Search Documents

By J. E. Rourke, O&apos

This report incorporates a review of available dewatering technology and an evaluation of its relevance to surface coal mines in the Interior Province of the United States. Guidelines for the selection, design and construction of dewatering systems are included. On the basis of documented experience, candidate dewatering systems were selected and evaluated with respect to their anticipated impact on the environment and mine operations. Included in the discussion is a summary of laws and regulations which can impact on dewatering operations. Following this discussion, geologic and hydrogeologic conditions within the Interior Province are described and potential dewatering problems at surface coal mines are identified. Model mines are developed which exhibit the most difficult dewatering problems identified, and it is demonstrated how available technology can be utilized to deal with these problems. Dewatering of coarse-grained, high permeability terrace deposits might be economically feasible today. Low permeability, saturated glacial tills or lake deposits appear to be significantly outside present economic feasibility for dewatering.

Jan 1, 1979

By Ismet Canbulat, John Naylor, Jason Emery, Peter Craig, Andy Sykes

"Longwall mining is by far the most common method of underground coal extraction in Australia. The industry trends and expectations are placing increasing emphasis on the reliability and productivity of these operations. The longwalls are becoming wider and longer while retreat rates are continuously increasing due to significant improvements achieved in longwall equipment reliability and automation. This increased longwall productivity is placing significant emphasis on the reliability of longwall panel development.Although there have been significant improvements in the reliability of continuous miners and hydraulic drill rigs, the traditional resin encapsulated bolt installation is still the principal method used in all major coal-producing countries around the world. Anglo American realised an opportunity existed to introduce an alternative roof bolt installation technique called “spin to stall” in Australia. Spin to stall was first introduced in Anglo American Coal in South Africa where it has been successfully used for over a decade, though implementation of South African spin to stall resin in Australia has proven to be near impossible due to a significant difference in geotechnical conditions, mining method, and, subsequently, roof bolting equipment. Therefore, a new spin to stall development project was initiated between Anglo American Coal and Jennmar Australia (SPIN2STALL®). This paper summarises the journey of this project, the results, and the successful implementation of spin to stall achieved at Grasstree Mine.INTRODUCTIONThe Anglo American Coal business unit operates Grasstree and Moranbah North underground longwall mines in the Bowen Basin of Central Queensland, with a third longwall mine, Grosvenor, currently being developed, and two more (Aquila and Moranbah South) in the project pipeline. The vision for Anglo American is to achieve “Zero Harm” through the effective management of safety at all operations, while for the coal business unit, at the same time to achieve industry-leading operational performance. Currently, both Grasstree and Moranbah North longwalls are operating at industry best practice rates. This is placing increased pressure on the development process to allow such high productivity levels to be sustainable."

Jan 1, 2015

By Eugene A. Dolecki

This final report describes the work accomplished under U.S. Bureau of Mines Contract #H0242011 - "Feasibility of Automated Rail Haulage Systems in Underground Coal Mines." The report outlines the base for the development and evaluation of automated rail haulage systems in terms of the service requirements for haulage systems in underground coal mines, and of the performance of existing haulage systems. A generalized automated rail haulage system concept is defined. A safety impact analysis of automating the mainline portion of the underground system indicates a 50% reduction in injuries and fatalities. A cost effectiveness (over the total life cycle) study for the system indicates a cost benefit can be obtained from implementing an automated rail system. The design specifications for the total automated rail haulage system - including subsystems and components -are developed, and the equipment types and general design approaches evaluated, with selections outlined. A detailed conceptual design for a prototype automated system is described. Conclusions and recommendations are presented, and a program plan devised for implementing a proto-type automated rail haulage system demonstration in an operating underground coal mine by 1980.

Jan 1, 1976

By Gennaro G. Marino

As part of the development of a shopping center in West Virginia, a significant bench had to be cut into a mountainside that was over 700 ft. high. As a result, a steeply stepped, over 400-ft.- high wall was created. The high wall exposed old abandoned room-and-pillar coal workings at the toe of the cut. Because of exposure to the elements, the mine openings began to severely deteriorate with significant potential of undermining of the rock cut face and causing a large rock fall(s). Exacerbating this wall problem was a set of fairly planar sub-parallel and sub-vertical joints creating, in essence, thin rock slabs. Also present were stress relief fractures that were observed in the exposed pillars. Given the proximity of the project building to this high rock face, mitigation of the rock fall potential was deemed necessary. In order to prevent continued damage and deterioration of these exposed mine entries, the rubblized openings were filled with bulkhead grout and pressure injected with grout. The total amount of grout installed in these openings was about 3,945 CY. Also, a rock drape was attached to the entire face to mitigate small rock falls from natural causes. There also existed another level of mining below the ground surface and under an existing building at a depth of about 160 ft. Under a portion of the building, the pillars in these old works were second mined, and the building seemed to have been already affected by limited subsidence above this area. Also, calculated pillar safety factors in this high extraction section of the mine were too low. Consequently, these old works were stabilized by saturation grouting. An indication of overall roof distress was the significant fracturing encountered in the bedrock overburden during the drilling of the injection holes and the volume of grout placed in these holes. The total grout installed in the high extraction section of the lower mine was about 6,660 CY. This paper describes the investigation and the grouting techniques employed at the rock cut face and under the existing building to mitigate continued damage to avoid future subsidence problems at the face and the building premises.

Jan 1, 2013

By Ruth F. Brinkley

This report is the 18th of a series of reports originally issued annually, and more recently bienially, to acquaint the public with the work of the Federal Bureau of Mines in explosives technology. Part I reviews briefly the overall activities during fiscal years 1957 and 1958.4/ Part II presents in abstract form the publications prepared by the Bureau that appeared during the period.5/

Jan 1, 1961

By V. C. Kelessidis

The interaction between rock and drill bit during drilling has been modeled for many years, but a complete understanding of the phenomena occurring has yet to materialize. Successful models will allow the prediction of rate of penetration in a given environment and optimal selection of drill bit and drilling parameters, thus minimizing exploration costs. In most rock-drilling models the value of the unconfined compressive strength of the rock (UCS) is used in the predictive equations, within the concept of specific energy, and the value of UCS is the percentage of the value of the stress applied on the drilling bit in order for the bit to advance. While the exact percentage depends on the model used and it is not known with certainty, good knowledge of UCS is nevertheless required before any decent prediction can be made on rate of penetration. Determination of UCS, normally done via destructive testing, requires not only the availability of sound rock core samples but also expensive testing and significant time for the test, which frequently are not available for routine drillability predictions. Hence, a multitude of methods and techniques has been proposed for estimating UCS from various indirect and/or non-destructive measurements, or combination of measurements with neural networks, such as point load index, block punch index, unit weight, and apparent porosity, water absorption by weight, sonic velocity, and Schmidt hardness. The many proposed approaches are critically reviewed and the results are compared, and what becomes apparent is that after many years, not only in mining but also in oil-well drilling, accurate indirect determination of UCS is still an elusive goal. An equation to predict UCS from sonic velocity data is suggested based on several data sets reported in the literature. Use of the specific energy equation with UCS or sonic data and utilization of drilling data allows an estimation of the efficiency of energy transfer from the bit to the rock and of the friction coefficient. Analysis of data reported in the literature, both from laboratory and field studies, has shown that this approach is sound and enables the determination of energy transfer efficiencies and friction coefficients, which for the cases studied range between 15 and 30% and 0.15 and 0.30 respectively. Thus, the suggested data analysis approach allows drillers to focus on inefficiencies and optimize drilling practices in future campaigns. Keywords Rock drillability, unconfined compressive strength, prediction.

Jan 1, 2011

By B Small

CSA Mine, named after the nationalities of the mines first owners being Cornish, Scottish, Australian, is one of Australia’s deepest and highest-grade copper mines. A combination of the modified Avoca method and shrinking was a standard practice where production rings were fired against and bogged to waste fill. This method resulted in dilution and involved rehandling of waste material to refill the bogged stopes in the Western region and the QTS Central. The introduction of pre-charging blastholes using a wireless initiating system (WebGen™) has enabled CSA to design and fire stopes in reverse. This involves the use of a pre-charged Temporary Rib Pillar (TRP) against the waste fill material in a previously mined stope. The temporary pillar reduces dilution and improves conventional bogging as material is blasted towards the drawpoint rather than towards the waste fill material. Additional drill, prep and blast re-work is reduced or completely removed as rings can be charged prior to, in conjunction with, or after, charging of the slot. This is a safer practice as the charge crew spend no time working adjacent to a brow or open void. A TRP trial was conducted in the western orebody at CSA. The risk of exposure to a brow or open void while charging underground, and the bogger rehandling of waste material was successfully eliminated. Once reverse stoping was established in modified avoca stopes at CSA, two TRPs were implemented in challenging ground conditions in the QTS Central region. The TRPs were utilised in a retreating four-way intersection to extract a central diminishing pillar to close the level out. The ore recovered in this stope provided 5 per cent of CSA’s copper for the year. Without pre-charging with a wireless initiating system, two 5 m pillars totalling 6936 t of ore at 7 per cent either side of the stope would not have been recovered. CSA has implemented the practice of reverse stoping in modified avoca stopes using TRP for ten stopes since the successful trial. The development of additional blasting techniques enabled by precharging with wireless initiating systems is currently underway in the QTS North orebody at CSA Mine.

Mar 29, 2023

By S. Djaroudib

Keywords: iron recovery, hematite, hydrolysis, polyvinylpyridine The precipitation of hematite (Fe2O3) from ferric chloride media at ambient pressure and at temperatures below 100°C was studied as part of a program to recover a marketable iron product form metallurgical processing streams and effluents. Hematite was formed in preference to ferric oxyhydroxides (e.g. ß-FeO?OH) by controlling the precipitation conditions, especially by adding Fe2O3 seeds. The extent of the hydrolysis reaction was found to depend primarily on temperature and on the free-acid concentration. As to the latter, the controlled addition of an adsorbent of free acid, in our case the anionic resin polyvinylpyridine (PVP), was shown to allow for the nearly complete removal of iron as readily filterable Fe2O3. The hematite product typically contains = 63% Fe and = 1.5% Cl, and its composition does not change appreciably upon repeated cycling using regenerated PVP.

Jan 1, 2005

By Y. J. Wang

The ventilation network problem, having both fixed and nonfixed operating points as control devices, is examined in this paper. Emphasizing the concept of solving a system of n equations in n unknowns, this paper presents the generalized problem formulation, some conditions under which the problem does not have a unique solution, and a solution procedure based on the Newton (or Newton-Raphson) method. A numerical example is included.

Jan 1, 1989

By J. D. Bittner

The ST separator utilizes electrical charge differences between materials produced by surface contact or triboelectric charging. When two materials are in contact, material with a higher affinity for electrons gains electrons and thus charges negative, while material with lower electron affinity charges positive. This contact exchange of charge is universally observed for all materials, at times causing electrostatic nuisances that are a problem in some industries. Electron affinity is dependent on the chemical composition of the particle surface and will result in substantial differential charging of materials in a mixture of discrete particles of different composition. In the ST separator (Figures 1 and 2), material is fed into the thin gap 0.9 ? 1.5 cm (0.35 -0.6 in.) between two parallel planar electrodes. The particles are triboelectrically charged by inter-particle contact. For example, in the case of coal combustion fly ash, a mixture of carbon particles and mineral particles, the positively charged carbon and the negatively charged mineral are attracted to opposite electrodes. The particles are then swept up by a continuous moving open-mesh belt and conveyed in opposite directions. The belt moves the particles adjacent to each electrode toward opposite ends of the separator. The electric field need only move the particles a tiny fraction of a centimeter to move a particle from a left-moving to a right-moving stream. The counter current flow of the separating particles and continual triboelectric charging by carbon-mineral collisions provides for a multi-stage separation and results in excellent purity and recovery in a single-pass unit. The high belt speed also enables very high throughputs, up to 40 tonnes per hour on a single separator. By controlling various process parameters, such as belt speed, feed point, electrode gap and feed rate, the ST process produces low carbon fly ash at carbon contents of 2 % ± 0.5% from feed fly ashes ranging in carbon from 4% to over 30%.

Feb 27, 2013

By Frederic M. Langevin

?? Introduction ?? LaRonde ?? History of Seismicity and Rockbursting ?? November 27th 2002 Rockburst ?? April 1st 2006 Rockburst ?? December 11th 2006 & January 11th 2007 Rockbursts ?? Seismic Risk Management Plan ?? Conclusions ?? Located in Northwestern Quebec (Can.) ?? In operation since 1988 ?? Reserves at Shafts #1 and #2 depleted ?? Production now comes entirely from Penna Shaft ?? Deepest single-lift shaft in the western hemisphere (2240 metres) ?? 7300+ tonnes per day ?? 2007 Reserves (proven & probable): ?? By-products: Ag, Cu, Zn ?? Sinking #4 Shaft (LaRonde II winze)

Feb 1, 2008

By César Cánepa

Las especies minerales son los sujetos del quehacer metalúrgico -en tanto, el diseño, la optimización operativa y el monitoreo periódico de una planta de tratamiento requieren de un adecuado conocimiento de las características de los minerales involucrados. En ese sentido, el presente texto señala las particularidades de los minerales (tamaño de grano, composición porcentual y grado de liberación) y su determinación cuantitativa a través de técnicas que ostentan sofisticación, donde la primera característica no se determina mediante técnicas no microscópicas, mientras que las dos últimas son factibles de establecer mediante la microscopía óptica, utilizando la metodología desarrollada por uno de los autores. Dicha metodología es compatible con el entorno instrumental y tecnológico de la mediana y pequeña minería, aunque puede ser utilizada con igual beneficio por la gran minería. Asimismo se presenta dos ejemplos actuales de cómo la aplicación de estudios microscópicos al proceso metalúrgico que se utiliza en la mina Atacocha, un yacimiento polimetálico ubicado en los Andes centrales del Perú, se desarrolla exitosamente en la optimización del proceso.

Sep 12, 2005

By Ronald W. Stingelin

The geology of the roof of the Pittsburgh coal bed was studied and mapped in nine contiguous counties containing the bulk of the remaining reserves of this coal bed in the northern Appalachian Coal Basin. Drill core records from Belmont and Monroe counties, Ohio, Washington and Greene counties Pennsylvania, and Ohio, Marshall, Wetzel, Monongalia, and Marion counties, West Virginia provided the data for twelve computer generated regional geologic variable maps. Four of these geologic variables (overburden thickness, vertical distance to the rider coal, lithology at the five foot horizon above the roof of the mineable Pittsburgh seam, and the number of lithologic changes within the 30 foot interval above the roof of the mineable Pittsburgh seam) were used to estimate the risk of potential roof falls by a methological scheme developed during this study. A hazard zone risk map was developed showing a generalized regional trend of increasing risk from west to east across the basin. Mapping of individual geologic variables and mapping of hazard risk can be done at any scale. The accuracy of the mapping is primarily dependent on the density of the drill core records. Geologic feature maps and the hazard risk map contained in this report are reduced (1 :500,000 scale) versions of the larger scale (1 :62,500) maps prepared for the Bureau of Mines as map folios.

Jan 1, 1979

By L. A. Neumeier

The Bureau of Mines evaluated creep properties of Zn-Cu-Ti alloys that were annealed after finish-rolling either cold) or at 480° F (249° C). Compositions ranged up to 1.25 pct Cu and 0.36 pct Ti. Most data are for sheet annealed after finish-rolling to 92-pct total reduction. Annealing times were varied at temperatures between 320° and 560° F (160° and 293° C). For a number of the alloys, annealing after hot-rolling at 480° F affects creep properties very differently in longitudinal and transverse sheet directions. The detrimental result is that the anisotropy in creep properties between the two directions can be vastly increased. Conversely, specific annealing treatments of certain heavily cold-rolled alloys result in surprisingly low anisotropy in creep properties and the low anisotropy coincides with excellent creep resistance for both directions. Supplemental data are presented on tensile, hardness, and thermal expansion properties, and microstructures.

Jan 1, 1972

By John C. Machisak

The National Safety Competition is sponsored and conducted annually by the Bureau of Mines, U.S. Department of the Interior, to give greater impetus to the building of programs safeguarding the employees of the mineral industries from disabling work injuries. The results of the 1960 National Safety Competition are presented in this publication. Mines and quarries that were awarded the Sentinels of Safety trophy for the best safety record in their competitive group and those mineral operations that ranked second, third, fourth, and fifth in the competition are listed with a summary of their achievements in preventing disabling work injuries. In addition, this publication presents statistical data on disabling work-injury experience in all other mines and quarries participating in the annual competitions.

Jan 1, 1962

By P. Choquet, F. Miller

"The development and testing of a simple low-cost gauge for measurement of tension in a cable bolt grouted in a borehole are presented. Its principle is based on a resistance wire which is wound on a 70 cm length into the spiral grooves of the wire strand cable bolt. Readings are then taken by a robust automatic data logger with a several day autonomy or by a portable readout. In order to have a complete profile of tension along the cable bolt, a number of tension gauges can be installed along its length.This paper provides a description of the development and laboratory calibration of the tension gauge and addresses the two modes of loading for a cable bolt in a rock mass, namely pure tension and shearing at a joint location.In the second part of the paper, four field tests in underground and open pit mines are reported. The first test was used to substantially modify both the gauge and the readout unit principles while the other tests which are still on-going show a very satisfactory behaviour of the modified version of the tension gauge. IntroductionCable-bolting is often used as ground support in Canadian mines for a variety of applications. In underground mines, cable bolts can be installed vertically at the back of cut and fill stopes or in an inclined fashion in the walls of large open stopes. Alternatively, cable bolts at Mines Gaspe (Noranda Inc.) are used in a fan-shaped pattern from a drill drift to stabilize the inclined roof in 25 m wide open stapes. This new application oriented our research efforts toward the design of a novel instrumentation to monitor the efficiency of most commonly used 5/8-inch cable bolts."

Jan 1, 1988

By Wilson Bardales

El presente trabajo describe la experiencia de la Gestión de la Calidad en la Cía. Minera Poderosa S.A., específicamente en el rol que desempeñan los Círculos de Mejoramiento Continuo (CMC´s) como un vehículo efectivo para alcanzar los objetivos de la empresa. Los CMC´s están integrados por trabajadores de un mismo proceso, a quienes se capacita en el manejo de herramientas, técnicas y metodologías de la calidad, con la finalidad de realizar mejoras en los procesos. En ese sentido, en la compañía minera La Poderosa, la administración es participativa y el directorio difunde las políticas, para lograr la rentabilidad de la empresa. Así también, los mandos medios definen los objetivos y estrategias, desplegándola en cascada a la supervisión y estos a su vez, al personal de línea. Este concatenamiento de responsabilidades y la participación de los CMC´s aseguran el alineamiento y control de la gestión.

Sep 12, 2005

By F. Dehghani

The influence of different grinding methods on the shape characteristics of magnetite particles was investigated. Also, the effect of particle shape on the flotation of the magnetite, both alone and in the presence of quartz particles, was investigated. The shape characteristics of the magnetite particles were measured and calculated from images obtained by scanning electron microscopy via an image analysis system. The flotation tests were performed using a laboratory flotation cell. Results showed that in the -250+212 µm and -106+75 µm size fractions, ball mill products have a higher elongation value than rod mill products, while in the -150+125 µm size fraction, rod mill products have a higher elongation value. Particles with higher elongation values and lower roundness values have a higher flotation kinetic constant. Furthermore, the influence of magnetite particle shape on flotation is greater, and the flotation kinetic constant is higher, in the presence of quartz particles than in the flotation of magnetite alone Keywords shape, elongation value, flotation kinetics, magnetite.

Dec 1, 2013

By M. A. Upham

"MINING is Canada's second largest basic industry, producing material with a gross value of 2.5 billion dollars, led only by agriculture with 2.9 billion dollars. It pro-vides employment, directly and in-directly, for three quarters of a million people. Since the Second War, the value of mineral production in Canada has tripled. Economists forecast that over the next 15 years its value will triple again. Canada is a basic and leading supplier of nickel, iron, copper, zinc, lead and uranium. It is also a major oil producer, leads the world in the production of asbestos and in five years will be the leading producer of potash, a basic constituent of fertilizer.It can be seen that Canada's wealth and economic progress lies in being a primary producer of economic minerals and in building secondary industries to manufacture finished products from these raw materials. Canada's future in the field of mineral production looks bright, with our resources just starting to be tapped. Outside of the large expanse of Soviet Russia, we are by far the world's most fertile mineral exploration area."

Jan 1, 1967

Since the end of World War n, many important developments have taken place in the investigation of the phenomenon of brittle fracture in mild steel. Fractures in certain classes of welded ships, in welded bridges, penstocks, etc., focussed a great deal of attention on the interrelationships of design factors, service conditions, and steel quality on the generation of catastrophic failures.Much publicity has been given these major failures, and there is perhaps a tendency to forget that mild steel, under certain conditions, as well known to behave in a brittle fashion in a wide range of everyday engineering applications.For instance, many who are connected with the haulage and lifting of heavy loads will be familiar with the bright "crystalline" fractures of crane hooks and chains which sometimes follow sudden jarring; those concerned with the heavy pressing and shaping of steel plate will not be unaware that at times sudden brittle splits or tears will develop for no obvious reason in, say, rolled pipes or in dishings.In fact it will be evident upon reflection that in many cases the conditions which mild steel has to withstand during processing into an engineering part or structure are more severe than those it wili be called upon to endure during service. In this sense brittle fractu;res in mild steel are much more frequent than are commonly supposed.Two modes of fracture are now generally recognised to occur in metals, namely, shear and cleavage. The latter manifests itself by the so-called "crystalline" fracture (here...

Jan 1, 1954