Search Documents

TWO recent developments in open hearth steelmaking have had a substantial impact on metallurgical practices and operating procedures. These are: (1) the use of oxygen roof lances for accelerating the refining reactions, and (2) the use of a spring-arch, basic roof for prolonging the life of the furnace. Although these practices can be used separately, they are generally used to complement each other in an effort to obtain minimum heat time consistent with an acceptable rate of wear of the refractory roof, walls and port ends. DECARBONIZATION BY OXYGEN INJECTION The use of oxygen to speed carbon elimination was perceived by Sir Henry Bessmer but its practical use in steelmaking could not be realized until processes were developed for the manufacture of low cost, tonnage oxygen. However, as early as 1922 Bigge1 obtained a patent covering the use of gaseous oxygen to speed decarbonization of a molten steel bath. At that time, oxygen was available only in bottles and at a cost of $240 per net ton. At the end of World War II the price of oxygen had dropped to $80 per net ton, and as a result, metallurgical oxygen (99.5 per cent began to come into widespread experimental use for decarbonization in open hearth and electric furnace shops.2-8 Even this price prevented oxygen's routine use for other than decarbonizing the bath in shops producing substantial quantities of steels containing less than 0.40 per cent carbon. Today, tonnage metallurgical oxygen can be manufactured for less than $15 per net ton, and commercial purity oxygen (95 per cent is reported to cost less than $5 per ton. Thus, it is not at all surprising to find many open hearth shops effectively using large quantities of oxygen to accelerate decarbonization. Equipment for Oxygen Injection. The oxygen may be injected by a lance pipe inserted through the wicket hole and pushed several inches into the steel bath, or by a water-cooled jet inserted through the back- wall, endwall, or roof, and immersed in the slag or set just a few inches above the slag. Oxygen at approximately 100 psi is piped directly to control stations adjacent to each furnace. The installations should include adequate safety devices such as fire checks and emergency valves,

Jan 1, 1964

By Lauren A. Wright, A. E. J. Engel

Under the designations "industrial talc" and "soapstone" are included earth materials of widely different chemical and mineral compositions. Talc, the mineral, is a hydrous magnesium silicate, with a suggested theoretical formula H2Mg3(SiO3)4 or H2O.3MgO.4SiO2, which postulates 63.5 pct SiO2, 31.7 pct MgO, and 4.8 pct H20.18 Single grains or leaves of talc, however, seem to have variations in water content that range from 3.5 pct to more than 7 pct, as well as slight differences in the proportions of MgO and Si02.20 Most of the industrial talcs produced in the United States do not approach the composition given above (see Table 1), but are essen- [ ]

Jan 1, 1960

Nature: Man is but one of the creatures which in- habit the earth, a dust speck in the universe. Thinking man has been concerned with his place and purpose in the universe since the earliest Egyptian and Chinese philosophers. Ancient creeds, as well as modern religions and philosophies of life, were concerned with the same problem. While such considerations and concepts have been valuable, theoretical philosophizing and dogmatic concepts are inadequate for a satisfactory solution of world problems of today. The concepts of man and life and their ultimate purpose should be sought in the relations of intelligent man to man and their relation- ship to the physical world. The quintessence of nature's accomplishment-man- is also the greatest disturber of nature and the greatest enemy of his own kind. While his spirit and mind defy and overcome natural limitations, his physical self is controlled by the same basic biochemical laws that govern any other form of living matter. This paradoxical duality of human voluntary and involuntary relations to nature is the source of the perpetual conflict between mind and matter. Therefore, the higher the spiritual evolution and perfection of the individual's mind, the greater and deeper the conflicting elements in their expression; and conversely, the simpler the mind or the mental and spiritual heritage, the less is the individual concerned with the conflicting elements.

Jan 1, 1950

By Smith Bracewell

First evidence of bauxite in Jamaica resulted from an analysis of a soil sample collected at Bull Savannah in 1938 during a systematic local investigation of the island's soil types. Results of subsequent work indicated the possibility of the occurrence of deposits of commercial grade and dimensions, and in 1942, with a view to emergency development of the deposits as a war measure, the Jamaican Government declared all bauxite in the colony to be Crown property.

Jan 10, 1958

By C. A. Stickels

A heat of electrolytic iron, to whzch alunzinutn and nitrogen had been added, was hot-rolled, cold-rolled 90 pct, and recrystallized at temperatures from 500" to 700°C. Primary recrystallization textures appear to arise from competitive growth of two types of nuclei: 1) those having orientations belonging to the "usual" primary recrystallization texture found in riming steel, and 2) those with the {111} (110) ovientation. Development of a (111}(1 10) component in the primary recrystallization texture occurs only over a certain interval of isothermal recrystallizatzon temperatures when the material is supersaturated with respect to the precipitation of AlN. Lowering the degree of supersaturation depresses the temperature interval in which a (111)(110) component occurs. An elongated, 'pancake-shaped" recrystallized pain structure and a marked delay in the start of recrystallization were found in all specimens which were supersaturated with respect to A1N precipitation after cold work, regardless of their recrystallization texture. ONE of the consequences of killing low-carbon steel with aluminum is a significant change in recrystallization behavior. About 15 years ago, Solter and eatttiel showed that this behavior was largely controlled by aluminum and nitrogen in the steel. If complete precipitation of A1N was prevented before cold rolling, an increased "recrystallization temperature" was observed in subsequent. annealing, and the recrystal-lized grains were not equiaxed. Leslie et a1.2 studied this phenomenon in some detail and clearly demonstrated the relationship between A1N precipitation, recrystallization kinetics, and the development of "pancake-shaped" grains. It has also been known for some time that aluminum-killed steels, processed to produce elongated "pancake" grains, develop a (11 I}( 110) primary recrystallization texture. This texture has not been found in iron or low-carbon rimming steel as a primary texture4j5 but has been observed following grain growth in electrolytic iron.5 The present work was undertaken to study in more detail the effect of A1N supersaturation on recrystallization textures in iron. LITERATURE REVIEW The deformation texture in heavily rolled iron has been studied in detail by Bennewitz.~ The texture consists primarily of a partial fiber texture about a (110) axis in the rolling direction, designated here as fiber texture A. It includes the range of orienta- tions (111)[110] - (001)[ 110] - (11l)[110]. A weak secondary texture also is present.6 This is a duplex partial fiber texture about two (110) fiber axes located 60 deg from the rolling direction and 30 deg from the sheet normal. The range of this texture, designated here as fiber texture B, about the [101} fiber axis is (112)[110] - near (545)[252] - (211:1[011] *The range given here follows Bennewit~.~ A few pole figures from re-crystallized material indicate a broader range than this.' However, the components which are strongest in the recrystallization texture are in this range.'________________________________________________________ Primary recrystallization textures in unkilled steels can be accounted for by growth of members of fiber texture B present in the deformed metal.5 However, while members of fiber texture B dominate the primary texture, other orientations survive primary recrystallization as well. In particular, some {111}(110) members of fiber texture A must also grow during primary recrystallization, because a well-defined {1ll)( 110) texture develops during subsequent grain growth at 700°C.5 The unusual recrystallization behavior of deformed supersaturated solid solutions has been attributed to: 1) retention of the solute in solution,' 2) formation of coherent, preprecipitation solute clusters prior to and during re~r~stallization,~ and 3) formation of a precipitate prior to and concurrent with recrystallization.'~-'~ When aluminum is supersaturated with iron, the difference in grain boundary mobility between general high-angle boundaries and certain special coincidence site boundaries is apparently eliminated.' In aluminum-killed steels, precipitation of A1N can take place at ordinary subcritical recrystallization temperatures. The rate of precipitation increases with increasing aluminum or nitrogen contents.2'13 There is some doubt, however, as to whether true precipitates form during the time at temperature needed to complete recrystallization. Leslie ef a1.2 found that precipitation in one steel was complete after about 100 min at 700GC, or after about 1000 min at 650GC, as measured by chemical analysis for AlN. Aoki et a1.,13 using internal friction for dissolved nitrogen, showed that a large fraction of the dissolved nitrogen was removed from solution within a few minutes annealing time at temperatures from 400" to 800°C. However , the rate of formation of AlN, as detected bv chemical analvsis. was much slower than the apparent rate of nitrogen removal. Hasebe,'~~ using carbon extraction replicas, has identified A1N precipitates by electron diffraction in a 0.2 C steel, solution-treated at 1300°C and annealed 2 hr at 700°C. Borchers and kim,I6 also using a replication technique, observed precipitates after annealing treatments as short as 2 min at 640°C. However, Leslie et a1.' state that no A1N precipitate can be seen while recrystallization is being inhibited in aluminum-killed steel.

Jan 1, 1967

By G. W. Thompson

G. W. THOMPSON,* Brooklyn, N. Y.-This subject has two aspects, neither of-which can be ignored: these are the economic aspect and the technical aspect. Under ordinary conditions, economic law will take care of the conservation of tin. Under present conditions it seems desirable that economic law should still be permitted to operate as far as is practicable. It is true that this law operates rather slowly, and that under war conditions it cannot be depended upon to give our Government the supply it immediately needs. There should, therefore, be a designation of the essential industries by the Government, and tin should be supplied for those needs, letting the non-essential industries take what is left. At the same time, information ought to be forthcoming as to how tin can be conserved; with tin selling at 80 c. per pound, more or less, it is to the interest of every consumer to get the best information he can as to how he can save tin. Economic law would properly punish those who do not study their own interests in this way. I deprecate, therefore, any centralized socialistic effort toward avoiding penalties through failure to observe and obey economic law. In saying this, however, I am not unmindful that it is desirable for our Government to take such control of the tin situation as may be necessary to the prosecution of the war, practically regardless of the effect of such action upon individual industry, which should studiously seek to adjust itself to the new condition. The Government should promulgate such technical information as it can collect, showing how tin can be conserved, and should urge upon every consumer the exercise of his common sense in self-protection. There is very little danger of any one attempting to hoard or corner tin, in the present state of the market. Most consumers will be glad to live from hand to mouth, covering their sales by purchases, or vice versa. As to the technical aspects: Tin and tin alloys are used to give certain practical and also certain artistic results. The practical factors are those involved in proper adhesion, continuity of surface, protection, the right degree of hardness, proper working qualities, etc. The artistic results are those that appeal purely to the eye or to our cultivated sense of what is desirable. There is no doubt that a great deal of tin could be saved if there were not a demand for certain pleasing effects. How can this saving be brought about? The users of tin hearing alloys are not the only ones involved in this question. The manufacturers of solder and babbitt have for a long time sought to give certain appearances to their fabricated bars and ingots in order to make them more salable. The user of a solder is very apt to judge of its working qualities by the appearance of the bar; the same thing is true with regard to babbitts. Under ordinary conditions, manufacturers are justified in trying to

Jan 12, 1918

By M. B. Bever, A. B. Michael

The solidification of aluminum-rich aluminum-copper alloys was investigated for different solidification rates. The measured amounts of nonequilibrium eutectic were compared with the amounts calculated on the assumption of no diffusion in the solid. The morphology of the eutectic was studied and dendritic spacings were measured. Compositions of the cored primary solid solutions were determined by quantitative autoradiography after activation of the solute copper by neutron irradiation. CONSIDERABLE progress has been made in recent years toward an understanding of the solidification of metals. This is especially true for the factors involved in nucleation, the controlled growth of metal crystals from melts, and various aspects of the freezing of ingots and castings. Many features of the solidification process, however, are not understood adequately and much further work is required. In the research reported here the solidification of a series of aluminum-rich aluminum-copper alloys was investigated. Different degrees of deviation from the idealized case of equilibrium solidification were attained by varying the rate of solidification. Thermal analysis and microscopic examination were supplemented by lineal analysis and autoradiography. The latter required the use of radioactive tracers and was adapted to the quantitative determination on a microscale of concentrations of copper dissolved in aluminum. The tracers were produced in situ by activating the copper with neutrons. These techniques permitted a correlated interpretation of the temperature-time history, the amounts of nonequilibrium eutectic and the general morphology of the alloys, and yielded quantitative data on microsegregation. Nonequilibrium Solidification In the general case of the solidification of a solid solution in accordance with the phase diagram, the composition of the coexisting liquid and solid must change continuously. This change requires diffusion, which at best remains incomplete in the solid during solidification. The resulting inhomogeneity of the solid solution crystals is well-known as coring, dendritic segregation, or microsegregation. The generally accepted analysis of coring assumes that, 1—no diffusion occurs in the solid, 2—diffusion is complete in the liquid, and 3—the composition of the solid formed on cooling through any infinitesimal temperature interval is given by the solidus of the phase diagram. On this basis, In this equation m designates mass, x designates the concentration of solute and the subscripts L and S refer to the liquid and solid phases, respectively; the subscript o indicates the initial state, in which the liquid is identical with the entire system. Eq. 1 or its equivalent has been derived repeatedly'-7 and an analogous equation, known as Rayleigh's equation, has been used for distillation. The assumptions on which Eq. 1 is based do not include an infinitely fast cooling rate as sometimes stated. In fact, Olsen and Hultgren %ave shown by experiment that very high solidification rates suppress coring, presumably by preventing diffusion in the liquid and by the effect undercooling has on the composition of the nucleus. Coring thus occurs at rates of cooling which are too fast for a close approach to equilibrium in the solid and too slow to suppress diffusion in the liquid and to cause marked undercooling. If the liquidus and solidus approximate straight lines, Eq. 1 simplifies to The fraction of liquid present at any temperature during nonequilibrium solidification can be calculated from Eqs. 1 or 2. By the lever relation it is

Jan 1, 1955

By R. F. Mehl, R. F. Bunshah

A fast amplifier technique has been developed for the measurement of the rate of propagation of martensite in an Fe-29.5 pct Ni alloy. The time of formation of one plate of martensite is 3x10 sec and the rate of propagation is 3300 ft per sec approximately. IT has been known for some time that the plate-like structural unit of martensite forms from austenite with great rapidity. Wiester1 and Hane-mann, Hofmann, and Wiester took motion-pictures of the transformation as it occurs in a 1.65 pct C steel; they demonstrated that a single plate formed fully in the time interval between successive frames, viz., 1/20 sec, thus setting an upper limit. Forster and Scheil,3 using an Fe-Ni alloy with 29 pct Ni, recorded the sonic characteristics of the process electrically, upon an oscillograph, setting the upper time limit at 0.002 sec. Forster and Scheil,~ measuring the change in electrical resistance in the same alloy upon a cardiograph, set a limit of 0.02 sec. Forster and Scheil5 later, employing the same alloy, improved their technique, reporting an upper limit of 7.10 sec. In studying signals of such short duration, it is an important question whether the frequency response of the electrical system used is high enough compared to frequency of the pulse measured, or, put differently, whether the system is able to reproduce without distortion the signal arising, in this case, from the formation of a single martensite plate. Forster and Scheil (referring only to their last paper) obtained signals of a frequency of 30 kilocycles (hereinafter kc); this was about the frequency response of the equipment used; thus, if the signal had a frequency higher than 30 kc, it would still appear as a signal of frequency 30 kc. All of these results thus provided upper limits only. Recent developments in electronics have made available equipment with very high frequency response, very high sweep-speeds, high gain, etc. The electrical characteristics of such equipment, used in the present study, are given in Table I. Such equipment offers obvious attraction in the study of the rate of propagation of a martensite structural unit—and perhaps of other structural alterations proceeding at a very high rate. This paper reports an attempt to develop a technique employing such equipment to measure the time of propagation of a martensite structural unit and the variation of this with temperature, with the mode of formation—athermal and isothermal—in both polycrystalline and single-crystal samples; and from such measurements to obtain the rate of propagation. As will be seen, the results obtained are useful theoretically. Materials All data presented here are for an Fe-Ni alloy of the following analysis: 29.5 pct Ni, 0.027 pct C, 0.135 pct Mn, 0.094 pct Si, balance Fe. There were several reasons for choosing this alloy: 1—it is substantially the one used by previous investigators; 2—it exhibits both the athermala and the isothermal' mode of formation of martensite, both studied in detail by Machlin and Cohen; 3—the subzero temperatures of transformation in this alloy are experimentally very convenient; 4—it exhibits the "burst phenomenon";" 5—the change in electrical resistance upon the formation of martensite, a decrease, is great, approximately 50 pct.' The polycrystalline specimens were in the form of wires of 0.025 in. diameter; the single crystals were 1x1/4x1/4 in. Experimental Methods Electrical Apparatus: Fig. 1 is a schematic drawing of the electrical circuit used. The principle used in these measurements is the same as that used by Forster and Scheil." A small direct current, about 1 to 2 amp, is passed through the sample. When a martensite plate forms, the resistance of the sample changes and a high frequency signal is generated. This signal is picked up by the probes attached to the sample, fed into the bank of amplifiers and thence to the vertical deflection plates of a cathode-ray oscilloscope. The signal itself triggers the oscilloscope trace which flashes across the tube face and is photographed by means of a 35 mm movie camera at the end of a light-tight hood. The camera has no shutter. As soon as the signal flashes

Jan 1, 1954

By Harold S. Davis

SURROUNDING the nuclear core of an atomic energy plant there are usually one or more thick walls of concrete, as required to protect instruments and personnel from the harmful effects of nuclear radiations. Sometimes these massive walls are of ordinary concrete weighing about 150 pcf. To reduce wall thicknesses, concrete weighing 200 to 350 pcf may be used. Such high densities are obtained by using natural aggregate processed from heavy ore, or by using steel slugs or iron shot in concrete. Mix data for a number of high-density concretes are summarized in Table I.1 High density at low cost is of prime importance in shields designed to absorb gamma rays. On the other hand, biological shields located near the reactor core must attenuate neutrons as well as gamma rays. In general, a biological shield should contain: 1) heavy elements to slow down high energy neutrons and to absorb gamma rays, 2) either light elements or hydrogenous materials to moderate neutrons of intermediate energy, and 3) materials to absorb neutrons once they have been slowed down to thermal energies. Some shield materials, iron and water for example, are effective in one or more of the above ways. On the other hand, some otherwise excellent shield materials have certain undesirable radiation properties that limit the ways or number of places they can be used. For example, when iron absorbs neutrons it emits secondary gamma rays of high energy. On the other hand, boron absorbs neutrons avidly without producing high energy gamma rays. In spite of its high cost, boron is sometimes used in concrete to minimize production of secondary gamma rays. In some shielding applications it is necessary to avoid materials that become radioactive when subjected to neutron bombardment, continuing to give off high energy gamma rays for long periods after being removed from a neutron field.

Jan 5, 1957

By Earle E. Schumacher

THE elements silicon and germanium are not metals within the usual, intuitive association of the word, nor are they so within a stricter definition based on the electronic binding. Two properties associated with metals are plasticity and high electrical conductivity. These elements crystallize in the diamond cubic structure, an arrangement apparently not very favorable to slip, and are therefore brittle rather than ductile. Their electrical conductivity is not like that of metals the atoms are locked together by the covalent bond, which in pure and perfectly arranged material leaves but few electrons free to act as electrical carriers.† In further contrast to metals, their electrical conductivity can be greatly increased by raising the temperature. Yet silicon and germanium are not ideally nonmetallic. They are hard, solid, and possess a metallic luster. They exhibit that peculiar brand of electrical conductivity conveniently termed "semi- conduction," wherein, as shall be seen, lies much of their importance. Both, but silicon in particular, are important components in real metallic alloys and the methods of their reduction and preparation lie clearly in the province of the metallurgist. From their duality of physical and chemical properties, silicon and germanium, along with such elements as boron, diamond, gray tin, selenium, antimony, and arsenic, are considered semimetals or metalloids. Because of their importance to metallurgy and the im-

Jan 1, 1953

By C. C. Mattax, J. E. Bobek, M. O. Denekas

ABSTRACT investigations in recent years have shown that rock wettability can exert a profound influence on the displacement of oil by water from oil producing reservoirs. Core analyses frequently show oil recoveries from preferentially water-wet rock to be significantly greater than those from preferentially oil-wet rock. Thus, an accurate prediction of water-drive or waterflood oil recovery is dependent on the evaluation of reservoir rock wettability. Laboratory and field studies have been undertaken to examine and develop methods which may be used to measure rock wettahililiy, to investigate factors which may alter the wettability of reservoir rock, and to determine the wettability of specific reservoirs. It has been found that measurement of the rate and volume of spontaneous imbibition of the wet-ting phase by a rock is a reliable and reproducible test for semi-quantitarive determination of preferential rock wettability. Laboratory tests have shown that the wettability of reservoir rock may depend on both the crude oil composition and the rock type. Field and laboratory tests have indicated that coring flulids and core handling techniques can cause significant changes in the wettability of rock surfaces. However, a few fluids, brine in particular, appear not to affect core wettability and may be used when coring to determine reservoir wettability. Core handling and packing procedures have been developed which preserve core wettability during storage and laboratory testing. The wetfability characteristics of six reservoirs have been evaluated by wettabilify tests performed in the field on fresh cores cut with brine or special water-base muds. The tests indicated that all six reservoirs are water wet; however, the de-gree differed from one reservoir to another. INTRODUCTION Although surface properties of reservoir rock and interfacial characteristics of rock, crude oil, and water systems have been discussed for many years, the full significance of these properties to the production of oil is still in the process of evaluation. It is known, however, that one surface characteristic—preferential wettability of the reservoir rock—-is of paramount importance when the reservoir is being produced by water-flood or water-drive mechanisms. The importance of rock wettability has been pointed out by several authors'.',%* who have found that pref- erentially water-wet cores flood more efficiently than oil-wet cores; that is, more oil is recovered from water-wet cores in the early flooding stages than from oil-wet cores. Other authors'," indicate that waterflood oil recovery from cores of intermediate wettability may be greater than that from either strongly water-wet or strongly oil-wet cores. These recent investigations emphasize that the true wettability of a reservoir must be known before the performance of waterflood or water-drive reservoirs can be accurately evaluated. When reservoir wettability is to be determined by core analysis, precautions must be taken to maintain the original wettability which can be altered readily during coring5 nd testing.' In the coring operation the core may be partially or completely penetrated by the drilling fluid which, if it contains surface active materials, may drastically change the wettability of the core. Also, improper core handling during stcrage and testing may change its wettability because of evaporation of fluids or exposure to oxygen or surface active contaminants. One purpose of this paper is to discuss methods for obtaining, preserving, and testing cores without altering their original wettability. In addition, the results of wettability tests on fresh and preserved cores from six reservoirs are presented where special precautions were taken to obtain samples without altering their wettability during the coring operation.

By E. C. Barfield, D. G. McCarty

Two-dimensional analyses offer considerable promise in providing the basic information required to effect more precise control of petroleum reservoir performance. This paper describes a method for conducting some engineering analyses of this type using a high-qreed digital computer. The general approach is to (I) develop a representative numerical model of the reservoir and (2) employ a suitable numerical technique to solve the basic equation of flow and to develop the required engineering information for the particular case represented by the model. This technique has been used to calculate pattern performance in connection with several field projects involving water injection into oil reservoirs. This type of analysis involves sequentially (I) calculating the pres-' sure distribution in the reservoir and (2) tracking the progress of the interface between the displaced and displacing fluids in a step-wise manner to provide a depletion history of the operation. The particular analysis presented in this discussion is subject to the restriction that the mobility of the displaced and displacing fluids be equal and assumes that the fluids are incompressible and that gravity and capillary pressure do not affect the shape of the flood pattern. Complete two-dimensional .flexibility is maintained with regard to definition of reservoir rock and fluid characteristics, placement of physical restrains and boundary conditions, investigation of flow characteristics in the reservoir, and movement of the displaced and displacing fluid interface. The results of these studies indicate that the highspeed digital computer is well suited for conducting reservoir performance studies in two-space dimensions and that dependable numerical techniques are available for making such analyses. INTRODUCTION One of the problems facing petroleum engineers is that of providing more precise engineering control over reservoir operations at all stages during the depletion cycle. The most direct approach to this problem is to simulate the reservoir with some type of physical or mathematical model and use the information developed from the behavior of the prototype to predict the performance of the actual reservoir. This principle is, of course, not new, and a variety of simulation techniques have been developed to provide information on the behavior of oil and gas reservoirs. One straightforward refinement of present reservoir analysis techniques is the progress from one-dimensional reservoir models to those where the reservoir can be represented in two- and three-space dimensions. Multidimensional reservoir analyses are desired in order to show not only what is happening in the reservoir but in addition to show where in the reservoir the various phenomena of interest are occurring. Thus far, two-dimensional analyses have been confined predominantly to potentiometric and electrolytic model studies. However, when large numbers of wells are involved and where large-scale models are required, such problems become very tedious and instrumentation problems become acute." It is possible through use of numerical methods and general purpose digital computers to avoid many of the instrumentation difficulties and to relax some of the restrictions of previous techniques. The purpose of this paper is to discuss some recent experiences with the use of high-speed digital computers for predicting pattern performance in fluid injection operations and to describe the numerical procedures which have been used for making such analyses. THE NUMERICAL MODEL The problem of representing the reservoir with an appropriate numerical model is composed of at least two important considerations. The first requires that an adequate description of the reservoir mechanism be formulated in the form of the basic differential equation describing the process. The second consideration is definition of the physical characteristics of the reservoir. The latter requires that representative basic data be obtained, examined, and interpreted to provide sufficient detailed definition of the pertinent physical properties throughout the system. The Differential Equation One of the basic assumptions made for the purpose of performing the two-dimensional studies being dis-

THIS chapter and Chapter 19 deal with the heat quantities involved in open-hearth steelmaking, including the thermal efficiency of the furnace as a generator of high-temperature heat, the heat storage in the steel and slag produced and in the furnace walls, and the heats of the various chemical reactions involved in combustion, in the formation of slag, and the refining of steel. The fundamental laws to be considered are the first two laws of thermodynamics as applied to problems involving sensible and potential (or latent) heat only: 1. Heat input equals heat outflow plus storage. 2. Heat may be transferred only from a hotter body to a colder one. The first of these laws relates to the various heat quantities or the heat balance of the process. No one has as yet made an open-hearth heat balance that came out almost exactly balanced. The cause probably lies in the difficulties of accurate temperature and flow-rate measurements at the high temperatures involved and the inherent complexities in flow distribution and air leakage present in any real open-hearth furnace system. Some idea of the magnitude of the heat quantities involved can be obtained by a brief, crude outline of the heat balance of a 90-ton heat of steel. We will assume a 60 to 70 per cent hot- metal charge in a fairly fast working and only moderately efficient furnace, burning fuel oil, with a fuel consumption of around 4 million Btu per net ton of ingots produced. The time from start of charge to tap is 9 hr. During this period, the oil burned represents 360 million Btu and the sensible heat in the preheated air at the port ends is 117 million Btu, so that the total heat input at the ports is 477 million Btu. Heat stored in the steel and slag at the end of the heat, plus the various amounts absorbed by certain bath reactions, amounts to a total of 195 million Btu, but 120 million of this is supplied by the heat in the hot metal and by various heat-evolving reactions in the bath,

Jan 1, 1964

By George A. Morrison

The Columbia Chemical Division of the Pittsburgh Plate Glass Co. is at Bar-berton, Ohio, 35 miles south of Cleveland. For many years large tonnages of limestone have been brought to the Barberton plant from distant points. The stone is here burnt in vertical kilns, the resultant product then hydrated and the hydrated lime used in chemical processing. To eliminate the expense of these shipments, the company decided to investigate a limestone bed known to exist on company property at Barberton, where the stone is used. The bed lay at a depth of more than 2000 ft. and was known locally as the "Deep Lime." Chemical analyses of sludge from churn-drill holes made some years ago proved that the limestone was of sufficient purity to warrant diamond-drill exploration. Four diamond-drill holes were put down at well-spaced intervals, to represent fairly an area of four miles by one mile. Cores logged as to chemical and physical conditions were found to compare closely, and to corroborate the earlier evidence that the limestone was of superior quality for chemical use. A plant of 300 tons per hour was subsequently decided upon. SITe The yard at the chemical plant was already so congested that location of the projected mine within its area could not be considered. Eventually a site was selected 2 miles northwest of the plant, near the main line of the Erie Railroad. Here 412 acres were owned outright by the company and stone rights were obtained on 2 50 additional acres. This location required a transportation line of nearly 2 miles (8800 ft.), crossing two major highways, and to avoid interruption of deliveries to the plant, overpasses were planned. Geology The limestone in the immediate vicinity lies about 2200 ft. below the surface. Geologists* identify this stone as Delaware of Devonian age. It is overlain by 18 ft. of unconsolidated (sand and gravel), 100 ft. of water-bearing sandstone, and finally 2080 ft. of shale into which sandstone in thin layers is interbedded. The contact of shale and limestone is abrupt, flat-lying and very pronounced. Berea sandstone, often found at 520 ft., is absent, but Euclid sandstone was encountered, together with a seepage of oil and a small amount of methane gas. The limestone bed itself is 345 ft. thick, and overlies 200 ft. of gypsum. The lower part becomes dolomitic as it approaches the gypsum. A detailed study of the drill cores indicates that the upper 50 ft. are highest in lime and reasonably low in silica. The physical make-up shows several separating cherty layers. These occur at definite horizons and cause distinct partings, which become horizontal planes of

Jan 1, 1946

By W. Mitchell, B. H. Bergstorm, C. L. Sollenberger

A unique compression testing machine was constructed to load individual 1/8 to I-in. spheres of glass, etc., at rates from 100 to 100,000 lb per min. During loading the applied load was continuously plotted us the deformation of the sphere-platen system. The load-deformation curve conforms to the theory of elasticity. The spheres were surrounded by steel retaining rings or by gelatin (to prevent secondary fracture). The product size modulus was determined from screen analyses. The data shows: 1) Energy input per unit mass is inversely proportional to the product size modulus (or directly proportional to the surface area per unit mass). 2) Increased loading rates slightly increase the energy input per unit mass required for fracture without affecting the preceding relationship. Theory and experiments show that much of the input strain energy is transformed into kinetic energy of fragments at fracture, this being a reason efficiencies based on "surface energies" are exceedingly small. This large kinetic energy component is usually dissipated as heat but may be partially reclaimed because impact of fragments against the surface of steel retaining rings causes additional comminution. There are currently several theories of crushing, all of which can be derived from the general energy equation of Gillilandl as was pointed out by Mitchellet al in 1954'and more recently by Rose and Sullivan. If the exponent of the equation dE-x-"dx is assigned values of 2,1, or 3/2, one obtains by intergration between suitable limits, the equations of Rittinger, kick,' and Bond,' respectively. Other investigators prefer to let the exponent be a variable parameter. To help resolve the controversy, the Allis-Chal-mers Research Laboratories set up a series of carefully controlled experiments in which the level of energy input required to induce the comminution of a single particle by slow compression loading was very accurately measured. The energy input requirement, in conjunction with the size analysis of the fragments produced at fracture, yielded an accurate energy-product size relationship for the conditions studied. APPARATUS The experimental apparatus was designed to apply a compressive load on opposite sides of an "ideal particle." Spherical shapes were chosen, because point contact loading is typical of the mechanics of conventional crushers. The bulk of the experimental data was obtained with glass spheres because glass is a fairly homogeneous, brittle material for which the properties follow definite statistical distributions. The spheres ranged from 1/8 to 1-in. diam. The compressive load was applied to the specimen at a uniform rate by a loading mechanism (Fig. 1) which acted through a system of levers. The uniform rates, ranging from 100 to 100,000 lb per min, were obtained by metering water into a bucket suspended at the end of the secondary level. Point contact was made with the sphere through tungsten-carbide platens. This latter material is extremely hard and has a high modulus of elasticity, thereby having a minimum of distortion when loaded. The actual load on the sphere was measured independently of the lever system by a load cell, Fig. 2, which was designed so that the voltage output of the load cell would be proportional to load. The deformation of the specimen was indirectly measured by a pair of transformers which were attached to opposite edges of the upper platen. The cores of the transformers, which were attached to the lower platen, moved relative to the transformer so that the voltage output was proportional to the deformation of the sphere-platen system. The load was plotted against the deformation on an X-Y recorder. The area under the curve, as shown on Fig. 3, was proportional to the energy input of the

Jan 1, 1961

By Colin Baker, G. C. Smith

Investigation of the initiation and propagation of ductile failure in OFHC copper was undertaken to determine the role of nonmetallic inclusions. The effect of inclusion initiated voids on the formation of the internal cavity and the final shear separation was studied by metallographic eranzination of strained test pieces. A strain anneal technique was used to enlarge the voids under uniaxial stress conditions to elinzinate triaxial stress effects. Measurements of void size us stress and strain were made to show the point at which void im'tiation begins and becomes an important factor in the deformation process. The work of separation of copper-cuprous oxide was determined to attempt to correlate the breakdown of the matrix inclusion interface with void initiation and propagation. The zloid shape and position relative to the tensile axis suggested an interface breakdown mechanisnz of initiation. Evidence is presented that shows a basic similarity between the central cavity propagation and the 45-deg shear portions of the failure. DUCTILE fracture has been studied by a number of workers1-lo and attention drawn to the importance of hard second phase particles in the initiation of the failure. Holes formed at the matrix-particle interface can elongate by plastic deformation and then subsequently expand sideways to link up and produce a major crack. This is usually observed first in the center of the macroscopically necked region of a test-piece where the hydrostatic stresses are at a maximum. As the crack spreads sideways towards the free surface of the specimen, well defined shear zones develop from the crack tip and the final separation is along a direction at approximately 45 deg to the stress axis. This shear failure may also be associated with voids formed adjacent to second phase particles. In this way a cup and cone type fracture is produced. The stage at which separation takes place between particles and the surrounding matrix has not been clearly identified. In addition, although researchers have dealt with anisotropy of tensile behavior" as a result of material fabrication variables, not much is known about the microstructural features of aniso-tropic behavior. In the present work evidence on these points is presented in relation to the behavior of copper containing second phase particles of cuprous oxide. I. MATERIALS AND PROCEDURES EMPLOYED The material used was +-in. diam or 2-in. sq cold-drawn OFHC copper bar which contained 0.6 pct by volume of cuprous oxide inclusions. These ranged in COLIN BAKER, Junior Member AIME, formerly at -mnF of Metallurgy, University of Cambridge, Cambridge, England, is presently Research Scientist Reynolds Metals Co., Richrnand, Va. G. C. SMITH, Member AIME, is Senior Lecturer, Department of Metallurgy, University of Cambridge. Manuscript submitted June 20, 1967. IMD size from approximately 1 to 6 p in length and 1 to 4 p in width. The shape was generally slightly ovoid. Tensile tests were made on specimens having a gage length of 2.5 cm and diameter of 0.643 cm. Metallographic examination was carried out by sectioning deformed and fractured specimens; in addition fracture surfaces were examined optically and with a scanning electron microscope. Some measurements of the work of separation between copper and cuprous oxide were made, using a sessile drop technique which was a modification of that used by Kingery and umenick." The best metallographic results were obtained by using a vibratory polisher, which minimized smearing of the surface. 11. RESULTS A) Initial Experiments. Specimens from the +-in. diam rod were annealed for 2 hr at 650°C in uacuo, at which temperature complete recrystallization occurred without any change in the form of the inclusion. They were then fractured at temperatures from -190" to 600°C. Cup and cone fractures were obtained at all temperatures from -196" to 400°C. With increase in temperature there was, however, a continuous increase in the extent of the central transverse area and a corresponding decrease in the shear portion of the fracture. Above 400°C, the fractures became intergranular. Sections of specimens tested below 400°C revealed extensive small voids which were always associated with inclusions. However, the voids only reached dimensions greater than the inclusion size in the region of the macroscopic neck, where they were many times longer. Lateral expansion was found only near the fracture surface of the test pieces. As observed by Puttick, the voids were either (a) triangular holes initiated in the direction of the tensile axis and elon-

Jan 1, 1969

By W. A. Dunkley, W. W. Odell

The sulfur content of coal is perhaps more important in the manufacture of illuminating gas than in any other coal-using industry. Whether the gas is made by the distillation of coal in retorts or ovens or by steaming incandescent coal or coke in the water-gas process, a portion of the sulfur present in the fuel always passes into the crude gas. Practically all the sulfur that remains in the finished gas is transformed into sulfur dioxide (SO2) when the gas is burned. Sulfur dioxide is a pungent suffocating gas and, if present in the air in any perceptible amount, is deleterious to health and comfort and damaging to house furnishings. SO universally is this recognized that laws regulating the amount of sulfur that may be permitted to remain in the gas are very generally in force. The capacity of a plant to purify gas frequently limits the selection of coal for gas making. This condition may arise from different causes. Some plants were originally designed to handle a certain grade of low-sulfur gas coal, and very little leeway was allowed for growth or for the use of inferior coals. Other plants, when built, had ample capacity to purify gas from relatively higher sulfur coals, but their output has grown so rapidly that their purifying capacity is now limited and only the low-sulfur coals can be handled. There is a great quantity of coal in the United States that would satisfy the requirements of the gas manufacturer, were it not for the high sulfur content. The coals containing less than 1 per cent. sulfur are becoming scarcer year by year and, in time, the gas industry will probably be compelled to use coals that are now considered out of the question. Sulfur Compounds in CRude Gas Sulfur exists in unpurified illuminating gas in a variety of compounds; chief of these are hydrogen sulfide (H2S) and carbon disulfide (CS2). In crude coal gas H2S is usually present to the extent of 0.5 to 2.0 per cent., by volume, equivalent to about 300 to 1200 gr. per 100 cu. ft. of gas. In carbureted water gas, the amount of sulfur compounds depends not only on the sulfur content of the coal or coke used, but also upon cite

Jan 1, 1920

By R. I. Garrod, R. A. Coyle

The shapes and positions of X-ray reflections from specimens of copper, steel, and aluminum alloy haue been examined in the elastic and plastic ranges both while the specimen was under stress and in the unloaded condition. For the aluminum alloy the shape was unaltered by the application of stress either within the elastic limit or in the plastic range provided that no additional plastic strain was induced. In copper the broadening accompanying plastic deformation was very slightly reduced when the specimen was unloaded. A similay but more marked elastic component of broadening was also found for steel, but in this case below the yield stress. Line profiles corrected for instrumental and particle-size broadening indicate very large internal stresses in local regions of the plastically deformed metals. The results are discussed in terms of a recent suggestion that the heterogeneous dislocation distribution between the cells and their boundary walls plays a major role in the peak shifts and broadening of the X-ray reflections. STUDIES of the X-ray line profiles from strained polycrystalline aggregates concentrate usually on one or the other of two main parameters: a) the displacement of the peak of the intensity contour from its position for a strain-free aggregate, or b) the shape of the profile. From peak shifts data can be obtained either on the relation in both the elastic and plastic ranges between applied external stress and average lattice strains in a given (hkl) direction, or, alternatively, on the residual lattice strains which are present after a plastically deformed specimen is unloaded.' On the other hand, the shapes of the broadened profiles from cold-worked metals can be analyzed to separate the broadening produced by small particle size and by heterogeneous lattice strains.' In this paper the terms "size broadening" and "strain broadening'' are used in the general sense adopted by warren.' In the past, apart from two early qualitative observation, it has been customary to examine only the movements of the peaks of the profiles while the specimen is actually under load, since the line broadening induced by plastic strain remains after removal of the external stress. Consideration of the implications of existing data of this type suggests, however, that fruitful additional information on a number of fundamental aspects might be gained by careful examination of whether the X-ray line profile is in fact different in the loaded and unloaded states of the specimen. By taking advantage of the sensitivity and convenience of modern diffractometer techniques it is possible to explore with relative ease the magnitude and importance of any elastic effects which may be superimposed upon the well-known permanent changes in profile. The main aim of the work to be described was thus to investigate this point for typical metals and alloys. For this purpose annealed specimens were extended first elastically and then plastically and the positions and shapes of X-ray reflections were recorded. Initially it was anticipated that prime interest would center on observations within the plastic range; it has been found, however, that small changes in profile sometimes occur both before and after the nominal elastic limit of the material is reached. It is shown that the results obtained have important implications in relation to the structural changes and processes associated with deformation. I) EXPERIMENTAL To enable the diffraction lines to be recorded while the specimen was under uniaxial-tensile stress, a small hydraulic testing machine was designed and constructed for direct attachment to the goniometer of a Philips diffractometer. The specimens, which were machined from 1/2-in.-diam rod and had a central rectangular section 3/8 by 1/16 in. over a gage length of 1 in., were held in the machine by split collets mounted in grooves in the cylindrical ends of each specimen. No special precautions were taken to ensure precise axiality of loading. Constant oil pressure was maintained by a lever and weights system and transmitted to the loading rig by flexible pipe. The actual load on the specimen was measured by a load cell in the machine to an accuracy of * 1 pct. To enable smooth X-ray profiles to be obtained the specimen and machine were oscillated continuously during recording through *7-1/2 deg about the normal half-angle position of the goniometer. The three materials chosen for the investigations were high-purity copper as representative of a ductile fcc metal, a low-carbon steel for a bcc metal, and an aluminum alloy as a material in which the proof stress/ultimate strength ratio is high. Details are as follows. a) Copper. 99.999 pct purity. After machining the specimen surface was polished mechanically and

Jan 1, 1964

By J. J. Gilman

Zinc monocrystals, when compressed nearly parallel to their basal planes (within 20), deform in a new way; and certain deformation markings, called "-bands," are typical of this new mode. Characteristics of these bands are described. Mechanical behavior of low angle zinc monocrystals was investigated in some detail. Recrystallization did not occur upon annealing of banded specimens that were free of deformation twins. -Bands do not seem to be the result of nonbasal slip, but rather, a result of a microbuckling mechanism. u-Bands differ qualitatively and quantitatively from ortho kink bands. A dislocation model, consistent with some of the features of u-bands, is described. THE plastic deformation of zinc monocrystals with slip planes (0001) nearly parallel to the stress axis was studied in this investigation. In a previous investigation, it was shown that some low angle zinc crystals (those with slip planes making angles of more than about 2.5+1° with the compression axis), deform by ortho kinking while others (those with slip planes making angles of less than 2.5+1° with the compression axis) deform in a new way.' This new mode of deformation will be described in some detail here. Some of its striking features are: 1—it operates only for compressive stresses, 2—its temperature dependence is anomalous, and 3—it exhibits a new type of "yield-point" behavior. The mode of deformation to be discussed is not new in the sense that no previous evidence of its existence had been reported. The markings that it creates on the cleavage surfaces of zinc crystals have been described by several investigators.'" However, this is the first time that it has been made to operate under controlled conditions so that its response to mechanical variables, temperature, and aging treatments could be investigated and its geometry completely described. Apparently. Jillson' as well as Holden3 and Pratt" believed that the small bands they observed were simply small versions of ortho kink bands. In fact, two of these authors3,6 "alled the markings "micro kink bands." In spite of the precedence, it is felt that this term is not entirely suitable because these bands do not have the same genesis as kink bands, and they are qualitatively different in structure. As will be indicated by later discussion, the bands seem to be related to the tensile deformation bands observed in aluminum. The present author has chosen to call the bands "micro deformation bands," or simply ",ubands," and the deformation process, ''p-banding." Experimental Methods Crystals were grown from 99.999+ pct Zn obtained from the New Jersey Zinc Co. The details of the technique are given elsewhere." It should suffice to say that the crystals were seeded for orientation control, and precision pyrex tubes were used for molding them. About 40 crystals were used, yielding some 130 specimens. Fig. 1 illustrates the typical form of the specimens and shows how the orientation angles are defined. The crystal specimens were usually 1 3/4 in. long and about 150 mil in diameter. The angle between the slip or cleavage plane (0001) and the specimen axis is designated by xo, while a is the angle between the maximum slope of the (0001) plane and the nearest close-packed direction [1210], vary ing from 0°to 30°. The crystals were cut into specimens with a jeweler's saw and the ends were squared by filing (specimens held in V-block). Crystals of this orientation are stiff toward bending, so this procedure introduced only deformation localized at the ends. Then the specimens were polished either chemically in 50 pct HNO³ or electrolytically in 20 pct chromic acid. The mechanical tests were made with an Instron testing machine. This machine weighs by means of electric strain gages on elastic bars and is quite stiff, since the full-load deflection of its load cells is at most 0.002 in. Most of the testing was done at a

Jan 1, 1956

By E. S. Machlin, Morris Cohen

The martensite reaction in single crystals and polycrystals of 70 pct Fe-30 pct Ni alloys is shown to be autocatalytic in nature, producing bursts of transformation during cooling. The temperature of the first burst of transformation, called Mb, occurs below M, in these alloys. Experiments were devised to test the athermal embryo and strain embryo theories of martensite nucleation. The results indicate that internal strains, either within the virgin austenite or around existing martensitic plates, control the nucleation process in these alloys. Furthermore, the growth of martensitic plates is not limited by the attainment of an elastic balance with the austenitic matrix, but by the occurrence of plastic deformation at the martensite boundaries which interferes with the propagation mechanism. IN an investigation of the martensitic habit in single crystals of a 69 pct Fe-31 pct Ni alloy,' it was observed that about 25 pct of the austenite transformed during subatmospheric cooling within the time-interval of an audible click. This event proved quite spectacular: The shock wave sent out from the specimen freely suspended on a thread in the refrigerating liquid was occasionally sufficiently intense to shatter the Dewar container and to separate the toluene column in the immersed thermometer. The Present investigation was undertaken to determine- the kinetics and mechanism of this "burst" type of martensitic reaction. The analyses of the alloys studied are given in Table I. The composition of the single crystal specimens is designated by alloy A, while the polycrystal-line specimens were made of alloys B and C as noted in the text. The single crystals were prepared in a vacuum furnace, using a modified Bridgman technique. Most of these crystals were homogenized by holding for 24 hr at about 1300°C just after solidification. However, it may be emphasized here that the degree of homogenization was not a controlling factor in the subsequent experiments, inasmuch as specimens having different degrees of homogenization yielded the same results. All of the single crystals were fully austenitic as slowly cooled to room temperature. An illustration of the burst phenomenon is given in Fig. 1, which shows oscillograms of electrical resistivity and temperature vs. time during the continuous quenching of 1/16 in. wire specimens (alloy B) in a dry ice and acetone bath at —77°C. There are at least two observable bursts in this case, as indicated by the sharp decreases of resistance accompanying the sudden formation of substantial quantities of martensite. The thermal arrest during the quench probably corresponds to the larger burst. Usually the bursts are followed by more or less progressive transformation during continuous cooling. It will also be noted that the resistance continues to decrease after the specimen has reached the bath temperature. This isothermal change denotes the formation of martensite at constant temperature, and will be the subject of another paper. Examination of fiducial scratches on the surface of a transformed single crystal has shown2 that the scratches in adjoining nonparallel martensitic plates are usually bent in opposite directions, as though one plate forms in such a way as to relieve the matrix stresses set up by the adjacent plate. This, together with some of the results described in ref. 1, Table I. Compositions of Alloys Studied, in Percent Alloy Ni C N Mn Si P S Cr A 31±0.3 0.048 0.027 0.003 0.56 0.007 0.002 B 29.5±0.2 0.036 0.02 0.19 0.09 0.008 0.006 C 19.99 0.52 0.37 0.47 0.010 0.015 0.04 led to the tentative concept that a cooperative action exists which provides the impetus for much of the transformation that appears during the burst. The following series of experiments were performed in order to test this idea. Cooperative Nature of the Burst Two adjacent disks, Va in. thick x % in. diam, were cut from a single austenite crystal of alloy A using a jeweler's saw. One of the disks was then cut into 15 parts. Then 12 of the latter pieces and the second disk were austenitized (stress relieved) at 600°C for 30 min and water quenched to room temperature. The temperatures at which the first burst of transformation appeared were determined for

Jan 1, 1952