Search Documents

By Chris Larsen, Ian Orford, Mike Cooper

"An autogenous grinding circuit was commissioned at the Brunswick concentrator in October 1998. The autogenous grinding circuit replaced existing surface crushing plants, fine ore storage, rod and primary ball mills. The 8.54m diameter x 4.27m long (EGL) AN1 mill is driven by a bidirectional variable speed 6.3MW ABB wound rotor motor with Slip Energy Recovery (SER) drive. The AG mill was subsequently converted to SAG operation in May 1999 for a number of reasons. The mill is operated in closed circuit with horizontally inclined 660mm diameter cyclones to produce a circuit product P80 of 85 microns. Extensive test work and JKSimMet design modeling resulted in a production circuit operating closely within design expectations.The circuit is highly instrumented and controlled via a hybrid Programmable Logic Controller (PLC-5) and Fisher PROVOX Distributed Control System (DCS) that is in communication with the property information highway. An expert control system (Gensym G2) is used for control of the SAG mill load.Engineering and construction were completed in 28 months from the time of management approval for the project. The Brunswick AG/SAG mill circuit was commissioned on schedule at the $M 23.5 forecast budget."

Jan 1, 2001

By R. J. Balfour, T. L. Papucciyan

"INTRODUCTIONCapital Cost considerations are basic to feasibility in the achievement of success for Mineral Processing Projects as much as or more than in many other industries. Capital cost is an important factor ae it 1R the unit of measurement for process engineering economic decisions. As a result of ever increasing complexity, alternatives of process and remoteness of site, there is an ever increasing emphasis on accurate estimating and the attendant cost control systems in the international market of today for the Mineral Industry where initial plant costs are becoming a more important factor than operating costs. An undervaluation means trouble ahead. An over-cautious assessment may bring an unnecessary abandonment of a project. Consequently, the ultimate cost must be predicted early and accurately and must be controlled to this parameter during the design and construction phases. Cost Est!~ mating is one of a variety of project management tools used to assist in planning and achieving the optimum balance between Quality, Cost and Time, the eternal triangle of evaluation, namely obtaining a project of acceptable quality at minimum cost and on time. In order to attain these established objectives, proper planning, organizing, coordinating, monitoring, adjusting and controlling the design, procurement and construction elements of the project are essential.This project management approach based upon the principle of a Task Force under single management, comprising a complete service organization, requires a substantial number of qualified individuals specialized in their own field and capable of working together as a team to perform their various functions effectively. The Task Force is supported by their chiefs of discipline and performs in accordance with established procedures and standards under the leadership of a Project Manager.General Engineering Company Limited with the backing of the full resources of Surveyer, Nenniger & Chenevert and its total staff of approximately 1,0009 offers the complete project management service to the Mineral Processing Industry of North America and the rest of the world. As mine sites become more remote and difficult of access, the need for an experienced team of specialists who work under the Task Force principle, with well established standards and procedures becomes even more important. Our long history of successful pro1ecta in this field has been our training ground for the fulfillment of this need."

Jan 1, 1972

OVERVIEW OF PRESENTATION ? What is LMI ? Who uses LMI and how? ? Value of LMI to the Mining Industry ? Mining Industry Workforce Information Network (MIWIN) ? The Challenge: Forecasting the future in uncertain times ? Results: Hiring requirements in the next decade ? Results: Occupational information ? Next steps

May 1, 2009

By B. Jago

From the perspective of metallurgical processing, gold ores can be classified into freemilling and refractory ores. Their extractive metallurgy is largely driven by mineralogical factors such as gold particle size, association with other minerals, coatings and rimmings, presence of cyanicides, oxygen consumers and preg-robbers, presence of refractory gold minerals, and invisible gold in sulphide and sulpharsenide minerals. Gold process mineralogy helps address issues and problems related to gold ore processing. It is widely used as a predictive and trouble-shooting tool in gold ore processing, and provides useful information on process selection, flowsheet development, recovery improvement, and reagent consumption optimization. By combining classic mineralogical techniques, modern instrumental analysis, and diagnostic metallurgy, the mineralogist is able to balance the various types of gold occurrence in an ore.

Jan 1, 2006

By John Russell

"Faster, safer, grinding mill relining offers the obvious attractions of reduced mill relining times with the knock-on incentive to reduce all other maintenance down-time, opening the possibility for increased annual plant utilisation.Leading edge liner handler technologies by RME, focused toward even shorter relines for very large SAG and AG mills, have recently split into two quite distinct paths:•,?Single SAG/AG Mill Relining Machines (MRM’s) of very large capacity, such as Newcrest Cadia’s 40’ SAG MRM of 6000 kg capacity and P.T. Freeport’s 38’/34’ SAG MRM of 7250 kg capacity;•,?Twin-machine SAG/AG Mill Relining Systems of moderate to large capacity such as BHP Billiton’s Escondida Laguna Seca 38’ SAG MRM’s, each featuring 4500 kg capacity.RME, its customers noted above and their liner suppliers are providing leadership in this important annual utilisation advance.Once the 24 hour mill shell reline becomes reality, liners designed for maximum profit, not maximum life, albeit exchanged more frequently, become possible too.INTRODUCTIONAt most mineral grinding plants, mill relining activities dictate each maintenance shutdown’s critical path. When annualized, mill relining remains the largest, single influence in defining plant availability.Because of restricted access, both inside and outside the mill, increased application of manual labour has no effect on reducing relining downtime. The only answer for RME has been to develop and apply new relining technologies now known as RME’s Mill Relining System.RME’s primary focus for over twenty years has been the reduction of grinding mill relining times while simultaneously providing a marked improvement in relining safety. Our original (1990) target was to halve traditional (pre-RME) reline times and to eliminate accidents and injury by mechanizing all physical work."

Jan 1, 2008

By J. C. Escobedo, J. M. Almanza, A. Flores, Cortés. D. A.

Secondary aluminum dross, which has been exposed for several years to atmospheric conditions, was characterized using chemical analysis, X-ray diffraction, optical and scanning electronic microscopy, and energy-dispersive spectroscopy. Based on the characterization, a method to purify the solids is presented. This method starts with the washing of the dross in boiling water to eliminate the soluble compounds like Na and K, followed by the physical separation of the metallic aluminum by milling and screening. Finally, an acid lixiviation process is applied using three different acid solutions, HCl, HNO3, and H2SO4. The best results were obtained using HCl. The main insoluble components of the dross after lixiviation were Al, SiO2, and Al2O3. MgAl2O4, AlN, Si, and Na2Al22O3·2H20 species were also found. Based on the alumina content, the solid product could be suitable as a raw material in the manufacture of castable refractories or metal matrix composites.

Jan 1, 2005

By I. Dimitrov, S. R. McCutcheon

"Industrial-grade limestone is found in both the Lower Silurian La Vieille Formation and Upper Silurian LaPlante Formation of the Chaleurs Group in northern New Brunswick. Currently, between 150 000 and 200 000 tonnes of limestone are produced per year from the proximal facies of the LaPlante Formation at the Sormany quarry of Elmtree Resources Ltd., located west of Bathurst.The proximal facies of the LaPlante Formation was deposited on the margins of tectonically uplifted Ordovician terranes. This facies comprises stromatoporoidal-algal bindstone intercalated with wackestone, packstone, and floatstone in variable proportions. The distal facies comprises calcareous shale and minor limestone deposited deeper offshore.Folding and faulting related to Middle Devonian Acadian tectonism have caused an increase in the apparent thickness of the limestone sequences, especially adjacent to the regional Rocky Brook-Millstream fault. Structural and stratigraphic observations indicate that some of the limestone bodies in the area have been tectonically displaced from their site of deposition.A variety of prospecting techniques was used to locate new limestone resources, including geological mapping, airborne and ground electromagnetic surveys, and satellite remote sensing. Clastic rock units above and below the LaPlante Formation have distinctive properties that help to trace the intervening limestone along strike. Because of water-saturated glacial cover, thick vegetation, and the small size of targets, airborne geophysical methods did not prove effective in delineating limestone beds, but aeromagnetic surveys helped map the underlying clastic unit. The remote-sensing data and especially high-resolution digital elevation models helped in identification of karst topography related to limestone."

Jan 1, 2007

By C. Dirscherl, M. Combes

"Declining ore grade, leading to increased material transport and plant throughput requirements, is one of the major challenges in the current mining environment. This is accompanied by rising energy and labor costs, decreasing plant productivity and the requirement for highest plant availability. Siemens’ answer is the latest gearless drive technology for grinding and conveying. Gearless drive solutions are surpassing the mechanical limits of conventional drive systems serving to utilize the principle of economies of scale. By elimination of various components of the drive train the maintenance activities and spare parts inventories are reduced. The advantages are culminating in the incomparable availability of the Siemens’ gearless drive technology of 99.46 to 99.71% - as confirmed by real operational data from the Antapaccay mine in Peru. It was the first plant worldwide to use gearless drives for both applications.INTRODUCTION – THE GEARLESS PRINCIPLE The principle idea behind a gearless drive system is to reduce the number of components and diversity of parts. Especially those components that are at the edge of current manufacturing or power limits are eliminated. The used equipment provides the possibility to scale up and increase the power transmitted to the driven machine. This finally results in a possible increase of throughput respectively transported or processed material. In order to apply this principle of simplification we will take a look at the components of a conventional drive system consisting of: - Driven equipment (mill, conveyor, slurry pump) - Components altering the rated speed (gearboxes, girth gear / pinion) - The electric motor - Starting devices for the motor (VSD, CCV, LRS, clutch), which are necessary because a direct across-the-line start of high power motors with load would result in a significant drop in the line supply voltage - Alternatively a variable speed drive (VSD) or cycloconverter (CCV) to utilize the possibility of speed variation during operation - The electrical supply system (cables, switchgear, transformers, protection equipment)"

Jan 1, 2014

By D. Wolfe, K. Reid, T. Nunn

"The Aurora North mine has been operating for more than ten years, and is the source of over half of Syncrude’s bitumen production. In order to minimize front-end rejects, and to allow for high throughput, the ore top size at Aurora has been set at a nominal 125 mm. These relatively large lumps have a significant effect on both pump performance and pipeline pressure gradient. Current design methods underestimate the solids de-rating effect of lumpy slurries in pumps, and do not accurately describe the distribution or magnitude of the lump effect on pipeline pressure gradient. Data from the Aurora hydrotransport systems has been compiled, to quantify the effect of lumps on the pump head ratio and pipeline pressure gradient, and how this effect changes as lump ablation occurs along the length of the pipeline. A model has been built, using a logarithmic curve, which predicts the effect of 125 mm lumps on pipeline pressure gradient as a function of velocity and the distance from the start of a hydrotransport pipeline. This model is applicable only to Aurora hydrotransport operation, but similar models could be developed for other operations using the same methods. Using accurate pipeline pressure gradients and pump head ratios when designing future hydrotransport pipeline systems will help improve their reliability and operability."

Jan 1, 2014

By Rob Sloan, Simon Yu, Rob Robison, Mark Schmidt

"In 2000-2009, Highland Valley Copper (HVC) tested new generation 660 mm cyclones supplied by various manufacturers in an aim to replace existing first generation 762 mm cyclones without success. Due to plant infrastructure limitations, new generation larger (838 and 800 mm) cyclones were not feasible. In 2010, an approach of testing hybrid 800 mm diameter cyclones was initiated by HVC. The hybrid cyclone consists of an 800 mm cyclone upper head section and the use of existing 762 mm cyclone conical sections. Three hybrid 800 mm cyclones were engineered and fabricated, targeting a throughput of 850-950 mtph and were installed in the E line cyclone cluster. Since starting operation on September 20, 2011, three hybrid 800 mm cyclones have been running at combined throughput ranges of 750 to 1050 mtph. Based on plant Daily Met Reports, the test hybrid cyclones demonstrated a decrease in misplacement of coarse copper bearing material to the cyclone overflow and better cyclone efficiency when compared to the existing 762 mm cyclones at the same throughput. The hybrid 800 mm cyclones also demonstrated significantly higher capacity per unit when compared to the existing cyclones. Based on the improvement demonstrated in the full plant trials, HVC decided to install the new hybrid 800 mm cyclones in all five grinding lines starting in July, 2012. A more detailed discussion of the full plant trials and initial results of the first complete retrofit of E line will be presented. INTRODUCTIONHighland Valley Copper Partnership (HVC) is Canada’s largest base metals mine and one of the world’s largest producers of Cu-in-concentrate. The mine, located in the central interior of British Columbia, is owned (97.5% interest) and operated by Teck Resources Ltd. In 2011, HVC produced about 210 million lbs. of Cu and 8 million lbs. of Mo. HVC’s Mill Modernization Project (MOP), which was budgeted for $475 M, is currently under intensive construction and is scheduled for commissioning in Q1 2014. The following description was valid at the time of writing this paper.The operation has been expanded a number of times since the startup of the original Lornex mill in 1972. The plant started up with two 9.75 m (32 foot) diameter primary SAG mills. It was expanded in 1981 with the addition of a 10.36 m (34 foot) diameter SAG mill. In 1988, the Highmont concentrator grinding mills and flotation section were moved and attached to the Lornex mill site. This added two10.36 m (34 foot) diameter AG primary mills to the Highland mill. This brought the total number of primary mills to five referred to as Line A, B, C, D and E: three SAG mills (A, B and C) each with two ball mills in parallel and two AG mills (D and E) each with one ball mill. Each AG mill line is equipped with one short head pebble crusher. Ball mill circuits are classified using 8 clusters of ten Linatex 762 mm cyclones to reach a target P80 330 micron (equivalent 43% +100 mesh), before the cyclone overflow product advances to the bulk flotation circuit."

Jan 1, 2013

By J. A. Finch

"A method of sampling and presenting bubbles for imaging for use in full-size flotation cells is described. The device (bubble viewer) comprises a tube attached to a sealed glass viewing chamber. The assembly is first filled with frother-containing water (to prevent coalescence) and the tube immersed at the desired location below the froth. For a few minutes bubbles are collected in the viewer free from slurry and are readily imaged. To reduce bubble overlap and the problem of defining the plane of view, the viewing chamber has a sloped side. Bubbles rise, encounter this slope, spread into a single plane and slide up. This simple expedient virtually eliminates overlap and provides an unambiguous focus plane - the underside of the sloped glass. The bubble image is captured and processed to give size data. The bubble viewer has been employed at several concentrators on different types of flotation cells. Examples of the images are given. The impact of position in the cell and the effect of changing gas rate on bubble size are illustrated. This technique provides a sensitive measure of the effects of process variables on bubble size.INTRODUCTIONDespite the extensive use of flotation in the mineral processing industry, the methodology employed for cell design is largely based on empirical rules rather than on first principles. One of the main reasons for this state of affairs is that the local flow structures encountered in industrial-scale machines are very complex. These flow structures are difficult to simulate under the controlled conditions of the laboratory and the difficulty to solve the mathematical models that treat the randomness of such flows also mean theoretical treatment is limited. Understanding flotation cell hydrodynamics requires reliable data, which involves the implementation of measurement techniques capable of performing both at the laboratory- and the industrial-scale, In addition, it is desirable that such techniques are amenable to automation to reduce extensive manual intervention in the data collection process."

Jan 1, 2002

By Brigitte J. Dejou

The Red Dog sediment-hosted zinc-lead deposit is located in the Brooks Range thrust belt in northwest Alaska, approximately 1000 km northwest of Anchorage. The mine constitutes the primary deposit in a 400 square kilometre district, which hosts several other mineral occurrences. All the known mineralisation is hosted by the Mississippian Ikalukrok Member, deep basinal shale of the Kuna Formation, part of a Devonian to Cretaceous sedimentary sequence. The rocks underwent intense deformation during the Brookian Orogeny in Middle Cretaceous time. Several thrust faults juxtapose the stratigraphy. The Red Dog mine is composed of four deposits which together contain 105 Mt in resources and reserves for a total resource exceeding 18 Mt of Zn metal. The mine is an open pit with 25 foot high benches. The biggest challenge is not the Arctic conditions, but metal extraction, due to the fine grained nature of the mineralisation and the variability of the ore. The mine produces Zn and Pb-Ag concentrates that are shipped to smelters around the world from the Red Dog port facilities during the short summer period. Ore mineralogy is generally simple and consists of sphalerite, pyrite, galena and marcasite. The deposits are generally overlain by decametre thick exhalative barite horizons and exhibit strong silicification, which locally obliterates the original textures. Although described as a world class Sedex-type deposit, a large portion of the mineralisation exhibits sub-surface replacement textures. Moreover, unlike most other Sedex deposits, the reconstruction of the basin is made difficult by the structural complexity of the district. To assist exploration in the district, several assumptions are made regarding the deposit settings relative to metal source, growth faults or crustal extension.

May 1, 2006

By A. Tylczak, C. Norman, C. Shook, S. Loif

"There are a lot of good reasons to manage energy use at mining operations. Optimizing process energy use reduces operating costs. Tracking energy use can help identify unplanned process changes or malfunctioning equipment early, which allows problems to be corrected promptly.Sacré-Davey Engineering in Vancouver has performed over 50 Energy Management studies for various industries including: mining, pulp and paper, oil and gas, etc. Energy Management programs can be used to identify energy reduction opportunities, assess project feasibility, complete equipment selection trade-offs, as well as to monitor and manage energy costs. Benefits of energy management programs are reduced energy costs, reduced maintenance, and increased plant automation. Additionally, energy management can provide access to utility incentive funding and quantify savings which can greatly improve the return on investment of potential projects.Energy management studies are funded by many Utility programs across Canada. There are various programs available for existing plants energy audits, project feasibility studies, new plant design reviews and energy monitoring and targeting, etc. There are capital incentives available which can significantly reduce payback period.This paper discusses how energy management can be used to support mill/mine operations groups, maintenance programs, as well as expansion or green field projects. This paper will also provide an overview of Canadian Utility companies programs and how they can assist mining companies.IntroductionThere are a lot of good reasons to manage energy use at mining operations. Optimizing process energy use reduces operating costs. Tracking energy use can help identify unplanned process changes and identify malfunctioning equipment early, which allows problems to be corrected promptly."

Jan 1, 2015

By P. A. Mingione

"AEROPHINE@ 3418A is a unique sulfide mineral promoter produced by Cyanamid, based on phosphine (PH3) chemistry. It has proven effective as a collector for the sulfide minerals of copper and particularly lead (galena), as well as for secondary gold and silver values. AEROPHINE 3418A has widest application as a Cu and/or Pb collector for complex ores of Cu-Zn and Pb-Zn, which frequently have significant quantities of associated precious metal values. Advantages shown in the use of AEROPHINE 3418A are improved selectivities against Zn- and Fe-sulfides, increased precious metals recoveries, reduced total collector consumptions for Cu and/or Pb flotation, and increased flotation kinetics leading to higher recoveries of these values. Operating plant, pilot plant and laboratory test data from treating different ores are presented, demonstrating the advantages in use and preferred application of AEROPHINE 3418A.INTRODUCTIONCyanamid operates the only phosphine and phosphine derivatives plant in North America, located in Niagara Falls, Ontario. Specialty chemicals manufactured at this facility are used in many diverse applications, including solvent extraction reagents and textile flame retardants. A unique phosphine-based sulfide mineral promoter, AEROPHINE 3418A, is also produced. The origins of AEROPHINE 3418A promoter date back to the 1960's, when it was established that sulfide mineral collectors based on phosphine chemistry demonstrated efficacy. This new collector chemistry was found to provide flotation performance differing significantly from those of more traditional thiol collector chemistries such as xanthates, dithiophosphates, mercaptobenzothiazoles, thionocarbamates and those with xanthogen groups. Some of the advantages ultimately demonstrated by AEROPHINE 3418A promoter compared to these traditional collectors include:"

Jan 1, 1990

By Son Hye Jin

Abstract ? KHNP is participating in the construction of Nuclear Power Plant both in Korea and UAE. ? We want to improve our construction project management process. ? So we are now developing the process model on nuclear power plant construction management. ? For the effective adoption of this process, we are planning to develop IT system. ? For the first step, we were established the Information Strategy Plan

Aug 1, 2013

By R. Grant, C. Bazin

"Brunswick Mining has investigated grinding media optimization for the purpose of improving the flotation feed and regrind product size distributions to enhance metal recoveries. This paper presents the findings of on-going testing of various sizes and shapes of grinding media. Plant observations combined with estimated breakage rates demonstrate the importance of appropriate selection of media sizes on the milling operation.IntroductionBrunswick Mining and Smelting is located near Bathurst, New Brunswick, and operates one of the world's largest lead and zinc mines. The ore mineralogy and processing flowsheet have been described elsewhere (Petruk and Schnarr, 1981; Shannon et 01., 1993). Despite the 25 years' milling experience, there has been considerable disagreement as to the required grind size (Grant et 01., 1991). Since 1964, fineness of the flotation feed ranged from 60% to 80% passing 400 mesh (37 um) and averaged slightly above 71% in 1992. Results from mineralogical analysis (Petruk and Schnarr, 1981), laboratory and pilot plant experiments, as well as plant sampling (Grant et al., 1991; Hendriks and Ounpuu, 1985; Shannon et al., 1993) indicate that improved metal recoveries can be achieved by an increase in the fineness of grind, and more specifically by maximizing the amount of material in the 15 urn to 25 um range.This paper shows the results obtained so far from the evaluation of the effect of grinding media size and shape on grinding mill efficiency. The problem of finding optimum grinding media size, shape and composition has been recogrtized since the early 19405. The main criterion for the selection of media size is the size of the material to be ground (Bond, 1958). Although several relationships have been proposed to assist in the selection of grinding media size, none of them are entirely satisfactory (Wills, 1988). Other approaches using the breakage rates and process simulators were developed to help in the selection of grinding media size (Austin et al., 1976; Lo and Herbst, 1986; Concha et 01., 1992; Samskog et al., 1990; Martinovic et al., 1990). Although considerable effort was put into the analysis of grinding media size, very little information is available on the effect of grinding media shape (Norman and Decker, 1985, p. 3C-4). Norris (1952), Kelsall et al. (1973) and Herbst and Lo (1989) have shown that balls are more efficient than other shapes of grinding media including truncated cones and cubes."

Jan 1, 1994

By P. C. Holloway, A. Tshilombo, T. Xue, M. J. Collins, R. Lopetinsky, I. Mihaylov, I. M. Masters

The Voisey’s Bay deposit contains a trace amount of cadmium, which reports to solution during pressure leaching of the nickel concentrate at Vale’s Long Harbour Hydrometallurgy Plant, and must be removed to produce high quality nickel cathode. In 2006, Vale approached Sherritt Technologies to collaborate on the development of a process for removing cadmium to low levels (<1 mg/L) in the nickel raffinate. Following successful bench scale and pilot plant testing at Sherritt’s laboratories, the cadmium removal process was then moved through engineering and construction, culminating in the successful commissioning and startup of a cadmium removal circuit at the Long Harbour Hydrometallurgy Plant in 2017. This paper presents the results of this collaboration and the challenges that were encountered through each stage of development, as well as current results from operation of the commercial cadmium removal circuit. INTRODUCTION Vale’s Long Harbour Processing Plant, with a nameplate capacity of 50,000 t/y nickel, began operation in 2014. In addition to electrolytic nickel rounds, the plant also produces electrolytic cobalt rounds and copper cathode. The Long Harbour Processing Plant uses a unique hydrometallurgical process developed by Vale Base Metals Technology Centre, as shown in Figure 1, to treat a nickel sulphide concentrate produced at the Voisey’s Bay mine and mill located in northern Labrador (VBN concentrate) (Stevens et al., 2009).

Jan 1, 2019

By Terry A. Kirk

"This paper describes Derrick High Frequency Vibrating Screens and their process performance in grinding circuit applications. The benefits of screen sizing in closed circuit grinding are illustrated by case histories from a wide spectrum of mineral industries.INTRODUCTIONHigh capacity, reliable wet screening equipment is increasingly in demand by the mining and allied industries for separations finer than 1/.7 5mm (I/ mesh). The continuing search for improved energy efficiency and reduced steel consumption in comminution has Jed to greater scrutiny of every aspect of circuit design and operation, including the classifier efficiency (selectivity) function.Derrick Manufacturing Corporation has been developing high frequency screening machines designed specifically for grinding circuit applications since 1973. Successful installations are currently operating in iron ore, copper, coal, uranium, phosphate and other extractive industries."

Jan 1, 1984

By Jim Sadowski, Steve Stewart, Bob McMurdy, Martin Nevens

"Mohawk Garnet has been operating a small pilot plant near Sudbury, Ontario for several years attempting to produce commercially viable garnet. The challenges of operating a pilot scale mining, processing, and product handling operation as a full time plant have led Mohawk Garnet to seek a better way. In co-operation with Mohawk Garnet, Outotec (USA) Inc. has taken on the technical and design challenges of increasing garnet product from twenty tonnes per day to two hundred tonnes per day.Outotec performed a comprehensive test and flowsheet development program applying Outotec’s density separators, spirals, flotation, and other technologies to design a successful process for the separation and recovery of the valuable garnet for Mohawk.This paper explores the test program, the process flowsheet development work, plant design and preliminary engineering of a new garnet processing. The various technical challenges, process technologies involved, and design concepts will be discussed.INTRODUCTIONMohawk garnet has been operating a small-scale garnet mine and process plant in Wahnapitae, Ontario near Sudbury.The current operation was intended to be a pilot plant and so only produces 20-25 tonnes of garnet concentrate per day. The garnet is bagged and sold for use as abrasive. The process is inefficient with low yields, poor material handling and very high cost per tonne. Mohawk garnet approached Outotec to help them improve their garnet process and transform themselves into a larger scale and more efficient operation."

Jan 1, 2010

By D. Getzlaf

"Oilfield cementing has been utilized in the industry since the turn of the century. Originally, wells were shallow and criteria for well integrity were somewhat limited. Since that time, wells have stretched the envelope in depth, temperature, and pressure. Environmental regulations have also become more stringent, thus, the importance of hydraulic isolation between permeable zones, and between these zones and surface has become more and more important.Initially, oilfield cements were comprised predominantly of construction cement and very limited additives. As time progressed, additives were incorporated to control pumping time or placement time and little effort was placed on optimizing actual components within the cement chemistry. This paper presents issues and concerns created by adding just one new component to the fundamental chemistry of an oilfield cement."

Jan 1, 2004