quality pellets while energy costs rose steadily. At the same time, important advances in the design of GRATE-KILN Systems were being made in other plants constructed by Allis-Chalmers.

Jan 1, 1980

By L Usoni

Collectors commonly used in flotation to date fall into two main classes: ionic and nonionic. The use of neutral or oily collectors is generally limited to the flotation of nonpolar minerals onto which they are adsorbed by forces of a physical or 'Van der Waals' type, while ionizable chemical collectors are utilized for all other types of minerals, adsorption in this case involving bonds essentially of a chemical nature. Though chemical adsorption is more selective than physical adsorption, even heteropolar collectors are active towards certain classes of minerals (sulphides for example) rather than towards one individual mineral. Thus, in order to float a given mineral from a mixture of minerals belonging to the same class, modifiers have to be used to render the action of the collector more specific. However, there are often considerable difficulties involved in this procedure and the desired results are not always attained, especially in the case of minerals of complex composition whose surface properties are not sufficiently well known. Hence the importance of seeking out collectors capable of linking selectively with given minerals. Selective linkage is possible if the collector structure incorporates active groups having specific affinity for certain cations characteristic of the mineral surface. The decision to investigate the possibility of utilizing chelate--forming reagents for flotation was based on the premise that phenomena which occur in solution and involve chemical reactions in the strict sense of the meaning and those which occur on the surface are closely correlated (1)

Jan 1, 1971

By Michael J. Miller

In the design of a modem mill, a stockpile storage system for raw and/or semi-processed ore has become almost indispensable. This paper discusses the benefits of such stockpile storage as well as the various types of belt conveyor stockpiling units available. Particular attention is given to large radial stackers since they offer the greatest flexibility. Stacker control systems and accessory equipment are briefly discussed. Various alternative reclaiming arrangements for stockpiles are reviewed and a discussion of the advantages and drawbacks of each arrangement is included.

Jan 1, 1979

By James Giulianelli

Personnel at the Jet Propulsion Laboratory (JPL) are studying the technology and applications of salt-gradient solar ponds (see below) for both electrical and thermal energy generation. The brine extraction and processing site operated by the Kerr-McGee Corporation at Searles Lake, California, offers ideal conditions for economic construction of solar ponds. Furthermore, since rising conventional energy costs adversely affect the economic recovery of brine by the present process, this site was selected for a study on the feasibility of integrating the solution mining of trona (Na2CO3?NaHCO3?2H20) in the lower salt with solar ponds for heating. The major emphasis of this study was to determine whether inexpensive thermal energy available at the brine extraction site would be useful in extracting increased mineral value from the resource. The present operation, which involves the simple extraction of the complex brine and its processing at the adjacent plant, is sometimes referred to as solution mining. Since the concept discussed in this paper involves injecting a heated sodium sulfate brine to dissolve carbonate underground, the proposed scheme is referred to as "enhanced" solution mining. The subject is discussed in greater detail in a recent JPL report. (1)

Jan 1, 1981

By D. R. Tweeton

A modified push-pull field test and a computer model of cation exchange were developed to aid in evaluating cation exchange parameters prior to in situ mining. Reliable determination of these parameters is essential when modeling restoration of groundwater quality. The field test involves a much larger volume and much less disturbance to the ore sample than is feasible with laboratory measurements. This test can be performed in two or three weeks. It is relatively inexpensive, requiring one injection- production well and two or more wells for collecting samples of leach solution. The use of the model in interpreting test results is illustrated with field data from an in situ uranium mine. Much of the research was performed by the University of Texas at Austin, and was partially funded by the Bureau of Mines.

Jan 1, 1986

By J. Kuti

In room and pillar mining a large number of working points are arranged to follow a mining pattern. Geological and roof control problems can be overcome or their effect minimized by varying this pattern. Longwall mining on the other hand, fixes the mining pattern for anyone panel. This aspect of longwall mining leads to constancy, so that a well-conceived organization, ventilation, dust and roof control systems lead to daily repetition and subsequent simplicity of control. All the same, a fixed mining pattern calls for a very careful consideration and selection of design parameters. (Ref. 1.)

Jan 1, 1971

By Wen Tao Liu, Tong Tian, Fu Sheng Niu, Xiu Man Liang

The level of automation employed in flotation production is relatively low. In an actual concentrator, operators use their judgment to adjust the production state based on the visual characteristics of the flotation froth surface. There are shortcomings, such as strong subjectivity and lagging process operation, that easily cause the waste of manpower and material resources. Machine vision technology is introduced to replace human visualization, achieving a quantitative description of the visual characteristics of the froth surface. The state variable parameters are provided for the identification of the flotation conditions.

By Isa Nozari, Asghar Azizi

The extraction of copper from sulfate leaching liquor was investigated using Acorga M5640 commercial extractant in kerosene diluent. The effects of important factors such as the extractant concentration, contact time, liquor pH, and temperature were examined on the separation factor Cu/Fe and the extraction efficiency of copper. The results indicated that nearly 92.32% copper was extracted from the leach liquor at 10% (v/v) Acorga M5640 concentration, 1:1 aqueous/organic phase ratio, 20 min contact time, pH 2.5, and 25 °C temperature. Also, the further increase in the values determined had no positive impact on the extraction of copper. Under these conditions, the separation factor Cu/Fe was obtained about 29.64. The extraction mechanism was studied applying the plot of log(D) – 2 pH against log [extractant] and it proved the association of two moles of Acorga M5640 for the extraction of one mole of copper. McCabe–Thiele diagram was constructed and a single-step extraction process was found to obtain themaximumextraction. Additionally, thermodynamic datawere investigated and the extraction process was endothermic and non-spontaneous at 298 K (ΔH = 27.05 and ΔG = 15.52 kJ mol−1). Moreover, the loaded organic phase was stripped and 80.94% copper was recovered after 20 min using 10% sulfuric acid concentration.

Jul 31, 2020

By Alper Kirmaci, Taghi Sherizadeh, Kutay E. Karadeniz, Dogukan Guner, Samuel Nowak

Injuries and fatalities resulting from roof falls are still a major concern in U.S. coal mines, and many researchers are focused on developing meaningful approaches to minimize this hazard. In the United States, coal mine roofs can vary widely in composition, geometry, and inherent heterogeneity, leading to a wide array of different roof fall failure types. Researchers frequently employ numerical modeling tools to reproduce this physical phenomenon and provide key guides to engineers regarding roof conditions and control as long as the input data and constitutive relations are appropriately selected. Simulating such complexity requires expertise and constitutive models that adequately simulate roof behaviors. However, the currently available constitutive models have shortcomings in capturing some of the roof fall failure types common in underground coal mines, such as guttering. A new constitutive model is developed to address the shortcomings of constitutive models commonly used for coal roof stability analysis. The constitutive model developed in this study combines the anisotropic-elasticity and nonlinear strain-softening responses. In addition, the developed constitutive model can simulate up to three different joint sets implicitly, allowing for use in both continuum and discontinuum settings, and can be used in both Lagrangian finite-volume and distinct element method codes of Itasca. First, the mathematical expressions of the model are provided. Afterward, the validation phase of the developed model that covers comparisons with analytical solutions and those of existing models (e.g., anisotropic elasticity, ubiquitous-joint, and bilinear strain-hardening/softening ubiquitous-joint plasticity) is presented. Finally, a hypothetical coal mine roadway facing high horizontal stress is simulated. The presented model successfully shows three distinct stages of a cutter roof in a shale roof: (1) initiation of shear cracks at the rib– roof intersection, (2) extension of cracks deeper into the roof (i.e., above the roof bolt length horizon), and (3) cantilevered roof. It is demonstrated that the presented constitutive model has the potential to help future researchers in simulating various roof responses.

Jul 1, 2023

By S. N. Gurulaxmi, Veerendra Singh

The abstract discusses the increasing consumption of manganese ores and the need to utilize low-grade ores and rejects. The study focuses on developing a low-cost process using a cupola furnace to recover manganese values from these resources. The process involves smelting ore blends to produce high MnO slag and pig iron. The study investigates various factors to improve iron reduction and separation from MnO-bearing slag. The results show that the process can produce slag with MnO > 35% and Fe(t) < 5% using low-grade Mn ores. The process also achieves Fe reduction between 50 and 70%. The cupola furnace offers advantages like low cost and ease of operation, making it suitable for processing low-grade ores and rejects to produce synthetic MnO-enriched products for various industries.

Apr 1, 2022

By K. D. Luxbacher, E. C. Jong

Perfluoromethylcyclohexane (PMCH), a member of the perfluorocarbon tracer group of compounds, has been shown to be a viable supplement to the widely used tracer gas sulfur hexafluoride (SF6). This viability stems from the fact that PMCH can be used concurrently with SF6 while maintaining adequate chromatographic separation and comparable sensitivity during analysis. However, the release of PMCH in an underground mine ventilation system is challenging due to its physical characteristics. While SF6 exists as a gas at room temperature and pressure and can be accurately released by a variety of means, PMCH exists as a volatile liquid at room temperature and pressure, preventing it from being deployed in a similar manner. One method to release PMCH is to use a permeation plug passive release vessel (PPRV), which allows for the controlled release of the gas. This paper presents the results of a study evaluating various preparation techniques, plug thicknesses and plug materials of an aluminumvessel PMCH release source, so that a source appropriate for the mine scale may be developed.

Jan 1, 2015

By N. O. Lotter

The reliability of a set of flotation results is key to minimizing project risk, either at the commissioning of a concentrator or at the point of implementing an improvement to an existing concentrator operation. High-confidence flotation testing (HCFT) was developed for this purpose and is part of the list of technologies at various scales used by Xstrata Process Support (XPS) in addressing these projects. The methodology is based on two principles: one, to ensure that the ore sample is representative and has been well-blended and subsampled; two, to perform the flotation tests in sufficient numbers of replicates with appropriate quality controls, so as to improve the reproducibility of the test data. Across ten years of research on this methodology at Xstrata Process Support, Sudbury, several improvements to the HCFT method and complementary connections between sampling and quantitative mineralogy have been developed. Two case studies are reviewed. These show the capability of this system in both optimizing an existing concentrator operation and in serving a new mine scenario. Further work to improve the efficiency of this procedure has been identified. Key words: Flotation testing, Flotation

Jan 1, 2010

By Xiaodong Yu, Jinxia Zhang, Fusheng Niu, Hongmei Zhang

The three-dimensional (3D) fractal dimension is an important parameter to analyze the 3D structure and flocculation effect of the hematite flocs. In this work, the 3D fractal dimension of hematite flocs was predicted by establishing the particle swarm optimization (PSO) algorithm optimized with the back propagation (BP) neural network (PSO-BP). The proposed model considers four factors, namely, the flocculant quantity, flocculation time, stirring speed, and temperature, as the input parameters. We normalize the input data during the preprocessing stage. The BP neural network was optimized by using the PSO algorithm for realizing the 3D fractal dimension. The prediction accuracy and effectiveness of the model were evaluated. The experimental results showed that the predictions performed by the proposed PSO-BP neural network were better than that of BP neural network. In addition, the root mean square error (RMSE), mean squared relative error (MSRE), mean absolute error (MAE), and mean absolute relative error (MARE) of the proposed model are lower, compared with the errors of the BP network. Similarly, the measurement coefficient R2 of the proposed model is higher, compared with the BP network. The maximum absolute error of the model is 0.0772, the maximum relative error is 0.02405, and the regression coefficient r is 0.98592. These results showed that the proposed model has a good performance and high prediction accuracy. When verifying the practicability and the effectiveness of the proposed PSO-BP model, the prediction results of 10 groups of hematite flocculation experimental data under different conditions showed that the prediction value of the proposed PSO-BP model was closer to the ground truth as compared to the BP model. Therefore, the proposed model is suitable for predicting the 3D fractal dimension of hematite flocculation.

Oct 3, 2022

By Kenneth N. Han

The effect of anions such as sulfate, chloride, and nitrate on the solubility of rare earth element-bearing phosphates and fluorocarbonates has been examined using relevant thermodynamic data. The study has found that these anions have significant influences on the overall dissolution of rare earth elements (REEs) from various sources in the aqueous media. The thermodynamic calculations in this study have indicated that the speciation of REEs with the anions tends to increase the overall solubility of the REE-bearing minerals. However, in some cases, strong precipitation of REEs with some of these anions causes an adverse effect on the solubility of these elements. It has been found that sulfate ion has the most pronounced effect on the solubility compared to nitrate and chloride, in which the latter two acids exhibited almost identical results. The calculated results have indicated that REE-oxide (hydrated) is the easiest compound to dissolve, followed by carbonate, phosphate, fluoride, sulfate, fluoro-carbonate, and oxalate in that order.

By NEHA PANDEY, V.K. REDDY KALLAM, SUNIL KUMAR TRIPATHY, ARIJIT BISWAS

This work discusses the sulfur dioxide (SO2) leaching of low-grade ferruginous manganese ores to selectively recover manganese (Mn) as manganese sulfate (MnSO4), followed by electrowinning of the purified MnSO4 to produce electrolytic manganese dioxide (EMD). The effects of the leaching process parameters on Mn recovery were studied, and the leaching duration and SO2 flow rate were found to have significant effects. Under the optimum conditions derived for grade 1 ore (with total Mn content of approximately 17.16 percent), the specific SO2 requirement (SSR) — that is, the SO2 flow rate per gram of Mn in the leach slurry — was calculated to be 0.014 L/min. At the SO2 flow rate calculated using SSR for grade 2 ore (with total Mn content of approximately 26.29 percent), a Mn recovery rate of 94 percent was realized. Electrowinning of the purified MnSO4 generated after leaching resulted in EMD with 88.01 percent purity and a γ structure.

Sep 1, 2022

By Rudolph K. Hoagberg

Silica sands, primarily in coarse size ranges, are used to prop open fissures or voids created in the bedrock by hydraulic fracturing. This procedure increases the flow of gas or oil or other fluids through the bedrock. The sands used must meet various specifications relating to their physical and chemical characteristics; these characteristics are in turn related to the geologic provenance of the sand deposit. The Jordan Sandstone, a Cambrian formation which is exposed in Minnesota and Wisconsin, meets the specifications of a proppant sand by virtue of its depositional history and its sedimentary properties.

Jan 1, 1980