Search Documents

By A. J. Forney

The hot-gas-recycle process, for the hydrogenation of carbon monoxide, was investigated in a 12-inch-diameter reactor. Initially because the distribution of gas was poor, hotspots developed in the catalyst bed. After the velocity profile of the gas flowing through the bed was studied, the method of packing the catalyst was altered. Because this change improved the distribution of gas, temperature control was excellent. The l2-inch-diameter reactor was operated successfully in the synthesis of gaseous and liquid fuels. When high-Btu gas was synthesized in two stages, parallel-plate assemblies of Raney nickel were almost as active as granular Raney nickel in the second reactor. The pressure drop through the second reactor, however, was reduced 90 percent by the use of these assemblies.

Jan 1, 1962

By Marco Vinicio Guamán Alarcón

O modelo do Gradiente de Tensão (SG) e a Teoria da Distância Crítica (TCD) são usados para estimar o limite de fadiga de corpos de prova com entalhes alongados, e essas estimativas são testadas em C(T) modificados submetidos a tensões cíclicas de amplitude constante com uma razão de tensão R = 0.1. Os valores medidos são comparados com as previsões feitas por ambos os modelos. As previsões do modelo SG estiveram mais de acordo com os resultados experimentais. Também foi demonstrado que o modelo SG é quase equivalente à TCD no caso de entalhes com raios grandes, quando a TCD usa o método do ponto. Para o caso de entalhes afiados, os valores dos limites de fadiga previstos pela TCD são mais conservativos que os previstos pelo modelo SG.

Aug 17, 2017

By C. H. Fisher

Coal carbonization, the basis of a major industry, consists in heating coal in the absence of air at various temperatures (ranging from 500° to 1,000° C.) that are selected according to the kind of products desired. During this treatment, the complex organic substances that comprise the major part of the coal are converted into several useful products that are quite different from the original material. The principal products of coal carbonization or distillation are coke and gas. These products, as well as others of which lower yields are obtained (light oil, tar, and ammonia), occupy an important place in present-day commerce and civilization. This paper is concerned with the composition of the tar and light oil, which, as complex mixtures of organic compounds, are the source of many important dyes, inter-mediates, medicinals, resins, etc. The volatile products obtained when bituminous coals are destructively distilled or carbonized are tar, aqueous liquor, and gas. These products vary in composition and properties, depending on the nature of the coal and the temperature and conditions of carbonization. The tar is a dark, rather thick and viscous liquid at ordinary temperatures, becoming semisolid when cooled to the freezing point of water. The aqueous liquor (chiefly water) contains several inorganic substances and certain organic compounds, which, because of their solubility characteristics, have been extracted from the tar. The carbonization gases consist chiefly of carbon dioxide, carbon monoxide, hydrogen, hydrogen sulphide, ammonia, methane, ethane, ethylene, and several hydrocarbons of higher molecular weight. The hydrocarbons of higher molecular weight (benzene, toluene, xylene, etc.) may be re-moved as liquids from the gas by suitable means. This liquid and the first fractions obtained on distilling the tar are known as light oil.

Jan 1, 1938

By WM. H. RINKENBACH, C. A. Taylor

No complete work on explosives, their constitution and analysis, has hitherto been published. Several books that contain chapte.r;s on analysis do not cover the matter thoroughly. Methods tha;t, manu~ facturers, testing stations, and other . agencies have developed to meet their own requirements have not been made public. The Bureau of Mines has issued four publications 1 - cov:eri:ng special phases of the subject. This bulletin. is not inte.nded to replace those reports, but rather to cover present methods employed 'in the , industry and to include all classes of explosives and the materials used in their manufacture. No sharp distinctions can be drawn between classes of explosives. . Surplus military explosives, for example, may be used for blasting, just as blasting explosives, under some conditions, may be employed for military purposes. Moreover, one class gradually merges into another because of similarity in composition. Explosives are here grouped as dynamites, black powders, propellants, detonators, and primers. Some materials are used in practically all these groups ; others in only one. To discuss all the materials that have been or that may be used and the methods for their identification and quantitative determination is not feasible, but the methods described will probably suggest ways of examining new mixtures.

Jan 1, 1923

By D. A. Greenwood

Dr David Greenwood opened the first technical session of the conference by highlighting the diverse nature of the papers in this session but drawing attention to the common theme that each solved a particular problem. PAPER 1.1 Tony Elliott introduced his paper on deep mix-in-place soil/cement stabilisation by stressing its simplicity. The engineering solution adopted at Elland was detailed in his paper and had formed the key to success of the project. The process itself is not widely used or known in the UK, although it has the potential to achieve significant benefits, subject to proper engineering control being exercised. It was explained that although the concept was not new, development of the technique for soil modification was relatively recent. The alternatives to mechanical mixing are injection, which is very dependent on soil type, site geometry, etc, and jet grouting; both processes are soil-responsive, and not easily monitored or programmed, difficulties which can largely be overcome by mixing. To achieve this at depths to say 30m requires high-powered, high torque machines and has resulted in significant equipment development.

Jan 1, 1991

By Pullen G, Rose M

Continuing Professional Development (CPD) is not just a catch-cry. It is an essential component of every-day life in many professions, including accountancy, law and public administration. Without realising it, many other professions are undertaking CPD activities in an un-structured way, including mining, metallurgy and geology. Examples include Annual and technical conferences of The Institute, Branch-level technical meetings and in-company training and development programmes and technical exchanges. Whilst approaches to date have undoubtedly helped keep the Australian mining industry at the forefront of mining technology, one cannot presume that technological development will stand still. To meet this challenge, human resource development must keep pace, not only to optimize utilization of technological developments, but more importantly to develop firm bases from which new products, processes and technologies can be developed within Australia.

Jan 1, 1989

By Ott F. Heizer

The mines and the mill of the Nevada-Massachusetts Co. are on the east slope of the Eugene Mountains, in Pershing County, Nevada, 8 miles northwest of Mill City, a station on the Southern Pacific R.R. and on the Victory Highway. Fig. 1. Supplies and, concentrate are transported by truck over an automobile road of easy grade. The property is at an average elevation of 5500 ft. and climatic conditions are generally favorable for continuous operation throughout the year. The ore treated is supplied by two adjoining mines, the Stank and the Humboldt. Physical and mineral characteristics of the ores produced by these two mines are substantially similar, although variations occur in hardness and mineral distribution.' The economic mineral is scheelite (CaWO4), composed, when pure, of 80.6 per cent tungstic trioxide (WO3) and 19.4 per cent lime (CaO).

Jan 1, 1935

By D. F. Malan

In deep level hard rock mining the rheological behaviour of the rock is important as time-dependent aseismic processes can lead to a stable dissipation of energy thus reducing violent outbursts. Underground closure measurements, observations of time-dependent fracture formation and siesmic data indicate that the rock in deep South African gold mines shows significant time-dependent behaviour. The objective of this work is to quantify the time-dependent rock behaviour for laboratory specimens and underground conditions. Laboratory experiments indicated that lava and quartzite specimens undergo measurable creep strain at stress magnitudes below the failure stress. Quartzite is however prone to more significant creep at lower stress levels. A viscoelastic analysis showed that laboratory creep results can not fully explain the behaviour observed underground. The in situ behaviour is governed mainly by the rheological behaviour of the fracture zone and the resulting time-dependent formation of new fractures. A viscoplastic discontinuity model implemented in a boundary element program is used to simulate this behaviour.

Jan 1, 1997

By David S. Yang, Osamu Taki

The innovative Soil-Cement Mixing Wall Technique, developed independently in Japan, consists of mixing in-place soils with cement grout using multi-axis augers and mixing paddles to construct overlapping soil-cement columns. The applications of overlapped soil-cement columns include cutoff walls for groundwater control and structural diaphragm walls for excavation support. The special features of this technique include water tightness, versatile strength design, and efficient installation in subsurface materials varying from clayey soils to cobbles or soft rocks. Through the introduction of two recent subway projects in Japan, this paper presents the design parameters, construction procedure, quality control and performance of soil-cement wall for excavation support and groundwater control.

Jan 1, 1989

By H. Y. Sohn, R. D. Hagni, M. K. Kojo

Reflected light microscopy was used to study the mineralogy and textures of experimental reactions of a nickel concentrate with a slag. Such an interaction is an important step in the bath smelting of nickel sulfide concentrate. Concentrate particles in the central portions of the pellets are rounded and develop vermicular SO2 gas porosity. In the outer portions of the pellets, the original minerals of the concentrate, pyrrhotite, pentlandite, pyrite, chalcopyrite, and violarite have agglomerated and reacted to form two intergrown phases: 1) pyrrhotite solid solution (Fe0.75Ni0.18Cu0.01S) and pentlandite solid solution (Fe0.58Ni0.51Cu0.03S). Magnetite formed euhedral crystals, skeletal crystals, and dendrites at the margins of the matte. Prismatic ferrohypersthene and octahedral Mg-Al-Fe spinel crystals and dendrites are present in the glassy slag.

Jan 1, 2001

The commercial development of the shallow (2200 ft2 400 ft) Windalia sand reservoir at Barrow Island provided the opportunity to conduct an intensive drilling programme using equipment and techniques designed for optimum performance.During the initial exploratory and reservoir delineation phase, 12 specific Windalia test wells were drilled using drilling equipment with an optimum depth range of 6QOO ft - 8000 ft and a 9 5/8 in by 7 in. casing programme was employed. The average time from commencement of move-in to rig release exclusive of coring for five representative wells was 187 hr during this phase.Development drilling commenced December 1966 with one rig, with the second in operation January 1967.As of January 1 1968, 168 development wells had been completed. The two rigs employed are drive-in units equipped with a telescoping .gelf raising doubles mast.Optimum depth range with 4 1/2 in. drill pipe is 2500-4000 ft. Casing programme is 8 5/8 in. by 5 1/2 in. Efficient performance was achieved immediately. The average time from commencement of move-in to rig release for 15 wells drilled early in the development programme was 99 hr.By application of experience and further modification of techniques, performance was improved to an average time of 72 hr per well for 15 wells recently completed.The major drilling problem on Barrow Island is surface hole drilling due to the very hard surface limestone combined with complete loss of circulation at sea level.In this operation, significant improvements have been effected. During the exploratory phase drilling, 12 1/4 in hole to set 9 5/8 in. casing, average penetration rate was 23 ft/hr. At the commencement of the development programme penetration rate, drilling 10 5/8 in. hole to set 8 5/8 in. casing, was 28 ft/hr for the 15 early wells considered, improving to 55 ft/hr for the 15 recent wells considered.This programme is a team effort and much credit must be given to the enthusiastic co-operation of the two drilling contractors.The current field record is 2 days 4 hr with a 4 1/2 hr move including the drilling of mousehole and rathole.

Jan 1, 1968

By Jacob Chacko

The east span of the San Francisco-Oakland Bay Bridge (SFOBB), which is one of the most heavily traveled bridges in the world, will be replaced due to seismic safety concerns. The majority of the new bridge will be founded on large-diameter (1.8 to 2.5 meters), approximately 60- to 100-meter-long pile foundations The large-diameter steel pipe piles and soil conditions are similar to those used/encountered in many offshore structures. Thus, the design methods used are based on site-specific modifications to the procedures recommended by the American Petroleum Institute rather than the conventional procedures that have been formulated and used for the design of much smaller piles. Pile foundations will experience their maximum loads during the design earthquake. For the Safety Evaluation Earthquake, tension loads of up to approximately 80 to 90 meganewtons (MN) and compression loads of up to approximately 120 to 140 MN were calculated. Due to the economic importance of the SFOBB and the consequences of catastrophic failure in both economic and human terms, the design and analysis of the pile foundations supporting the bridge consider a number of aspects of pile-soil behavior that are normally ignored. Those aspects include: 1) the effects of consolidation and setup, 2) the behavior under dynamic loading, 3) the losses of resistance under cyclic loading, and 4) the load-settlement behavior of the piles under severe cyclic loading conditions. Since the treatment of complex aspects of pile foundation behavior is not codified in any guiding documents, several project-specific methods were developed for design and analysis of the foundation piles.

Jan 1, 2002

By Jeffiey B. Austin, Maurice Tagami

"The ores of the Iberian Pynte Belt are typically massive sulphide ores with very fine grained mineral textures. EuroZinc Mining Corporation is currently evaluating one of the massive sulphide deposits located near the town of Aljustrel, in South Central Portugal. The deposit contains significant grades of lead, zinc and silver. The ores are comprised solely of sulphide mineralization consisting of pyrite, sphalerite, galena and some secondary copper minerals. Liberation requirements for these ores are typically 22 to 25 microns. A selective flotation process has been utilized to produce separate lead and zinc concentrates for sale to off-site contract smelters.This paper outlines the process test results and describes the process parameters required to optimize the process parameters. Ths test program has been conducted in support of the re-opening of the facilities in Aljustrel. The 3500 tpd mining and milling facility was commissioned in 1990 and operated for 18 months before closing. The previous facility was designed to produce three products using a selective copper-lead-zinc flotation process. EuroZinc Mining Corporation is proposing to re-open the operation, selectively mining from a lead-zinc phase of the massive sulphide deposit and produce only lead and zinc concentrates.Results are presented and discussed.PROJECT HISTORY AND CURRENT PROJECT OBJECTIVESThe EuroZinc Aljustrel Project is a potential major producer of lead, zinc and silver located in the Iberian Pyrite belt of south-central Portugal. The town of Aljustrel is historically associated with mining dating to the time of the Romans. The area is rich in pyrite deposits, and sections of the pyrite deposits contain significant zones of copper, lead, zinc and silver. Mining in Aljustrel during the last century (1900’s) included a major pyrite mining operation, which produced feed for sulphuric acid production. Pynte mining operated from the 1930’s to the early 1970’s and a short-lived base metal operation from 1989 to 199 1."

Jan 1, 2000

By T. Field, N. D. Nxumalo

Since the discovery of gold on the Witwatersrand in 1886, mining has been at the centre of South Africa’s development. Although mining continues to contribute significantly to the country’s economy, it is a temporary land-use activity, and mine closure is inevitable. This paper reviews mine closure planning at Tshikondeni coal mine, which commenced in 2014 with the initiation of mine closure. The review presents the mine closure processes undertaken at the Tshikondeni coal mine as regulated by South Africa’s principal mining legislation, the Mineral and Petroleum Resources Development Act 28 of 2002, and other relevant regulatory frameworks. To compile this review: (1) A desktop study was conducted; (2) empirical data was collected through one-on-one interviews with research participants at Tshikondeni coal mine; and 3) physical observations were made of the rehabilitation at various mine operations within the Tshikondeni coal mine complex. Research participants consisted of mine officials from different departments, i.e., human resources, and environmental, social, and business strategy, who were directly involved with the Tshikondeni coal mine closure. A questionnaire with semi-structured questions was developed. It was utilised to acquire a better understanding of mine closure planning at Tshikondeni coal mine and identify mine closure processes that aim to achieve post-mining land uses and align with Tshikondeni coal mine’s post-closure strategy, namely the Tshikondeni Legacy Project, with a post-closure strategy that has the potential to transition a mining economy to an eco-tourism economy that can preserve livelihoods and selfreliant communities.

Dec 15, 2025

By R. G. Reddy

Reduction of different chromite ores with carbon was studied as a function of C/FeO ratio and temperature in the range 700 °C to 1100 °C by thermogravimetry (TGA) analysis. Powders of chromite ore(-150 mesh) and carbon(-150 mesh) were thoroughly mixed in a desired proportions and were placed in the reaction crucible. The reduction rates of reactions were determined by continuously monitoring the weight loss as a function of time at constant temperature using TGA set up. The analysis of results suggest that FeO present in the chromite ores is reduced to Fe involving gaseous intermediates CO and CO2. The overall rate of FeO reduction is controlled by the oxidation of carbon. A kinetic equation, that of random nucleation, was proposed. The activation energies for the reduction of FeO, present in Roast Movat and Transvaal ores, with carbon were determined to be 55800 and 23000 J/mole, respectively. The results of the present study are compared with the data available in literature. The low activation energy values as determined in this study suggest that the carbon oxidation reaction is catalyzed. It is concluded from the present investigation that the low grade chromite ores can be significantly upgraded to higher value added chromite that can be used as a feed source for economical smelting.

Jan 1, 1998

By K. Lundholm, M. Andersson, L. Nevatalo, Å. Holmström, L. Hedström

"Several copper deposits have the arsenic bearing minerals enargite (Cu3AsS4) and tennantite (Cu12As4S12). Since this mineral contain both arsenic and copper, it is not possible to remove the arsenic by selective flotation. Partial roasting is a method to clean the concentrate from arsenic and thereby produce a suitable raw material for the copper smelter. Also mercury is commonly found in copper bearing minerals. In the partial roasting process both arsenic and mercury are volatilized, while part of the sulphur is used as energy during the roasting. This gives a calcine suitable as feed to a smelter, much like an ordinary copper concentrate. A typical analysis of calcine would be: S content 18–22%, As content below 0.3%, Cu content – not affected, grain size – not affected. However, if the concentrate contains mercury, the mercury will be volatilized during the roasting process. This will lead to very high mercury contents in the subsequent process of sulphuric acid, unless the SO2-rich process gas is pre-treated by the Boliden/Norzink process that recovers mercury as calomel, Hg2Cl2. The volatilized arsenic in the gas phase can be recovered either by dry or wet methods. However, one problem is that arsenic also contaminates the fine grained calcine dust that is captured downstream in the gas cleaning system. The calcine dust contains valuable metals such as copper, gold and silver that needs to be separated from the arsenic. The ultimate aim is to stabilize the recovered arsenic as a compound with minimum impact on the environment and recover the valuable metals. By using wet recovery methods it is possible to selectively precipitate copper, gold and silver as sulphides while arsenic is kept dissolved in the liquid. The precipitated metal sulphides can be mixed with the calcine and sent to the copper smelter. The dissolved arsenic is sent to effluent treatment and is further treated in Outotec ferric arsenate precipitation process, where arsenic is precipitated as the stable compound basic ferric arsenate, formula FeAsO4·xFe(OH)3. All concentrates containing arsenic are unique and the process design of a roaster plant must be based on relevant process data. The process data is collected during tests in lab scale and pilot scale, where the influence of critical process parameters on the quality of calcine is studied. The ability to run tests both in lab scale and pilot scale is crucial to the development of the correct roasting process. Outotec is well equipped for this."

Jan 1, 2014

By G. W. Center

This manual is intended to assist federal, state, and local regulatory and planning agencies, the mining industry and consulting engineers in determining the regulatory, environmental, technical and economic constraints influencing the site selection, planning, construction/operation and reclamation phases of a waste disposal facility. The information presented illustrates that factors affecting an individual site may be simple or very complex. This manual discusses methods for making future land use decisions, determining regulatory requirements, evaluating physical, chemical and structural properties of the disposed waste and selecting appropriate waste disposal methods and control techniques. Procedures and guides in the manual will assist personnel in assessing the complexities of waste disposal on a site specific basis. The major types of waste disposal systems are discussed and evaluated in terms of their advantages and disadvantages and applicability to varying site conditions and waste characteristics. Appropriate references following each chapter provide more detailed data on material presented in the text.

Jan 1, 1982

By Y. Wang

China is a big mining country with a long mining tradition and history. At present, there are nearly 200,000 different mines and 21 million workers. The total production value of mining makes up 6% of GNP. With the development of economy, the mining industry has played a more important role in our economic market, supplying more than 95% non-reusable energy, 85% of industrial and agricultural raw materials, over 75% of fertilizers and 30% industrial and agricultural water.

Jan 1, 2001

By T. C. Wesson

The need for elemental-analysis information on coal mine dust for use in health and safety research prompted this study by the Bureau of Mines. Neutron-activation and X-ray fluorescent techniques were used to obtain five-element analysis (silicon, aluminum, iron, calcium, and magnesium) on 444 samples from 68 coal mines in 10 States. From these analyses, the average composition of the dust in coal mines was determined. The contribution of the primary dusting material (limestone dust) to the makeup of coal mines was shown. Regional differences in mine-dust composition were indicated.

Jan 1, 1974

The following paper describes the refining practice for the production of lead, silver and gold at the works of The Broken Hill Associated Smelters Pty. Ltd., Port Pirie, South Australia.The refinery is situated on the wharf frontage and is built parallel with it. The refinery occupies an area of approximately 3380 square yards. (Fig. 8)There are two buildings, one containing the softening and de-silverising sections, measuring 225 ft. x 57t ft., while the other building, which measures 225 ft. x 90 ft. covers the de-zincing, lead moulding, retorting, cupellation, and dore parting sections. (Fig. 1)The retorting, cupellation, and dore parting sections are completely isolated from the rest of the plant by strong small-mesh wire gratings welded to steel uprights. The dore parting plant and generator room are further isolated by a brick wall, built up to the roof. The two main buildings are steel structures, with outer walls and roof of "Robertson" corrugated sheeting; the side and end walls are open for some distance above the ground, and this, coupled with the high roof which is 50 ft. from ground level, ensures the free access of air and light. Conditions are such that operators work in a clear atmosphere.

Jan 1, 1937