Search Documents

By P. E. Hand

Coal is a complex heterogeneous commodity that can be mined in a number of ways and needs to be processed to a homogeneous quality that satisfies the customer?s requirements, while attempting to maximize revenues. Only a small proportion of coal is suitable for metallurgical use. Export coals cover a wide range of qualities and some coals can be used optimally in the raw state for energy production. Critical quality parameters vary and can be a combination of heat value, ash, volatiles, sulphur, phosphorus, sizing, amongst others. The level of beneficiation is generally dictated by the washability of the coal, mining contamination, and the target product quality. The steps in the coal chain covered in this paper comprise exploration, mining selections, production, the washing process, and product delivery. Many points of sampling are needed to maximize yield at the correct quality, and some of these will be described in the paper. Keywords coal chain, coal beneficiation, sampling.

Jan 1, 2014

By J. W. Adams

Measurements of surface magnetic field noise were made at various locations over the Geneva Coal Mine near Price, Utah, on June 12, 1973. The locations selected were on the surface over emergency locator beacons underground at depths between 3S0 meters (1150 ft.) and 488 meters (1600 ft.). The surface terrain where these measurements were made was mountainous, and access was difficult. There were no power lines within several miles, and the weather was clear; therefore, the magnetic noise levels were about as low as will normally occur. Results of measurements of distant sferics indicate rather sharp cutoff frequencies below which broadband, impulsive noise is attenuated. The mechanism of propagation for this noise above the daytime cutoff frequency of 3500 Hz and the nighttime cutoff frequency of 1700 Hz is deduced to be a waveguide formed by the D or F layers of ionosphere as an upper plane and the earth as a lower plane.

Jan 1, 1974

By Maria Fernanda Gonçalves de Oliveira

O objetivo do trabalho é estudar a viabilidade da realização do tratamento superficial via implantação iônica por imersão em plasma (3IP) de nitrogênio de chapas de nióbio soldadas previamente com feixe de laser, para formação de camadas de nitretos sobre superfície do material base, zona termicamente afetada (ZTA) e do cordão de solda. Os resultados obtidos são discutidos levando-se em consideração a influência do tratamento nas alterações apresentadas pelo material tratado. Os resultados mostram uma significativa alteração na superfície do material, em termos de composição química, evidenciando a formação de nitretos de nióbio sobre esta superfície. Em geral, os nitretos de materiais refratários apresentam propriedades desejáveis para aplicações que envolvem temperatura elevadas de trabalho como: estabilidade térmica, elevado ponto de fusão, boa resistência à oxidação; além de apresentarem elevada dureza e baixas taxas de desgaste e corrosão. Em virtude do aquecimento do substrato, durante o tratamento, observam-se mudanças microestruturais no material tratado. Tais alterações microestruturais, nas diferentes regiões analisadas, mostram-se benéficas na homogeneidade dos valores de dureza apresentados, especialmente na região do cordão de solda e material de base. A redução da dispersão dos valores de dureza entre o cordão de solda, a zona termicamente afetada (ZAC) e o material de base podem minimizar a presença de regiões com concentrações de tensões, melhorando a resistência mecânica do material quando submetidos a esforços mecânicos, como tração uniaxial.

Aug 8, 2018

By A. Korchevskiy

While Russia continues to be a worldwide leader in asbestos production, the environmental and health status around Russian asbestos mines is not well known and understood, internationally. A literature review was performed to evaluate the potential impact of Russian mining operations on mesothelioma incidence rates in the Ural region where the majority of the asbestos deposits are located. Asbestos that has been mined in this region includes chrysotile, crocidolite, and anthophyllite forms. The Nicholson-Peto (1986) model was applied to published exposure data and mesothelioma mortality statistics in different cities and villages of the Ural region to estimate mesothelioma potency factors (KM) for the various associated fiber types. It was demonstrated that mesothelioma potency factors, as determined by Berman and Crump (2008), could be used to predict mesothelioma risks of non-occupationally exposed individuals in locations where either pure chrysotile, or both crocidolite and chrysotile, are mined and milled. A mesothelioma potency factor was calculated for anthophyllite that appeared to be higher than expected based on previously published studies. The highest incidence of mesothelioma was identified in a community close to a crocidolite mine. The study confirms the validity of utilizing current risk models for non-occupationally exposed populations near asbestos mining activities where asbestos exposures are relatively low and provides methods of characterizing mesothelioma risk in the former Soviet republics (FSRs).

Feb 27, 2013

By Michael Ostrowski

While the words “explosives” and “blasting” cause insurers to become apprehensive, skilled contractors using modern techniques under controlled conditions rarely cause serious damage or injury. However, blasting operations frequently result in complaints and, consequently, insurance claims. The purpose of this bulletin is to inform construction project participants of some of the measures which may be taken to reduce losses arising from blasting operations.

Jan 1, 2003

By F. E. Lathe

INTRODUCTION THE present study, based largely upon phase equilibrium diagrams and other theoretical considerations but nevertheless addressed primarily to the practical metallurgist, has been undertaken with a view to discovering what light can be thrown upon the role of alumina in slags. According to Liddell (23), "alumina apparently acts as .a base if much silica is present, as an acid if the silica is low, always as a nuisance." Newton and Wilson (26) state that .alumina "is never added intentionally, as it makes the slag viscous, and is generally an undesirable constituent of slags". Camp and Francis (3) sum up their views by saying, "alumina is seldom used intentionally as a flux, but it is present in nearly all raw material, hence unavoidable". One has only to read The Function of Alumina in Slags, by Henrich (I3), and the very extensive discussion that followed the presentation of his paper, to realize that, before the days of phase equilibrium diagrams, it was a very serious question indeed as to whether alumina should be calculated as a basic, acid, or neutral constituent. Opinions then differed widely, as well they might; today, even though no categorical answer can be given to the question raised, the function of alumina can be at least partly clarified by a study of the fundamental work done by the Geophysical Laboratory in Washington and by certain universities in both America and Europe. It will be a source of gratification to Canadian metallurgists and ceramists to know that work of this type is now under way in the recently organized Physical and Crystal Chemistry Section of the Mines Branch, Ottawa, and that results of practical value have in fact already been obtained.

Jan 1, 1951

By J. K. Lemley

The human element in large measure dictates success in contracting relationships. Because of our professional backgrounds, we view contracts primarily as either engineers, contractors or owners. A beneficial contractual environment--one in which decisions, risks and benefits are shared--demands equal consideration of all three points of view. Most of the older cities in the United States, for example, suffer from bad contracts--generalized, patched-together documents that represent an accumulation of modifications originally written to compensate for specific situations that have occurred over the years. Because such documents lack coherence, they often present conflicting instructions which lead to defensive, ultimately destructive attitudes among the parties involved in the day-to-day administration of the project. Good contract development begins with a strong central philosophy to which the details of the contract can be related. First, the owner should establish a comprehensive philosophy in which risks between the parties are identified. Following this, a specific contract document can be written to satisfy this established philosophy. The contrast between two opposed contractual situations, NYC Water Tunnel Number Three and the Seabrook Nuclear Power Plant Cooling Water Tunnels, illustrates how comprehensive, well-written contracts--contracts which share both risks and benefits--provide the basis for achieving quality construction that will reward engineer, contractor and owner.

Jan 1, 1983

By Anastasia M. Suchowerska

The design of effective ground support requires a sound understanding of the pre-mining state of stress in the stratum to be mined. Irregularities in the stress field encountered during multiseam mining are governed primarily by the previous mining in the surrounding strata. The aim of this study is to quantify the effects of rock mass transverse isotropy on the vertical stress redistribution in the rock strata beneath supercritical longwall panels. Wilson?s equations for determining the stress distribution induced in and beyond a single longwall panel after it has been mined have been adopted, and a plane strain finite element analysis of an elastic medium, together with the stress changes predicted by Wilson, was used to calculate the final pre-mining stresses in the underlying strata. Values of the independent shear modulus (G¢) of the rock strata, ranging from 0.1 to 1 times the isotropic shear modulus (Giso) in the plane of the strata, and a Poisson?s ratio (?) of 0.25 have been investigated. The key finding of this study is that the predicted magnitude of vertical stress in the transversely isotropic strata beneath a mined supercritical longwall panel is larger and changes more quickly with horizontal distance than is the case for an isotropic rock mass. This finding is of significance for the design of ground support measures in multi-seam mining operations.

Jan 1, 2012

By Ulf G. Gwildis

The Bright water Conveyance System includes 21 km of tunnels mined by two earth pressure balance Tunnel Boring Machines (TBMs) and two slurry TBMs. The probabilistic baseline approach defined in the Geotechnical Baseline Report (GBR) can representatively be verified by use of a comprehensive tracking system to identify face conditions that allows comparison with the baselines. The glacial geology includes a high lateral variation in soil types that, when combined with the pressurized face tunneling methods, creates challenges for documenting face conditions. Baseline tracking using spoil samples and TBM operational parameters provides information to document actual conditions and support resolution of differing site condition claims.

Results obtained from small scale tests using Australian tin concentrates indicate that metallic tin containing less than 0·1 per cent iron can be recovered by a two-stage process using hydrogen and make-up chlorine. In the first stage the concentrate is ground,. pelletized, roasted, and reacted at 650°C with HCI and H2 to volatilize the tin as SnOI2. The volatilization reaction is conducted with cocurrent gas and solids flow because it was found that the use of cocurrent flow yielded a solids residue substantially free from FeCI2. The second stage uses a technique termed "reflux reduction" during which the SnOl2 produced by volatilization is reduced by hydrogen to form tin and a gas containing HCI and H2 of sufficiently high HCI tenor for recycle to the volatilization stage. The elimination of tin ranged from 98+ to 99·7+ per cent of the tin from concentrates containing 5 to 50 per cent tin, respectively. The process should be capable of continuous operation, and a tentative calculation has shown ,that a treatment rate of 12,000 tonnes of tin concentrate per year could be obtained in a volatilization reactor 1·1 m in diameter and 6·1 m high. The process may have particular application to finely divided concentrates containing less than 20 per cent tin.

Jan 1, 1974

By M. J. Friedel, D. E. Scott, T. J. Williams

Rock masses in deep level mines are subject to high stresses, which can result in unexpected failure of rock into mined-out openings. Historically, various independent methods have been used to discern the causes of rock bursts and to evaluate stress conditions in rock masses susceptible to violent failure. Personnel from two research centers of the former U.S. Bureau of Mines, Spokane and Twin Cities, investigated a rock burst that occurred in May of 1994 in a rock mass between the 4400 and the 4600 levels of the Sunshine Mine, Kellogg, ID. The team evaluated the current state of stress in the pillar and the most likely cause of the rock burst by studying the seismic history of the pillar, examining the geology, analyzing the available in situ stress data, calculating possible fault-plane solutions for the burst, and performing a seismic velocity tomographic survey. The results of the study showed that post-rock-burst seismicity was concentrated about 15 to 30 m west of and about 15 m above the rock-burst location. The pillar is composed of a very hard sericitic-to- vitreous quartzite of a type rarely found in the mine, but that is often found in other district mines having a history of seismic activity. In situ stress analysis of the pillar and the surrounding rock mass showed a probable stress rotation from northwest-southeast to east-west. Of four fault plane solutions, the most probable was either a left-lateral, strike-slip movement with a compressive principal stress oriented nearly north-south, or a right-lateral, strike-slip movement oriented east-west. Finally, tomographic images showed low-velocity areas (interpreted as areas of low stress) associated with the crosscuts and haulageways, and high-velocity areas (interpreted as areas of high stress) associated with the rock-burst location. High velocities were also found in a planar area oriented in an elongate northeast-southwest direction.

By Derek J. Lennon

Ground conditions in central Glasgow generally comprise loose granular deposits overlying stiffer soils. CFA piling would normally be preferred for urban sites in these ground conditions, but flighting of the superficial deposits has on occasions resulted in building damage. Over the last five years rotary bored piling with vinyl polymer support fluid has proved to be an economic alternative to bentonite slurry. Two case histories in central Glasgow are described in this paper, one for piles founding in granular soils and one for piles founding into bedrock. A comparison is made between the methods required for disposal of the liquid waste from bentonite and vinyl polymer slurries.

Jan 1, 2006

By Mike McWha

Drivers to increasing RM use ?Compliance issues ?Section 12 JSE Listing Rules ?Canadian NI 43-101 ?Sarbanes Oxley ?Shortage of African ore reference materials ?Poor perceptions about quality of some local RM?s

Jan 1, 2005

By Víctor De la Cruz

Dado que la mina Rosaura (Lima) se dedica a la explotación de minerales polimetálicos como el zinc, plomo, cobre y plata, la caracterización geomecánica de su estructura, morfología y reservas demostró una tendencia hacia los métodos masivos -en tanto presenta ventajas técnico-económicas comparativas frente a otros posibles métodos como el corte y relleno y conjunto de cuadros. Por ello, el presente texto describe el método de “Hundimiento por Subniveles” (Sub Level Caving – SLC), como el más indicado. El SLC se basa en la utilización del flujo gravitacional del mineral fragmentado a través de la perforación, voladura, y el hundimiento de la roca estéril principalmente de la caja techo. El diseño del elipsoide de extracción determinará la ubicación de los Sub niveles y Drawpoints, los cuales serán críticos para hacer rentable el minado, de forma que los beneficios actuales del método indican niveles altos de Seguridad, recuperación alta de mineral, bajos costos y mejora constante de la productividad.

Sep 9, 2007

By W. J. Miles

Many years ago, a relationship was established between dust inhalation and pneumoconiosis. Since then, various government agencies have regulated crystalline and amorphous forms of silica material in the workplace. In 1987, the International Agency for Research on Cancer (IARC) classified crystalline silica as a probable carcinogen. With this listing, crystalline silica became a regulated substance under the Hazard Communication Standard. The minerals and chemicals industries have responded in various ways. They have: • developed worker and user training programs and literature; • labeled products with appropriate warnings; • continued to implement dust reduction programs; and • developed meaningful epidemiological studies of workers. • begun development of reliable analytical methods for measuring crystalline silica at the 0.1 % threshold level; Background Silicosis historically has been the major health hazard resulting from exposure to crystalline silica. Silicosis is the scarring of the lung from excessive exposure to crystalline silica. It has been recognized as an occupational disease for more than 2000 years, since early Greek physicians noted the respiratory problems of miners, stonecutters, and quarrymen who were exposed to excessive quantities of mineral dust. During the industrial revolution, the incidence of the disease was greatly increased by the use of machinery that increased dust levels. Subsequently, the need for dust control was recognized and measures were instituted. Silicosis is characterized by progressive breathlessness on exertion and develops over the course of years. Xray images of the lungs show

Jan 1, 1990

This paper details a brief history of the Australian gold industry from the 1980s gold boom to the present day, highlighting an industry characterised by innovation in plant design and junior companies prepared to "have a go", in contrast to the conservatism of many larger mining companies. Design flexibility, the innovation of new processes, the preparedness to exchange "process know how" and technology singularly differentiated the gold industry from other sectors during the 1980s to the present. The introduction of two stage crushing, semi autogenous (SAG) milling, and pebble crushing, mill innovations, carbon in pulp (CIP) and carbon in leach (CIL) and the North Kalgoorlie screen etc were all exciting changes in the industry.

Jan 1, 2011

By G. Pan

The production data of many mines have not reconciled geostatistical estimations based on exploration and development drilling. The discrepancies in recovered metals are sometimes as large as 30%. A number of factors are responsible for such unpleasant outcomes. A major cause, however, is the lack of geological controls in the implementation of geostatistical techniques. Geological modeling establishes geological constraints and mineralization/ore envelopes. Geological constraints are usually established through drill hole interpretation. Mineralization and ore envelopes have been delineated manually based on assay grades. The issues associated with manual methods are: •Time requirements . •Inconsistent dilution. •Uncontrollable implementation variance. Although the time issue may not be a big concern for some companies, the other two have been responsible for many undesired estimation errors. A new geostatistical approach described in this study is designed on the basis of indicator and ordinary kriging. The central component of the method is the procedure for automatic delineation of mineralization and ore envelopes. The method, referred to as probability assigned constrained kriging (PACK), is demonstrated on a Carlin-type gold deposit. The estimation results are compared to blast-hole based production panels, showing that the estimated tonnage is about 2.1 % higher than the actual production, and the average grade is about 2.4% lower.

Jan 1, 1995

Cobalt/tungsten mineralization at Mt. Cobalt, located 170 km southeast of Mt. Isa in northwestern Queensland, is described. Mineralization occurs in the Kuridala Formation of the Mary Kathleen Group, which is composed dominantly of pelitic schists, carbonates and acid and basic volcanics.Rocks in the region are metamorphosed to amphibolite facies and affected by two generations of tight to isoclinal folds and a third, more open generation of folds. The region is divided into three meridionally trending belts on the basis of structural style, with mineralization concentrated in the central, more highly strained belt.Deformation and metamorphism is probably younger than 1670 m.a., and the rocks are intruded by granitic rocks dated at 1509 ± 22 m.a.Mineralization occurs in shear zones at the contact between an amphibolite and enclosing pelitic schists, and within the amphibolite itself. Mineralization consists of cobaltite and scheelite with lesser chalcopyrite, pyrite, pyrrhotite, i1menite, allanite, xenotime and apatite. The mineralizing event involved addition of K, Cl, CO2 W, As, Cu, Ni, Au and rare earths and depletion of Ca and Na. It altered a hornblendeandesine/labradorite host assemblage to a biotiteoligoclase/andesine-scapolite assemblage. Though tourmalinealteration also occurs, it is probably not related to mineralization.It is concluded that the mineralization and alteration assemblages formed by reaction of saline fluids with amphibolite close to the peak of amphibolite facies metamorphism.The fluids are probably metamorphically derived, and their movement was channelled through high strain zones in the sequence. The material carried by the fluids was derived from the metasedimentary/metavolcanic pile as a whole.Other deposits in the Mt. Cobalt-Selwyn area have characteristics comparable with Mt. Cobalt, and the mechanism for the genesis of Mt. Cobalt may have applications at other areas in the region.

Jan 1, 1983

By S. L. Windes

This report presents physical and petrographic properties of approximately 60 types of rock from operating mines or mineral-investigation projects and supplements Repot of Investigations 4459, Physical Properties of Mine Rock (hereinafter referred to as Part I). The physical properties evaluated include the following: Apparent specific gravity Apparent porosity Compressive strength Flexural strength (modulus of rupture) Impact touchiness Abrasion hardness Scleroscope hardness Modulus of elasticity (Yourg?s modulus) Modulus of rigidity Specific damping capacity Longitudinal bar velocity

Jan 1, 1950

By D. Nag, J. Fernando

Hazelwood Power Mine is one of the largest open pit brown coal mines in Australia. The removal of overburden is the first step in coal winning operation. The primary aim of construction of overburden dump is to provide an effective stable working surface for stacker. The paper discusses site investigation techniques used to determine dump soil properties, stability analysis method using GALENA and GWEDGEM, results of stability analysis. The paper concludes with recommendation for a safe dumping strategy for level 2 stacker dumping.

Jan 1, 2003