Search Documents

By J. R. Wynnyckyj, R. Marr

Continuous measurement based on radiation pyrometry has often met with difficulties whose causes have been obscure. In this paper the experience gained with on-line pyrometry in utility and Kraft recovery boilers in the range 800-l400oC will be reported. It is shown that the inherent problems are best resolved by using a spectral pyrometer not sensitive to gas radiation. The radiation from the suspended particles thus provides the signal. It is further shown that the principle cause of difficulties is signal calibration drift caused by heat fluxes originating from surrounding surfaces and reflected by the particles to the pyrometer. Several examples are given how such problems may be resolved using process information and/or additional measurements, fed to and processed by and on-line microcomputer.

Jan 1, 1989

By J. M. Brupbacher, D. C. Nagle

"The XD TM * approach to producing metal matrix composites employs an in-situ precipitation technique for the formation of the reinforcement directly in the matrix of interest. Key features include: thermodynamically stable reinforcement; clean particle/matrix interfaces, single-crystal reinforcement; size, chemistry, and shape control; uniform distribution; compatibility with conventional ingot techniques; and grain refinement.Using XD~ technology it is possible to simultaneously introduce a number of different reinforcements in a given matrix, thus allowing for designing the microstructure to meet a specific material need. Thus, XD1l'1 technology is a very useful technique for achieving ""designer"" or ""engineered"" microstructures. XD TM technology has been applied to a number of systems including AI, NiAI, TiAI and Cu. Materials property and processing benefits will be discussed."

Jan 1, 1988

By Suk J. Im, I. S. Min, Daesoo Kim

UFP are defined by atoms or their clusters having diameter in the range of l0Å-0.l.um. Due to a ratio of very large surface area to volume, they have peculiar properties such as extra high surface energy. Recently UFP deposition technique may find its new applications to various areas such as conductive/resistive film formation. In this method, gas flow with UFP jet through the nozzle which is considered to be a free molecular flow is maintained at a very high speed (~100m/s). Using this technique, mixture film of Fe and Ni, and Ag/ Ag-Alloy etc. were obtained, and their mechanical and electro-magnetic properties were determined. The experimental results are pending. The test results and discussion will be presented in the main paper.

Jan 1, 1988

By Henrique Hesse, Rosana de Cassia de Souza Schneider, Wolmar Alípio Severo Filho, Ezequiel Bavaresco, Rodrigo Klamt, Luciano Roni Silva Lara, Luciano Dornelles

Alkyd resins are used in surface treatment. They are product of the glycerolysis followed by polymerization. In the present work it was studied methods of alkyd resin production from crude glycerol compared with resin produced with pure glycerol. This glycerol corresponds to 10% of the final products in the biodiesel production. The crude glycerol was partially purified with neutralization, flotation and adsorption. The experiments were accomplished with temperature control, inert atmosphere and with several quantities of the substrate. For the products characterization physic-chemistry methods, infrared spectroscopy and hydrogen nuclear magnetic resonance were used. According to the observed results, the resins obtained with crude glycerol have presented similar properties of the classic alkyd resin produced with pure glycerol. The exploitation of the crude glycerol reduces the stages and costs of the process.

Jan 1, 2008

Aluminum has experienced significant growth in automotive applications over the last decade as a result of its properties and performance attributes. Looking to the future, the opportunities for continued growth in powertrain and suspension applications plus light weighting of body structures offer the potential for considerable further growth. This represents a growing "energy bank" of aluminum that will become available for recycling at the end of these vehicles' lives. Today, around 90% of the aluminum is recovered and recycled from scrapped vehicles because of its high value relative to other materials. The future growth offers opportunity for new technology and practices, to maximize scrap quality and recycling application. This paper will review the demand for these new technologies and practices and will discuss industry activities being pursued in this area.

Jan 1, 2000

By Tian Li

Simple compartmental models of a laboratory batch gibbsite precipitator were used to investigate the influence of the number of compartments, the local shear rate and solids distribution on the crystal size distribution (CSD) under the conditions where aggregation is the dominant mechanism. In the current work, a power law relationship was assumed between the local agglomeration and shear rate. The simulation results showed that both the local shear rate and solids distribution have significant effect on the CSD responses, and the interchanging flows has a lesser impact with its influence strongly depending on the former two factors. Overall, the results reveal that in an aggregation controlled precipitation system, the influence of each of the factors on the CSD depends on the local hydrodynamic conditions in the precipitator, as well as their interactions.

Jan 1, 2003

By Iris Filzwieser

The secondary copper producer, Montanwerke Brixlegg AG (Austria), produces 73 000 tonnes of cathodic copper per year using ISA tankhouse technology. METTOP GmbH (Austria) evaluated the different anode qualities from the plant with relation to the current efficiency and specific energy consumption. Parameters including the chemical and physical anode quality, current and current density distribution at each cathode, voltage, and distance between each cathode and anode were examined. In addition, the temperature, chemical analysis, and conductivity of the electrolyte was determined for each investigated cell, as well as the anode weight, anode scrap, cathode sheet, and short circuits. Metallographic analysis was also performed on selected dendrites. The investigations resulted in specific improvements in the tankhouse process including the level of anode impurities, and future projects are planned for further tankhouse optimization.

Jan 1, 2006

By B. Nebreda, I. Vegas, R. Vigil, O. Rodríguez, M. I. Sánchez de Rojas, M. Frías, R. García, J. Urreta

"This paper shows the possibility of reutilize paper sludge waste as supplementary cementing material for the cement manufacture. This industrial waste consists essentially of a mixture of organic matter (30%) and inorganic compound, such as calcite and clay minerals. The raw paper sludge does not present pozzolanic properties, but once calcined at 650ºC during 2 hours, exhibits high pozzolanic activity, similar to silica fume at 28 days, as a consequence of the transformation of kaolinite into metakaolinite. Calcined paper sludge was used as partial Portland cement replacements of 0, 5, 10 and 20%. Enhancement in compressive strength was appreciably obtained for 10 and 20% substitution levels from 7 days on. Furthermore, calcined paper sludge slightly reduces the initial and final setting times of cement paste. Introduction Natural pozzolanic materials have been ordinary used in different aspects of construction, mainly for their influence on the microstructure and durability of blended cement matrixes [1, 2]. Due to the regulations of environmental protection, many researches are focusing on the possibility of obtaining pozzolanic materials from industrial wastes and not from natural materials (ceramic wastes, silica fume (SF), activated clays) [3–5]. One of the most used pozzolanic products is the metakaolin (MK) obtained from the activation of natural clay (kaolinite). The positive effect that MK has on blended cement performances [6,7] and also the influence that curing temperature and matrix nature have on the reaction kinetics and stability of hydrated phases produced during the pozzolanic reaction, according to the studies carried out by Frías et al. [8,9] are well known. However, there is a worldwide trend towards the use of recycled products in cement industry. In this line, some authors have reported an alternative way of obtaining MK from waste paper sludge [10-14]. The raw paper sludge (PS), once calcined under controlled conditions (700-800ºC), produces a MK with pozzolanic properties [15-20]. The present research is part of an experimental study about alternative source for MK from the Spanish paper recycling industry and its use as supplementary cementing material. This contribution pays special attention to the option of reducing activation temperature below 700ºC. This fact has a positive effect in reducing the energy consumption, as well as in reducing environmental impacts associated with decarbonation of calcite. The chemical and mineralogical characteristics of raw paper sludge and derived calcined product are described. In addition, the influence and behavior on blended cement properties (setting times and mechanical properties) are also discussed."

Jan 1, 2008

By Jie Li, Liangxing Jiang, Yexiang Liu, Junfeng Gui, Bo Hong, Xiaocong Zhong, Yanqing Lai, Xiaoying Yu

"Pb-based alloys with Pr and Ag were prepared in vacuum electromagnetic induction furnace. The tensile strength, corrosion rate and anodic potential in sulfate solution were measured, and the experimental data were analyzed according to the metallographic phases of alloys, the micromorphology and composition of their oxide films. The results show that, with the addition of Pr, the ultimate tensile strength and corrosion rate of pure lead were increased, and the anodic potential decreased. The extra addition of Ag can improve the properties of alloy further. Comparing with Pb-Ag0.8 alloy which is widely used in zinc electrowinning industry, the ultimate tensile strength of Pb-Ag0.6-Pr2.0 alloy was increased by 31.75%, the anodic potential under 50mA/cm2 was decreased by 30m V.IntroductionIn zinc electrowinning industry, the Pb-Ag (0.5-1.0 wt.%, 0.8wt.% normally) anode is widely used as an insoluble anode['l. It can meet the basic requirements, but still has several problems such as high oxygen evolution over-potential (about 860mV), unsatisfactory corrosion resistance, lead contamination of the cathode product and high consumption of Ag etc.In order to reduce the energy consumption, enhance the corrosion resistance, improve the product quality and reduce the consumption of Ag (or even dispense with it), much research has been done, mainly focusing on Pb-based alloy anodes and Ti-based coated anodes. Detailed investigations have already been carried out on binary alloys (Pb-Ca and Pb-Co), ternary alloys (Pb-Ag-Ca, Pb-Ag-Ti, Pb-Ag-Sn, Pb-Sr-Sn, and Pb-Ca-Sn) and quaternary alloys (Pb-Ca-Sr-Ag, Pb-Ca-Ce-Ag, and Pb-Ag-Sn-Co)[Z-4l, Although these anodes can effectively reduce the consumption of Ag, only the Pb-Co and Pb-Ag-Sn-Co anodes perform well with regard to reducing the anodic potential. However, their complicated manufacturing conditions restrict further commercial use.Besides its application in nonferrous metal electro-winning industry, Pb-based alloy is also used as grid alloy for lead-acid battery, serving as active materials supporter and current collector. In order to enhance the corrosion resistance and deep-cycling performance, reduce the impedance of the corrosion film, the addition of appropriate rare earth elements into anodic grid alloys has become a research focus. Studies proved that RE can enhance the mechanical strength of grids, inhibit the formation of anodic Pb(II) film on the surface of grids and then reduce the impedance of the film[ 10-12l."

Jan 1, 2013

By Jiu-ju Cai, Wen-chao Liu, Fei Liu

"The material flow of urban eco-industrial system includes linear flow, recycling flow, branching flow, converging flow, etc., which consequently lead to the system complexity. Comparing the urban eco-industrial system to ecosystem, it can be concluded that this complexity is caused by the system adaptability. In the system, the interaction and adaptability between the agents themselves and between the agents and the environment stimulates the changes of material-flow mode, which lead to the evolvement from traditional industry to the eco-industry. Focusing on the evaluation of this evolvement process, two material-flow models are established in this paper, one of which is for the system itself and the other for the agents in system. The latter model is applied to analyze the interrelationships among mass, energy and pollutant flow in the iron and steel industry, and to make the direction clear to improve the resource and energy efficiency and decrease the environmental load.1 IntroductionIndustrial system is a subsystem of urban system, and they are interconnected and interrelated through material flow. The industrial development causes the urbanization. But the traditional industrial mode, characterized by high consumption, high pollution and low efficiency, also causes the “urban problems”, and leads to the reduction of resources carrying capacity and the increase of environmental load. Nowadays a lot of researches focus on how to realize the sustainable development of industries and cities. Thus comes the urban eco-industrial system guided by industrial ecology.Regarded as a Complex Adaptive System (CAS), the urban eco-industrial system evolves for quite a long time. According to Holland’s description on CAS, CAS consists of adaptive agents, which interact with the environment and other agents, learn and accumulate experiences, and accordingly change their own structures and motion modes. In this way, the evolution of the whole macro system is improved [1]. The evolution from traditional industrial system to urban eco-industrial system is mainly reflected in the variety of internal material flows which include not only linear flows but also recycling flows. Therefore, to construct models which clearly analyze industrial metabolism, is of great importance to evaluate industrial system evolution.The article is organized as follows: Section 2 describes the urban eco-industrial system. Section 3 presents the system-oriented metabolic analysis model and the agent-oriented one, analyze the interrelations of energy flow, material flow and pollutant flow in Chinese iron and steel industry through the latter model, and indicates the directions of improving the resource efficiency and energy efficiency, and decreasing the environmental load. Section 4 concludes."

Jan 1, 2008

By David Goodman

The typical operating conditions in Solvent Extraction plants are presented. The various materials of construction used for solvent extraction equipment are reviewed and the history of their use presented. The properties of the materials in common use today, stainless steel, thermoplastics and fiber reinforced plastics, are compared together with cost data. The manufacturing and construction aspects of these materials are discussed.

Jan 1, 2003

By C. L. Kusik

Environmental issues are having a significant impact on how automobiles are designed and ultimately disposed of at the end of their lives. On one hand, increasing concerns about landfill disposal have resulted in greater attention being focused on recycling materials and components from old junk autos. On the other hand, corporate average fuel economy (CAFE) requirements have led to downsizing, use of coatings, materials substitution and other measures that often make recycling more difficult. Automobile makers have responded to Corporate Average Fuel Economy (CAFE) Standards in a variety of ways such as: Downsizing; Designing of more fuel efficient engines; Reducing aerodynamic drag by sleeker body designs; Redesigning by using thinner gauges of coated steels; and Substituting material such as lightweight plastic or aluminum parts for steel. Other driving forces affecting production techniques, choice of materials and recycling issues include the Clean Air Act and its amendments, RCRA. and other environmental legislation. The variety of materials used in automobiles makes the recycling issue extremely complex. Not only does one have different materials used in different automobiles for making similar parts, but changing designs, evolving environmental issues, landfill closures affecting solid waste disposal, and increasing raw material quality standards have created a complex set of dependencies related to materials use and recycling.

Jan 1, 1994

By Marco A. S. Aguiar, Luis G. S. Sobral, Vânia Mori, Paulo A. Medeiros da Silva

"Copper occurs in the crust of the earth, predominantly, as sulphides. Among the copper sulphide minerals, the chalcopyrite is the most abundant and the most refractory to the conventional oxidative processes. This work aims at developing an electrolytic process for treating a copper sulphides flotation concentrate, more precisely chalcopyrite (CuFeS2) and bornite (Cu5FeS4) in the percentages of 70 and 30%, respectively.This paper presents a low-cost operational electroleaching process for treating copper sulphides flotation concentrates, with a high chalcopyrite content. This research practical work aims at improving the copper extraction from that sulphide mineral, in a relatively short time with low-operating cost taking into consideration the influence of a cationic surfactant. The electrolyte of the electrolytic reaction system was a 2,0 mol.L-1 NaCl solution containing CTAB, a cationic surfactant. The electroleaching system contains one DSATM (dimensionally stable anode) anode and two nickel or copper foams (threedimension electrodes. During the electroleaching process the chloride ions are oxidized to chlorine at the anode surface, which in contact with the aqueous phase generate enough hypochlorite ions to oxidize chalcopyrite.The copper ions released from the chemical oxidation process are reduced at the cathode surface as metallic copper."

Jan 1, 2008

By Matthias Schnitzler, Herbert Pfeifer, Ralf Bolling

"To transform metals high temperatures are usually needed. A fast and efficient heating can reduce the C02 emitted. The fastest way to heat metals is called direct flame impingement (DFI). The flame impinges upon the item being heated. For this method it is important to know the shape and length of the flame. Laser-induced fluorescence (LIF) technology allows measurements of a two-dimensional field without influencing the reaction or the flow. Commonly used is the measurement of OH-radicals, an indicator of the reaction zone.In the presented study measurements of a turbulent diffusion flame are shown. The position of the reaction zone and the influence of the distance between the item being heated and the burner are investigated. Conventional measurements and LIP-measurements are compared and the potential of DFI to increase the efficiency of heating metals is discussed.IntroductionDuring industrial heating processes a fast and efficient heating technology is required. Two important aspects are the NOx emission and the energy efficiency. The direct flame impingement (DFI) technology has the highest heat transfer rate possible with a gas/air flame. The turbulent high velocity flame jet impinges upon the item being is heated [ 1]. Due to the high heat transfer rate furnace and exhaust gas temperatures are lower. Therefore the energy efficiency is increased and the amount of NOx emitted is reduced.Hydroxyl- (OH-) radicals are an intermediate product that is generated during the combustion of hydrocarbons [2]. They are commonly considered as an indicator for the reaction zone and position of heat release. Figure 1 shows the hydroxyl-mole fraction in dependence of the distance along the gas flow. The figure clearly shows how fast the OH-concentration increases in the reaction zone. Figure 1 also shows that OH-radicals are present in the post combustion region, however in smaller concentration [3].The laser-induced fluorescence technology serves to measure the spatial distribution of OH-radicals in a two dimensional cross-section area of the flame. Therefore the flame dimensions and location can be determined with high spatial resolution without influencing the flow or the reaction [ 4,5]."

Jan 1, 2012

By Nico Steenekamp

At Lonrho Platinum in South Africa, ores from both the Merensky and UG2 reefs of the Bushveld Igneous complex are treated by flotation and smelting to produce a nickel-copper matte which serves as a collector for the platinum group metals (PGM' s). The nickel-copper matte was originally shipped to Norway for treatment and recovery of the contained base metals, with the return of the PGM rich concentrate to South Africa. The Lonrho Platinum Base Metal Refinery was commissioned in 1985. The original process employed a Shenitt Gordon design. The converter matte is treated in a refinery which utilises both atmospheric and pressure leaches for the dissolution of base metals to produce nickel sulphate crystals, copper cathode and a PGM concentrate. This paper refers to flowsheet and operating changes as well as improvements within the Base Metal Refinery.

Jan 1, 1999

By S. Suda

Hydrogen storage materials have been investigated for more than 30 years, particularly on metal hydrides. These materials are, however, considered today impractical because of their poor hydrogen capacity measured by mass density and their poor surface properties and characteristics against impurities. Recent R&D activities have been located in new categories of materials such as complex hydrides and chemical hydrides. Among these materials, NaAlH4 (one of alanates), Li-based complex hydride, and NaBH4 (SBH: sodium borohydride) are 3 major candidates as hydrogen storage materials. In the presentation, SBH as a non-reversible on-site but recyclable off-site is described in view of its practical availability as the source of H- (protide) applied for a new type of fuel cell named Direct Borohydride Fuel Cell (DBFC) and H2 (hydrogen) for Proton Exchange Membrane Fuel Cell (PEMFC).

Jan 1, 2006

By N. L. Piret, E. N. Mounsey

Ausmelt technology is successfully used to process primary and secondary materials to produce lead in large-scale commercial operations and to meet stringent environmental standards. The development and commercial data covering these applications and the results with respect to metallurgical, cost and environmental performance are reviewed in commercial operations. A new smelter is scheduled for commissioning in 2000 at Korea Zinc's Onsan site to process lead fume and other secondary materials to produce 50,000 tonnes per annum of lead bullion. The unique features of Ausmelt technology also allow for the efficient processing of polymetallic concentrates and secondary materials, particularly copper and lead, through the effective separation of these elements into metal, slag and fume species. This capability has been successfully demonstrated at a commercial scale and the results and implications for the industry are discussed.

Jan 1, 2000

By Justin Karl, Ali Gordon, James DeMarco, Yongho Sohn

"Aluminum metal-matrix composites are lightweight materials that have the potential to supplant steel in many applications. The current work helps to identify the parameters that confer maximal strength and ductility. Torsion tests were performed on the as-cast aluminum metal-matrix composite A359-SiCp-30% at a variety of temperatures and twist rates. Dependence of material properties on temperature and strain rate were identified from equivalent stress-strain curves constructed from the reduced data. Examination of the microstructure was performed on the as-cast material and on fracture surfaces. A temperature-and strain rate-dependent constitutive model was applied to simulation of the mechanical response of the torsion specimen. Trends in material properties corroborate and extend trends identified previously under tensile loading with regard to temperature and strain rate dependence. Shear properties of simulated specimens agree with properties obtained through experimentation.IntroductionAluminum metal-matrix composites (A1-MMCs) have become increasingly popu1ar in recent years. While unreinforced aluminum alloys have low densities and high ductilities, they are not suitable for many applications due to their lack of strength and stiffness. To provide added strength and stiffness while maintaining favorable densities, it has become common to reinforce aluminum alloys with silicon carbide in various forms, although usually the inclusions are in the form of whiskers or particles. The result is a composite material with superior specific strength and stiffness. While whisker-reinforced composites are expensive due to the necessity of processing by nonstandard techniques and have low transverse properties when rolled, particle reinforced Al-MMCs have transverse material property values almost as high as the longitudinal properties and are not as expensive to process as whisker-reinforced Al-MMCs [1]."

Jan 1, 2012

By Donghai Li, Cheng Pan, Xuyang Liu, Xuewei Lv, Chenguang Bai

"Fine chromite ore is the common raw material to produce ferrochrome alloy through the submerged electric furnace process. The electric resistivity of fine chromite ore plays an important role in the operation efficiency because it determines the current distribution. The effect of particle size and the contact area of the particles on electric resistivity for several of chromite were investigated at room temperature, and the relationship between the electric resistivity of mixed particles and the volume fraction of lump ore to fine ore was also studied. The results shown that the electric resistivity increases with the increase of particle size, and the electric resistivity of mixture decreases with the increase of volume ratio of fine ore.IntroductionChromium is one of the most important alloying elements in manufacturing of stainless steel that used at high temperature and corrosive environment applications [I, 2]. As the raw materials to be charged into the steel, ferrochromium alloys and charge chromium are produced directly by smelting of chromite ore with the reducing agent in submerged electric arc furnace (SAF). During the process, the oxides of chromium and iron were reduced by carbon and meanwhile the electrical energy were consumed [3,4]. The ideal industrial process is to achieve high recovery level of Cr and Fe with minimal power consumption. In SAF process, the electric resistivity of charge stock has significant effect on the current distribution, which determines the heat distribution, molten bath structure and chemical reactions in the furnace. High resistance of the charge is desired to reduce the current distribution through the charge stock, thus the electrodes may insert into the charge stock with proper depth to form a high temperature arc heat source, and proper smelting can be realized[5]."

Jan 1, 2012

By Thomas Schemmel, Bertram Kesseiheim, Helge Jansen, Uwe Kreme

"During the last decades the refractory life time of the different aggregates of the secondary aluminium production was improved significantly. However, each repair and installation of refractory material affects the operating schedule and can cause costs in the million range. The downtime of just one melting furnace generate costs of 100.000 to 400.000 $ per day. Besides cooling down of the furnace and its repair, the heating-up procedure accounts for the longest time of the shutdown. Usually, heating-up of low cement or ultra low cement castables takes 120 to 150 hours. In order to reduce such expensive downtimes Refratechnik developed a unique and novel product series: Nanobond. These materials can be heated-up in only a third of the usual time. This paper talks about the theoretical aspects, as well as the mechanical and physical properties and especially practical experience of using Nanobond.Theoretical Aspects and Laboratory ResultsCement containing castables such as RCC, MCC, LCC or ULCC are considered standard in many refractory applications. Over the years a wide range of possible raw materials and practical installation methods were developed. However, all of these cement bonded refractory mixes possess one main important drawback. Such materials are characterized by the hydration of the cement bonding. As a result the physical bonded and the hydraulic water has to be removed in a relatively complicated drying procedure. The hydraulic water specifically demands a very careful and cautious heating up procedure. Most of the dreaded steam explosions can occur at a furnace temperature of approx. 250 oC. [1] To avoid such destructions, the heating-up of a new lined or repaired furnace can be very complex and slow. Depending on the furnace or the casted part a drying time of several days with long curing times are common."

Jan 1, 2012