Search Documents

By Gilbert Thiessen

The use of a pneumatic process for removing fine material (usually less than 48-mesh) is increasing in the preparation of stoker-size coal. The fine material, produced as a byproduct, is known as dedusting-plant dust. Since fusain is the most friable ingredient in bituminous coal (it may readily be rubbed to an impalpable powder with the fingers), it tends to accumulate in this byproduct. While studying the properties of cokes produced by blending Illinois coals with other materials, considerable quantities of fusain were required. Dedusting-plant dust suggested itself as a convenient supply. It became necessary, therefore, to determine how much fusain was contained in a measured sample of dust, how the fusain was distributed with respect to size and specific gravity in the sample, and whether or not it would be feasible or desirable further to concentrate or to recover the fusain from the dust before using it in the blends to be coked. The results obtained indicate the possibilities of production of a high-fusain material. Previous Work Lehmann and Stach have developed a processl,2 for separation of banded bituminous coals into their band ingredients by impact pulverization followed by screening or air separation. They found, as might be expected, that the fusain was concentrated in the very fine material. Prockat and Raute3 examined samples from dedusting plants operating in the Ruhr. They separated the dust into various screen sizes and determined the composition of each of these sizes in terms of the banded ingredients of the original coal. In the dusts examined by them, the finest material was always high in fusain, and most of the fusain contained in the original samples could be recovered from this fraction.

Jan 1, 1936

By I. Zaplatynskyj, G. C. Kuczynski

SINCE the excellent studies of metal powder compaction executed by Kamm, Steinberg, and Wulff, no work on the subject has appeared in the technical literature. Kamm et al. were the first to investigate quantitatively the distribution of density in a powder compact, as a function of pressure, height and diameter of the die, powder particle size, etc. For this purpose they devised a very ingenious method. They inserted a thin lead grid into a die and then filled the die with powder. During cold pressing, the lead grid -moved downward. Due to its deformability it followed closely the downward descent of the adjacent powder. The die was then radiographed and, from the deformations of the grid openings measured on the radiographs, the density in the vicinity of each opening was evaluated. Their findings led them to the conclusion that the friction on the side walls of the die is a major controlling factor of the density distribution inside the cold pressed powder compacts. However, it is difficult to conduct tests similar to those of Kamm, Steinberg, and Wulff in a processing plant laboratory, which usually lacks the necessary expensive radiographic equipment. The purpose of this note is to describe a method which makes it possible to determine the density distribution in green powder compacts with the same accuracy as the lead-grid method but which is far simpler and faster and requires only standard laboratory equipment. Instead of using a lead grid, the hardness at selected points of the sectioned compact is determined. If the relationship between hardness and density is known the density distribution is readily obtained. This relationship is easily found from measuring hardness and densities of thin compacts. In such compacts the density, for all practical purposes, is constant throughout. The method was tested on a Plast nickel powder, grade FlA-A20, kindly supplied by Plast Metals Co. Thin compacts (height to diameter ratio 0.2) were pressed in a single action cylindrica1 die at various pressures. The density of the compacts was determined by weighing and by measuring the height and diameter with a micrometer. Subsequently the Rh hardness was determined. Up to ten readings were taken on each specimen. The difference in hardness readings on each compact was never greater than three corresponding to about 0.1 g per cu cm uncertainty in density. By varying the compaction pressure of the samples, a whole scale of densities was obtained allowing construction of a set of density-hardness calibration curves. To test the method several compacts of different height were pressed under varying pressures. Die walls were always well lubricated. After pressing, the compacts were mounted in bakelite and halved by grinding, and hardness readings taken along the diameters of the specimens. The distance between adjacent indentations was about 2.5 mm. After hardness readings were translated into densities, contour maps of densities of the compacts were prepared. One of them is reproduced in Fig. 1. The areas encompassed by the curves are labeled with numbers representing the density in g per cu cm of those regions. In Fig. 2 the same results are re-plotted to emphasize the radial density changes at various depths. The results thus obtained confirm the findings of Kamm, Steinberg, and Wulff kentioned previously. They are recapitulated here briefly. 1—The densest part of a compact pressed from one side is at the outer circumference at the top and the least dense part at the bottom, at the outer circumference. Figs. 1 and 2 show this clearly. 2—The density near the cylindrical surfaces of the compact decreases uniformly with height from top to bottom. 3—The density variation increases with the height to diameter ratio. References R. Kamm, M. A. Steinberg, and J. Wulff: Trans. AIME (1941) 171,'R. p. 439 ;MetaLs Technology (February 1941). R.p. Kamm, M. A. Steinberg, and J. Wulff: Trans. AlME (1949) 180, 2R.P. 694; MetalS Technology (December 1948).

Jan 1, 1957

By Dennis E. Stover

Grade control for in situ uranium leaching is maintaining, at desired levels, the uranium concentration in the pregnant lixiviant which feeds the extraction (ion exchange) circuit. This differs from grade control in conventional mining in that in situ grade control is imposed subsequent to rather than prior to leaching without the direct observation and control possible in conventional mining and milling. Grade control is a necessary engineering task through the entire project life, beginning with preliminary evaluation and design and ending only when the final wells are shut in. More specifically, this task is associated with designing the initial well field, maintaining productivity during well field operations, and planning well field expansions to compensate for the depletion of existing wells. Our aim during each of these phases is to maximize uranium productivity while ensuring that we are developing information necessary for future phases. Throughout this task, we remain cognizant of the fact that uranium productivity is a function of both the complex geologic and operational parameters of the project. A minimum list of significant geological factors must include the following: . Host formation mineralogy . Uranium mineralogy . Permeability . Ore quality (grade and thickness) Our concerns are not limited to average or general descriptions of these factors. The interactions among the factors as well as localized variations among them are far more important in obtaining high productivity from a deposit. For example, an ore body may display an average permeability of one darcy but have its high grade ore confined to regions with permeabilities less than 500 millidarcies. This relationship between ore grade and permeability must be understood early in the project life if the operation is to be successful. Similarly, the fundamental operating parameters for the well field include those items which enable us to distribute the lixiviant within the ore as well as the chemistry which will dissolve the uranium minerals. A minimum list of such factors will include: . Well design . Well efficiency . Well bore damage . Pattern size and shape . Oxidant type and concentration . Complexing agent concentration - pH The interactions between these variables and the complex geological variations create a situation which often defies quantitative analysis. Hence, we have adopted a statistical approach when correlating production history with these parameters and the quality of the correlations improves as the number of wells operated increases. However, the correlations are often specific to an ore body. We find that we must tailor the process to meet the unique geologic parameters of each ore body. PHASE 1: INITIAL WELL FIELD DESIGN Designing the initial well field is perhaps the most difficult phase because we have the smallest data base from which to predict performance. We will have conducted numerous laboratory tests and, perhaps, field pilot tests to select the lixiviant system and to characterize the geologic parameters. However, we will learn a great deal more about the deposit and its productivity during actual commercial scale operation. Fully acknowledging its limitations, we will, as a starting point, assume that uranium productivity will be directly proportional to the quality and quantity of recoverable reserves. Future deviations from this assumption will be plentiful and result from our limited understanding of the aforementioned interactions between and among the operational and geological factors. However, in planning the initial field, estimation of the quantity of leachable uranium present at levels above the economic grade and grade-thickness limitations is a priority task. (The concentration of uranium in the ore, the ore grade, is expressed in units of weight percent. The grade-thickness of the ore is the product of the average grade and ore thickness expressed in units of percent-feet.) These parameters provide a direct indication of the quality and quantity of ore. They are determined from gamma logging of closely spaced drill holes (50 to 100 foot centers being typical) accompanied by uranium core analysis or direct uranium assay logging. Gamma- logging measures gross gamma radiation which emanates from uranium decay products and indicates only the possible presence of uranium. Direct uranium assays are necessary to confirm this presence and the true location and quality of the reserve. From this information, an estimate of the in-place uranium reserve is formulated. Utilizing the above data, we begin to assess the quantity and quality of the leachable reserve. Analysis of self-potential and resistivity logs in conjunction with uranium logs will identify those zones which contain uranium and display apparent high permeabilities. Similarly, zones with extensive calcite cementation or dense clay sedimentation are located and uranium within such zones is excluded. (Interpretation of these logs should be confirmed

Jan 1, 1980

By M. E. Wadsworth, K. J. Richards

The oxidation rates of tantalum in various partial pressures of carbon dioxide in the temperature range 700°to 950°C were measured with a thermo-gravimetric balance. Oxidation involved a surface -controlled reaction associated with the formation of a nonprotective layer of Ta2O5. Below about 720°C, there was a change in the rate-determining mechanism, and above 830°C the linear rate was preceded by a complex region of nonlinear oxidation behavior. The linear oxidation of tantalum has been explained quantitatively in terms of carbon dioxide adsorption, followed by a rate-controlling surface reaction. The initial adsorption has been expressed both as an equilibrium process and as a steady-state reaction. The enthalpy for chemisorption of CO, was determined to be -17.3 kcal per mole. The surface-controlled reaction had an activation enthalpy of 40.4 kcal per mole. A considerable amount of interest has been shown in recent years in the oxidation of tantalum and the nature of the oxide film produced. This interest is associated with the increasing demand in our technology for structural materials to withstand high temperatures and corrosive atmospheres. The low oxidation resistance of tantalum has severely restricted its application as a high-strength, high-temperature material. As a fundamental approach to the realization of the full poten- tials of this metal, the kinetics of the oxidation of tantalum in oxygen and air have been extensively studied; however, very little work has been reported on the effect of other gases, including carbon dioxide. According to Miller,' the only reported study of the reaction between tantalum and dry carbon dioxide is a restricted observation by O'Driscoll et al.2 at 8 atm absolute pressure and 500°C. Therefore, this study was made to investigate the reaction of tantalum with carbon dioxide. EXPERIMENTAL MATERIALS AND METHODS The vacuum-annealed tantalum used in this study was obtained from Fansteel Metallurgical Corp. as 0.025-mm-thick sheet stock. This material had less than 0.1 pct total impurities, and the maximum individual impurity concentrations were

Jan 1, 1964

By N. A. Zeigler, T. D. Yensen

Aging is a term that connotes a slow change in properties under ordinary operating conditions. It can be accelerated by increasing the temperature and by mechanical straining. The magnetic properties of iron and some of its alloys have for many years been known to be subject to such a change. But the cause of the change was not recognized until a few years ago after mechanical age-hardening in non-ferrous alloys of the "duralumin" type had been definitely shown, by means of solid solubility curves, changes in electrical resistance and microanalysis, to be caused by slow precipitation of one or more constituents from the solid solution. The similarity between the solid solubility curves of such alloys (Fig. 1) and those for iron-nitrogen (Fig. 2) and iron-carbon alloys (Fig. 3) below the A1 transformation point suggested at once that magnetic aging of iron might be caused by a similar process; namely, by the slow precipitation of carbon and nitrogen in the form of Fe4N and Fe3C at ordinary temperatures because of a cooling rate that had been too rapid to permit complete precipitation according to equilibrium conditions. This suggestion has since been amply confirmed, particularly by the comprehensive work of Köster1 on the effect of nitrogen and carbon. Typical curves are shown in Fig. 4 for the relationship between aging temperature and coercive force. Previous to the establishment of the precipitation-hardening theory it was thought that the effect of nonmetallic elements like C, N, O, etc., on the magnetic properties of iron was greatest when these elements were retained in solid solution, atomically dispersed throughout the interstitial spaces of the iron lattice2. Based on the theory that magnetic properties are intimately connected with the regularity of the lattice, it now follows quite logically that a greater effect on this regularity may be obtained when the above impurities are precipitated as very fine particles of Fe3C, Fe4N, FeO, etc., more or less uniformly dispersed within the grains. But if this is the case, it follows also that there must exist a relationship between the size

Jan 1, 1935

By N. A. Zeigler, T. D. Yensen

Aging is a term that connotes a slow change in properties under ordinary operating conditions. It can be accelerated by increasing the temperature and by mechanical straining. The magnetic properties of iron and some of its alloys have for many years been known to be subject to such a change. But the cause of the change was not recognized until a few years ago after mechanical age-hardening in non-ferrous alloys of the "duralumin" type had been definitely shown, by means of solid solubility curves, changes in electrical resistance and microanalysis, to be caused by slow precipitation of one or more constituents from the solid solution. The similarity between the solid solubility curves of such alloys (Fig. 1) and those for iron-nitrogen (Fig. 2) and iron-carbon alloys (Fig. 3) below the A1 transformation point suggested at once that magnetic aging of iron might be caused by a similar process; namely, by the slow precipitation of carbon and nitrogen in the form of Fe4N and Fe3C at ordinary temperatures because of a cooling rate that had been too rapid to permit complete precipitation according to equilibrium conditions. This suggestion has since been amply confirmed, particularly by the comprehensive work of Köster1 on the effect of nitrogen and carbon. Typical curves are shown in Fig. 4 for the relationship between aging temperature and coercive force. Previous to the establishment of the precipitation-hardening theory it was thought that the effect of nonmetallic elements like C, N, O, etc., on the magnetic properties of iron was greatest when these elements were retained in solid solution, atomically dispersed throughout the interstitial spaces of the iron lattice2. Based on the theory that magnetic properties are intimately connected with the regularity of the lattice, it now follows quite logically that a greater effect on this regularity may be obtained when the above impurities are precipitated as very fine particles of Fe3C, Fe4N, FeO, etc., more or less uniformly dispersed within the grains. But if this is the case, it follows also that there must exist a relationship between the size

Jan 1, 1935

By W. Blake McCullogh

It is often written that the purpose of any mining operation is to produce efficiently, safely, and profitably, and always to search for more efficient, safer, and more profitable methods. To provide for continual improvement, an attitude that is not only reasonable but also imperative, there is an obvious need for a high standard of competence among the ranks both of supervision and of those being supervised. It naturally follows that, to achieve this standard, planned training in every level of an organization is a definite necessity. There are many factors involved in the need for training, and the scope of a program is influenced by answers to such questions as: "What is the geographic location of the project?" "What are the duties of each job?" "What is the source of the working force and supervision?" "What are the hiring standards for various jobs?" "What is the availability of trained personnel?" "What is the availability of outside training facilities?" The approach in this chapter will be to consider a need for a maximum of training, and it may be applied by the reader to whatever extent is considered necessary in each individual situation. 14.2-1. Administration. It is a basic responsibility of every supervisor at all levels to train those who work for him. However in a very extensive training program, which involves supervisors and the working force, includes both compulsory and voluntary participation, uses outside and in-plant methods, and where the increasing complexity of jobs requires more specialization, the establishment of a training department is definitely war- ranted. This will consist mainly of instructors for related classroom training and preparation of manuals, etc., and the necessary clerical help. A training staff does not relieve the various departments of their responsibility to train, but it does have facilities, experience, and contacts that are inval-

Jan 1, 1968

By James R. Dunn

The purpose of this chapter is to review the uses of sand and gravel by the construction industry. The specific intention is to give tech¬nical people the general perspective and frame¬work which they need to help in making tech¬nical and business decisions. In the sand and gravel industry such decisions are based on an understanding of sociologic, economic, and technologic factors. In order to discuss the sand and gravel industry intelligently, it is necessary to define sand and gravel. "Sand" as most often used by industry is not sand in an engineering or geo¬logic sense but should be called "natural fine aggregate." The expression "fine aggregate" is preferable to "sand" because fine aggregate in¬cludes grain sizes which, according to engineer¬ing or geologic classifications, are defined as pebble or grit size. Natural fine aggregate is distinguished from manufactured fine aggregate in that the manufactured material is crushed and screened to produce the required sizes and natural fine aggregate is only screened. Coarse aggregate is generally defined as aggregate which will not pass a No. 4 or %o-in. sieve. Coarse aggregate may be natural (gravel) or manufactured (crushed stone, crushed gravel, slag, or coarse lightweight aggregate). Gravel is usually considered sufficiently crushed to qualify as manufactured coarse aggregate when two or more sides are broken. Sand and gravel (crushed or uncrushed) is used in asphaltic and portland cement concretes, is subbase for pavements, as fill where good drainage is needed (such as around structures), and for many other uses. About 96% of all he sand and gravel produced is used in construction.

Jan 1, 1975

By Carl G. Hogberg

DURING recent months, the acute shortage of steel scrap has necessitated the use of higher percentages of hot metal in the open-hearth charge. With these higher percentages, the sulphur content of hot metal has become an increasingly important factor in the control of the quality of steel. Thus, the blast-furnace operator is faced with a demand not only for more output but for a higher quality of product. More than go per cent of the sulphur charged into the blast furnace is contained in the coke. With the tremendously increased demand, the trend of coke quality has been toward higher sulphur, higher and more variable ash, and poorer physical characteristics. This has been brought about by less selective coal mining, increased production rates in coke plants and resumption of operations of many beehive ovens. In a single month last year, one blast-furnace plant in the Pittsburgh district operated with coke obtained from 52 sources. The effect of variability and quantity of coke ash on blast-furnace operation is well known. The improved results obtained with furnaces operating on coke made from washed coals compared with results on coke made from raw coals is ample proof of the effectiveness of low and uniform ash. Coal-washing plants, however, require a large capital expenditure, and are impractical for most of the large number of small producers, whose operations are confined chiefly to periods of abnormally high demand. Furthermore, not all coals are physically adaptable to washing. PRINCIPLES OF IRON DESULPHURIZATION IN FURNACE Although investigations of the blast-furnace process have not clearly revealed the detailed mechanism of iron desulphurization within the furnace, they have been sufficiently extensive to permit a postulation of the following general principles: I. Iron, in its travel from furnace top to hearth, continues to pick up sulphur until it has reached tuyere level. The zone of iron desulphurization is relatively narrow, being confined to a vertical distance extending approximately from tuyere level to the iron-slag interface in the hearth.1 2. Combustion of coke is confined to spherical zones extending approximately 40 in. from the nose of each tuyere.2 Coke ash is released as the coke burns in these combustion areas. 3. With a constant amount of sulphur in the charge, the sulphur content of the metal product is a function of hearth temperature, final slag analysis, slag viscosity, and slag volume. Both hearth temperature and slag analysis affect slag viscosity. For a slag of constant analysis, viscosity always decreases with an increase in temperature;

Jan 1, 1943

By Pradeep K. Rohatgi, Clyde M. Adams

An analysis of heal conduction in the freezing of a solution has been performed. The case considered is the semi-infinite mass of solution, bounded by a con-stant-temperature plane with one-dimensional heat flow, Numerical cooling rate and freezing rate distributions hare been calcutated for the particular case of unidirectional freezing of aqueous solutions against. a cold copper chill. The solution at each level parallel to the chill surface is subjected to a spectra of frcezing rates; the freezing rate is inilially lour., passes through a maximum, and then decreases until solidification is camplete. Arange and maximum freeeing rates are inversely proportional to the square of distance from the chill surface. The temperature of the chill surface in contact with the solution remains constant during solidification. Experimentally, it is observed that deudrite sparing increases linearly with distance from the chill surface; in the light of heat -flow analysis this means that the dendrile spacing is imersely proportional to the square root of the maximum freezing rate. SOLIDIFICATION of liquids is accompanied by rejection of latent heat at the solid-liquid interface. The over-all rate of liquid to solid transformation is governed by the rate of heat extraction. Analysis of the heat transfer in the liquid during freezing is important since it determines the freezing rate and resulting structure. A considerable amount of work has been done on metallic systems since solidification is frequently a major step in processing metals. Unidirectional freezing from heat sinks has been treated by several investigators.1-4 Much of the work has been limited to the simpler case of substances such as pure metals which freeze isothermally at a unique transformation temperature. In this case the thickness of the solid zone y, next to a chill surface. is a parabolic function of the time. 8. where a and b are constants. Eq. |1| is a close approximation giving the progress of solidification for the case in which there is a small but finite thermal contact resistance at the interface between the freezing liquid and the chill.' It has been used with some success in connection with large steel ingots4 when the therma1 contact resistance is negligibly small (as is the case when water is brought into contact with the metal chill). The constant, b. becomes zero and Eq. [l] is then exact. even when the thermal properties of the chill and the freezing liquid depend on temperature. Analysis of unidirectional solidification of solutions is more complicated since the latent heat is evolved over a range of temperatures. Next to the all-solid zone in contact with the chill surface there is a solid plus liquid zone in which solidification takes place. Although the equations presented are considered quite general the numerical and experimental results are for freezing of aqueous solutions from a copper chill. I) EXPERIMENTAL PROCEDURE Solutions of potassium chloride, sodium chloride. and lithium chloride have been used. These solutions form a eutectic: a typical phase diagram is shown in Fig. 1. A solution at its liquid us temperature is poured into a tygon tube mounted on a relatively large copper chill. The chill is immersed in a freezing mixture of dry ice and acetone at -70°C. A thermocouple connected to a high-speed recorder was mounted near the top of the chill to measure the fluctuation in the temperature of chill surface in contact with the solution. In this system the progress of solidification can be visually observed through the tygon tube. After the specimens freeze to a desired height they are removed from the copper chill and stripped from the tygon tube. Longitudinal and transverse sections are cut from the specimen for micrographic examination. Specimens in the form of a thin slice are mounted on a transparent glass slide by freezing small drops of water around the periphery. They are then polished on a series of emery papers; the final finishing is done on a soft tissue paper. A Leitz Biological microscope was used for structural observations; photography was

Jan 1, 1968

By Alexander Squire

A brief study of the effects of material and processing variations upon the tensile properties of steel formed from mixtures of iron and carbon was made in order to provide information regarding the properties obtainable in iron-carbon compacts as influenced by forming pressure, sintering temperature, and graphite particle size. Sintered steels formed from mixtures of iron and graphite have been studied by Stern,' who investigated the effect of various percentages of graphite on compacts formed from electrolytic iron that were repressed and heat-treated after sintering. A further study, by Stern and Greenberg,l is concerned with the heat-treatment of steels formed by the car-burization of iron compacts, and Margolies3 has reported work on the simultaneous sintering and carburization of iron-powder parts. Glauch4 investigated the effect of various types of graphite on the properties of iron-carbon powder alloys but did not determine the effect of different particle sizes of the same graphite alloyed with different types of powder. In the investigation reported in this paper, powders typical of those produced by electrolytic deposition and the decar-burization of shotted steel scrap were used. The powders were mixed by tumbling in a jar mill with graphite powder ground to an average particle diameter of 2, 4, 6, and 16 microns (as determined by microscopic measurement). The properties of the iron and graphite powders are presented in tabular form as Table I. In order to obtain the maximum information from a minimum number of test specimens, the study was divided into two sections with one set of specimens treated identically in each section as a basis for comparison. In the first section, iron powder produced by the shotting and subsequent decarburization of scrap steel was mixed with 2-micron graphite powder, pressed at 50,000, 100,-000, and 200,000 psi, and sintered in hydrogen at 1200°C for the periods of time ranging from 15 to 120 minutes. In the second section of the investigation, electrolytic iron powder was mixed with graphite of an average particle diameter of 2, 4, 6, and 16 microns, pressed at 100,000 psi, and sintered at temperatures ranging from 1000° to r200°C'. for periods of time of 30 to 180 minutes. By following this procedure an indication of the effect of the following variables upon the density and tensile properties of iron-carbon powder compacts was obtained: (I) forming pressure, (2) sintering time, (3) particle size of graphite powder, (4) sintering temperature, (4) type of iron powder.

Jan 1, 1947

By Alexander Squire

A brief study of the effects of material and processing variations upon the tensile properties of steel formed from mixtures of iron and carbon was made in order to provide information regarding the properties obtainable in iron-carbon compacts as influenced by forming pressure, sintering temperature, and graphite particle size. Sintered steels formed from mixtures of iron and graphite have been studied by Stern,' who investigated the effect of various percentages of graphite on compacts formed from electrolytic iron that were repressed and heat-treated after sintering. A further study, by Stern and Greenberg,l is concerned with the heat-treatment of steels formed by the car-burization of iron compacts, and Margolies3 has reported work on the simultaneous sintering and carburization of iron-powder parts. Glauch4 investigated the effect of various types of graphite on the properties of iron-carbon powder alloys but did not determine the effect of different particle sizes of the same graphite alloyed with different types of powder. In the investigation reported in this paper, powders typical of those produced by electrolytic deposition and the decar-burization of shotted steel scrap were used. The powders were mixed by tumbling in a jar mill with graphite powder ground to an average particle diameter of 2, 4, 6, and 16 microns (as determined by microscopic measurement). The properties of the iron and graphite powders are presented in tabular form as Table I. In order to obtain the maximum information from a minimum number of test specimens, the study was divided into two sections with one set of specimens treated identically in each section as a basis for comparison. In the first section, iron powder produced by the shotting and subsequent decarburization of scrap steel was mixed with 2-micron graphite powder, pressed at 50,000, 100,-000, and 200,000 psi, and sintered in hydrogen at 1200°C for the periods of time ranging from 15 to 120 minutes. In the second section of the investigation, electrolytic iron powder was mixed with graphite of an average particle diameter of 2, 4, 6, and 16 microns, pressed at 100,000 psi, and sintered at temperatures ranging from 1000° to r200°C'. for periods of time of 30 to 180 minutes. By following this procedure an indication of the effect of the following variables upon the density and tensile properties of iron-carbon powder compacts was obtained: (I) forming pressure, (2) sintering time, (3) particle size of graphite powder, (4) sintering temperature, (4) type of iron powder.

Jan 1, 1947

By Rex W. Woods

The clue history of performance of a highly volatile type oil reservoir which is now greater than 80 per cent depleted is presented. The reservoir is at a depth of approximately 8,200 ft and includes an area greater than 7,500 acres. The reservoir has been exploited by 10 wells which to date have yielded about 10,880,000 bbl of stock tank oil by pressure depletion. Reservoir pressure has declined from an original of 5,000 psi to approximately 1,450 psi. Produced gas/oil ratio has increased from 3,200 to 23,000 cu ft/bbl with a corresponriing increase in APl gravity of the stock tank oil from 440 to 620 . Pressure and fluid data are given for different stages of depletion. INTRODUCTION In papers by Sloan,' and Cook, Spencer and Bo-browski,' properties of highly volatile type reservoir oil were discussed in detail and methods were presented for predicting performance of reservoirs containing this type of fluid. The purpose of this paper is to present performance history of a highly volatile type oil reservoir designated as Reservoir A which has been produced by pressure depletion and field separation without processing of gas GEOLOGY The reterence field which includes Reservoir A is a structural feature north of a trend of major folding along a northeast-southwest axis. In the area of development, the structure has the appearance of a dome with formation dip of three to four degrees, but structural relations between the reference field and the axis of major folding to the south have not been determined. No faulting within the field is evident. Oil and gas productive sands have been found at depths of 7,000 ft to 10,000 ft in a columnar section of Mio-Oligocene age. The sand bodies in the section are lenticular and usually continuity of sand is limited to a small area. Sand A which forms Reservoir A at a depth of 8,200 ft, however, has exceptional continuous development in the reference field. Fig. 1 shows an isopachous map of net oil sand for Reservoir A. Net thickness of oil sand at producing wells ranges from 14 to 34 ft with an average of 22 ft. Pinch-out of sand has been shown by drilling in the southwest part of the field, but extent of the reservoir on the northwest and northeast parts of the field is indicated only by thinning of the sand. The vertical oil column between the highest and lowest producing well in the reservoir is 339 ft. No water-oil contact has been found within the reservoir. As interpreted from the isopachous map, the reservoir includes about 8,900 acres with an average net sand thickness of 12 ft. Because of limited data on extent of the reservoir, the isopachous map permits only an approximation of sand volume in the reservoir. DEVELOPMENT AND PRODUCTION Reservoir A was discovered during 1938 and was developed with eight wells to the end of 1942. One well was completed during 1946 and the tenth well in the reservoir was completed during 1951. Three of the original wells and the last completion have produced from Sand A only. Six wells have produced from Sand A through the casing side of dual completions. Initial producing rates of the original wells ranged from 800 to 1,000 BOPD. Production history for the reservoir is shown in Fig. 2. Production of the reservoir was begun during 1940 and in May, 1952, peak production from seven wells was 5,300 BOPD. At the end of March, 1954. cumulative production was 10.880,000

Jan 1, 1956

CHARGING of an open-hearth heat is begun as soon as possible after the previous heat has been tapped. Ordinarily, about 40 min is required to drain and dress the furnace hearth, make up the taphole, and perform routine repairs of the banks. Repairs to the upper back wall and to the front wall and jambs can ordinarily be done while the first scrap charge is being heated and are therefore allowed to wait in order to save furnace time. Any major repairs required on the hearth or other parts of the furnace necessitate longer delays because such repairs must be made while the furnace is empty. Although charging practice varies considerably in detail with the type and proportions of scrap and iron used, many factors are common to all varieties of charge. Such general considerations are dealt with first. CHARGING EQUIPMENT AND STOCK HANDLING The physical equipment available for loading and weighing the stock, transporting it to the furnace, and charging it, may have a major effect on charging practice. Limestone, scrap, and all other solid melting stock are charged mechanically by means of equipment illustrated in Fig 2-1. The charging of hot metal is shown in- the background of this figure. Mechanical equipment and plant layout for stock handling are described in Chapter 1. It is generally desirable to charge the scrap about as fast as the physical volume can be put into the furnace. Charging scrap that is too heavy or adding the charge too rapidly (less than 45 min) may be detrimental to melting rate because of excessive chilling of the entire furnace system and also because of poor conduction of heat to the lower layers in the furnace; but the more common problem is the reverse one of charging light scrap fast enough to maintain a normal heat time. A limiting factor may be the height to which the scrap may he piled in the fur-

Jan 1, 1964

By W. Robert Power

Dimension stone is considered by many the premium material for beauty and durability in institutional and monumental construction. Nonetheless in the United States it commands an ever decreasing share of the total market. At the beginning of the century dimension stone accounted for more than half the stone produced in the United States, but by 1974 it accounted for little more than 0.2% and the number of producing quarries and finishing plants had greatly reduced. This decrease in use is accounted for in part by competition from cheaper materials, but another factor seems to be the demand by many designers for uniformity and exact repetition of modular units in construction. Even where stone is used in large buildings modem architects want blandness of pattern and uniformity of color in the stone. Because most natural stone contains variations in color and pattern great strain is put on the quarriers to overcome this and produce a uniform product. This results in increased costs, increased waste at the quarries, and consequently increased price in the market. In spite of this, stone is still looked on as the most prestigious of building materials and its aesthetic appeal is born out by the many simulated stone patterns found in synthetic materials. End Use and Specifications The principal uses of dimension stone are in building construction and monuments. Other uses include flagging, curbing, paving, mill-stock slate, roofing slate, laboratory furniture, and refractory brick. Because many of these uses overlap, an orderly classification of dimension stone uses is most difficult. Various classifications have been used by Cumer (1960), Barton (1968), the U.S. Bureau of Mines yearbooks, and the Building Stone Institute (Anon., 1972).

Jan 1, 1975

By J. Stubbins

1 1.4-1. Source of Water. Precipitation in the form of rain or snow is the original source of water that enters most surface mines. The precipitation, which does not escape to the atmosphere, either becomes surface run- off or infiltrates into the ground to become ground water (3,4). Evaporation and surface run-off can be measured. The water that infiltrates the ground disappears from view and is more difficult to evaluate. In general, it moves in a pattern similar to the surface run-off, but at a much slower rate, since its progress is impeded by many subsurface conditions. The infiltrating water descends through the soil and rock by whatever passageways permit flow until the water table or top of the zone of saturation is reached. Though usually pictured as a level surface, it is dependent upon the topography and the permeability of the enclosing material, and therefore it can be as erratic and unpredictable as the subsurface geology. Ground water may become surface run-off again at a lower point, and likewise, surface run-off of lakes and streams can infiltrate to become ground water. Should the ground water be confined to a permeable zone overlain by an impermeable barrier, a pressure is created. Such water is said to be artesian if the pressure head is sufficient to raise the confined water to the surface. These conditions are more commonly found in relatively flat-lying bedded formations. 11.4-2. Recognition and Estimation of Water. Dewatering and flood control should be considered by the design engineer at an early stage in all surface mine planning. Recognition of the possible problems, and making allowance for their solution, is an inexpensive precaution. Circumstances which should lead to investigation are: 1. High rainfall 2. Experience of other mines in the area 3. Evidence of water and caving in drill holes 4. Presence of springs and artesian wells 5. Geological evidence of aquifers.

Jan 1, 1968

By John Birkinbine

In a former paper* attention was directed to the various forms of pumping machines employed for permanent work in mining and metallurgical processes. The following is simply a collection of memoranda of work done of a temporary character, and is presented by way of comparison with other work of similar nature. In close proximity to the charcoal fnrnace at Pine Grove, Cumberland County, Pa., is a large deposit of superior hematite iron ore, which has been worked for a number of years, and from which many thousand tons of ore have been taken by open pit workings. In July, 1874, the furnace was blown out and operations at the bank suspended, the machinery for draining being removed except a plunger pump, 18 inches in diameter and 66 inches stroke, operated by a steam-engine by means of rods. The pit was allowed to fill with water, and no steps towards its reclamation were taken until November, 1877. At that time the pit was a pond of water at the base of the mountain, having an area of about four acres and a depth of seventy feet. As the pumps, rods, etc., had been submerged for over three years, and partially buried by the mud washed down from the banks, and as it was determined to change the location of the pump for future operations and drive it by water-power, a temporary pumping apparatus was determined upon for reclaiming the pit and keeping it drained until the permanent arrangements could be completed. By opening an old adit about 10 feet of the water was removed, and the area decreased to three acres. The inflow of springs was found to be 250 gallons per minute, and the amount of water contained in the pit was computed to be 45,000,000 gallons. As the inflow would undoubtedly increase while the water sank in the pit, provision was made for removing at least 60,000,000 gallons, at the rate of 1,500,000 to 2,000,000 gallons per day. The company determined to employ a Heald and Cisco centrifugal pump driven by an oscillatinig engine by means of a belt. Steam was supplied by four plain cylinder boilers, each 36 inches diameter

Jan 1, 1879

By Peter J. Szabo

INTRODUCTION The time period from the detailed feasibility study to the post investment audity usually ranges from three to eight years depending upon the nature of the mining project considered. It is the only after the post investment audit that we know the adequacy of the assumptions made concerning operational risk assessment in the detailed feasibility or acquisition economics. The post investment audit results from numerous mining projects can best be described by a verse by John Greenleaf Whittier's Maaud Muller. It reads "For all sad words of tongue or pen the saddest are these 'It might have been!"' Dissecting the negative results of numerous mining projects we find faulty assumptions concerning markets, geology, capital investment and operational risk assessment. Although in hindsight many of these assumptions could have been considered impossible or impracticle to have forecast with any degree of certainty, we find that refined assumptions concerning operational risk assessment could have been made with only a modicum of additional "Due Diligence". Anyone who invests in a mining property should employ a much higher discount rate of future cash flow, (usually in the minimum range of 25%-30%), than he would expect from such safe investments as Treasury Bills or high grade Utility Bonds. The nature of this steep discount translates to a large uncertainty concerning the timing and actualization of assumptions contained in the detailed feasibility study. We must remember that when a project gets beyond 20 years, any contribution to the value of the project of cash flow is minimal due to the nature of the discounting process. Thus for each full or partial day lost in the development or early operation stage of a project, the financial impact will be greater than similar lost days later on in the project. Adequate operational risk assissment is particularly critical when bidding on competitive tenders for coal deposists in remote locations such as the Bowen Basin in Queensland, Australia. Because of the market attractiveness of these coal deposits for supplying end users in the Far East, Middle East and Europe, state governments require competitive tender biddings via the Authority to Prospect process. Front end bonuses and super royalty payments must be commited before the actual mining conditions are known. Time to submit firm offers from the actual request for proposal vary from 90 to 120 days. Thus any operational risk assessment must be detailed, realistic and reflective of the actual project. When one searches the literature, one finds limited qualitative data on operational risk assessment in valuation papers. Usually this facet of valuation takes a secondary role to such areas as reserves, markets, and environmental considerations. When one comes to the question of operational risk assessment more often than not one finds the use of "rules-of-thumb", such as tons per man shift, average production, average seam height, etc., are used to forecast results on which banks and other financial institutions are required to make investment decisions. Because of the extremely competitive environment of the 1970's and 1980's numerous financial institutions approved loans without adequate "Due Diligence", and are currently paying a steep price in terms of non performing loans and charge offs. One must always remember that each operation is unique with its own characteristic

Jan 1, 1985

By J. Jones-Parra

In previous Technical Notes, W. R. Rose' and W. Purcell have discussed the capillary pressure data presented by Welge.' Welge obtained capillary pressure curves of the imbibition type in which it was necessary to apply to the apparent wetting phase a greater pressure than that of the non-wetting phase to complete the cycle and reduce the non-wetting phase saturation to low values. Rose suggests in his Note that conditions of equilibrium could not have prevailed, since the. non-wetting phase pressure must always be the greater. Pur-cell in his Note, proceeds to postulate a pore system consisting. of a series of "holes in a doughnut," in which he contends that under equilibrium conditions it is necessary to resort to negative capillary pressures before significant wetting phase displacement can take place. There is a remarkable similarity between the shape of the capillary pressure curve calculated by Purcell and those measured by Welge. It is the purpose of this Note to show that, because Purcell neglected to account for the behavior of the residual wetting phase saturation, his system was not in equilibrium during imbibition; and, furthermore, that if his system had been in equilibrium, negative capillary pressures would not have been possible. In Purcell's pore system, the residual wetting phase will form pendular rings at the interstitial spaces existing somewhere within the system, for example, such as those spaces between "doughnuts" as shown in Fig. 1. The true capillary pressure is that across the pendular ring interface, and for the system to be in equilibrium the pressure drop across all interfaces must be the same, including that across the interface in the tight pores A of diaphragm B (Fig. 1). As the pressure across the cell is reduced, the advancing interface will move into the pore from the diaphragm, but at each pressure, the curvature of the pendular rings must be the same as that of the advancing interface if equilibrium is to prevail. Since equilibrium conditions are the basis for the entire argument, it follows that pendular rings must grow as wetting phase enters the pore, that is, as the pressure across the cell is lowered. In Purcell's calculated curve, the residual wetting phase saturation remains constant as the capillary pressure decreases. Thus, his curve does not represent an equilibrium process.

Jan 1, 1953

By Robert Forsyth

In working the Bessemer process, the bottom of the converter has always been a source of trouble and annoyance, and the subject of more experiments, probably, than any other part of the complex mechanism called a Bessemer plant. This will not appear remarkable when the duties this important piece of refractory material has to perform are taken into consideration. In the first place, by means of the tuyeres, it delivers at a high pressure the air necessary for the conversion of the bath of metal, and has then to resist the intense