Search Documents

By Walter T. Lewieki

"INTRODUCTION Numerous deposits of iron ore are found in Cherokee, Bartow, Floyd, and Polk Counties in northwest Georgia. The deposits are generally small and irregular in shape. The ore is usually referred to as ""brown ore"" and is predominately limonite. The crude or ""bank ore"" has to be washed and concentrated before being shipped.The proximity of the deposits to the Birmingham furnaces and a favorable freight differential permit the operation of many deposits that otherwise would be uneconomical. The district produced 413,468 long tons of brown-ore concentrates, averaging 45.53 percent iron in 1943.The necessity of developing additional iron-ore reserves for the war energeucy to supplement the production of the Birmingham district, prompted the Bureau of Mines to initiate exploration of the more promising northwest Georgia deposits. Thirteen properties in the four counties were explored during the program (fig. 1).HISTORY AND PRODUCTIONSeveral furnaces were operated in the district until the early 1900's, ranging from charcoal furnaces to more modern plants with capacities up to 50 tons of pig iron. No furnaces have operated for about 40 years, the product being shipped to Alabama and Tennessee.Bartow County iron mining is declining, although formerly it was the principal producer of the district. Most of the known merchantable ore deposits have been exhausted. For the past 3 years the Mitchell-Hodge mine has annually produced about 225,000 long tons of concentrates containing 46 to 43 percent iron and at present is the only large producer in Bartow County."

Jan 1, 1946

Tapira Mine (Tapira, MG, Brazil) is the largest phosphate ore and concentrate producer in Brazil. The mine is an open pit, which until recently operated with a large equipment fleet and now uses a smaller fleet operated by contractors. The annual production reaches 17 Mt of ore plus 14 Mt of waste at a stripping ratio of 0.82. Defining the geological boundaries and forecasting the annual production can be a difficult task if not performed on a reliable model. The geological model has been totally reviewed as well as the estimation process. Ordinary Kriging has been used to build the new block model with P2O5 and contaminant grades. After estimation, block model validation and classification criteria definition to assess resources and reserves, the result is given by the life-of-mine plan is defined after pit optimisation and design. The Lerchs-Grossmann algorithm implemented in the NPV Scheduler was used to define the long-term production targets based on the main parameters P2O5 and the contaminants that are just important to the beneficiation process.

May 1, 2010

By Hugo de León Carvalho Cedro

O presente trabalho tem como objetivo avaliar os efeitos da degradação da superfície de lentes de contato via métodos ópticos. Sendo biomateriais, as lentes estão em contato direto com estruturas sensíveis do corpo humano e seu uso surge da necessidade de reduzir enfermidades, propiciando melhora da acuidade visual e proteção ocular. Outro aspecto relevante é que as lentes se tornam uma nova estrutura refrativa de entrada da luz no globo ocular, e desse modo devem manter características de transmitância compatíveis com a córnea. Com o uso das lentes, é esperado uma degradação natural das propriedades ópticas e superficiais da mesma. Para avaliarmos essa degradação, foi planejado um experimento com um ensaio de degradação. O ensaio de degradação visa comparar o efeito de diferentes soluções simuladoras sobre a superfície das lentes tóricas: solução extrema de acetato de potássio 5% pH5, solução fisiológica usada pelo fabricante do tipo Boston Simplus multiação e solução de água ultrapura obtida de um dispositivo milli-Q (controle). O efeito da degradação foi analisado através do estudo das variações da topografia e da transmitância da lente.

Oct 30, 2017

The history of soft and hard rock underground mining is blemished with regional instabilities of mine workings. Whilst the potential consequences of regional instability events are recognised to be high, there is a false perception that the probability of them occurring is very low. In fact, Australia has averaged more than one event per year for the past 20 years. At least five fatalities and over $100 million of losses have been associated with the events. As such, they are a core risk to underground mining and have a significant effect on the quadruple bottom line of business û safety, environment, community acceptance and economics. This paper explores the important roles that risk management has in reducing the probability and consequences of regional instabilities. It concludes that education and continuing professional development are essential elements for effectively managing the risk.

Jan 1, 2003

By J. P. Rider

Average production from longwall mining operations in the United States has risen from approximately 800 tons per shift in 1980 to over 4,600 metric tons per shift in 1999. Such a large increase in production has the potential to generate significantly more dust. Previous NIOSH research has shown that, on average, respirable dust levels generated by the shearer accounts for 50% of the airborne dust generated during longwall mining. Ventilating air and water are primary controls being used in an effort to reduce longwall dust levels. Longwall operators are applying more air and water than ever before and have expressed concern over reaching maximum practical limits for these controls. Full-scale laboratory tests are being conducted to evaluate the impact on shearer-generated dust levels for changes in face air velocity, water quantity at the shearer, water spray pressure, spray system design, mining height and cutting direction. Results of this research should identify the most appropriate control levels for various operating conditions. In addition, general recommended dust control practices for longwall mining will be discussed. KEYWORDS Longwall, coal dust

Apr 1, 1975

By Benj. Lyman

The Institute, in June, 1881, visited Low Moor in Alleghany County, Virginia, on the Chesapeake and Ohio Railway, seven miles easterly from Covington. Having occasion myself, a few days later, to make a very hasty geological reconnaissance of the iron-ores there, and finding them to be somewhat different in age from what was said to be the opinion of some of those who were there with the Institute, I have thought it worth while to bring the matter up again at the present meeting. According to the opinion quoted, the principal ore-banks belong to the Oriskany sandstone; and that seems to be the view entertained of the same ore in that region by Prof. Wm. B. Rogers in his reports of 1837 and 1838. it is likewise given by Prof. J. L. Campbell in a paper on the Rich-patch iron region in The Virginias for December, 1880 (vol. i., p. 189). A comparison, however, of the section at Low Moor with sections in Pennsylvania, shows clearly that the main ore-bed is the same as that of the bottom part of the Marcellus shales (part of Pa. and Va., No. VIII), a short distance above the top of the Oriskany sandstone (No. VII). The Upper Helderberg limestone is absent at Low Moor, as indeed it is at many places in Pennsylvania, and that is perhaps the reason why the ore has been thought to belong to the Oriskany sandstone. The ores and their accompanying rock-beds, are exposed in three or four folds near the Low Moor iron-mines on Fork Rim and, as described and pointed out by Mr. Geo. T. Wickes, who had in his management of several years' duration become well acquainted with them, are as follows, from above downwards:

Jan 1, 1886

By E. L. McHugh, R. T. Mayerle, J. M. Girard

Ground control problems at surface mining operations can occur for a variety of reasons. Stress, gravity loading, rock strength, geology, pore pressure, weather effects, underground workings, and many other factors contribute to slope instabilities that range from small rock falls to massive slides of material. While some of these failures can be predicted or controlled by preventive measures, each year many completely unexpected failures occur. Current methods for monitoring generally involve measuring displacements at a few, selected points in and around the suspected area of instability. While most of the displacements along these points will be in a downslope direction, freeze-thaw cycles of water-filled joints, horizontal stresses or pressure, buoyancy in saturated soils, human measurement errors, or other situations can produce deformation in almost any direction, even without any instability in the slope. Determination of which, if any of the observed movements represents a potential hazard is essential. Because of the enormous surface area of many large open-pit mines, several varieties and scales of instability can occur. Small, unexpected rock falls may indeed be more hazardous than a massive failure that involves slow displacement of material over a longer period of time. Complete vigilance to detect all small potential falling blocks is neither feasible nor economical and certainly is not attainable using today's most common point displacement monitoring techniques. As part of an on-going study at the Spokane Research Laboratory, several new methods for monitoring slope instabilities are being investigated. This paper describes the potential adaptation of systems such as interferometric synthetic aperture radar, imaging spectroscopy, and time-domain reflectometry, to slope monitoring and design.

By G. Van Weert

Refractory gold ores and auriferous concentrates containing silver tend to form refractory silver jarosites during pressure oxidation. Earlier work with pure Ag2S has shown that the addition of iodine species to the autoclave feed yields cyanide soluble iodargyrite (Agl) instead. Near complete silver extractions from the autoclave product were obtained at a I-/Ag+ ratio of 5 or more. This paper reports on the pressure oxidation and cyanide leaching of two industrial refractory (arseno) pyritic silver-bearing concentrates: 1. from Peru (sulphosalts) and 2. from the USA (pyrite, with acanthite occlusions). While using a I-/Ag+ mol ratio of only 1 in the feed, it has been possible to obtain 98 and 97% Ag extraction from the two autoclave products by cyanide leaching, respectively. This compares to 11 and 54% Ag extraction from the as-received concentrates and 4 and 15% Ag extraction, respectively, after pressure oxidation without KI present. The results of the testwork are discussed in terms of concentrate mineralogy and pressure oxidation conditions.

Jan 1, 1994

By C. H. Mathewson

EXCEPTING the joint sessions on gases in metals held during the day on Tuesday, the Institute of .Metals opened its activities with a division dinner at the Commodore on Tuesday evening, with Sam Tour, retiring chairman, presiding. W. M. Corse, secretary-treasurer, outlined the financial status of the division and stated the investment fund is becoming large enough so that in the near future it will be possible to pay all expenses of a foreign lecturer once in two years and not rely on an extended speaking tour to cover expenses. W. B. Price reported on his attendance at the Zurich, Switzerland, meeting of the International Society of Testing Materials and gave a graphic account of his visit to the Grand Salon, his meeting with Mussolini, and his audience with the Pope. Buffalo was announced as the place of the fall meeting, to be held during the week of Oct. 3.

Jan 1, 1932

By S B. Stewart, C J. Restarick

Over a four-hour period of steady plant operation samples were taken at regular intervals frum points within the grinding and flotation circuits. Size fractions of each composite sample were analysed for lead and zinc values and a comparison made of the behaviour of the lead, zinc and gangue minerals, size by size throughout the whole circuit. Analysis of the breakage behaviour using dynamic mathematical models gave the rates of breakage of each size fraction of each main component. Simulated grinding experiments shaved that the main grinding circuit had some reserve capacity. In the lead flotation circuit all lead values between 150 mesh (Tyler) and 5 ¦m had excellent flotation characteristics, and a major proportion had a high rate of flotation which was practically the same for all sizes. Increase in overall lead recovery would require improvement of the flotation behaviour of ultra-fine lead minerals. These were slav floating and were responsible for approximately half the lead losses in the final zinc concentrate and one thiro of the lead losses in the final tails. All sizes of zinc values between 150 mesh and 7 ¦m floated well and the performance of the zinc flotation circuit was mainly limited by the relatively poor flotation of the very fine zinc values. Approximately 60 per cent of the zinc lost to the final tails lay within the -7 ¦m fraction. The overall flotation conditions were conducive to very good selective flotation of the major proportion of the values and limitations in metallurgical performance were mainly due to the properties of the ultra-fines.

Jan 1, 1971

To optimise the haulage of the large tonnages produced from stopes in this high production gold mine, an ore pass and feeder system was introduced. This ore pass was designed and developed in 2006 and the plate feeder installed and commissioned soon after. Cavity Monitoring Surveys (CMS) have been undertaken of the ore pass since it was commissioned. The original thickness that was surveyed of the pillar between the ore pass and decline in 2006 was approximated to be 19 m. Throughout its use large blocks of rock were reporting at the plate feeder. This was the first indication that the ore pass was failing somewhere between the tipping level of the 9410 level and the plate feeder at the 9330. Even so CMS surveys were not taken systematically to firstly identify the area of failure or for monitoring. In August 2008 after implementing management systems, large blocks were still reporting to the plate feeder. The decision was made to empty the pass enough to carry out a CMS survey of the area. Subsequently it was discovered that the area of failure was between the decline and ore pass and that since the first survey the pillar thickness had been reduced to approximately 9.7 m. Further management controls were put in place to slow movement of the material and to limit the use of the 9410 tipping level, but this did not alleviate the rate of failure entirely. The results of an initial inelastic numerical model indicated that most of the pillar was damaged and that failure into the decline likely if no changes were made. The numerical modelling predicted that even if material was no longer passing through the ore pass interaction between the voids was unavoidable and would most likely result in instability. The ore pass and plate feeder are an integral part of the haulage system for the remaining life-of-mnie. Two solutions were sought to firstly reinforce and stabilise the pillar between the ore pass and decline and secondly to rehabilitate the ore pass or find an alternate design that could still utilise the plate feeder. This paper summarises the analysis and resulting rehabilitation that was used to accomplish this.

Nov 25, 2010

By Vedala Sastry

Longwall mining for coal extraction in deeper deposits is gaining momentum in India, due to the increasing stripping ratios and depletion of shallow deposits amenable for surface mining. In longwall mining, presence of multiple seams with varying interburden thickness is a major problem especially while planning for over-mining. An investigation program was taken up to analyze the effect of the presence of goaf and virgin coal blocks in already developed and extracted lower seam by bord and pillar mining, on the stress distribution in the longwall panel in upper seam. Studies revealed marginal increase in horizontal and shear stress as longwall face passes above goaf to the virgin area present in lower seam. Stress distribution over chock shields was considerably affected when the face in upper seam reached 15-25m zone above the galleries in the lower seam. A clear influence of the presence of solid coal, galleries and goaf in lower seam was found in the loading of longwall panel in upper seam.

Jan 1, 2007

By Mohammed Sakr

The use of helical piles for permanent foundation applications has become a practical and feasible alternative to the traditional cast-in-place concrete or driven steel piles. Research and development, installation equipment and manufacturing improvements in the helical piling industry have led to this trend. Moreover helical piles are typically smaller in size and weigh less than traditional piles, and require relatively smaller equipment and therefore it is a cost effective option. The latter is a very attractive feature for foundations installed in remote sites across Alaska. This paper presents full-scale pile load test results of helical piles and driven steel pipe piles installed in a site located in Anchorage, Alaska. Four full-scale pile load tests were carried out including two axial compression and two uplift load tests. Both helical piles and driven steel pipe piles were installed and tested at the same site under similar conditions to provide a direct comparison. The results of the full-scale load tests indicate the superior performance of helical piles compared to driven steel pipe piles. This paper describes the pile installation and test setup, presents the test data, and discusses the results.

Jan 1, 2009

Development of Underground Gold Processing Plants Underground gold processing plants have potential advantages over traditional surface installations related to a smaller environmental footprint, reduced capital and mining costs, improved security and increased value of the product delivered to surface. The concept of processing gold ores on the surface is the traditional paradigm. A process of pre-concentration of ore underground is likely to result in a major shift in operating costs. In particular, run of mine ore or a large proportion of it will not need to be transported to the surface. As a result, environmental and financial benefits are likely. Underground plants are likely to be pre-concentration systems where the process product is a high-grade concentrate and tailings for stope backfill. Units will be either static or modular. Concentration methods will be gravity and/or flotation or leach based. This paper discusses the development underground gold plants from early concept, through to the world's first operational unit, a newly commissioned unit and the technical basis of a fully modular system.

Sep 13, 2010

After a five year period representing the strongest resource and commodity rally ever experienced, we are now faced with a subdued recovery following the global financial crisis. This renewed economic growth will be steady but eventually attain levels that reignite export demand out of China and other emerging nations, which are now reliant on increasing domestic demand to support their economies. This backdrop of weaker share prices and less available investment capital creates a greater imperative for company management to ensure that its share price is fully valued. The mining geologist plays an important role in achieving this outcome through direct estimation of asset value (resources) but also in strongly communicating the æupsideÆ value opportunity in both mine site and adjacent brownfields exploration and an efficient and technically sound mining operation. The contribution of mining geologists to assist in conducting analyst site visits should not be underestimated, particularly with reduced analyst coverage of the resources sector and some simplification in company analysis through ranking companies on Reserve and Resource positions.

Jan 1, 2009

By Robert Stefanko

This report, rather than attempting to replace previous annual reports, supplements, and more importantly, coordinates and summarizes the entire effort. Even with such restrictions, the report is voluminous and, therefore, a decision has been made to divide it into two parts. The first volume is basically narrative and includes tabular results and analyses. The second volume is in appendix form giving detailed information. Together, they permit a logical discussion of all aspects of the project (Volume I) without cumbersome distractions but, at the same time, provide all the details to permit others to evaluate and explain the results or develop similar research programs (Volume II). The aim of the original proposal was basically to develop instruments and techniques and then make measurements of suitable power parameters, ground fault currents and ground resistance beds. With such information available, it was possible to develop a meaningful simulator which would permit investigating electrical systems and components on paper without costly trial and error procedures in the third year, a cable splice testing program was added to the project. While there were the usual delays attendant in such original research, these objectives were achieved.

Jan 1, 1973

A rotating disc geometry was used to provide a uniformly accessible surface for a kinetic study of copper cementation with zinc in sulphate solution. For copper concentrations of the order of 10 p.p.m., a porous, adherent deposit is formed on the zinc surface and this has a significant influence on the reaction rate. When the specific mass of deposit is less than about O· 35 mg/cm2 the surface may be considered as smooth and the rate is described by simple convective counter diffusion of zinc and copper ions through a laminar diffusion boundary layer to the deposit-solution interface. In the presence of additional deposit, the diffusional mass transfer rate is increased by increased surface roughness.The rate under these conditions is first order, with the degree of enhancement independent of further increases in the specific deposit mass. The enhancement in rateis, however, directly related to the initial mass flux and the species involved in the reaction.Preliminary work showed the same mechanism to apply to cementation from chloride solution, solutions of high zinc concentration, and cementation of copper with iron..

Jan 1, 1970

By K. Galovich, P. Krivokuca

"Quinsam coal mine is located about 25 km west of Campbell River on the east coast of Vancouver Island, British Columbia. Using continuous miners in a fully mechanized retreat room-and-pillar operation, it produces low sulphur, “super compliance” thermal coal for domestic and international markets at a rate of about 2600 t/d. Currently, 65 people work at the site, including some corporate employees.Opened in 1993, the Quinsam mine had a dismal safety record until 1997. Lost time injuries and medical aids were unacceptably high. In 1998, a change in corporate structure brought a change in safety attitudes; a total and unequivocal commitment to safety as job No.1 by corporate and site management. This commitment was clearly spelled out in a new mission statement, circulated to all employees by the new President and CEO, David Slater: “Safety is job No. 1; Production flows from safety; and Think safety at all times.” As well as re-defining workplace safety practices, QCC tightened engineering controls and enforced strict adherence to mine plans.This paper provides a general background to the mining operation, and describes the safety practices that have resulted in an enviable safety record in recent years, reflected by provincial and national recognition."

Jan 1, 2004

By T DePetris, B B. Beamish

There has been a gradual increase in the volume of internationally traded thermal and coking coal, with emphasis on blending of coals rather than single coal usage. New Zealand can take advantage of this situation, especially with its low ash and sulphur content coals. However, there is a need to clarify the thermal and coking behaviour of these coals as they relate to other market players, to benefit both the consumer and supplier. The high volatile matter contents of New Zealand coking coals are due to their high vitrinite content, which causes them to demonstrate stronger coking properties over a wider rank range than Gondwana coals. These same high vitrinite levels appear to correspond with lower initial softening temperatures than for Gondwana coals of similar rank. Preliminary results using thermogravimetric analysis also suggest that New Zealand high volatile bituminous coals can be used to substitute for higher rank Gondwana coals in combustion processes.

Jan 1, 1994

Much interesting data on cemented carbides has been published over a period of years which, when classified and pieced together, gives a clear picture of this special branch of powder metallurgy. This is an attempt to present the essential information in an ordered account.THE HARD CARBIDES-THEIR PROPERTIES AND PREPARATIONThe so-called hard or refractory carbides are the carbides of a number of metals which are grouped together in the Periodic Classification. These metals are in groups IV, V and VI. They are titanium, vanadium, chromium, zirconium, niobium (columbium), molybdenum, hafnium, tantalum and tungsten. These carbides have attracted the attention of chemists because of their remarkable properties. They possess very high melting points, and are rather difficult to prepare in the pure state. Their outstanding propertyis their extreme hardness, which they share with certain other carbides, such as those of silicon and boron. In addition, these compounds possess distinctly metallic properties, such as lustre (in fused specimens) and high thermal conductivities.(l)t They are capable of forming alloys in two ways:1. With metals, particularly those of the iron group. 2. With each other (a case of solid solubility).The constitution of these substances is not that of ordinary salts, which obey the usual valency rules, but must be likened to that of certain intermetallic compounds. Actually they are "interstitial" compounds(2), that is, they are formed from the ordinary metallic lattice by the insertion of the relatively small carbon atoms in the interstices.. The energy required to fill the lattice completely is high, and this explains the difficulty often found in obtaining the exact stoicheiometric compound. Thus the carbides can have a range of composition, and can be considered as solutions of carbon in the respective metals.Physical Properties of the CarbidesThe hardness of these compounds is so great that it is difficult to compare the individual compounds on this basis. Becker(l) gives values on Moh's scale, which are not very accurate and are of no great value. Burden(3) has reproduced a diagram by Hatfield which indicates that the cemented carbides are between 1,400 and 2,000 on the Vickers diamond scale. However, the pure carbides are harder, tungsten carbide being about 2,200. Hoyt(4) describes a method of measuring hardness applicable to powdered specimenswhereby the powder is rubbed on a standard block of cemented tungsten carbide under standard conditions, and the rate of wear is determined. In...

Jan 1, 1942