Search Documents

By John Rudolf

Metropolitan Washington Airport Authority is currently undertaking the first Phase of Metro?s Extension to Northern Virginia. A wide range of tunnel options was considered for the Tysons Corner segment that involves about 20,000 feet of track and four stations. After consideration of many options that involved EPBM single track tunnels, NATM tunnels and large bore tunnel concepts for the entire Tysons alignment, the design now being progressed into construction involves two 520 meter (1,700 feet) long soft ground NATM tunnels with several hundred feet of cut-and-cover construction. The paper discusses the process that led to selection of the short NATM tunnels as the most feasible of the options considered for Tysons.

Jan 1, 2008

By Marc Dondelinger

Interlocking H sections with deep webs and high section modulus are being used for cofferdams and shore enclosures where pressures are excessive. The H sections can be as much as a meter deep; they can be used as continuous interlocked wall. A steel saving alternate is spacing the H and driving deep for stability then filling between with shorter interlocking sheet piles. Templates provide for exact positioning.

Jan 1, 1985

By Kazuyuki Matsuzawa

A series of plate loading tests were carried out on a loam ground in order to investigate the influences of the plate size and the loading rate on the observed load-settlement relations. Two circular plates having diameters of 0.3 m and 1.0 m were used. Three types of loading methods were employed; 1) static cyclic maintained load test, 2) static continuous load test, and 3) rapid (dynamic) plate load test. An interpretation method called non-linear damping method was used to estimate a static load-settlement relation from the rapid plate load test signals. The derived static load-settlement relations match well with the measured results from the static load tests.

Jan 1, 2006

The gold concentration profiles which develop inside the activated carbon particles during the adsorption process were measured, so as to obtain additional direct proof of intra-particle mass transfer rate-control and to determine how individual carbon particles in a population vary in their gold uptake behaviour. The observed gold concentration profiles inside the activated carbon particles were typical of situations where an intra-particle mass transfer mechanism is rate-controlling. Gold di-cyanide penetrated the carbon particles with a wave-like front until it was uniformly distributed throughout the particle. This corresponds with the profiles predicted by the film and surface diffusion model. However, the rate with which gold di-cyanide was transported inside the individual carbon particles varied within the population of carbon particles. This variation was characterized by a lognormal distribution in surface diffusivity. Because the estimated variances of these surface diffusivity distributions were small, the dynamic adsorption behaviour of the carbons used in the present study did not deviate significantly from that predicted by a model based on film mass transfer and a single surface diffusivity. Van Deventer (1984, 1985 and 1986a) reported data that could not be adequately described by a model based on film mass transfer and a single surface diffusivity. In this study a model based on film mass transfer and a wide lognormal distribution of surface diffusivity values was applied to his data. It was shown that a population of carbon particles with a wide distribution in surface diffusivity values could offer an alternative explanation to the mechanism proposed by Van Deventer which was based on film mass transfer, with partitioning of the carbon into micro- and macropores with surface diffusion in the macropores and slow mass transfer into the micropores.

Jan 1, 1997

By A. Drouin, D. Lemieux, C. Chouinard

"A gold bearing pyrite concentrate was treated at the demonstration scale (15 t/d) for the extraction of gold using a cyanide-free process. The pyrite was depressed in the flotation circuit in order to promote the flotation of copper and to achieve a sufficient copper grade to meet the copper smelter criteria. However, the recoveries of copper were 80% and only about 50% for the gold was found in the copper concentrate. The balance of the gold (50%) and copper (20%) contained in the pyrite concentrate as a reject from an overall flotation circuit. The gold grade in the pyrite concentrate is 5.40 g Au/t and copper about 0.77%. About 170 tons of pyrite concentrate were processed in the DST demonstration plant. The concentrate was first oxidized using a fluid bed to produce a calcine. Copper was then extracted as copper sulphate using diluted sulphuric acid. The residual solid was submitted to the DST chlorination process for gold extraction. Thereafter, the gold was recovered from the pregnant brine by precipitation over silica using DST proprietary process. The maximum gold recovery by chlorination was 90%. The average gold recovery by cyanidation of these calcines was 71%.IntroductionDundee Sustainable Technologies (“DST”) has developed a chlorination process as an alternative to the conventional cyanidation process for the extraction of precious metals from ores or concentrates. The technology offers viable and efficient gold recoveries and the ability to handle refractory ores and contaminated material (As, Hg, etc..). The process was successfully demonstrated on hundreds of samples provided by various mines, exploration and development projects and has evolved from laboratory experiment to demonstration at an industrial scale.DST’s chlorination process operates in a closed loop circuit, which implies that no liquid effluents are generated. The chemistry and process design allows precious metal deposits containing base metals to be treated viably. The tailings from the process are inert and non-toxic, sulphide depleted and thus non-acid generating. The efficiency of the process has demonstrated excellent gold recoveries within a fraction of the time needed for cyanidation to obtain similar results. The company completed in 2015 the construction of the first industrial demonstration plant operating with the DST technology. The plant has a capacity of 15 tons per day of mineral concentrate, and the ability to extract gold and silver utilizing DST chlorination technology.DST has tested its chlorination technology at demonstration scale on the refractory pyrite concentrate containing 5.40 g Au/t and 0.8 %copper. This auriferous pyrite concentrate, was by-product of copper concentrate respecting the copper smelter norms, is produced in a country where cyanide is prohibited and refractory to cyanidation. The pyrite concentrate was initially processed successfully (gold recoveries: > 90%) by the DST technology at laboratory (2011: 20 kg) and pilot (2014: 5 tons) scales to extract gold. About 170 tons of this pyrite concentrate were processed in the DST demonstration plant located in Thetford Mines."

Jan 1, 2017

The Greymouth Coal field is situated on the West Coast of New Zealand's South Island and has been mined for coal for more than 120 years. The area covered in this paper is within the Rapahoe Sector of this field and contains >200 million tonnes of low ash, low sulphur, bituminous rank coal. Paper No 6, presented to the 19th Annual Conference of the New Zealand Branch of The Australasian Institute of Mining and Metallurgy in Christchurch in August 1985 by R G Bowman, explained 'A Geologist's View' of the 'Economic Potential of the Greymouth Coalfield', and describes previous geological assessments of the Rapahoe Sector.

Jan 1, 1989

By Francis E. Federspiel

A mineral purvey of the Granite Chief RARE II area (A5-261), covering about 23,400 acres (9,470 ha) of Tahoe National Forest and the Like Tahoe Management Unit, was conducted by the U.S. Bureau of Mines and the U.S. Geological Survey in 1979 and 1980 (fig. 1). The investigation by the Bureau of Mines indicates that the area has a low potential for mineral resources. Samples taken from prospect pits and favorable outcrops indicate no minable quantities of precious or base metals. Placer deposits are too small and low grade to be considered a resource.

Jan 1, 1981

By A. Mazhary

"Although ore sorting in mining is not a new concept, sensor-based sorting has failed to gain broad acceptance due to perceived challenges with the technology. In order to gain wider applications, this research focuses on treating waste rock and low-grade ore to identify and test appropriate sensors and to evaluate the response. Results showed that amenability of rocks to sensor-based ore sorting is both sensor and ore specific. It was also observed that the efficiency (recovery) of sorting is directly influenced by the degree of heterogeneity of the rocks. The overall outcome showed that with the right sensor, several of the materials tested are amenable to sensor-based ore sorting. Mining companies could benefit from multiple economic and design impacts, such as lower energy cost, lower transportation costs, higher metal recoveries and smaller footprints that lead to more sustainable mining. This paper will focus on the effects of heterogeneity of rocks on sorting potential and efficiency.IntroductionSensor-based ore sorting has been attracting more attention since the pressure for effective resource extraction and management has increased. An urge to make most of the current deposits, and to make the low-grade deposits economic to mine has ushered the technology to find new ways to overcome the new challenges. No matter the terminology used, such as coarse beneificiation, waste rejection, particle or bulk sorting, the purpose of sensor-based ore sorting is to remove low-grade rocks before the comminution circuit, increasing the feed head grade and quality while reducing the energy costs related to comminution.Despite nominal advantages, there have always been some concerns that have impeded the intorduction and acceptance of the technology. One of the most important shortcomings of ore sorting is their capability, or capacity, to keep up with the high-tonnage mining. Some other issues that have been mentioned as drawbacks to sorting include installation cost of such devices, feed preparation for effiecient sorting along with accuracy of sorting and probability of false negatives (Manouchehri, 2003)."

Jan 1, 2015

By M. Rantapaa

Measurable improvements in throughput have been documented at Barrick Goldstrike due to increased ore fragmentation through efficient drilling and blasting techniques. A decrease in throughput at the autoclave, due to increasingly hard ore, was identified in early 2002. A team of individuals from the open pit and process areas worked closely on the Drill-to-Mill (D2M) Continuous Improvement initiative to ensure that it would address the needs of both groups, with the target of actually improving throughput in future years, despite the projected harder ores. A series of tests were conducted to determine if adjustments to drilling and blasting could positively influence throughput. Better fragmentation and a subsequent increase in mill throughput were achieved through the use of electronic caps for more precision and flexibility, as well as for allowing extremely fast shots; explosives with a higher velocity of detonation (VOD) to provide for improved shock energy; and improved distribution of the explosives by decreasing pattern spacing. Early tests indicated a significant increase in throughput when processing identified harder ore. It is anticipated that the total process throughput (hard and soft ore) will increase by 6 tph in 2003 due to the improved fragmentation of the hard ore. Barrick Goldstrike?s D2M initiative includes roaster hard ore (BWI>17), as well as autoclave hard ore (BWI>15). Approximately 6 million tons of D2M material were shot in 2003, a relatively small amount compared to the 150 million tons to be mined. The benefit of additional ounces produced should far outweigh the additional drilling and blasting costs.

Jan 1, 2005

Eco-Efficient Gravity Separation Solutions in India Sustainable development and social responsibility issues are a principal aspect of mineral processing operations around the world. With the need for more environmentally effective technologies, some gravity separation systems have provided eco-efficient mineral processing solutions in places where it is not otherwise viable because of lack of fresh water or for other environmental reasons. Advanced spiral separation technologies developed in Australia offer a cost effective and environmentally viable way to process minerals. In particular, we review recent case studies of spiral plants commissioned in India where environmentally sustainable solutions to design problems included the use of spirals operated with sea water and the use of high capacity (HC) spirals to provide low consumption of energy and materials and a reduced plant footprint. This paper evaluates the performance of various spiral plants in India and how critical environmental issues which affect the overall viability of wet concentrating processes where resolved.

Sep 13, 2010

By R. Mckinstry, M. Rantapaa, T. Bolles

"Measurable improvements in throughput have been documented at Barrick Goldstrike due to increased ore fragmentation through efficient drilling and blasting techniques. A decrease in throughput at the autoclave, due to increasingly hard ore, was identified in early 2002. A team of individuals from the open pit and process areas worked closely on the Drill-to-Mill (D2M) Continuous Improvement initiative to ensure that it would address the needs of both groups, with the target of actually improving throughput in future years, despite the projected harder ores. A series of tests were conducted to determine if adjustments to drilling and blasting could positively influence throughput.Better fragmentation and a subsequent increase in mill throughput were achieved through the use of electronic caps for more precision and flexibility, as well as for allowing extremely fast shots; explosives with a higher velocity of detonation (VOD) to provide for improved shock energy; and improved distribution of the explosives by decreasing pattern spacing. Early tests indicated a significant increase in throughput when processing identified harder ore. It is anticipated that the total process throughput (hard and soft ore) will increase by 6 tph in 2003 due to the improved fragmentation of the hard ore.Barrick Goldstrike’s D2M initiative includes roaster hard ore (BWI>17), as well as autoclave hard ore (BWI>15). Approximately 6 million tons of D2M material were shot in 2003, a relatively small amount compared to the 150 million tons to be mined. The benefit of additional ounces produced should far outweigh the additional drilling and blasting costs."

Jan 1, 2005

Rock engineering has now been practised as a discipline for about50 years, and many sophisticated methods of analysis for use in rock engineering design have been developed. However, analysis is only a tool for use in engineering design, and rock masses are often so complex that realistic modelling of them, even with sophisticated methods of analysis, is impossible. At the other end of the scale, rock mass classification methods have been developed to quantify the rock mass. These ?numbers? are now widely used for assessment of stability of underground and surface excavations in rock, for the determination of rock support requirements, and for the estimation of rock mass strength and deformation properties. In considering these areas, the two concepts?design, and prediction of behaviour?will be dealt with. The discussion will be introduced by a consideration of the characteristics of the rock mass, which will highlight the variability in its properties and hence the uncertainty in the behavioural parameters. Examples of real projects will be used to illustrate the discussion.

Jan 1, 2003

By Donald L. Brothers

"OUT IN BRITISH COLUMBIA, we have a legendary creature called ""The Sasquatch,"" a large ape-like creature which, according to those who claim to have seen it, somewhat resembles the Abominable Snowman of the Himalayas. Through the years, the legend bas been perpetuated by hunters and prospectors who return from remote wilderness areas with fantastic tales about hairy creatures, twice the height of an average human being, who leave 2-ft-long footprints in the soft forest floor. However, the existence of this creature bas never been proven and the attitude in British Columbia circles is that the whole thing constitutes either a great discovery or a giant hoax, and is about equally unbelievable either way.The Sasquatch, however, is not the only giant in British Columbia. If you find the Sasquatch story un-believable, you'll fi nd it just as hard to believe what is happening in the mining industry out west. We have opened four new mines so far this year (1967), another mine is expected to be brought into production before the end of the year and any mining man will tell you it's just the start of a mining boom which will continue for many years if metal prices are maintained and the federal government sees fit to discard the taxation changes pro-posed in the Carter Royal Commission Report regarding mining."

Jan 1, 1968

By A. B. Hooker

Nineteen of the installations were on rental contracts 1.L."'1der whtch the lamps belong to the lamp company and are rented by t.½em to the mine operatj.nt; company. · The other nine installations had been upon an O\Vnership-rental basis, by which the lamps had become the property of the renter at the end of 5 years. Five of t.11e rentec installations were en a special contract calling for a guaranteed light output. These contr2.cts were based upon certified . initial performance, with the provision that the lamps be replaced whenever periodic tests of fully charged lamps, taken at random from t..h.e charge racks, showed a light output of less than 80 percent of the certified performance.

Jan 1, 1942

By J Hadijigeorgiou, R. W. Lawrence, R Pouling

The layered co-mingling method involves the disposal of waste rock with the addition, at predefined construction stages, of layers of dewatered mine tailings. The resulting waste structure displays bulk properties that are more favourable to acid rock drainage (ARD) control than the constituent materials alone. A laboratory test programme was conducted to examine the potential of this method. Columns containing different configurations of waste rock and tailings were percolation leached for 40 weeks and the leachates examined for various parameters. In the short term the chemical reactions that result from the introduction of dewatered tailings into rock waste can significantly improve the quality of the drainage. Columns with co-mingled material produced leachate with pH levels of 8, whereas leachate from the control column containing waste rock alone had a pH of 4. Larger-scale field tests are planned to determine the effect of the disposal method over the longer term

Apr 1, 1996

By J. Nesset, F. Rosenblum, P. Spira

"Sulphide concentrates may exhibit self-heating to various degrees during storage or shipping, the worst cases presenting a serious hazard from fire and SO2 emission. Based on measurements of heating rates on a wide variety of concentrate samples in a special apparatus, combined with field experience, a methodology has been developed which allows concentrates to be rated for their heating potential. This has proven to be very useful in practice, for example, in deciding on the need to take preventive measures. Oxidation under ambient conditions in the presence of moisture initiates heating locally within a stockpile. In the case of highly active materials, such as those that contain abundant pyrrhotite, heating may progress through three stages to temperatures well above 5000C. However, most concentrates show little or no propensity to selfheat. Heating rates were used to estimate values of the heat output, or self-heating capacity (in joules per gram), which sustains the process at each stage. Thermal data from differential scanning calorimetry are also reported. Variables which affect self-heating are discussed and an actual case of heating control on a stockpile by covering is described. A simple apparatus which can be used to simulate stockpiling conditions has been tested successfully and is proposed as a convenient test system.INTRODUCTIONPrevious publications from this laboratory on the evaluation of self-heating in sulphides dealt with tailings backfill (Rosenblum et al. 1982) and waste rock (Rosenblum and Spira 1995). Sulphide concentrates may likewise exhibit self-heating in storage or during shipping. In a comprehensive but dated review, Kirshenbaum (1 968) pointed out the conflicting nature of information on means of controlling the problem, particularly with regard to the application of water and ventilation. Modelling by Simpson (1 97 1) of autogenous heating in stockpiled zinclead concentrate and associated field measurements by Wright et al. (1972) showed that the supply of oxygen by wind and the shape of the piles were the major factors in the development of hot spots. Simpson did not attempt to explain the complex mechanism of self-heating, simply ascribing its onset to oxidation. Pearse (1 980) investigated a potential method of testing for selfheating which consisted of (i) reaction with hydrogen peroxide and (ii) differential thermal anal sis, to characterize the response of concentrates at both ambient and temperatures above 100 C. He found the method sensitive enough to identify the need for careful handling but not to predict ignition. He recommended compacting concentrates and covering stockpiles with plastic sheeting to prevent ingress of air. All these workers recognized the key role played by oxygen and moisture in triggering self-heating."

Jan 1, 2001

By Eric R. Borys, Amaneh E. Kenarsari, Brett Gitskin

This case study discusses impacts of excessive Earth Retention System (ERS) lateral movement at a project in city of Chicago. The ERS (cantilevered sheeting) moved inward towards the excavation and caused lateral displacement and cracks in six drilled shafts located about 1 to 2 lateral feet (0.3 to 0.6 m) from the face of the sheet pile wall. Up to 9 inches (23 cm) of horizontal movement was observed on top of the supporting sheet-pile. Similarly, survey measurements showed the top of the drilled shafts moved laterally up to 8 inches (20.3 cm). To evaluate the cause of failure and determine a remediation solution, the soil, shaft and site conditions were investigated. Pile Integrity Tests (PIT) were conducted at the affected drilled shafts. The shafts with identified anomalies were cored and video-recorded. The cause of the failure was determined to be related to variable soil conditions across the site, deeper excavation (i.e., increased effective ERS wall height), and other differences between design and as-built conditions. Internal bracing, in the form of walers and rakers, was installed to limit further movement of the sheet pile as a short-term solution, with additional grade beams framed into the basement slab-on-grade as a long- term solution. Five of the six cracked shafts were spliced with reinforcing bars and high strength grout and one shaft was replaced. INTRODUCTION The subsoil in the Chicago Area mostly consists of glacial till clays underlain by water-bearing granular soil over bedrock. The glacial clays have very soft to medium consistencies for a typical thickness of 30 to 50 feet (9.1 to 15.2 m) below which hard clays (Hardpan, i.e., heavily over-consolidated clay soils) are encountered. The soft clays are often referred to as the “Chicago Blue Clay”. Beach Sands are also found above upper soft clays in several areas, especially within a three-mile strip near Lake Michigan (Peck and Reed 1954). Due to the existence of soft clay in Chicago area, supporting the mid to high rise buildings on drilled shafts extended to Hardpan is a common practice in modern building design. In the early 19th century it used to take about 3 weeks to excavate 1 shaft hole and about 1½ days to fill the shaft with concrete in Chicago (Manierre 1916). The early 19th century methodology of excavating a shaft consisted of hand digging the shaft, installing wood lagging as temporary shoring with spoils removed with a rope and pulley system from the surface. Today, the excavation of a typical drilled shaft in Chicago uses heavy drilling equipment and requires much less time for excavation and concrete placement. It is not uncommon for contractors to excavate shafts and place concrete at a rate of about 2 to 5 drilled shafts per day (with one drill rig).

Jan 1, 2018

By Les Gutzwiller

Fan applications in the mining industry have changed during the last 70 years. In 1922, J.R. Robinson authored a technical volume entitled Practical Mine Ventilation. At that time, atmospheric control had only recently shifted from natural to mechanical. The large, mechanical draft fans that were used then were centrifugal. The fans ran at low speeds, about300 rpm. Most were steam-engine driven. In the late 1920s and early 1930s, mines became larger, increasing the pressure and volume requirements of the fan equipment. Axial fans were designed to run at much higher speeds (710 to 880 rpm) and were driven by electric motors. They were also smaller and less expensive to install than the cumbersome centrifugal units. However, changes in mining have resulted in progressively higher static-pressure requirements. So centrifugal fans are once again proving to be a good choice.

Jan 1, 1999

By Laura Bastemante, Bruce Vandenberg, Fred Huettig

Recent advances in solid-state, field portable, fast framing video camera systems and PC based frame capture hardware now allow blast imaging up to loo0 frames per second. Up to 8 seconds of data can be stored directly into the unit, downloaded to a PC or archived to a standard VCR without data compression. Since no film processing is involved, motion analysis can be performed instantly and on-site within a few minutes. This paper will describe the design features and applications of the KineView 1256P system and compare these with the analogous aspects of film based cameras.

Jan 1, 1997

By W. P. Johnstone

The computer assisted generation of geological models to represent the geometry of, and grade distribution within, orebodies is a rapidly growing area of the geological profession. Such models are increasingly used as a necessary starting point in determining the mineability of mineral deposits in terms of practical mine design and economic considerations. The transition from traditional techniques such as field or underground mapping and the manual calculation of grade and tonnage estimates, as well as related activities such as the interpolation of cross-sections, the use of stereographic projections, core logging and hand contouring, to computerized applications, is by no means complete. In fact, many geological professionals deliberately avoid the use of computer simulations based on the perception that the resulting models are simplistic and that their construction is not founded on sound geological principles. The purpose of this paper is to assess current thinking on this topic by considering; (a) an overview of advances in the drafting of geological maps, (b) the theoretical basis for multi-dimensional geological modelling, (c) the case for combining traditional and modern techniques, and (d) the benefits to the mining value chain.

Jan 1, 2003