Search Documents

By V. Steve Reed, Ed L. Reed

The in situ leach mining process generates a waste stream that is high in sulfates, total dissolved solids, and radium 226. During the mining phase, the volume of the waste stream is relatively low and consists primarily of the bleed stream. During the restoration phase, larger volumes of waste water are generated. These waste streams require environrnentally sound disposal. The low net evaporation rate in the Coastal Bend area precludes pond evaporation as a feasible disposal alternative. Reverse osmosis is a practical method of reducing the volume of the waste water handled, but the concentrated waste stream from the reverse osmosis unit must be disposed properly. Deep well injection into highly saline reservoirs is considered a sound method of disposing of the liquid waste generated by in situ mining in the Gulf Coast uranium district. Thirteen injection wells have been permitted to serve the disposal needs of the leach mining industry in Texas. Of these 13, 11 have actually been drilled. Seven applications are pending. The injection zones for the permitted wells range from depths of 3050 to 6200 feet. Pressure limitations imposed on these wells range from 500 psi to 1350 psi. The following criteria are used to determine the desirability of a disposal well site: 1. A minimal number of nearby, improperly plugged borings which penetrate the disposal zone; 2. Minimal crustal disturbance; 3. Sufficient salinity of the water contained in the disposal zone; 4. Protection of oil and gas producing zones; and 5. Sand of sufficient permeability and areal extent to handle the desired volume without fracturing the reservoir. 1. Improperly plugged borings: During the early part of the century, oil wells, gas wells and test holes were drilled using cable tool equipment, often with a minimum amount of surface casing. Production casing, when it was set, was often partly removed when the holes were abandoned. Thus, wells drilled prior to 1940 frequently have less than 100 feet of surface casing and either no production casing or the upper part of the production casing removed. Additionally, these holes are often plugged only with mud. The close proximity of these holes to an injection well location are a concern in that they can provide an avenue for injection-depth fluids to migrate up the bore hole and jeopardize shallower fresh water reservoirs. Usually, where there are more than 6 or 8 poorly plugged borings in a 2 1/2 mile radius of the well site, it is preferable to examine deeper zones for disposal well potential. The deeper zones are especially attractive where the borings are not in a cluster, which renders monitoring more difficult. Often, even the deeper disposal zones are penetrated by a few improperly plugged borings. When this condition arises, the potential for leakage through the borings can be addressed in the following ways. a. Demonstration that the static head in the boring is higher than the anticipated increase in bottom hole pressure generated at the boring by the disposal well. A 100 psi differential between these two pressures is recommended. The calculated increased pressure at a boring caused by injection should be refined using annual bottom hole pressure measurements in the disposal well. Figure 1 illustrates an injection pressure map which can be overlain on the oil well map to determine the anticipated increase in pressure expected at each oil, gas or abandoned hole. b. Shallow ground water monitoring. A shallow monitor well is drilled next to the boring and both pressure and quality measurements are made periodically in the shallow well. c. Disposal zone monitoring. Recently there has been a tendency for regulators to require disposal depth monitor wells instead of shallow well monitoring. We consider disposal depth monitoring to be a less effective method of monitoring because it provides only indirect evidence of potential problems. Assumptions have to be made for the unplugged borings, such as mud weight, that are not addressed by the disposal zone monitoring program. There is little improvement with this system to that discussed in "a" above. A shallow zone monitoring program, however, yields direct evidence of a developing problem with an unplugged boring. Leakage by the boring will be detected quickly by an abnormal increase in pressure in the shallow well. Quality monitoring will detect upward migration of poor quality fluids. The pressure data provide an early warning of impending leakage; the quality monitoring will detect actual fluid migration.

Jan 1, 1980

By C. J. McHargue

THE angles between the crystallographic planes in cubic crystals have been given by Bozorth,¹ in magnesium, zinc, and cadmium by Salkovitz,² and in tin by Nicholas. The determination of the orientation of single crystals and the study of plastic deformation require the knowledge of these angles and are often facilitated by use of a standard projection. Tables of these angles and standard projections have not been published for titanium or zirconium which have c/a ratios considerably less than those hexagonal metals for which this data is available. Accordingly, Table I has been prepared giving these angles. Fig. 1 presents a standard (0001) projection of titanium. The angle between (h1k1i1l1) and (h2k2i2l2) was calculated by means of the formula: h1h2 + K1K2 + 1/2 (h1k2 + h2k1 + cos 4 = [(hi2 + K + h1k1 + 3/4 l12 (h2² + C" a² 3/4 — l1 l2 C² k2²+ h2k2 + 3/4 —l2²) ] 1/2 c² The c/a ratio for titanium is taken from the data

Jan 1, 1953

By G. W. Mao, A. M. Gaudin, D. W. Fuerstenau

Activation of sphalerite with copper salts has long been thought of as a chemical reaction of the following form: ZnS + Cu++ [=] CuS + Zn++ [ 1 ] Early experimentation1-3 showed that the reaction seemed to be stopped by the coating of insoluble copper sulfide, but since the analytical methods were crude, it was only surmised that the reaction could proceed by diffusion. Probably the most conclusive evidence for reaction (Eq. 1) was obtained by Cooke,4 who found a stoichiometric replacement of Zn++ by Cu" after 50 days' reaction at about 100°C. Cooke also found the sphalerite to be covered with a rather thick coating of covellite, which in¬dicates that activation is a continuing replacement of Zn++ by Cu" rather than diffusion of Cu" throughout the sphalerite lattice. However, the occurrence of diffusion at high temperatures has been observed.5,6

Jan 4, 1959

W. B. PRICE,* Waterbury, Conn. (written discussion??.-It has been our experience, especially in cupro-nickel, that manganese has been very beneficial, not only, as stated by Mr. Braid, in removing sulfur, but also for its property of reducing oxides, thus making the metal more fluid, and enabling it to be poured at a lower temperature; this, in turn, prevents softening of the graphite pots and the absorption of carbon. It also acts very effectively in keeping the carbon in solution in the cupro-nickel, in the combined form. However, in the case of cupro-nickel, to obtain all these benefits it has been found necessary to keep the manganese content as near 0.25 per cent. as possible. Manganese also is very effective in diminishing the amount of blisters in cupro-nickel. So far as I am aware, both from personal experience and from the experience of others who have been engaged in the manufacture of nickel-silver and cupro-nickel, manganese used either in the form of pure metal or as manganese-copper alloy (30 Mn, 70 Cu) gives better results than any other flux. While this may seem a strong statement, manganese is the natural flux for nickel-silver and cupro-nickel.

Jan 12, 1918

By Nick Holonyak

Halogen vapor-transport synthesis of Ga(As,-,Px) and its preparation into laser junctions are described. Electrical and optical properties of Ga(As,-,PX) laser junctions are discussed. The present limitations in these properties are related to material proble?vzs and the very early state of development of Ga(As,-,PX), and are discussed in this context. Inhonzogeneity problems, fluctuation of As :P ratio, and problems with deep-level contaminants are described and related to Ga(As,-,PX) junction performance. Laser junctions are demonstrated which operate to wavelengths as short as 6470 A (77°K). The prospect that Ga(As,-,P,) will operate to wavelengths perhaps 100A shorter is mentioned. IN this paper we wish to describe some of the more important features of almost 1 year of experience in the preparation and properties of Ga(As,-,P,) p-n junction lasers. Because much data so far available are far from complete, some of the results still must be considered tentative and subject to correction and revision as work on Ga(As,-,P,) crystal problems progresses. Although the electrical, optical, and device properties of Ga(As,-,P,) junction lasers are understandably of considerable interest, the work to date points out that by far the most serious problems extant and those deserving first attention are problems involving the growth, doping, and perfection of Ga(As,-,P,) crystals. One of the most formidable of these is to grow Ga(As,-,P,) sufficiently free of deep levels, either due to contaminants or to structural imperfections, to allow fabrication of laser p-n junctions which can be cooled and not suffer from "freeze-out" of carriers on deep levels (and consequent double-injection behavior). In addition to the problems of growing crystals adequately free of deep levels and generally of the highest perfection, so that the best possible laser junctions can be realized, the further goal remains of increasing the phosphorus content well beyond 40 pct in an attempt to determine the practical lower wavelength limits of laser action in the Ga(As,-,P,) system. Even though the laser junctions prepared in Ga(As,-,P,) are of importance in their own right, we have considered them at this point mainly a means to study the growth and crystal problems of the material. It can be concluded that the laser junctions now available are almost completely limited by the purity and structural deficiencies of Ga(As,-,P,) crystals, and cannot be fairly compared with, for example, GaAs p-n junction lasers until Ga(As,-,P,) crystal growth has been more extensively developed. The basis for the statements above will become evident in the following sections which describe Ga(As,-,P,) crystal and junction preparation, and laser-junction properties. G(As,-,P,) CRYSTAL GROWTH As previously reported,2 we have found it convenient to employ the halogen vapor-transport process3 for synthesizing Ga(As,-,P,) crystals for use in laser junctions. Commercially available GaAs and Gap, separately prepared by halogen vapor tranport, are sealed in the desired ratio in a quartz vessel with a quantity of column-VI donor and a small quantity of metal halide which supplies the halogen for transport. The sealed ampoule, as shown in Fig. 1, is heated at a temperature in the range from 1025" to 1100°C at the position of the source GaAs and Gap. The GaAs and Gap are simultaneously vapor-transported and deposited as Ga(As,-,P,) at one end of the ampoule

Jan 1, 1964

By F. Cadena, Fred C. Bond, Walter L. Maxon

Grinding is one of the major problems in present-day milling practice, and in many cases, it represents one of the main items of expense. It becomes necessary from time to time, to compare grinding practice in one plant with that in another plant, and in making such comparisons, it would be very desirable were there available accepted standards of grinding resistance for the materials involved. Such a set of grinding constants would also be of considerable value in planning new grinding installations. There have been some tests published, notably those of Lennox,' which have been generally cited as a basis for such comparisons. Most of the tests made have been based upon open-circuit grinding, in which a weighed sample of the ore was crushed to pass a certain mesh, and was then ground under certain conditions, either wet or dry. Grinding was continued until a certain desired fineness was attained, and the comparisons based on the grinding time, or the samples were all ground for a certain specified length of time and comparison based upon the screen analysis of the products. Such methods have been acceptable where the ore was to be ground in open circuit. However, in modern milling practice, many grinding problems involve closed circuits wherein the oversize returns to the mill and a large circulating load builds up. A method of testing that does not take the circulating load into consideration might yield results quite different from those to be expected in practice, because the minerals in the ore that offer maximum resistance to grinding will accumulate in the circulating load up to an equilibrium value. Thus the nature of the ore charge in the mill at any instant may differ greatly from that of the new feed, with a consequent error in the rate of grinding determined by such a method. For example, let it be assumed that an ore to be tested consists of equal parts of difficult grinding mineral and easy grinding mineral. This is to be compared with an ore used as a standard, and consisting of minerals which are all of about the same grindability. If a comparison

Jan 1, 1935

By P. Ramachandrarao, T. R. Anantharaman

CONSIDERABLE interest has lately been evinced as regards the nature of chill zones in solidified metals and alloys. Biloni and Chalmersl were the first to show through their study of segregation substructures in some nonferrous alloys that the formation of the dendritic region may be preceded by a diffusionless solidification process, viz., predendritic solidification. Subsequently Bower and Flemings2 tried a special solidification technique wherein the liquid was drawn into a narrow copper mold with polished surfaces and concluded that convection might trigger some multiplication mechanism leading to grain refinement. Using uncoated and partially coated surfaces for molds in the Bower-Flemings technique as well as in conventional molds, Biloni and Morando3 have very recently brought out the importance of the rate of heat extraction on the mechanism of solidification. We report here on the surface structures and substructures observed in a Sn-1 wt pct Pb alloy solidified at even higher cooling rates (riz., l05 to l07 ºc per sec) than those employed by earlier workers. The alloy was made by melting tin (99.99+ pct) and lead (99.9+ pct) in a silica tube under vacuum. Small quantities of the homogenized alloy (0.5 to 1.0 g) were then quenched (or splat-cooled) from the melt by the "gun technique" developed by Duwez et al.4 The thickness of the resultant foils varied from specimen to

Jan 1, 1970

The figures given here were received through the courtesy of the Bataafsche Petroleum Maatschappij and the Standard-Vacuum. There is an increase in production for the year of approximately 4½ million barrels. In November the average production indicated that during the year 1935 the total production would probably exceed 50 rnillion barrels. To maintain this production, only 106 wells were drilled during the year, mainly in South Sumatra.

Jan 1, 1935

By Thomas E. Bruner

With drilling costs playing a pivotal role in the economics of most mineral exploration programs, there has been a significant effort over the past decade to trim expenditures in this area. One result of these cost-cutting measures has been the substantial shift to use of rotary drills. By the mid-1970's, rotary drilling accounted for six times as much footage as core drilling in exploration work. Among the various rotary drilling techniques, the use of dual-tube drilling for continuous sampling is attracting growing interest. Factors such as drilling speed and cost advantages, coupled with favorable comparisons between chip samples and solid core samples, have helped to spark this interest.

Jan 4, 1979

By John M. Pitt

Shear strength assessment and the associated variability in rock masses historically have been hindered by high costs and biases in laboratory testing programs. An in situ direct shear device was developed on the principle of the previous borehole shear device for soils. Using wedge action to simultaneously apply normal and shear stress to an envelope of material on the periphery of a borehole, the device develops a complete Mohr-Coulomb failure envelope. Tests performed in homogeneous materials show expected strengths and their variability equivalent to laboratory tests. However, tests in a structurally non- homogeneous coal did not display significant variability. A 38 mm diam borehole was used in this work; however, larger or smaller bore- holes may also be used within the size limits of the device. The device is employed in holes commonly drilled for rock bolt placement, at 1 to 2 minutes per test.

Jan 1, 1984

By C. T. Wei, A. Kelly

USING a recently developed X-ray method, reported by Schulz,2 it is possible to make a rapid survey of the perfection of a single crystal at a particular surface. This technique has the advantage of allowing a large surface of a specimen to be examined by taking a single photograph and it compares well with other X-ray methods in regard to sensitivity of detection of small angle boundaries. During the course of a survey of the perfection of large crystals of aluminum produced by a number of methods, an examination has been made of a number of single crystals produced from the melt using a soft mold (levigated alumina)." Crystals grown by this method are known, from an X-ray study carried out by Noggle and Koehler,3 to contain regions where they are highly perfect. In the present work, it has been possible to obtain photographs showing directly the distribution of low angle boundaries at a particular surface of these crystals. single crystals were grown from the melt using the modified Bridgman method with a speed of furnace travel of -1 mm per min. These were about 1/10 in. thick, 1 in. wide, and several inches long. The metal was 99.99 pct pure aluminum supplied by the Aluminum co. of America. The crystals were examined by placing them at an angle of about 25° to the X-ray beam issuing from a fine focus X-ray tube of the type described by Ehrenberg and Spear4 and constructed by A. Kelly at the University of Illinois. A photographic film was placed SO as to record the X-ray reflection from the lattice planes most nearly parallel to the crystal surface. The size of the focal spot on the X-ray tube was between 25 and 40 u, and the distance from the X-ray tube focus to the specimen (approximately equal to the specimen to film distance) was -15 cm. White X-radiation was used from a tungsten target with not more than 35 kv in order to reduce the penetration of the X-rays into the specimen. Exposure times were approximately 1 hr with tube currents between 150 and 250 microamp. The type of photograph obtained from these crystals is illustrated in Fig. 1, which shows a number of overlapping reflections from the same crystal. The large uniform central reflection is traversed by sets of horizontal white and dark lines. These two sets run mainly parallel to one another. Lines of one color are wavy in nature and often branch and run together. Large areas of the crystal surface show no evidence of these lines whatsoever. The lines are interpreted as being due to low angle boundaries in the crystal, separating regions which are tilted with respect to one another. A white line is formed when the relative tilt forms a ridge at the interface and a black line is found when a valley is formed. In a number of cases, the lines stop and start within the area of the reflection and often run into the reflection from the edge, corresponding to a low angle boundary starting from the edge of the crystal. The prominent lines run roughly parallel to the direction of growth of the crystal although narrow bands can run in a direction perpendicular to this; see Fig. 2. Although they may change their appearance slightly, the lines tend to occur in the slightly,Same place in the X-ray image and to maintain their rough parallelism when the crystals are reduced in thickness by etching. Thus the low angle boundaries can occur at any depth within the crystal. The appearance of the lines is unaffected by subjecting the crystal to rapid temperature changes, such as plunging into liquid nitrogen or rapid quenching from 620°C. From the width of the lines on the x-ray reflection, values can be found for the angular misorienta-tion of the two parts of the crystal on either side of a boundary. The values found run from 1' to 10' of arc, but values of UP to 20' have sometimes been found, e.g., the widest lines on Fig. 2. These mis-orientations are much less than those commonly found in crystals possessing a lineage structure. When a number of a and white lines occur, running in a roughly parallel direction across the image of a Crystal, the total misorientation corresponding to lines of one color is approximately equal to that corresponding to lines of the other color. The interpretation of the lines as due to low angle boundaries has been checked in a number of ways. Photographs taken with different specimen-to-film distances distinguish lines due to low angle boundaries from effects due to surface relief of the specimen. Normal Laue back-reflection photographs, taken with the beam irradiating an area of the surface showing a number of the lines, show white lines running through each Laue spot. Black lines are set to see by this method. X-ray photographs were also taken, using the set-up described by Lam-one et al.5 when the beam straddles regions giving rise to lines in the Schulz pattern, split reflections are observed within the Bragg spot. The misorienta-tions calculated from the separation of these reflections and that found from the widths of the lines on the schulz technique patterns show good agreement. An exposure was made with Lambot technique of an area of the crystal showing no evidence of low angle

Jan 1, 1956

By AIME AIME

AT the meeting of the Iron and Steel Division at Cleveland, Sept. 10-12, the morning of Thursday, Sept. 12, has been set aside for an excursion to visit the ore docks, blast furnaces, and steel plants. A special train, made available through the courtesy of Appleton Cleveland, general superintendent of the Pennsylvania Railroad, will leave the siding near the Auditorium at 8.35 a. m. The trip will be free, but tickets must be' obtained in advance at the booths for registration for excursions at the Auditorium. An hour will be spent at the docks, an hour at the Central blast furnaces, and two hours at the Cuyahoga works of the American Steel and Wire Co. A buffet luncheon will be served, with the compliments of the Pennsylvania Railroad Co., on board the train en route. At the Tuesday morning session, Sept. 10, a motion picture showing the operations in making wrought iron by the Aston process will be shown for the first time.

Jan 1, 1929

By E. R. Morgan, J. C. Shyne, V. F. Zackay

NITROGEN used as an alloying element in steel has received increased attention in recent years. Its merit as an austenite stabilizer and hot strengthener has long been recojinized, particularly by European investigators.' Recent work' indicates that nitrogen contents of 1/2 pet or more allow the addition of several percent of ferrite-forming hot strengtheners, such as molybdenum, without subsequent austenite decomposition at elevated temperatures. The room temperature properties of such alloys are characterized by high yield and tensile strengths with excellent ductility, even after cold working, as shown in Tables I and 11. The 1350°F creep-rupture properties of Cr-Mn-Mo-N steels are comparable to those of commercial alloys such as Timken's 16-25-6, containing 16 pct Cr, 25 pct Ni, and 6 pct Mo, as shown in Table 111. Cr-Mn steel containing 1/2 pet N must be made under pressure if ingot gassing is to be avoided. However, there are difficulties attendant to this practice. Pressure melting restricts the ingot size, and the equipment required is costlier and more complicated than comparable air melting facilities. An effort was made, therefore, to determine more economical methods of adding nitrogen. The pressures generated in centrifugal casting usually range from 5 to 10 atm and are sufficient to prevent the gassing of high nitrogen Cr-Mn steels. A centrifugal casting was made of an alloy containing 16 pct Cr, 18 pct Mn, 2 pct Mo, and 0.73 pct N. A risk, 8 in. diam and 11/2 in. thick, was cast at 1000 rpm. It has been calculated that a pressure of 9 atm was developed at the periphery of the disk at this speed. Metallographic inspection of specimens taken from the disk revealed no gas holes or other defects. The elevated temperature properties of radial and circumferential specimens taken from this casting are given in Table IV. The creep-rupture life of this cast nickel-free austenitic steel was equivalent to that of the wrought Cr-Mn-Mo-N steels. Although centrifugal casting appears to lend itself to the manufacture of high nitrogen austenitic steels, its applicability is limited to relatively small sizes. A process applicable to the production of large ingots of high nitrogen steels is suggested by low carbon rimming steel practice. Gas holes formed during ingot solidification are not detrimental so long as they weld shut during hot rolling. An economic advantage of gassing ingots is the increased ingot-to-slab yield, especially if the ingots are mechanically capped. Also, it is probable that higher nitrogen levels can be achieved with mechanically capped ingots than with hot-topped ingots. A series of gassy heats was made under both atmospheric and higher pressures, as indicated in Table V. Several of the air melted ingots were mechanically capped by chilling the molten ingot tops with a steel plate. The ingots were allowed to freeze in steel molds without hot-tops unless otherwise indicated. A comparison of Table 111 with Table V shows no significant difference in the creep-rupture properties of the gassy and the nongassy ingots after hot work- ing nor between the gassy ingots produced under different conditions. References 1 F. Rapatz: Application of Stainless and Heat Resisting Steels Alloyed with Nitrogen. Sinhl and Eisen ( 1941) 61, pp. 1073-1078. 'V. I?. Zackay, J. F. Carlson, and P. L. Jackson: High Nitrogen Austenltlc Cr-Mn Steels. Trans. ASM 119551 48, PP. 509-523.

Jan 1, 1957

By AIME AIME

CLYDE WILLIAMS, after graduating from the University of Utah as a chemical engineer, worked for a time in western mills and smelters. He then joined the U. S. Bureau of Mines and during the World War studied Ordnance Department and Navy problems on ferroalloys and alloy steels at the Cornell University laboratories. Later, as superintendent of the Northwest Experiment Station of the Bureau, he was active in electric furnace and ore reduction work. Clyde then went to South America and surveyed the iron and fuel resources of the Argentine. Returning, he became chief metallurgist of the Columbia Steel Corp., of

Jan 1, 1936

By G. Herget, O. Garg

Trends will continue towards more automated, and sometimes larger mining and haulage equipment to reduce pit development and haulage costs. To save labour costs, larger capitalization of open pits is required and pit design and stripping ratios have to be firmed up at a very early stage of mine planning. Bench failures will assume a greater importance with larger equipment and at present we have only a limited capability of predicting stable slopes in complex structural geological settings. Deep open pits will pose particular problems in regard to high toe and floor stresses. This will require the development of more efficient systems for rock mass exploration and an improvement of our predictive capability in regard to pit slope stability and appropriate management of ground- water and materials. To meet the challenge, we have to improve: a) Analytical tools to assess slope stability in structurally complex settings as found in large open pits; b) Core orientation methods during diamond drilling operations; c) Geophysical logging methods to obtain geotechnical and structural geological information for large volumes of rock; and d) Geotechnical data handling systems to define mechanical properties

Jan 1, 1983

By J. Y. Oldshue

INTRODUCTION The field of fluid mixing involves many different kinds of process objectives. In order to classify these objectives, Table 1 gives a listing of five basic application categories, gas-liquid, liquid-solid, liquid-liquid, miscible liquids, and fluid motion. However, each of these areas can be broken up into two different concepts one involved with uniformity of solids or liquids as a criteria, and the other involved with chemical reactions or mass transfer. The things that we would do to design a fluid mixing for solid suspension are quite different from things that we would do to design a mixer for heat transfer or gas-liquid mass transfer. Therefore, there are really ten separate mixing technologies. Each of these areas has its [ ] own principles of fluid mechanics, scale-up techniques and application experience. We will take a look at each of these areas and look at some of the ways that we can handle fluid mixing applications which.

Jan 1, 1979

"It shall be within the discretion of the Board of Directors to establish a medal to be known as the Charles F. Rand Memorial Medal to be awarded at such a time 'and under such rules as may be determined by the Board of Directors, for Distinguished Achievement in Mining Administration." The establishment of this medal was announced at the annual meeting in February, 1932, the term "mining" being defined in its broad sense to include metallurgy and petroleum. The members of the Charles F. Rand Foundation Award Committee, of which J. V. W. Reynders is Chairman, are listed on page 12. In both 1938 and 1939, the Committee gave consideration to the question of choosing a medalist but in each year the decision was reached to give financial help to other projects as an alternative. In 1938, publication of a monograph on "Struc¬ture of Ore Deposits in the Continen¬tal Framework" and of a booklet en¬titled "The Call for Endowment" was financed; and in 1939, a special appro¬priation was made to defray the ex¬ penses of special speakers for Affiliated Student Societies of the Institute. In 1940, the Committee elected to nominate a candidate for the medal and unanimously selected Robert, Crooks Stanley, Chairman of the Board of the International Nickel Co. This recom¬mendation was approved by the Board of Directors and Mr. Stanley became the first recipient of the medal. Citation for Award to Robert Crook,, Stanley. "For His Pioneering Leadership During a Period of Active Growth and Development of a World-wide Enterprise Involving the Mining of Nickel Ores, the Metallurgical Treatment Thereof, and the Expansion and Diversification of World Markets for Nickel Products. "For His- Able Direction of the Corporation Encompassing These Activities, Which Has Established an Enviable Record in Its Relations With Employees. Stockholders and With the Public."

Jan 1, 1941

By R. P. Dolan, W. M. Shedd, B. L. Buchanan

Analytical expressions are derived from empirical data relating the basic physical device parameters to the radiation dose. To put in perspective and justify the approach taken, the overall problem and methods of attempted solution of radiation damage to transistors in a missile or satellite environment is briefly examined. The main emphasis is on a new criteria for neutron radiation hardness and the device design implications resulting from using this criteria. Contrary to other derived criteria, the derived bipolar hardness relation depends mainly on the initial lifetime rather than the base transit time. It is shown, that contrary to previously accepted beliefs, the inherent attainable radiation tolerance of JFET's is at least a factor of ten greater than the radiation tolerance ofbipolars. Experimental results on JFET's designed for maximum neutron radiation tolerance are presented. The accuracy, utility, and range of possible validity of various published lifetime and carrier removal damage constants are discussed. It is well known that transistors are subject to damage due to radiation at much lower radiation levels than those which would cause structural damage to a missile or satellite. The three principal categories of radiation damage to transistors are displacement, ionization, and thermomechanical. The main cause of displacement damage is fast neutrons, and the main effects which permanently degrade transistor operation are minority carrier lifetime reduction and carrier removal. A second-order effect is mobility reduction. The main cause of ionization damage is gamma radiation which results in permanent effects due to charge build-up in the oxide and transient effects due to photo-current generation. The transient effects are usually handled by using circumvention techniques in the electronics system. The extent of the transistor degradation due to displacement and ionization damage depends strongly on the transistor type, whereas the extent of thermomechanical damage does not depend on the transistor type, but depends mainly on packaging and metallization which are common to all transistor types. The standard transistor types are categorized in Fig. 1 and typical cross-sections are shown in Fig. 2. The original reason for the designation of the two classes of transistors was that the unipolar operation depends on only one carrier (majority) and the bipolar operation depends on both minority and majority car- riers. The bipolar is then seriously degraded by minority carrier lifetime reduction, whereas the unipolar or field effect transistor is not. One of the two principle classes of field effect transistors, the junction field effect transistor (JFET), depends strongly on carrier removal. However, the insulated gate (MIS) is little affected by either carrier removal or lifetime changes, but is virtually eliminated as a radiation resistant device because of permanent charge build-up in the insulator caused by ionizing radiation. The bipolar and JFET suffer only minor effects due to charge build-up in the oxide passivation when compared1 to the MOS. This is because the active region of the MOS is adjacent to or part of the oxide layer. It is then the bipolar and JFET which are potentially resistant to permanent radiation damage. DERIVATION OF RADIATION TOLERANCE RELATIONS Criteria. The bipolar is by far the most widely used transistor type. The usual criteria for hardening bipo-

Jan 1, 1970

By Jr. W. L . Phillips

The deformation and fracture characteristics of lithium-fluoride single crystals stressed in compression at room temperature have been studied. In as-cleaved specimens the stress-strain curves were variable; two types of {110} fractures were observed in the vicinity of kink bands. The stress-strain curves of annealed crystals were reproducible; {100} cracks formed which propagated along the (100) and (110) planes. The deformation and fracture characteristics were affected by quenching and X-ray irradiation. STUDY of the mechanical behavior of nonmetallic materials has received considerable impetus in recent years because of the need to overcome the problem of brittleness before the refractory properties of nonmetallics can be fully exploited. Ionic crystals provide a convenient and simplified starting point from which to study the deformation and fracture processes in nonmetallic materials. Early investigations of the mechanical behavior of non-metals were restricted largely to determinations of the crystallographic indices of the cleavage and fracture planes and the glide and twinning elements. Until recently, only occasional systematic studies of the deformation characteristics of non-metals have been made; and investigations of the forces necessary to initiate plastic deformation and the factors which affect the flow characteristics have been restricted largely to studies of sodium chloride'-7 , magnesium oxides-l3 and lithium fluoride. 14-22 Fracture studies on alkali halide and metal oxide single crystals have been limited despite the fact that these materials have a number of advantages for fracture studies. Because they are transparent, the cracks which form can be viewed in three dimensions instead of in two dimensions as in metals. Also, they exhibit stress birefringence under polarized illumination, which enables the internal stress pattern and, therefore, the distribution of dislocations to be examined in the vicinity of the fracture. Early workers1-4 have shown that ionic crystals with a cubic structure fracture in tension along the (100) plane normal to the applied stress. These fractures were brittle at room temperature and propagated very rapidly across the cross section of the crystal. More recently, Stokes, Johnston, and Lil0 have studied crack formation in compressed magnesium-oxide single crystals. They found that the cracks, which were observed after about 3 pct strain, formed in the region of a kink band and lay on conjugate (110) slip planes instead of the usual(100) cleavage plane. Two different types of cracks were noted: stroh23 and secondary. The Stroh cracks did not exist merely on the surface but extended through the specimen in the form of tiny slits. A secondary

Jan 1, 1962

By A. G. H. Anderson, Eric R. Jette

During the period from 1910 to 1920, there was a lively interest in the subject of grain growth and many papers were published, followed by interesting discussions. Questions dealing with the fundamentals of grain growth—why and how it occurs—were treated in papers by Howe,' .Jeffries,² Sauveur,² Chappell,4 Beilby,5 Mathewson and Phillips,6 Mc Adam,7 Carpenter and Elam,8 Stead and Carpenter,9 Ruder,l0 as well as others. Since that decade, much indeed has been done regarding the practical control of grain size, and it is now possible to order material having a size sperified in the American Society for Testing Materials classification. Also, one hears the term "spliced boundaries" used in connection with certain tungsten lamp filamentsl1 wherein it is important to prevent "sagging" between consecutive turns of the helix.12 This practical use of a certain knowledge as to the things that influence or even control grain growth should not be taken as an indication that the subject has been thoroughly explored and that nothing more can be learned from fundamental studies. It is with this thought in mind that a report of some observations and experiments on abnormal grain growth is believed justified. Abnormal grain growth is met with in heat-treating high-carbon steels in the austenitic range,'? in the hardening treatments of high-speed steels,14'15 and in the low-temperature annealing of strained low-carbon steels as in sheet and wire material. Entirely aside from these instances of exaggerated grain growth, which some might consider as freakish, it is thought that abnormal growth is simply a case where the growth forces and the forces tending to prevent growth are almost, but not quite, evenly balanced. Information relative to grain-growth characteristics in general may be obtained from a study of abnormal growth conditions, which may be looked upon as vantage points. Reflection will show at once that if growth forces are great in comparison to inertia or resistance to growth, many crystals start to grow and, for that reason, none becomes very large, whereas if inertia is

Jan 1, 1938