Search Documents

By K. W. Deter

The gold ores in the Jerritt Canyon district have been recognized as refractory since they were first encountered by FMC geologists in 1976. Upon obtaining managing rights as joint venture partner, Freeport McMoRan Inc. developed an operating plan featuring carbon-in-leach gold recovery techniques for the oxide portion of the ores and a patented sulphide oxidation step followed by chlorination for treating the organic carbon constituents of the refractory ores prior to CIL gold recovery. The plant was successfully started up in 1981 with the first gold poured on July 4, 1981. Initial plant throughput was designed to be 2495 MTPD (2750 STPD) total through the dual processing trains.

Jan 1, 1991

By A. M. Gaudin

The recent study by R. M. Hays(l) prompted the study summarized in this paper. In his Interesting paper, Mr. Hays shows fine results to be attainable by a relatively complex flowsheet on a semi-taconite, a manifestly difficult ore to treat. We obtained a semi -taconite from Minnesota, and treated this sample by wet magnetic separation alone. The device in which the separation was accomplished is the standard pilot-plant, laboratory separator in use at Magnetic Engineering Associates' laboratory (MEA) in Cambridge, Massachusetts. It consists of a cylindrical space which can be magnetized by turning on the magnet of the separator. In this cylindrical space, there is a canister which provides the special configuration of the magnetic field and magnetic field gradients that MEA considers to be required. The ore pulp is made to flow through the canister while the current is on. A portion of the pulp is retained in the canister, and the rest is evolved as a non-magnetic fraction. The laboratory device is cyclic, but it accurately predicts the results obtainable by an Industrial unit of either cyclic or continuous type (moving matrix). The ore tested was 99.5°%o -325 mesh, and approximately 75% -500 mesh. The concentrate from this ore was, therefore, eminently suitable for pelletizing. In passing the ore through the magnet, we had the choice of repeatedly passing the concentrate from the first step through the operation, or of repeatedly passing the non-magnetics. In our experiments, the first method was clearly superior from the stand¬point of the cleanliness of concentrate. Of the many tests which we have made, we think that we have to retain two which

Jan 1, 1971

By D. Erik Spiller

Mineral processing technologies are being used in the environmental arena for remediation and secondary recovery. Comminution and/or scrubbing for liberation, coupled with separation of the liberated particles, is known as soil washing. Other metallurgical unit operations have found application in remediation and recycling: size classification, gravity concentration, flotation, magnetic and electrostatic separation, eddy current separation, and liquid/solid separation. This paper presents specific examples of the use of these technologies to clean up contaminated soils and plant residues, and to recycle valuable materials from waste streams.

Jan 1, 1993

By M. R. Shahan, W. R. Reed, P. Zhang, J. P. Rider

Roof bolter operators may be exposed to high respirable dust concentrations on continuous miner sections with blowing face ventilation when bolting is performed downwind of the continuous miner. One solution to reduce the high respirable dust concentrations is to use a canopy air curtain (CAC) to deliver clean air from a filtered blower fan directly to the bolter operators under the canopies. The influence of CAC installation in the airflow and dust dispersion around the location of the roof bolter operator can be evaluated by using computational fluid dynamics (CFD). This study, performed by the National Institute for Occupational Safety and Health (NIOSH), considers two scenarios: (1) a roof bolting machine in the center of the entry for installation of the fifth row of bolts from the face, and (2) a roof bolting machine positioned close to the face for the installation of the last row of bolts. In both scenarios, the bolting machine is placed in an environment which contains 6.0 mg/m3 of respirable dust and is ventilated by a blowing curtain with 3,000 cfm (1.42 m3/s) of air. This environment is used to simulate the roof bolter machine operating downstream of a continuous mining machine. Two operation positions are simulated at the same bolting location: dual drill heads in the inward position for two inside bolts; and dual drill heads in the outward position for two outside bolts. The influence of the CAC on airflows and dust dispersion is evaluated with the CAC operating at 250 cfm (0.12 m3/s). INTRODUCTION Roof bolting machines are used to drill bolt holes into the roof of an underground mine at specified patterns and to install roof bolts to secure the roof from falling. At times, the roof bolting machine is also used to install rib bolts; however, only the roof bolting operation was considered in this simulation. Though the roof bolting operation drastically improved the safety of miners from roof falls, some roof bolter operators are experiencing health problems associated with respirable dust. Based on recent statistics [1], following a low point in the late 1990s where the prevalence of coal workers’ pneumoconiosis (CWP) in miners with 25 years or more tenure was approximately 5%, CWP now exceeds 10% for miners with 25 years or more of tenure. In central Appalachia (Kentucky, Virginia, West Virginia), 20.6% of long-tenured miners have CWP and 4.5% have progressive massive fibrosis, the most severe form of CWP. CWP, also known as black lung, is an occupational respiratory disease that has no cure and can ultimately be fatal. The only way to prevent the incidence of black lung is to eliminate miners’ exposure to respirable coal mine dust. Current U.S. regulations require that the overall respirable dust concentration to be 1.5 mg/m3 or less for a full-shift sampling if respirable quartz is not present; otherwise, the standard is 10 divided by the percent quartz (not to exceed the 1.5 mg/m3 respirable dust standard) [2, 3].

Jan 1, 2019

By Claudia Castillo, Katja Freitag, Jan Cilliers, Diana Drinkwater, Robert Seitz

The talent gap in mining is not a new challenge. Mining companies continue to seek innovative ways to attract, develop and retain talent, and younger workers are looking for opportunities to develop their professional careers. Training provides a key value proposition for both employees and employers as it helps build a talent pipeline while offering opportunities for learning and growth and value creation. In 2020, Metcelerate launched its 20-month program for early career mineral processing engineers. The program helps develop critical technical skills in the workplace and is a tool to identify motivated engineers and change culture within teams. Learners cap their skills development by executing a technical investigation. This generates immediate value—a win-win outcome for learner and company.

Feb 1, 2025

By T. Hayes

Track-type tractors remain one of the most cost-efficient stripping tools available to coal miners. Whether they are "sweetening up" a dragline operation with pre-benching or serving as the primary stripping tool, dozers can play an important role in driving down mining costs. This paper reviews the application zone of track-type tractors. In addition, it provides tips on site set-up, equipping of tractors, and machine operation which the audience can take home and apply.

Jan 1, 1996

By D. W. Struhsacker

Mineral exploration has evolved into a sophisticated science which uses powerful scientific tools to make mineral discoveries. In addition to their usefulness in performing mineral exploration, these scientific tools can assist the exploration geologist in assessing environmental conditions at exploration sites. During exploration, environmental data acquisition should focus on data collection efforts which can be easily integrated into exploration activities, and should provide information needed for pre-feasibility and preliminary engineering design studies. Environmental studies performed during exploration should also include an environmental liabilities audit and a fatal flaw analysis to assess whether there are any unresolvable environmental or regulatory issues affecting the project. Performing extensive environmental baseline studies during exploration and project evaluation is neither necessary nor recommended. This paper describes opportunities to integrate environmental data collection with mineral exploration activities. This paper also examines how political and communication issues can affect the outcome of permitting efforts, and recommends a strategy to improve the industry's ability to respond to political challenges and to communicate with the public. This strategy integrates technical and political issues, and implements programs to convince the public of the mining industry's technological achievements and its commitment to resource stewardship and environmental protection.

Jan 1, 1994

By J. Driscoll

After 30 years of success, Newmont Gold Company has temporarily ceased production from the original Carlin Pit. In late 1993, the Carlin East Decline was driven and an extensive underground exploration program was started. Today, Newmont Gold produces refractory ore from the Carlin East underground at the rate of 700 t/d (770 stpd) for an annual production of over 100,000 ounces. Over 70 underground miners enjoy the estimated 6-year mine life at Carlin East. About 70% of the ore at Carlin East is mined by mechanized longhole stoping with delayed cemented backfill. The remaining ore is mined by underhand drift and cemented fill methods.

Jan 1, 1997

By V. A. Scovazzo

The analytical pillar design procedure employing the Wilson equation is based on the site-specific material strength of the floor, pillar, and roof rock. Stable pillars so designed will sometimes be larger than those designed using empirical methods thus providing more stability or at other times smaller than empirically designed pillars thus conserving natural resources. Presented here is a detailed procedure for the analytical design of soft rock pillars using the Wilson Equation. An example of this procedure is presented that uses data from a mine in the Owl Seam in Southern Appalachia. These Owl Seam pillars are now in use and are performing as expected. Also addressed is an assessment of the Dr. Scovazzo?s analytically designed pillars based on pillar performance data gathered by Dr. Mark in the Southern Appalachian Coal Field.

Jan 1, 2010

By A Pettersson

LKAB owns and operates two of the largest underground mines in the world in Northern Sweden. In Malmberget, with a production capacity of about 30,000 t/day of iron ore, the current main 815 m haulage level is rapidly approaching the end of Its life and plans are being made for its replacement on the 1000 m level. Due to the separation of the orebodies, trucks have been chosen for transporting the ore from the orepasses to the crushers. The trucks currently in use have a capacity of 120 tons. To increase the efficiency of the loaded haul, the new main level will have a favorable slope from the drawpoint locations to the crushers. From the new level the crushed ore will be transported by conveyor to the 815 m level for hoisting to the surface. The paper discusses the planned mining and transportation system.

Jan 1, 1998

By K. F. Unrug

Fractures of sedimentary rocks in the vicinity of the outcrop are commonly encountered around the world. Mine highwalls and numerous highway cuts give excellent views for detailed study of surface fractures. This paper gives an explanation of the origin of fractures as well as characterization of the distribution and extent of joint system with reference to lithologic composition of the rocks. Practical implications of the joint system affecting mine operations are described. Among the subjects discussed are: discontinuous deformation as an effect of surface subsidence, stability of mine portals and near outcrop underground operations, and stability of highwalls, when using highwall miners and strip operations. Some design procedures are recommended that can minimize the problems encountered in mining areas with intense joint systems.

Jan 1, 1994

By Y. J. Wang

The definitions of system pressure loss (mine head) and system resistance, which are traditionally associated with single-fan net- works, are applied to multiple-fan ventilation networks. The system characteristics -- relations among air power, pressure loss, air quantity and resistance -- are analyzed by introducing the concept of subsystems. These subsystems are associated with the fans located in a cutset of the network. For a multiple-fan network, the resistances for the subsystems and total system are dependent on the quantity ratios of the subsystems. In general the pressure loss of a subsystem or a total system does not vary as the square of the corresponding air quantity. If the quantity ratios of subsystems are all held constant, then the resistances become constant and the pressure losses are predictable from the quantities employing the "square law." The system resistance has a minimum value under the natural- splitting flow pattern. Being independent of the value of system quantity, the minimum system resistance provides a basis for comparing the different networks.

Jan 1, 1983

By Hubert Erik Sherer

Determination of the best time to replace an aging unit of equipment is a recurring problem which is common to essentially all surface and underground mining operations. Virtually all mining equipment is subject to wear and the resulting deterioration that increases with equipment life. This mechanical deterioration results in lower availability and, thus, decreasing, production. Due to decreasing production and increasing repair costs, there is an optimum age at which the replacement of a given equipment unit with a new unit will result in the lowest cost per unit of production for the equipment operation in question (Figure 1). Determination of this optimum replacement age is further complicated by factors such as: possible overhaul alternatives, fleet replacement and expansion alternatives, remaining life of the mine, and technological improvements in the potential replacement or differences in the production capacities of these replacements. Determination of the optimum time to replace an equipment unit becomes more critical each successive year due to the rising capital costs of new equipment versus maintaining old equipment. An incorrect choice of the replacement age for an equipment unit can result in excessive costs to the mining operation. If a unit is replaced too early, the capital cost of the unit is not fully utilized; conversely, replacing a unit too late results in excessive maintenance costs and low production. The economic life of a piece of equipment is the equipment age that results in the lowest total discounted cost per unit of production for that piece of equipment, not considering the cost of future replacements. The economic life of a piece of equipment is usually shorter than the physical life, the maximum age at which a machine is capable of doing useful work. The optimum replacement age for a piece of mining equipment may vary from the economic life of that equipment due to the remaining life of the mine, fleet considerations, costs associated with potential replacement machines, and capital rationing constraints. For example, the equipment life of the current machine that may result in the lowest cost per unit of production might be 10 years; however, when the timing of the future replacement costs are entered into the calculation, a different life for the current machine might result in the lowest total cost per unit produced for the remaining life of the mine.

Jan 1, 1982

By Richmond Bennett

Airborne geochemistry became a reality with the advent of a high-sensitivity airborne gamma ray spectrometer with large volume NaI (TI) crystal detectors. Small variations in the concentration of potassium (as K40), thorium (as T1208) and uranium (as B1214) along the flight lines can be determined by measuring the gamma radiation with a sensitive airborne spectrometer. Small volume crystal spectrometers are useful only for detection of major surface uranium (Bi214) variations, but the large crystal volume system is an airborne geochemical exploration method capable of locating hydrothermal mineral deposits. Radioactivity as a guide to ore has been discussed in the literature by Damon (1950), Gross (1952) and others. The theoretical basis is that potassium, thorium, and uranium are concentrated in late stage solutions during magmatic crystallization. Thorium and uranium are concentrated in late stage liquids because their large atomic radius and high ionic charge prevent them from entering into the crystal lattice of common rock-forming minerals (Rankama and Sahama, 1950). Potassium, which has a large ionic radius and small charge, also can be concentrated in the high water content late stage fluids (Heier and Adams, 1964). A large proportion of uranium and thorium in rocks occurs around grain boundaries of the essential rock-forming minerals (Hurley, 1950). Uranium and thorium substitute for zirconium in zircon, a comparatively early forming mineral. However, most of the thorium and uranium is concentrated in residuals where they can be fractionated and incorporated into allanite, monazite, xenotime, and other minerals.

Jan 1, 1970

By Duluth Engineers' Club, Engineers' Club of Northern Minnesota

"There are three distinct producing iron ranges in Minnesota, the Vermilion, Mesabi and Cuyuna. In trend the Vermilion and Mesabi are approximately parallel (E.N.E. and W.S.W.) and about fifteen to twenty miles apart. The Vermilion lies farthest north, near the. Canadian boundary. It is from seventy-five to eighty miles due north of Duluth. The length of its productive part is about twenty miles.The Mesabi Range is from fifty to seventy-five miles north and northwest of Duluth. Its length along the strike is about 110 miles, and the length of its present productive area about eighty miles. The Cuyuna range lies southwest of Duluth nearly ninety miles, and is the last of the Lake Superior iron ranges to be developed. The relative positions of the ranges are shown on an accompanying map. The Mesabi Range is by far the largest producer and contains the largest ore reserves of the three. The Cuyuna is next in quantity of proven ore, and in production since 1916, while the Vermilion is first in average quality of ore.On the west, both Vermilion and Mesabi ranges disappear beneath heavy glacial drift; and on the east, extend into Canada, the so-called Gunflint range near the international boundary being an eastward continuation of the Mesabi formation. This latter range is of no economic importance, however, at present. The exploration and development of the Cuyuna range has proved up a considerable tonnage of manganiferous iron ore, besides ordinary merchantable iron ore."

Jan 1, 1920

By S. J. Page

The personal dust monitor (PDM) is a combined tapered element oscillating microbalance (TEOM) respirable dust monitor and cap lamp, configured to have dimensions and weight similar to those of a lead-acid miner’s cap lamp battery. The Higgins-Dewell (HD) cyclone design operated at 2.2 L min-1 airflow has previously been reported to have low bias relative to the International Organization for Standardization (ISO) convention. Previous reports have described the PDM as meeting the NIOSH Accuracy Criterion. In order to avoid certain analysis anomalies encountered during these evaluations, a different method of establishing the PDM relative standard deviation was employed. Re-analysis of laboratory data for both the early prototype and precommercial PDMs indicates that the PDM still meets the NIOSH accuracy criterion, and that the precommercial PDMs are more accurate than previously reported.

Jan 1, 2011

By W. L. Hollinshead

For more effective and cost saving production in tunnels, the machinery used on construction sites will be equipped with guidance systems combined with working procedure management systems. This paper describes sensors for these systems and various system configurations. A project is described which uses a computerized guidance system on an underground mining machine for guidance and profile control.

Jan 1, 1999

By Patricia Pride, Kurt Bettger, Jack Raymer

"INTRODUCTION The Jefferson Barracks Tunnel is in the final stages of design and is expected to go out to bid in the summer of 2016. The project is located in south St. Louis County along the west bank of the Mississippi River, about 13 km downstream of the St. Louis Gateway Arch. The project consists of a deep sanitary sewer tunnel, a deep pump station and several intakes. The intakes will divert sanitary flows into the tunnel and the tunnel will convey the flows by gravity to the Lemay No. 3 Pump Station, which will pump them up into the Lemay Waste Water Treatment Plant. The tunnel is about 5.4 km long and will be lined with 84-inch (2.1 m) fiberglass pipe. It drops at a gradient of 0.1 percent from south to north and will be bored through strong limestone using a hard-rock tunnel boring machine (TBM). The diameter of the TBM is anticipated to be about 3.4 m. The Owner’s original concept was for a relatively shallow tunnel so as to minimize construction and pumping costs. The preferred alignment ran close to the river, next to the existing force main, which was to be abandoned. Keeping the tunnel close to the force main would reduce the amount of shallow sewer work needed to connect the existing feeder sewers to the new tunnel. Several geotechnical investigations were performed, with shallowly focused geophysics and the borings all going exactly down the conceptual tunnel depth. Limestone bluffs run along the Missouri side of the river. These bluffs are pockmarked by sinkholes and riddled with karst. Large, well-known caves occur both north and south of the alignment. Karst features, including deep crevices and possible caves, were found in those early geotechnical investigations. Many of these features extended well below the level of the Mississippi River and would have been encountered by the tunnel. If a large crevice or cave were encountered, then the inflow of mud and water into the tunnel could have been large and possibly uncontrollable. Something had to be done to mitigate this situation. Pre-excavation grouting was considered, but the program would have been huge and extremely expensive. Using a closed-face TBM with bolted and gasketed lining was also considered, but that too was both risky and extremely expensive. The Owner could have abandoned the tunnel altogether and built a new force main, but that would have brought a whole new set of problems and was undesirable to the Owner. The last option was to move the tunnel away from the karst."

Jan 1, 2016

By William A. Faust

At Gold Fields' Chimney Creek Mine, major reviews of the reclamation and closure plans are done concurrently with the annual mine planning required for budget preparation. This review includes identifying and scheduling reclamation work that can be done within the next few years and development of associated costs. Longer term mine, leach pad and waste dump development are examined to take advantage of any design changes that can reduce ongoing reclamation or closure requirements and reduce costs. The success and cost effectiveness of past efforts are continually evaluated to determine the best methods for reclamation.

Jan 1, 1992

By W. K. Summers

During the past few years monitoring systems have been installed to measure the effects of environmental changes on the ground-water resource. The design of a monitoring system depends upon the designer's perception of how the environmental factors merge with his perception of the ground-water flow system. The validity and representativeness of measurements made during a monitoring program depend upon the validicy of the designer's perceptions and concepts. To optimize the design of a ground- water monitoring program the designer should make preliminary measurements to confirm his assumptions.

Jan 1, 1985