Search Documents

By Frank E. Dalton, Forrest C. Neil

INTRODUCTION The Tunnel and Reservoir Plan (TARP) (Figure 1) was adopted in 1972 as the most cost-effective way to bring Chicago area waterways up to Federal and State water quality standards. TARP will significantly reduce pollution of these waterways and provide flood relief for Chicago and 53 adjacent suburban communities. These communities, covering an area of 971 sq km (375 sq miles), are at present served by combined sewers, which carry both raw sewage and stormwater. Because porous ground surfaces have been covered over in recent years by buildings, streets, and parking lots, stormwater runoff into sewers frequently exceeds the capacity of the sewers. When this happens, sewers back-up into hundreds of thousands of basements, and the overflows on the combined sewers discharge rainwater mixed with raw sewage directly into the area's waterways at 645 overflow points. The result is severe pollution of the waterways and flooding in 53 communities. During particularly heavy rains, overloaded rivers have to be relieved by opening the locks and allowing the polluted waterways to flow into Lake Michigan, the region's water source. Goals of TARP 1. PREVENT BACKFLOWS INTO LAKE MICHIGAN. 2. ELIMINATE WATERWAY POLLUTION CAUSED BY COMBINED SEWER OVERFLOWS. 3. PROVIDE AN OUTLET FOR FLOOD WATERS.

Jan 1, 1981

By M. R. Stokes

Over the recent years there has been an increase in the application of retreat mining on longwall faces as mine operators strive for ever greater productivity. The purpose of this paper in then to review current practice as a starting point and then move forward to discuss the future geometry's that a longwall face may take. Single and double production zone three roadway faces are assessed. All possible configurations of three roadway faces are defined. Unsuitable configurations are rejected after analysis of broad ventilation issues. The remaining configurations are then assessed on an operational basis, this includes: limits on retreat synchronisation, structure of centre gate, floor bulging and equipment installation. The remaining viable configurations are then further assessed on ventilation issues, this includes: provision for gas control/gas fringe, face climate and balancing of face flows. Possible face climate is assessed using numerical simulation of the various configurations, the predicted dry/wet bulb temperature and predicted levels of heat stress indices are given and discussed in detail, along with face flow balancing. The necessary conditions required for the successful operation of a double production zone three roadway face system are formulated, together with conclusions as to the possible level of application.

Jan 1, 1997

By N. L. Wesis

General History The first jaw crusher in the US was patented about 1830, but the Blake crusher that has maintained a substantial advantage over other types was invented in 1858 by Eli Whitney Blake. For going on 150 years the jaw crusher has been an invaluable machine; even today, when gyratory crushers have assumed most of the burden of crushing large tonnages of large rock and ore, the jaw crusher has a firm place in the mining industry. It is interesting that soon after the invention of the Philetius Gates gyratory crusher in 1881, a contest between the first No. 2 Gates and Blake jaw crushers of equal gape showed the gyratory to be 3.2 times as fast. This foretold a day not far in the future when the jaw crusher would not be adequate on the largest jobs. In his Textbook of Ore Dressing (1909) R. H. Richards recom¬mended that the word breaker be used for all machines breaking to relatively large sizes (say to 5 in. or greater), and crusher be used for finer work. Even in the 1968 US Bureau of Mines dictionary of mining terms the work breaker is defined by Richards in this context. However, in modern US usage it is nearly limited to coal breaking. Over the years the jaw crusher has been developed in a variety of forms but it appears today in these three general forms: (I) Blake type, (2) Dodge type, and (3) single toggle (or overhead eccentric) type. All of these crushers have a fixed jaw and a moving jaw, between which the coarse rock fragments are intermittently caught and crushed. The three types are differentiated by the manner in which the movable jaw is moved in relation to the fixed. Types The Blake-type crusher is shown in cross section in Fig. 1. The simplicity and strength that have made it first among jaw crushers are evident. The movable jaw is suspended from a cross-shaft at its upper end, this shaft being carried in bearings on the sides of the frame. The actuating mechanism consists of an eccentric shaft, also supported in frame-mounted bearings, which imparts through a pit¬ man and a pair of toggles a reciprocating motion to the bottom of the swing jaw, the return movement being effected by several spring¬loaded rods. The whole is built into a box frame with the crushing chamber at one end. As in all jaw crushers, the eccentric shaft is equipped with a heavy flywheel that maintains an even speed through¬out each stroke. The Dodge-type crusher illustrated in Fig. 2 is simple, mechani¬cally. Its movable jaw, being pivoted below the discharge opening, has minimum movement at crusher discharge and maximum at crusher feed. Because the choke point coincides with the point of least motion, these crushers are of relatively low capacity, and the rapid action in the feed area gives the machine the advantages of large reduction ratio and closely sized product. Thus, it fits well into low-capacity operations like sample reduction. Besides low capacity, its principal disadvantages are tendency to pack and make fines. The single-toggle or overhead-eccentric type of jaw crusher (see Fig. 3) has gained in usage, starting as a modification of the Dodge idea in that the greatest movement of the movable jaw occurs at the top, and being gradually improved and strengthened to its position today where it covers just as wide a field of application as the Blake type from the standpoint of feed opening. The motion of the movable jaw is the result of the circular motion of the eccentric shaft at the top of the swing jaw combined with the rocking action imparted to the bottom by the inclined toggle plate. Because of light weight and mechanical simplicity, it is economical in small mills and portable plants where the rock is not as tough and abrasive as to punish the machine with excessive impact from shocks, or excessive wear result¬ing from the pronounced vertical component of motion.

Jan 1, 1985

By P. Malozemoff

Discussion by P. Malozemoff I have no objection to using mathematics in the value appraisal of properties. The factor that is not emphasized in the paper is that very few important properties have a lifetime that reflects the initial ore reserves of the property divided by the rate of production adopted. In the majority of cases, major properties mine out several times the initial reserves. How much more will be mined out is not known, and only exceptionally gifted geologists can predict that additional reserves will be found. There is the further factor of metals price, which, over the long term, is not predictable. Another factor vitiating making calculations on initially established ore reserves is the speculative nature of exploration success. In my judgment, the life of a property, in addition to an established ore reserve, should include ample time for exploration to find additional reserves. The likelihood of additional reserves is based on the geological promise of the general area where the mine is established. This is especially important because of various risk factors associated with small orebodies, the economic life of which is about five to seven years. In underground mines, it is not economic to develop reserves beyond a certain depth, so the life of initially established reserves must be limited. In these cases, it is especially important to have a good geological understanding of the orebody and its continuity. To accommodate these concepts and present proof of economic soundness for a mining enterprise, a mathematical analysis should yield a life long enough to allow exploration and the development of additional reserves that would ensure a longer mine life and a more profitable result.

Jan 1, 1994

By T. Bednarski, T. McCallum

"Physical impurity transfer in solvent extraction (SX) has a significant impact on operating costs, electrowinning (EW) performance, and cathode quality. Some operations use a wash stage to limit impurity transfer by diluting the entrained pregnant leach solution (PLS) to prevent direct transfer to EW. Wash stage operating conditions vary impacting impurity transfer. A number of factors impact dilution efficiency including mixer continuity, wash aqueous acidity, and organic quality. The impact of these variables on dilution efficiency was studied and compared to current industry practice. INTRODUCTION With the exception of iron, impurity transfer in copper SX is due to PLS carryover in the loaded organic via aqueous entrainment and crud movement. The quantity of impurity transfer is influenced by many variables including operating set points, organic quality, and settler housekeeping. Crud management and treatment is a common practice aimed at minimizing transfer of impurities to EW. Crud is a complex solid-stabilized emulsion of aqueous and organic[9]. As such, it contains a large aqueous component and the associated impurities (from the PLS). A common practice is to remove interfacial crud to prevent movement. Additionally, mixer continuity can be altered to enable compaction and improve the efficiency of interfacial pumping[10]. Understanding the factors impacting aqueous entrainment and optimizing the available controls should be a key focus for any operation. Aqueous entrainment in the loaded organic can be impacted by: • Mixer continuity • Mixer organic/aqueous (O/A) ratio • Mixer speed and impeller type • Organic and aqueous depths • Specific settler flow • Use of settler internals (picket fences, coalescing packs) • Organic quality • Design and operation of loaded organic tanks Conventional thought is to run the E1 mixer in aqueous continuity to reduce aqueous entrainment. Generally, O/A ratios close to 1:1 result in improved metallurgical and physical performance. Mixer speeds should be chosen to achieve acceptable stage efficiencies while minimizing over-mixing. Organic depths can be increased in the E1 stage to increase retention time and minimize aqueous entrainment. Settler internals can also be used, but require maintenance to maintain effectiveness. The quality of the plant organic inventory will impact physical performance. Poor organic quality can lead to higher phase disengagement times increasing impurity transfer to the electrolyte. Additionally, the design and operation of the loaded organic tank can impact impurity transfer[8]. Despite the variables that can be used to reduce aqueous entrainment and crud movement, impurity transfer is still an issue in some operations. For these operations with high PLS impurity concentrations, a wash stage may be beneficial to manage impurity transfer. Understanding factors impacting wash stage performance is important to optimize performance and limit impurity transfer."

Jan 1, 2016

By Dennis N. Poffenroth

One concern of the Mine Safety and Health Administration is the structural integrity of steel wire ropes used on mine personnel hoists and elevators. Failure of such ropes has resulted in loss of life and property. Although thorough and regular visual examinations are performed, hoist ropes may still fail from undetected internal wear, corrosion, and broken wires. To complement visual examinations, nondestructive rope inspection techniques have been developed to determine deterioration and removal criteria. The techniques use electromagnetic and permanent-magnet test instruments designed by a Canadian firm. This paper describes the operating principles, field and laboratory testing of these nondestructive testing instruments, and discusses the feasibility of using this type of testing as a supplement to visual examination and destructive tests.

Jan 1, 1982

By André Vervoort

At the 2017 ICGCM-conference in Morgantown, WV, a case study was presented with measurements of the upward surface movements or uplift after the closure of two neighboring coal mines (Winterslag and Zwartberg, Belgium). One was closed in the sixties, and the other closed in 1988. The study was based on satellite data (Radar-interferometry or InSAR). The analyses showed both a significant variation of uplift values above the mined area and the surrounding zones, and a variation of the uplift rate as a function of time. In other words, the phenomenon of uplift is complex. At that time, it also was clear that more research was needed to better understand this phenomenon, e.g., an identification of the various mechanisms that are relevant for the process of uplift and the quantification of the various impacts. A systematic analysis of all relevant parameters resulted in a framework that forms the basis for the analytical calculations of uplift values. These calculations show that the main impact is due to changes in the hydrostatic pressure. However, the expansion of the softest parts, i.e., the collapsed or goaf material, is not only important, but the expansion of the (stiffer) non-collapsed strata layers due to a change in pore pressure also must be integrated into the model. For the case study, the partial flooding of the underground after closure of the mine that was abandoned in the sixties is integrated into the model. Larger stiffness values also are applied for this mine, in comparison to the values of the more recently closed mine. Overall, a very good correlation is observed between the InSAR-measurements and the calculated values along a north-south transect.

Mill #4 processes mildly refractory ore from Carlin Trend deposits. Diagnostic analysis of plant operating data was used to generate a mathematical model containing the key parameters influencing the gold recovery. The model was used to direct modifications to plant operating practice. The cyanide dosing strategy was changed to reduce preg-rob gold masses and cut reagent consumption A finer grind was achieved without capital investment. The density in CIL was lowered, and tighter control was exercised over plant throughput. These changes resulted in a recovery increase of at least 2%, worth $111,000/month at $300/oz, and concomitant reagent cost savings of $55,000/month.

Jan 1, 1999

By T. Murt, C. Oñate

In recent years, environmental considerations have played a prominent role in underground construction projects. The management and disposal of the muck produced by an EPB TBM is an important aspect of this topic. Soil conditioners with higher biodegradability and lower eco-toxicity have been specifically developed to comply with strict regulations in several countries around the world, with the goal of reducing the environmental impact of tunneling on soil, water, and living organisms. This paper highlights innovative sustainable soil conditioners and how they differ from traditional products. Additionally, environmental considerations for TBM projects around the world and in North America will be examined.

Dec 1, 2022

By Gary P. Thomason

We have all heard a great deal about how various projects were financed or certain companies were successful in obtaining a bank loan. There are many more projects and companies who fail to get the money they need. At least a portion of these failures, and a large percentage of the frustrations connected with even the successful financings, are a result of not understanding the process of obtaining money. Recent years have seen a proliferation of sources available to finance minerals operations, but let me assure you that these represent only a minor portion of the minerals financing market. The fundamental source of borrowed money to almost all minerals related companies remains the banks. Therefore, understanding the "Loan Approval Process" can easily mean the difference between getting the money or not. In the following pages I hope to provide some insight into what I define as the loan approval process. Having pre-offered my definition, I intend to delineate the various stages of the process and the planning and information I believe should be contained in each. My ultimate goal is to help you think like a banker and, in so doing, stay on top of the process so that you can successfully obtain the funding necessary for your projects.

Jan 1, 1983

By A. Newman, A. Brickey

Although some of the prevalence of openpit production scheduling software can be explained by the predominance of openpit mining throughout the world, other factors have led to a lag in corresponding underground software. We explain mathematically why underground production scheduling is more difficult than its openpit counterpart and provide directions for research in the underground scheduling arena.

Jan 1, 2014

By G. A. Gunderson

Since our time is very limited, I would like to relate to you as best as I can a few important areas that I think may be helpful. 1.) The Real Difference between Dense Phase and Dilute Phase Pneumatic Conveying: Within the many variations of so called Dense Phase conveying, it is often difficult to determine to what degree a system is Dense Phase or if, in fact, it is a Dense Phase system at all. A system that appears and is generally known to be Dense Phase can under certain operating conditions perform as a Dilute Phase system. If, for instance, a high pressure system, which is generally a Dense Phase system, operates at 60 PSIG, say 4 atmospheres, utilizes enough air volume, the conveying velocity will easily exceed the normal design velocity of a typical Dilute Phase system. Now, on the other hand, a low pressure system which we will term a Dilute Phase system, operating at 15 PSIG; say 1 atmosphere, can convey a given product at well below the saltation velocity, like a Dense Phase system.

Jan 1, 1977

By J. S. Hu

FTIR spectroscopy has been used for the characterization of adsorbed oleate at the fluorite surface. It has been found that modest changes in the adsorption density at high temperature and high oxygen potential do not provide a satisfactory explanation for the significant increase in the hydrophobic character of the system under similar conditions. Rather, FTIR spectroscopic measurements suggest that chemical interaction between adsorbed oleyl groups occurs at high temperature and/or oxygen potential and accounts for the increased hydrophobicity. Specifically, the intensity of the =CH bond of the adsorbed oleate diminishes at high temperature and/or high oxygen potential. Such a phenomenon was not observed in control tests with the calcium oleate soap. For extensive reaction at the fluorite surface, the presence of a new surface species has been identified. These results indicate that the fluorite surface catalyzes an oxidation and/or polymerization reaction between adsorbed oleyl groups which results in a more hydrophobic structure at the fluorite surface.

Jan 1, 1986

By D. Elroi

This paper addresses the sharing of 2D and 3D data between GIS and mine planning software. Two-dimensional (2D) data, and now three-dimensional (3D) data as well, can be formatted such that both types of software can use, exchange, and display the same datasets. This increases the ability to share data between such groups as environmental, exploration, and mine planning. It overcomes shortcomings of mine planning software in areas of open database connectivity, spatial analysis, and data input and output. It also helps to overcome shortcomings of GIS software in the areas of geologic modeling, three-dimensional interpolation, and visualization.

Jan 1, 1998

"INTRODUCTION While the United States coal mining uses prescriptive regulation under the Title 30 Code of Federal Regulation enforced by the Mine Safety and Health Administration (MSHA), Australia uses a risk based approach. Australian regulation is individual to each state. In Queensland, Australia this risk based approach to address principal hazards is underwritten by the Queensland Coal Mining Safety and Health Act of 1999 and the Coal Mining Safety and Health Regulation of 2001. Each Queensland Mine is required to have an overarching Health Safety and Environment Management System, of which Safety Management Plans are an element. “Safety Management plans (SMP’s) are intended to formalise the process by which mines address principal hazards and other related matters to ensure the safety of mine personnel.”7 THE QUEENSLAND CONTEXT In Queensland, the basic elements of a coal mine’s safety and health management system must provide for risk identification and assessment, hazard analysis, hazard management and control, and the reporting and recording of relevant safety and health information and data.5 (Part 2 Division 1 Section 6(a-d)) The initial guidance for writing Safety Management Plans comes from the Approved Standard for Mine Safety Management Plans and Guidance Note QGN09- Reviewing the Effectiveness of Safety and Health Management Systems. The Guidance Note and Approved Standard are supplemental to the Act and Regulation, and put in place to provide more clarity around the topic. The definitions in this section come from the Approved Standard and are included to provide context for those who may not be familiar with Australian or Queensland law and regulation. A hazard is defined as a source of potential harm or a situation with a potential to cause loss, while a principal hazard is a hazard with a potential to cause multiple fatalities. A risk is the chance of something happening that will have an impact upon objectives which is measured in terms of consequences and likelihoods. It is important to be able to make the distinction between a hazard and a risk. For instance, a lion is a hazard, while the risk associated with a lion is getting eaten. As defined by the Queensland Approved Standard for Mine Safety Management Plans, a Safety Management Plan (SMP) requires a systematic definition of all the actions necessary to ensure that mining operations are carried out safely. A SMP includes, but is not limited to organisational structures, planning, activities, responsibilities, practices, risk identification, audits and reviews.7 The goal of a SMP management plans is to mitigate the risks to bring them to an As Low As Reasonably Achievable (ALARA) level."

Jan 1, 2016

By Lukas Walder, Roland Arnold, Raphael Zuber, Richard Gradnik

This paper presents the construction of the ventilation shaft for the single-tube, doublelane Kramer tunnel. The project is located in the Federal State of Bavaria, Germany. This road tunnel, which has been under construction since December 2019, is the key component of the western bypass of the town of Garmisch-Partenkirchen. Once completed, it will relieve the town’s central district from enormous volumes of traffic. The contractor is the joint venture named ARGE Kramertunnel consisting of BeMo Tunnelling and Subterra. The whole project will be completed and handed over to the project owner, Staatliches Bauamt Weilheim, in 2023. The opening of the entire bypass section including the tunnel to traffic is planned for 2024. The tunnel, with a total length of 3,609 m (2.24 miles) and an estimated cost of EUR 178 million incl. VAT (US-Dollar 201 million), is designed as a single-tube, double-lane structure with one traffic lane for each direction of travel. The safety issue that exists for singletube tunnels is solved by a parallel escape tunnel passable for vehicles. For tunnel ventilation, an intermediate shaft has been designed with a depth of approximately 90 m (295 feet) and an inner diameter of 4.5 m (14.8 feet). All tunnels and ducts are excavated according to the principles of the New Austrian Tunnelling Method (NATM). The geological and hydrogeological conditions, the change in the profile (from round to square geometry), and also the shaft being located at a high elevation presented a demanding technical and logistical challenge. The site arrangement with the pit bank was located in a cut, the slopes of which had to be stabilized with shotcrete and soil nails. This excavation was carried out from the fall of 2020 to the beginning of 2021 because construction operations had to be completed outside the nesting period of protected birds.

Jun 13, 2023

By G. R. O?Neil

The justification for a "ligand- selective' approach to fine mineral beneficiation via flocculation is established initially. Special emphasis is placed upon the need to identify non-selective, interfering and complicating adsorption effects. Specific strategies directed towards the design and synthesis of complementary selective flocculants are detailed using a number of different polymers and chelating agents as examples. In this regard, the affinity of polymer-bound ligands for metallic cations, ligand concentration, possible modes of attachment, the application of spaced-out ligands and other considerations in the preparation of selective flocculants are highlighted.

Jan 1, 1983

By R. J. Haydel

The Highland Uranium Operations of Exxon Company, U.S.A. is a large uranium mining and processing complex situated in the Powder River Basin of East-central Wyoming. Surface mining and chemical processing of a large relatively low-grade ore body began in late 1972. An underground mine was later developed and began production in November of 1977. Figure 1 shows the location of our operations. During the planning stages of the project, it was recognized that hiring and retaining quality employees would be a significant problem. Other operations in similarly isolated locations were experiencing high turnover rates and were forced to employ inexperienced and poorly trained operators. In an attempt to attract employees, many of the companies provided mobile home or bunk- house facilities, but these costly peripheral ventures did not prove to be noticeably successful.

Jan 1, 1979

By A. Newman, A. Brickey

A pesar de que parte del predominio de software de programación de producción a cielo abierto se puede explicar por la preponderancia de la minería a cielo abierto en todo el mundo, hay otros factores que han dado lugar a un retraso en el software subterráneo correspondiente. Explicamos por qué matemáticamente la programación de la producción subterránea es más difícil que su contraparte a cielo abierto y daremos pautas para la investigación en el campo de la programación subterránea.

Jan 1, 2014

By G. E. Tooker

This paper (1) presents new data on the use of horizontal curves to optimize the alignment of belt conveyors. The operating concept of a horizontal curve is simple. As an element of the belt passes through the curve, it is motivated to drift toward the center of the curve by unbalanced tension forces in the belt. This lateral drift is resisted by the forces of friction and gravity, which in turn can be stated as a function of drift. Resisting forces, as a function of drift, are stated in terms of variables such as the amount of load on the belt, and parameters such as the trough angle, tilt angle, and super elevation angle, and number of rolls in the idler. The trick is to determine that the belt will drift to a position of equilibrium within predictable limits, without physically constraining the edge of the belt. In practice this prediction is not easy to make without the aid of a computer. The motivating force is easy to calculate, but its value is continually changing throughout the angle subtended by the curve arc. The resisting forces are constant throughout the curve for a given drift and load condition, but the calculations are very complex. Data in this paper will assist the conveyor designer in making preliminary calculations for horizontal curves. Presented is the equation for calculating the motivating force, and a family of curves that show the resisting force as a function of lateral drift for some commonly encountered conveyor design criteria.

Jan 1, 1985