Search Documents

By J. A. Finch, B. J. Huls

Accurate level detection is required to make full use of level in optimizing control strategies for flotation columns. Techniques based on pressure and electrical conductivity are compared. Pressure and conductivity profiles give good agreement on level. Level calculated from single and multiple pressure values became more accurate using, in order, one, two and three sensor locations. The level estimate remained in error, however, because, unlike the collection zone, froth zone bulk density varies with height. A conductivity probe continually updating the conductance profile is a practical method of obtaining an accurate level.

Jan 1, 1990

By S. J. Schatzel, K. M. Ajayi, Z. Khademian

The integrity of unconventional shale gas well casings positioned in the abutment pillar of a longwall mine could be jeopardized by longwall-induced deformations. Under such scenarios, the surrounding fracture networks could provide pathways for gas flow into the mine creating safety concerns. To provide recommendations for developing guidelines that ensure a safe co-existence of longwall mining and unconventional shale gas production, this study evaluates the impact of parameters that could affect potential shale gas flow into the mine in the event of a casing breach using a discrete fracture network (DFN) model. These parameters are evaluated using a conceptualized DFN realization that is representative of the fractured zone in the overburden, and the range of parameter variations are within values validated with field measurements. The results show that a decrease in fracture aperture (potentially due to longwall-induced stress in the likely vicinity of the breach location) reduces the potential gas flow to the mine by a significantly higher proportion. A 50% decrease in the aperture of the fracture that directly transports the gas from the casing breach location reduces the gas flow to the mine by over 70%. Similarly, changes in the fracture water saturation level significantly affect the gas flow. In all cases, the potential gas flow to the mine is higher if the casing breach occurs at an increased gas well pressure. These findings provide critical information regarding the impact of each of the parameters associated with gas flow in the event of a shale gas casing breach near a longwall mine and could help towards the development of guidelines to ensure a safe coexistence of both industries.

Mar 2, 2022

By Osvaldo A. Bascur

Most mining and metallurgical plants have developed predictive maintenance policies based on statistical analysis and special techniques, like vibration analysis, oil and lube analysis for critical equipment. Process control strategies have also been installed in several metallurgical sites. These control strategies require instrumentation maintenance from local personnel. The availability of real time and process history to identify the most critical part of the processing system from mechanical integrity is a must for global plant optimization. Specialized performance control monitoring algorithms are required to justify their existence and contribution to the bottom line. Emerging technologies are combining these techniques into a single total plant system. Tools are required to assist in troubleshooting and adapting these process control instruments and strategies. The key is the plant equipment and process control availability and utilization rather than just maintenance.

Jan 1, 1997

By PAITIP THIRAVETYAN, KANJANA KUDPENG

The aim of this study was to investigate the influence of amino acids (glycine, aspartic acid, glutamic acid, lysine and tryptophan) and organic acids (citric, malic, tartaric, fumaric, oxalic, succinic and ascorbic acid) on gold extraction from silicate ore. Use of amino acids to extract gold was preferred compared with organic acids due to the presence of carboxylic group and amine groups in amino acids. Among the assessed amino acids, aspartic acid and glutamic acid had higher capacities to extract gold due to their structures, which lacked aromatic rings and long side chains. Organic acids could also extract gold. In particular, oxalic and succinic acids had the greatest capacity to extract gold versus the other tested organic acids. Moreover, aspartic acid had a greater capacity to extract gold from ores than the same concentration of succinic acid. We confirmed the aspartic acid and succinic acid functional groups by Fourier transform infrared spectroscopy. The findings revealed that aspartic acid had a greater capacity to extract gold than succinic acid due to the presence of both amine and carboxylic groups (succinic acid contained only a carboxylic group). The optimal gold:aspartic acid molar ratio was 1:6 and low concentrations of aspartic acid extracted 35–42%of gold from silicate ore within 15 days. This can be used as an alternative to traditional methods for extracting gold from ore; it is non-toxic to human health and environmentally friendly.

Aug 10, 2021

By T. N. Moore, E. M. De Souza

J. Dasher Regarding the March 1991 ME technical paper by De Souza and Moore: For more than a decade since my February 1981 article on how to use modern metric, which SME-AIME had decided to do, I have monthly pointed out metric errors to the editors. In part, I do this because there has been no action to allow editors to fix figures and tables or to allow them to require authors to do so. The latest resulting atrocity provokes this discussion of vibrating drill handle units being stated in decibels. Reply by T. Moore We have read the discussion of our paper by Mr. Dasher. Our reaction is one of surprise and incredulity. It would seem that Mr. Dasher takes exception to the use of the decibel scale to present vibration acceleration data, and the use of hertz as the unit for frequency. The basis for his objection to the decibel appears to be that it has no dimensions (which somehow invalidates its use), that it is "non-metric" and, finally, that it is parochial (of limited or narrow scope). His objection to the use of the term hertz is not stated, but we will assume that it stands condemned as "non-metric" and parochial. Obviously we disagree with Mr. Dasher's views and will now outline our reasons. Although the decibel scale originates from transmission line theory and telephone engineering, it is also at present widely used, not only in the fields of electronic engineering and acoustics, but also in the area of vibration. The original definition of the decibel (dB) was based on power ratios: dB = 10 log 10(W/W0) where Wo is a reference power. However, as the power measured across a given impedance is related to the square of the force acting upon this impedance, Z, a more commonly used definition is: [2 dB = 10 logF /Z) = 20 log F/F 10\ F0 2 /Z(0)] where F and F0 are the r.m.s. values of the forces. Now, if the measurements are related to one and the same impedance, the decibel notation in the form of 20log10(X/Xo) may be used as a convenient relative magnitude scale for a variety of quantities. Thus, X may, for instance, be an r.m.s. displacement, velocity or acceleration. It is only required that XD always be a reference quantity of the same type as X. That is, when X represents an acceleration, then X0 represents a reference acceleration. This is the formulation used in our paper. This was not an arbitrary choice on our behalf but reflects standard practice as specified in the International Standard ISO 5349-1986(E) Mechanical Vibration - Guidelines for the Measurement and the Assessment of Human Despite the metric prefix, the decibel is a parochial expression of (l) the logarithmic ratio of the loudness of a sound to what is normally audible or (2) the logarithmic ratio of two power signals in radio or electronics. A decibel is not a unit, much less an SI, unit and has nothing whatsoever to do with the acceleration of drill handles. Stating that m/s2 (acceleration) is decibels is without reason. Whoever reviewed this material should not have allowed publication of figures of dB and H.[ ] Exposure to Hand-Transmitted Vibration. This was clearly stated in the "measurement protocol" section of our paper. This quantity is then referred to as the acceleration level and is expressed in dB. We may have inadvertently caused some confusion when we simply used the term acceleration to refer to acceleration level on our diagrams. At the time, we felt the use of dB or m/s2 would make the context clear to the reader. For any confusion this decision may have engendered, we apologize. Since the decibel expresses the ratio of two like quantities, it certainly has no dimensions. It is, however, common practice to treat "decibel" as a unit as, for example, in the sentence, "The acceleration level measured at the operator's hand was 160 dB." The expression of measured quantities in dimensionless form is not inherently unacceptable. In fact, in many areas of engineering it is standard practice (consider the use of Reynolds Number, Nusselt Number, etc.). The fact that the decibel is a dimensionless quantity makes the question of whether it is a SI unit nonsensical. However, it is valid to insist that the dimensional quantities used to obtain the decibel values be expressed in SI units. A careful reading of our paper will make it clear that the measured acceleration was, in fact, expressed in units of m/s2 as was the reference acceleration (l x 10-6 m/S2). These are the accepted derived SI units for acceleration. See, for example, the standard ASTM E380-89a Standard Practice for Use of the International System of Units (SI) (The Modernized Metric System). Concerning Mr. Dasher's implication that hertz (Hz) is an unacceptable unit of measure for frequency, we would again refer him to the standard ASTM E380-89a. Here, he will find (section 2.4.2) that hertz is an accepted "special name" for the derived SI units-1. This is in keeping with numerous other international standards including ISO 5349-1986(E) to which we referred in our paper. In conclusion, we agree with Mr. Dasher on the desirability of expressing measurements in modern SI units. But we would remind him that the standards that define the use of these units, and the accepted means of presenting measured data, are in a continual state of refinement. It is, therefore, incumbent upon him to keep abreast of these changes if he wishes to constructively critique the work of others.[ ]

Jan 1, 1992

By D. C. McDonald, P. R. Whincup, H. Duke

Due to grade, overburden depth and stability and the presence of groundwater it was considered impractical to recover gold contained in unconsolidated palaeochannel sediments by conventional mining, dredging or borehole mining techniques. A series of field experiments was conducted to determine the feasibility of recovery of gold by in situ leaching from sediments located at a depth of about 80 metres. The test wellfield site and plant are described together with field test procedures, results and wellfield rehabilitation procedures. Choice of sodium cyanide as leachant and laboratory testing are discussed in relation to groundwater and sediment chemistry and problems encountered in field tests.

Jan 1, 1989

By J. Douglas

The past year has been a strange one for the fertilizer industry of the world and the United States. Listening to news stories, you would think the sky is falling on the world's agriculture and probably conclude that we should have had an exceptionally poor fertilizer season. In some respects, we did. Prices were low, profits were low, and in some cases nonexistent, but volume was good. We heard much in the press about the farmers' credit crunch. The truth of the matter is that only 6.6 percent of the U.S. farmers have debt-equity ratios of 70 percent or more, and a large percentage of our farmers have absolutely no debt but operate entirely on their own cash assets.

Jan 1, 1985

By E. M. Frizzell

An ongoing research program at the Spokane Research Center of the U.S. Bureau of Mines is directed toward investigating drilling parameters (thrust, torque, penetration rate, and drill revolutions) during the drilling of roof bolt holes. A system that measures these drilling parameters calculates the specific energy of drilling, and determines drill bit position has been developed by the Bureau and mounted on a roof bolting/drilling machine, through the use of a microcomputer, critical drilling parameters can be immediately interpreted and analyzed. This makes it possible to inform the operator of hazardous roof conditions. Initial results of this program are presented here.

Jan 1, 1990

By H. Akgun, J. J. K. Daemen

Design of plugs for abandonment of boreholes and shafts may be governed by the bond strength between the plug and host rock. Presented in this paper are the results of push-out tests on two types of expansive cement grout plugs emplaced in rock salt. The average interface shear strengths range from 2 to 12 MPa. Peak shear stresses (assuming an elastic stress distribution along the interface) are up to eight times higher. Dissolution along the interface may be enhanced by clay inclusions in the salt and appears to reduce bond strengths. Application of the results to the design of plugs for larger openings (e.g., shafts, drifts, or boreholes) is discussed.

Jan 1, 1995

By M. G. Ayat, B. C. Scott

Coal degradation is the breakage of coal particles to finer sizes due to the continuous forces of attrition and gravity to which coal is subjected during mining, handling, and preparation. The objective of this paper is to determine the extent of degradation that a coal slurry experiences when transported through pumps and pipelines. The examination of degradation results for a number of different coal slurries have indicated that the extent of breakage is dependent on the physical properties of coal and the time span of circulation. These results have also indicated that certain size fractions of coal are more susceptible to breakage than others.

Jan 1, 1987

By Lee W. Abramson, James E. Crawley

Caltrans is studying alignments for a 160-kilometer-long high speed ground transportation system from Los Angeles to Bakersfield across the Tehachapi Mountains. This link is needed to connect southern California with San Francisco by a short passenger rail service. None presently exists. The system will require tunnels and viaducts along the route with sections crossing two major active fault zones. High speed ground transportation technologies are being evaluated for achieving rail speeds of between 200 and 480 kilometers per hour. This paper presents the technical requirements for tunnels along the alternative routes being considered for the project.

Jan 1, 1995

By W. A. McKinney

In conventional dump leaching of porphyry mine strip wastes, many years are required to extract up to 20 percent of the copper from the contained sulfide minerals. Furthermore, none of the molybdenum, gold, or silver in the strip wastes is recovered by current leaching practices. Because mineralization occurs predominately along fracture planes, breaking of the rock during mining operations liberates and concentrates some of the metal values in the fines. Research shows that upgraded fines can be screened from mine wastes and froth floated for early recovery of copper, molybdenum, gold, and silver. For example, screening a dump sample assaying 0.35 percent copper as chalcopyrite removed about 20 percent of the copper as minus 1/4-inch material that analyzed 0.6 percent copper. About 35 percent of the molybdenum and 20 percent of the gold and silver also reported in the fines. Crushing the mine dump sample to minus 3 inch before screening increased the distribution of copper and molybdenum in the minus 1/4-inch screen fraction to 28 and 50 percent, respectively. Similar results were obtained by screening fines from two other large samples of mine waste dump materials. Flotation studies established that the enriched minus 1/4-inch fines from the three dump samples could be effectively concentrated. Comparative testing revealed that the combination of froth flotation of fines and acid-ferric sulfate leaching of the coarser fraction enabled doubling the recovery of copper over direct leaching of the samples. In addition, significant amounts of molybdenum, gold, arid silver were recovered by flotation.

Jan 1, 1970

By M. D. Ross

Complex combinations of technical, economical, safety and environmental factors are causing mining engineers everywhere to review their operations. Naturally, some of the traditional methods still have a large role to play because they are, in certain circumstances still adequate and are well understood. But, as circumstances change, a new approach is required. The combination of technical and economical reasons for introducing Long- wall mining in some seams in the United States is associated with strata control. Other reasons include simplifications and improvement of ventilation, reduced coal dust, more output from each unit and crew, increased percentage of recovery from each area of the coal deposit, and reduction of rock dusting. The innovations which transformed Longwall mining from a cyclic to a continuous mining system were the armored conveyor and power loading machines, but the crucial breakthrough for application to high production was the development of the powered roof support, which at once gave the system the advantages of mastery of strata control, increased rate of advance, significant reduction of manpower, and increased safety.

Jan 1, 1974

By M. Measures, W. A. Napier, C. Pomroy, J. M. Jardine

INTRODUCTION In most uranium mines the concentration of uranium in the ore is low enough that inhalation of dust does not present a radiological problem. Conversely in the mills there is a potential inhalation hazard from inhaled uranium in concentrated form, namely "yellowcake" and other compounds intermediate between the ore and the final product of the mill. It was generally assumed that the solubility of yellowcake placed it in the category of Class D materials. This plus the fact that the uranium is non-enriched led health physicists to assume that the potential health hazards were a result of the uranium's chemical properties rather than its radiological properties. Bioassay programs have thus been limited to routine urine sampling at a weekly or monthly frequency. In most cases when a high reading was obtained, subsequent sampling within one or two days showed a rapid return to low levels, therefore tending to confirm the class D nature of the material. Two developments over the last few years have however suggested that modifications to this simple bioassay program may be necessary and practical. Firstly, a number of studies on the solubility of uranium mill products, from ore to yellow cake, in simulated lung fluid (Eidson A.F., Mewhinney J.A., 1980) have shown that some of the material is not class D, but class W or even Y. This raised the possibility that, while the urine levels rapidly decreased, indicating rapid excretion of the class D component, the W and Y components remained in the lung. Thus an unsuspected lung burden could have been accumulated. The second development, the ready availability of [in vivo] counting facilities with which to make direct measurements of uranium lung burdens, offered a means of confirming the hypothesis of unsuspected lung burdens. A study was therefore initiated to correlate lung burdens with urinary excretion. METHOD A total of 79 subjects from 3 uranium mills participated in the study. They were brought to the Ottawa laboratories of the Radiation Protection Bureau in groups of 4 or 6, over a period of several months. In Ottawa, [in vivo] thorax measurements were performed, and a urine sample collected. Each subject also brought with him a urine sample that had been collected the previous day. All samples were split, for analysis by both R.P.B. and the mill laboratory. [Concentrations of Uranium Dust] Results obtained by mills A, B and C for concentrations of uranium in air at various locations are given in table 1. Samples taken at mill B were obtained using continuous sampling with a midget impinger over a six hour period. Samples taken at mills A and C were 5-minute gravimetric samples. [Subject Selection] The subjects were selected to represent a wide range of work history in terms of both length of employment and type and location of job, as shown in table 2.

Jan 1, 1981

By Vitaly T. Borisovich

Mining economics courses have been taught in Europe for more than two centuries and in the United States for most of this century. They are the mineral industry's version of engineering economics offered by industrial engineering departments. In the 1930s, mineral economics first appeared in American mining schools. This subject goes beyond the deposit and the mine. It examines the economic aspects of mineral resources in general and the individual mineral industries in particular. In 1947, the first degrees in mineral economics were granted in the United States. There are mining and geological engineers who specialize in mining economics. But it has rarely become a separate degree program. Rather, in this country and several others, a graduate student in a mining department or school will include economics in his course work. Then the person writes a thesis or dissertation on a mining economics topic. One exception is found in Moscow at the Department of Geoeconomics of the Moscow Geological and Prospecting Institute (MGPI). To place this program in perspective, some background is needed on education in the Soviet Union.

Jan 1, 1991

By Norm Greenwald

The Environmental Protection Agency ("EPA") has been attempting to develop a federal regulatory program for mine waste under Subtitle D of the Resource Conservation and Recovery Act since 1986. Recent regulatory and legislative events are now bringing this goal closer to reality. This paper discusses the mining industry's perspective on a number of the issues currently being addressed at EPA's Policy Dialogue Committee and in Congressionally-sponsored negotiating sessions.

Jan 1, 1992

By Michel L. Van Sint Jan, Gabriel Fernandez-Delgado, Edward J. Cording, James W. Mahar

INTRODUCTION Shotcrete behavior observed in subway tunnel construction in the U. S. has been primarily in blocky or blocky and seamy rock in which rock loads develop from the self weight of individual rock blocks that tend to loosen from the wall and roof of the opening. Such conditions can be classed as loosening ground, in contrast to squeezing ground in which high pressures are generated on the tunnel lining with time as the ground creeps under the natural ground stresses. In the philosophy often associated with the New Austrian Tunneling method, emphasis is placed on the use of shotcrete and other support elements in squeezing, highly stressed ground, in which the support system is designed to allow controlled movements so that high lining stresses do not develop. In contrast to these conditions, the concern in loosening ground is to provide support soon enough to minimize loosen-

Jan 1, 1979

By Richard B. Stein

This paper will present an overview of several hydrometallurgical processes which can be used for sea-nodule metal recovery and some simplified economics. Before going any further, here are some of the basic figures from which the economics were developed. The first is to establish a representative composition for a typical nodule feed (Slide 1). This set of chemical analysis figures can be taken as typical for a deep Pacific nodule feed and shows manganese at 30%, copper at 1.1%, cobalt at 0.2%, nickel at 13% and iron at 10% for the metals of economic interest1.

Jan 1, 1982

By Ian McFeat-Smith, Odd G. Askilsrud

Introduction Given the mountainous nature of the local igneous terrain, hard rock tunnelling plays an important role in the development of Hong Kong's infrastructure. In 1990, tenderers for two tunnel projects were encouraged to consider using hard rock TBMs, the territories' first. As a result the 7.5km long, 3.56m diameter Tolo Effluent Tunnel and the 5.3km long, 4.8m diameter Hong Kong Electric Cable Tunnel were excavated by hard rock TBMs. The successful completion of both projects in 1992 should make the TBM method an attractive construction alternative for planned, upcoming projects in Hong Kong. Tunnelling Conditions Tunnelling solutions are frequently adopted in Hong Kong due to the intensity of development, lack of flat landscape and proximity of mountainous terrain to the main centers of population. This is carried out primarily in granites or granitic-type rocks which surround Victoria harbour, and to a lesser extent in the outlying volcanic rocks which include extremely hard tuffs and lavas. Tunnelling will generally take place in granitic rocks, normally about 100-250 MPa in strength, and with an average joint spacing of 0.3m and a quartz content of 30-

Jan 1, 1993

By Dan Mackie

Since the production prototype continuous vat leaching pilot plant was installed at Ariel Resources in Costa Rica in 1995, the test results and lessons learned have been invaluable in plotting the future of this method. Vigorous test programs in base and precious metals as well as design developments for studies have shown the advantages, economically, technically, and environmentally that favor this method over current practices in heap leaching and stirred tank leaching. Much larger individual vats have been developed with throughputs as high as 5000 t/d with larger vats envisaged, and there has been a trend towards using vats with ground ore. Five projects are slated to begin detailed engineering this year, three in precious metals and two in copper. Of particular interest to future producers is the ability to deposit d,y, detoxified tailings at a fraction of the cost of conventional methods. Proprieta,y work is ongoing which promises to eliminate the need for tailings dams when using other methods of processing such as flotation. This is of particular importance in light of dam failures around the world in recent years.

Jan 1, 2000