Search Documents

An assessment of methods currently available for the accurate determination of low concentrations of platinum in ores and mineral concentrates indicated that prior treatment of the sample by fire assay procedures is necessary. To enable rapid determinations to be carried out, instrumental methods applied to the metallic bead produced from the fire assay treatment have been evaluated, considering maximum flexibility for concentration variations, minimum chemical operations, and adequate sensitivity.Atomic absorption spectrometry proved suitable, giving solution determination limits of 0·4 p.p.m. Pt, 0·1 p.p.m. Pt, or 0·06 p.p.m. Pt under various extraction conditions using aqueous and organic agents. Thesedetermination limits related to 1 assay ton of sample (32·67 g) produced easily readable and accurate readings within the range of platinum contents (0·03-2·0 p.p.m.) of economic interest in deposit evaluation and prospecting. The technique shows promise of also being suitable for determination of palladium and gold.

Jan 1, 1970

The El Pe±on gold-silver deposit comprises four epithermal, low-sulfidation veins, which contain 2.9 million oz Au and 48 million oz Ag. Provisional data on alteration mineralogy, fluid inclusions, and vein textures constrain the chemistry and hydrology of the hydrothermal system responsible for ore mineralisation at El Pe±on. Alteration minerals include quartz, adularia, albite, illite, smectite, calcite, chlorite, and pyrite. Alteration minerals suggest the existence of near neutral pH, low salinity hydrothermal fluids, which circulated over an area greater than 18 km2. Complex mineral zonation patterns result from variations in host rock permeability and composition, overprinting alteration possibly produced by thermal waters from surficial and peripheral parts of the hydrothermal system, and supergene weathering in the hyperarid environment. Upflow zones were focused along N-S and NE trending structures, producing crustiform quartz-adularia+carbonate veins. Fluid inclusion data indicate vein deposition from low salinity (

Jan 1, 2002

By Solomons S. S, Tillmann V. H

The progress of longhole open stoping (LHOS) at Zinc Corporation Limited and New Broken Hill Consolidated Limited (ZC/NBIIC) is described together with the design of a novel sloped wall longhole stoping method which should allow the complete extraction of the orebody without the formation of pillars and with minimal dilution of the ore with sand fill.

Jan 1, 1981

In redesigning the cyanide plant at Mount Torrens, in conjunction with Mr. L. W. Grayson, the manager, several minor alterations were introduced in order to have the operations under thorough control, and these having proved serviceable may be of sufficient interest to merit a description here. The lixiviation vats, though only 8 feet in diameter, were retained, but the pipes leading away from the bottom were reduced from two inches to half-an-inch in diameter, and had a fall to the zinc boxes of about 4 feet. As these small pipes were completely filled by the solutions fiowing away from the vats, they exerted a suction equal to their fall and thus hastened the rate of flow, so that tailings containing a larger proportion of slimes could be treated than was possible where the larger pipes were used, as, there not being sufficient fiow of solution to keep the latter filled, no suction could be obtained with them. It was found that with'most of the tailings treated a sufficient flow could be obtained from the half-inch pipes when the taps on, them were only one-third to half open. The lower end of each of these pipes was connected by means on indiarubber tubing with the sille hole of 11 in aspirator bottle, and to the mouth of this bottle a few feet of similar tubing was connected, so that the solutions coming through could be directed into either of the fixed tubes leading respectively to the waste water tank the strong solution zinc boxes or the weak solution zinc boxes.In working the vats, the following method was found to give good results. While filling the vats with tailings the taps were left open, so that the water might drain off into the waste water tank the surface of the tailings was carefully levelled. When the strong solution was run in at the top, the air contained in the interstices of the tailings was forced through the half-inch pipe at the bottom as a strong blast, instead of, as I believe js usual, escaping by means of channels formed by it through the tailings, and thus tending, it would appeal, to render the disposition of the tailings less even and to make.

For tax purposes a mining company is a New Zealand company whose principal source of income is from the business of mining, or exploring for certain specified minerals in New Zealand. New Zealand tax law distinguishes between a non-resident mining operator and a mining company, with the only major difference in tax treatment being the corporate tax rates. New Zealand mining companies are taxed at 28 per cent, whereas non-resident mining operators are taxed at 33 per cent of taxable income. These provisions also apply to the petroleum mining industry. Individuals who carry on the business of mining are also specifically defined in the Act. They are termed as 'resident mining operators'. Non-resident mining operators are non-residents of New Zealand who carry on mining ventures as a business in New Zealand. Mining ventures are defined as the exploring, searching and mining of specified minerals, including development work carried out for profits. Similar provisions apply to the petroleum mining sector. Specified minerals are defined in the Income Tax Act 1976 ('the Act') and while no useful purpose is obtained by listing them in the paper, they include a larger number of industrial and commercial minerals. The Minister of Finance is also empowered to add to the list by publishing his determination in the Gazette.

Jan 1, 1988

The mining industry continues to be a major driver of the Australian economy generating over A$130 billion in export earnings in 2008/2009. However, the industry has been cited as a significant contributor to green house gas emissions. Australia's proposed carbon trading scheme, the Carbon Pollution Reduction Scheme (CPRS) will financially impact on mining operations; this calls for a holistic planning approach for mining operations taking into account the impact of the emissions trading scheme. Since carbon trading is a new area of study, particularly within Australia, the quantitative effect of the CPRS on the mining industry is uncertain and current mine planning practices do not directly consider emissions. This paper presents results of the study into the impact of the CPRS on a hypothetical large scale open pit operation, using a spreadsheet model based on linear programming and simulation. By varying the production rates, life of mine (LOM), carbon price and ore grades among other variables several scenarios were simulated to determine the impact of emissions trading scheme on the net present value of the project. This study found that the adoption of the proposed Carbon Pollution Reduction Scheme could impact mining operations in Australia by a three per cent to six per cent reduction in net present value, for carbon credit costs of $25/t to $50/t respectively. While the six per cent reduction in net present value for a mining operation is significant, rising fuel prices have had a similar effect in recent years. The most energy-intensive processes are the milling circuit and the flotation concentrator circuit. These processes are jointly responsible for up to 60 per cent of the total emissions, depending on the production rate and the level of offshore processing conducted. Clearly, the introduction of the CPRS makes it is imperative for mining companies to assess the impact of carbon emissions on a mining project during mine planning.

Dec 6, 2010

The reactions between molten aluminium and cryoIite have been determined from a material balance of all components involved in the process. The interpretation of results were supported by x-ray diffraction studies of the evolved vapours, quenched electrolyte samples, and side-reaction products.The most important reaction involves the formation of both Na2F (sodium subfluoride) and chiolite in the fused electrolyte. The Na2F accelerates vaporization of the melt. Some AIF (aluminium monofluoride) may also be formed but the proportion of this is much less than for the former subvalent compound.

Jan 1, 1968

The title of this address was selected before I had an opportunity to consider in detail the matters that I would like to discuss. Accordingly, I chose a very broad subject-so broad indeed that it would be foolhardy for me to attempt to deal with more than a few aspects of it. I do not propose to touch. at all on the developments to date of our mining and metallurgical enterprises, beyond paying a sincere tribute'to the skill and enterprise of those who have established an international reputation for Australian mining and metallurgy. I would rather look ahead and discuss certain factors that will play a decisive part in the future development of our mineral resources. I do this in no dogmatic spirit, and I hope that my remarks may lead to discussions which will stimulate action where it is needed.In recent years my colleagues and I have been forced by circumstances to give consideration to problems in the fields of mining and geology, and in process metallurgy, which lie outside the scope of our own research work. People come to us with metallurgical problems because they know of no more appropriate place to go, and it is distressing to have to inform them that it is nobody's job to offer them advice and assistance. I want to suggest to your Institute that it should press strongly for the provision of properresearch facilities for the mining and metallurgical industries, such as aready exist in most enlightened countries. In such countries, those connected with the development of mineral resources are able to obtain information and advice from Geological Surveys, Mines Departments or Bureaux of Mines, which offer far more comprehensive services than are available in this country.Before discussing specific technical problems of the mining and minerals industries, I shall enunciate certain general principles that I believe should be followed in respect to the technical side of the development of all Australian industries. The problem can, I suggest, be considered in three parts-technical education production, and research. I shall confine my remarks mostly to the research aspect, for it is with this that I am most familiar.For the efficient development of any industry in Australia, it is essential firstly that We should learn what is going on abroad, and secondly that we should simultaneously conduct independent research. In the latter sphere the Governmeht'departments and the private companies' or groups of companies should have complementary functions, the former concentrating on problems common to a number of companies or industries, and the latter on their oWn individual problems. It is essential to the continued existence of Australian industry that both company and govern...

Jan 1, 1944

AustraliaÆs strong position as an aluminium producer and potential magnesium producer combined with rapid market growth in the automotive industry, proximity to Asia and other natural advantages points to considerable opportunity for downstream processing and manufacture with light metals in this country. Development of a vertically integrated light metals industry in Australia needs to be pursued with vigour, as does the continued development of global strategic alliances through the value adding chain.

Jan 1, 2000

By R G. Richards

Although most New Zealand coals are low in ash, there are situations where high ash coals could be won. Not all high ash coals can be upgraded by physical means, since the ash is either inherent in the coal or bound in such a way to make its physical removal either impractical or uneconomic. Nevertheless, the authors believe, the situations where high amounts of ash can be economically removed by physical means to make a saleable product are considerable.

Jan 1, 1979

By S Jahanshahi, D R. Swinbourne

A knowledge of the value of the activity coefficient of cobalt oxide in slag as a function of composition and temperature is necessary if effective strategies are to be devised to maximise the recovery of cobalt in nonferrous smelting processes. This work reviews previous studies and shows that comparison and evaluation of the results is hampered by variations in the choice of standard states for the species. Published results have been recalculated to a common set of standard states with a preferred value for the Gibbs free energy of formation of cobalt oxide. It has been shown that the value of the activity coefficient of cobalt oxide referred to the solid standard state in iron silicate slags is approximately two, at temperatures from 1523 to 1623¦K. It is suggested that some contradictory results are most likely due to errors in the measured partial pressure of oxygen.

Jan 1, 1998

The treatment plant at Martha Mine was upgraded from a nominal throughput of 110tph (O.93mtpa) to 150tph (1.25mtpa) late 1999. Post-upgrade performance did not meet expectations when treating either the competent primary ore or the clay-rich oxide ore.   ò Plant throughput is constrained by milling capacity when treating the competent primary ore. This is not an issue at present as current plant feed is oxide ore from the top of the open-pit, but will become so in future years as the pit deepens. To counter this future threat, ball mill power has been restored to 1100kW through modifications to the drive train. The addition of a crushing circuit may also be necessary.   ò Plant throughput was originally constrained by thickener and leach/adsorption tank issues when treating the oxide are. Changes to plant equipment and operations has seen the removal of these constraints and throughput on this material is no longer a problem.   The most significant issue facing plant staff at present is the high silver grade and its impact on gold recovery. These high grades impact upon recovery through losses caused by insufficient leach and adsorption capacity. To counter this, the geology, mining, and milling teams are working together to blend the high grade silver zones with lower grade ores - this is seen to be the quickest and most cost effective way to deal with the issue. The plant design has also been evaluated with a view to modifying it to cope with the higher silver grades. The viability of these modifications will depend on cost and time (that is, the length of time to implement any modifications versus the length of time to mine out the high silver zones).

Jan 1, 2001

Polyacrylamide flocculating agent has been used in the Leaching Division 'of the Risdon Works of the Electrolytic Zinc Company of Australasia Limited since October, 1960. The number of thickeners in the continuous thickening stage was thereby reduced from eight to three. There has been an increase of 25 per cent in throughput and a reduction of solids in thickener over-flow from 3-4 g/l. solids to 0·5 g Ir. solids. Reagent addition has been at the rate of 0·25 lb Separan NP10 per ton solids.Additionally there has been a gain of 3 per cent in current efficiency as the direct result of the addition of Separan NP10 to purified cadmium sulphate solution priOl; to electrolysis for cadmium metal. A smoother deposit has resulted and it has been possible to increase deposition time between strippings from 47 to 71 hr. However, there has been a slight increase in the lead content of the cadmium metal produced.The use of Separan NP10 to settle copper bearing residue in a batch process stage has resulted in a five-fold increase in settlement rate and a reduction in purification cycle time.INTRODUCTIONThe Electrolytic Zinc Company of Australasia Limited, Risdon, Tasmania, produces zinc by electrolysis of purified zinc sulphate solution, the raw material being zinc sulphide concentrate. In the Risdon process (Van Arsdale, 1953; J ohnstone, 1953; Ross, 1949) the compound zinc ferrite (ZnO.Fe203) is formed during the concentrate roasting stage. When the roasted material is leached in dilute sulphuric acid the zinc ferrite is not attacked, and it remains as part of the insoluble leach residue, of which it may form as much as two-thirds of the whole. The remainder is mainly unroasted zinc sulphide, unleached zinc oxide, lead sulphate, gypsum, silver compounds etc. The zinc in the residue may be 10 per cent of that in the original concentrate.Continuous thickeners are used to recover the valuable residue from the impure zinc sulphate solution and the...

Jan 1, 1963

By J Guo, K Williams, S Caldwell, W Chen

Mining is increasingly occurring near or below the water table. This has led to a higher rate of handling problems associated with increased moisture and increased adhesion, which lead to a higher rate of blockage events within the materials handling chain. Typically, these ores and minerals are known as ‘wet and sticky materials’.Currently there is very limited knowledge and/or methodologies for effective design of efficient materials handling systems when it comes to handling wet and sticky materials. However, there is one major parameter that significantly affects handleability of a wet and sticky ore; namely, its moisture content. Flow property testing has shown that when moisture is reduced, the adhesive properties of the ore are also significantly reduced, thereby increasing ore flowability.The research embodied in this paper investigates the moisture reduction rate through a loose packed bed of iron ore using dry, ambient temperature airflow. A comparison of the predictive capabilities of a proposed drying model to data obtained from on-site experiments using iron ore fines is made. Building on an assumption made by Hukill (1954), a second term has been proposed to account for rewetting effects in the drying process. From this research, identification of improved moisture reduction approaches is envisaged.CITATION:Caldwell, S, Williams, K, Guo, J and Chen, W, 2017 Aeration induced moisture reduction of iron ore, in Proceedings Iron Ore 2017, pp 455–460 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By Clements R. J, Davey J. M

Development of the process from the pilot stage to the current operation of the Capel, WA plant is briefly described.The design criteria for a larger sized plant are discussed together with factors that relate suitable feedstocks and coal types to the capital cost, capacity and product grade of future plants at locations other than Capel. The application of the process to the direct reduction of iron ores is briefly discussed including its commercial application at Rockwood, Tennessee.

Jan 1, 1980

The history of soft and hard rock underground mining is blemished with regional instabilities of mine workings. Whilst the potential consequences of regional instability events are recognised to be high, there is a false perception that the probability of them occurring is very low. In fact, Australia has averaged more than one event per year for the past 20 years. At least five fatalities and over $100 million of losses have been associated with the events. As such, they are a core risk to underground mining and have a significant effect on the quadruple bottom line of business û safety, environment, community acceptance and economics. This paper explores the important roles that risk management has in reducing the probability and consequences of regional instabilities. It concludes that education and continuing professional development are essential elements for effectively managing the risk.

Jan 1, 2003

By Madgwick J. C, Ralph B. J

A method for the determination of microgram quantities of uranium in leachates from low grade uranium ores is described. Solubilized manium is purified by transfer to an organic solvent by a selective solvent extractionprocedure using tributyl phosphate, iso-octane, and aluminium nitrate. The organic phase is mixed with scintillation fiuors in toluene and the radioactive decay determined in a liquid scintillation counter. The method is sensitive and reproducible in the range 3-30 µg uranium.

Jan 1, 1978

The epithermal Au-Ag deposits of the Hauraki Goldfield have formed in the convergent plate margin setting of the Coromandel Volcanic Zone (CVZ). The deposits form as siliceous lodes in the upper parts of geothermal systems associated with andesitic and rhyolitic volcanism. Two types of low sulphidation epithermal mineralisation are recognised in these volcanic terranes. Vein deposits within the rhyolitic terrane in the east and south of the CVZ (Whitianga Province) are typified by Chalcedonic Silica-Adularia-Illite type mineralisation. The veins are hosted by both rhyolite-dacite volcanic rocks and the underlying andesitic basement. The mineralisation formed by episodic violent decompressional boiling of deeply circulating meteoric water, with some magmatic fluid contribution; this boiling was associated with hydraulic fracturing and hydrothermal eruptions in geothermal systems where the piezometric surface of the deep geothermal reservoir lay near-surface. Such episodic boiling provides chalcedonic veining, banding and brecciation textures, adularia stability, bladed calcite, and extreme loss of H2S gas from the fluid to cause major gold deposition.   Crystalline Quartz-Illite-(Adularia-Kaolinite) type mineralisation is widespread in the andesitic terrane forming the northern and western portions of the CVZ (Kuaotunu Province). There is a spatial association with weak mineralisation of the high sulphidation (Vuggy Silica-Alunite-Kaolinite-Illite) epithermal type and porphyry eu-Au type. Crystalline Quartz mineralisation is probably formed by the mixing of shallow acidic groundwaters with the ascending deep geothermal fluid in geothermal systems beneath andesitic stratovolcanoes. The piezometric surface to the deep geothermal reservoir in these systems is likely to lie at considerable depth, with acidic gases rising from the geothermal reservoir condensing within the overlying vadose zone. The cooling effect, oxidation and pH decrease accompanying mixing apparently overcomes the dilution effect, and results in quartz deposition, illite (and locally kaolinite) alteration, and precipitation of gold. A high level of base-metal sulphide precipitation also enhances gold deposition. Violent boiling of the mixing fluids may occur at local structural dilation sites, producing high grade "bonanza" gold mineralisation.

Jan 1, 1991

By A B. Christie, F P. Bierlein

Lode gold deposits of the Western and Eastern provinces, South Island, New Zealand , formed as a part of the Cordilleran-style tectonism during Tasman/Tahua and Rangitata orogenesis along the Paleozoic-middle Mesozoic southern Gondwanan margin. These deposits, hosted by lower grade greenschist facies sedimentary rock sequences of the Buller, Takaka, Torlesse, and Caples terranes, universally show geological features that are consistent with the orogenic gold deposit model, and genetic features are generally suggestive of a metamorphic origin, with the possible exception of a magmatic fluid source for the mineralisation at Sams Creek. However, ore fluid chemistry in Mesozoic deposits of the Eastern province, particularly the low concentration of non-aqueous volatiles and the very dilute nature of the fluids, is uncharacteristic of most orogenic gold deposits; this must be explained by either a unique fluid source or fluid type, which we believe unlikely, or an unrecognised significance of relatively rare gas-rich fluid inclusions in the deposits. Absolute age data for gold deposits in both provinces remain equivocal, thus hindering definition of the exact temporal relationship between ore formation and terrane accretion, regional metamorphism, and magmatic arc emplacement. Mercury and antimony occurrences in subgreenschist grade parts of the Haast Schist may target the upper levels of unrecognised orogenic gold deposits. If low-grade, high-tonnage intrusion-related gold systems occur on the South Island, then they are most likely to be discovered in association with the small molybdenite-, scheelite-, or cassiterite-bearing quartz stockworks spatially related to the Karamea and Median batholiths.

Jan 1, 2005

The Archaeozoic Willyama Complex at Broken Hill has suffered several periods of deformation and metamorphism. New structural and petrological information together with that available from the literature gives a picture of the metamorphic evolution of the Barrier Ranges. Several epochs of metamorphism are recognized, and potassium-argon dating of minerals has been applied with limited success to the resolution of these epochs.INTRODUCTIONAdvancements in the mineral industry at Broken Hill over the past eighty years have been accompanied by a continual striving towards increased understanding of both the geological history of the Barrier Ranges and the environment of the Broken Hill ore deposits. However, although many detailed studies of selected localities and particular-aspects of Broken Hill geology have been carried out recently, the regional geology of the Barrier Ranges as a whole has received little attention from a petrological viewpoint since the pioneer investigations of Mawson (1912) and Browne (1922). There still remains a great need for regional surveys combining field studies of the habits, structures and outcrop relationships of the various rock types with laboratory investigations of their chemistry, mineralogy and microscopic ,fabrics. Recording observations arising from three brief visits to the Broken Hill area during 1959 and 1963 may stimulate further surveys.During one of these visits, the generosity of the Zinc Corporation Limited in providing field transport and geological guidance enabled the writer to collect material and study field relationships and appearance of the various rock types at numerous localities covering most of the Willyama outcrop. A complete study has not been conducted...

Jan 1, 1963