Search Documents

By Charles Eichrodt

THE ore that is being treated by the present plant lies between the leached zone, or capping, and the mixed sulfide and oxide zone. The principal copper minerals are chalcanthite (CuSO4.5H20), brochantite (CuS04 3Cu (OH)2) and atacarnite, (CuC12.3Cu (OH)2). There are, in addition, some other minerals such as cuprite and kröhnkite (CuSO4. Na2SO4.2H20). These minerals, with many others, occur in a greatly crushed granodiorite rock. Most of the copper-bearing minerals occur in the cracks and veinlets, but there are disseminated values and it is probably the relative proportion of these that accounts for some otherwise unexplainable variations in extraction. The entire mineralization of the ore is complex and varies with depth. This variation, the problems presented thereby, and the effect of various constituents of the ore will be taken up in detail. An analysis of an unweighted composite of the ore treated during 1927 follows:

Jan 1, 1930

By Henry E. Wood

In my opinion, the concentration of minerals by flotation is the most interesting problem in ore-dressing, and will command eventually far more consideration than it has at present. For many ores it furnishes a complete method of concentration absolutely independent of specific gravity, and thus simplifies the milling of many difficult combinations. Not having to recognize the influence of specific gravity, we are also able to dispense with some of the complications resulting from classifying-conditions. Where flotation cannot be used for a complete separation of the minerals from the gangue, it will be found, in nearly all cases, to save those portions which are generally lost by reason of their fine state of division. For this reason, it should be looked upon mainly as an aid to general concentration, although there are many ores so well adapted to flotation that more than 90 per cent. of the valuable metals can be recovered from them in one operation by this process. In presenting the results of my investigations in flotation, I have endeavored to theorize as little as possible. That side of the subject has been extensively discussed by others. My earliest work with flotation was done in 1895, when I used various oils, grease, soap, etc., with results that were remarkable. I did not realize then that with water alone equally good separations could be made. Up to 1906, my endeavors were confined to attempts to keep the concentrates on the tables well wetted and away from exposure to the air. In common with others, I observed that when there mas any obstruction in the wash-water on the table of sufficient size to divert the water to either side, the concentrates collected, and, on exposure to the air, would promptly float away. This convinced me that the sulphides were all good "swimmers," and that if,

Jan 1, 1913

In the January Bulletin a list was published of Societies' publications, magazines, etc., which were duplicates and were discarded at the time of-the consolidation of the libraries of the three Founder Societies. A second list published herewith includes text books which are duplicates and which will be disposed of about April 1, 1916, by the Board of Directors of the Institute through the, Library Committee.. If, meanwhile, members desire to secure some of these books, they are asked to communicate at once with the Secretary as. this is an unusual opportunity to secure books at an extremely low price. Airy, George Biddell.-Magnetism, London, 1870, Bd. Alberti, Friedrich von.-Halurgische geologic. Erster Band. Zweiter Band. Stuttgart, 1852, Bd. American Iron and Steel Association.-Ann. Rep. of the Sec'y. Statistics of American and, Foreign Iron Trades, 1877. Phila., 1877, Bd. Same, for year 1878. Phila., 1879, Bd. American. Telephone and Telegraph Co.-Ann. Rep. of Directors to Stockholders, 1911. N. Y., 1912, paper. Armagnat, H.-Induction Coils. Trans. by Otis Allen Kenyon, N. Y., 1908, Bd. Armstrong Cork Co. Insulation Dept. Nonpareil Corkboard Insulation. Pittsburgh, 1909, Bd. Associazione fra gli Industriali Metallurgici Italian.-The Metallurgic industry of Italy. Description of some of the principal works. Milan, 1911, Bd.

Jan 2, 1916

By W. J. Helfrich, C. L. Sollenberger

Many present direct reduction processes utilize iron ore concentrates for the production of sponge iron and the sponge iron is usually preferred as an agglomerate. Pelletizing a high grade iron oxide concentrate prior to reduction is a simple approach to the high capacity production of a uniform and agglomerated sponge iron product. The present paper describes the effect of different atmospheres and physical characteristics on the reduction of pelletized iron oxide concentrates. The kinetics of iron oxide reduction have been I studied by numerous investigators1-4 and a rate equation for the hydrogen reduction of hematite and magnetite has been proposed. Mc Kewan' obtained kinetic data for the reduction of hematite spheres sintered at 13'70°C (2498'F'). The kinetics of magnetite reduction was studied by Quets. He compacted the oxide at a pressure of 1 ton per sq cm and sintered the specimens to densities of 95 to 96 pct of theoretical. These studies demonstrated that the reduction of iron oxide is a topochemical process and that the rate of reduction is proportional to the receding surface area of remaining iron oxide. Thus, the measurement of the kinetics of iron oxide reduction depends upon the development of a measurable and well defined interface between metal and reacting oxide. It is evident that the reduction rate will be constant only when the rate of formation of the reaction product layer is constant. It was recognized by Joseph' and Edstrom' that the physical character of the oxide will determine the configuration of the interface between oxide and metal. The reduction of oxides which exhibit few pores or no interconnected pores should proceed by topochemical processes. However, if a massive or dense crystalline ore cracks during the reduction of the oxide, thus allowing the reduction to Proceed away from a well defined oxide/metal interface, then the observed reduction rate will vary or change during reduction. From a process standpoint, it would be difficult to apply absolute reduction rates determined for crystalline or nonporous iron oxide to the direct reduction of a porous pellet of iron ore concentrate. Most present direct reduction processes are attempts to utilize iron ore concentraates in the production of sponge iron. The sponge iron is usually preferred in an agglomerated form for subsequent melting practices. Pelletizing a high grade iron oxide concentrate prior to reduction is a simple approach to the high capacity production of a uniform and agglomerated sponge iron product. One process for preparing such a product has already been de-scribed. This paper describes the effect of different atmospheres and physical characteristics on the reduction of pelletized iron oxide concentrates. ORE CONCENTRATES STUDIED A magnetite concentrate from Reserve Mining Co. and a hematite concentrate from U.S. Steel Corp. were used in preparing pellets for these experiments. A head analysis of these concentrates is given in Table I. To compare the reduction rates of pelletized concentrates, it was necessary that each pellet contain equal amounts of oxygen which could be removed by reduction, regardless of the oxidation state, i.e., Fez% or Fe304. Also, because of the difficulty in preparing spherical pellets of uniform size, weight, density, and porosity for experimental purposes, pellets of a cylindrical shape were formed in a press.

Jan 1, 1961

By Gram Curtis

The apparatus described below for the handling of plates upon their delivery from the rolls, embodies features believed to be of interest to those contemplating the building of new plate-mills, and also to such owners of existing mills as may be considering the improvement of their works. The points to which attention is called are the small space required for the finishing-end of the mill, and consequently the very moderate size of the building for the amount of plates handled; the directness and ease of manipulation, and therefore the mall amount of labor required; the distribution of plates; the facilities and time allowed for their cooling. These, together with other features of detail and general arrangement scarcely less important, will become apparent when the descriptions and illustrations herewith given are understood. As these devices deal with the finishing of the plates only, they may be added to any plate-train when the floor-space and the building are large enough to permit their introduction; and it will be obvious that the features of this method, more or less modified, are applicable to any existing mill. Figs. 1 and 2 show a three-high 32-and 19- by 120-inch Lauth mill, with hydraulic lifting-tables, served by four heating-furnaces, with hydraulic cranes for charging and drawing. Upon leaving the rolls, the plate is allowed to rest with its forward edge projecting somewhat beyond the end of the catcher's table. Here it is seized by the automatic tongs, A, suspended from a buggy travelling in the overhead trough, B, and actuated by the hydraulic cylinder, C. These tongs are operated by a boy, who stands several feet from the heated plate, and controls the long light handle, D, shown in the plan, Fig. I. His duty is merely to advance the tongs by means of .the hydrulic cylinder, C, to raise or

Jan 1, 1892

By A. L. Holley

THERE is a growing demand for pure and cheap material for fine open-hearth steel ; a material not only very free from phosphorus, but from carbon and silicon; so that it may he rapidly converted into steel. Iron and steel scrap are not trustworthy as to quality, and they are often dear. There are three methods of purifying cheap materials for the open hearth. 1. Mechanical puddling, as done at Creusot, which removes 90' per cent. of the phosphorus from the pig iron. 2. Krupp's washing process (the conduct and results of which I fully described in a former paper*), which eliminates 70 to 80 per cent. of the phosphorus and most of the sulphur and silicon from pig iron. Neither of these processes would sufficiently purify, for very fine steel, those very impure pigs which are cheapest in many parts of the United States: 3. The process of producing directly from the ore an iron which is practically pure chemically, although mechanically mixed with the impurities of the ore. This is the oldest of iron processes ; one form of it, the Catalan forge, employed to produce charcoal blooms, is still in use, but its great cost is rapidly throwing it out of competition. Among the modern attempts to produce iron direct from the one, on a large scale and at a cheap rate, several have been in various respects successful. Dr. Siemens's process of treating a ton and a half or more of ore and the coal to deoxidize it, in a rotating gas furnace, and bringing out, in some four hours, a ball of chemically pure iron so soft that the fluid and impure slag may be squeezed out of it, is the most attractive and the most highly developed of all the modern direct processes. I have watched it, from time to time, since 1874, and have noted a steady improvement. It may now be said to have passed the experimental stage, although, like older processes, it must be adapted by practice to special materials. The cause which has been more potent than all others, including the defects of the best direct processes, to bring these processes into disrepute, is the waste-ful treatment of the direct product. With one or two exceptions (when failure was due to other and obvious causes), the direct product has been made into wrought iron (weld iron). Even Dr. Siemens has, at Towcester, in England, and at Park, Bro. & Co.'s, in Pittsburg, set up his apparatus for this purpose. Is it likely that

Jan 1, 1880

By H. W. Graham

THE young metallurgist of today who thinks casually of the technical literature of the steel industry might conclude that little has been published concerning the Bessemer process. This conclusion is true as relating to the last decade or two, but there is a fairly voluminous Bessemer literature in the period of 1860 to 1910, Since that time, however, an entirely new level of metal-lurgical knowledge of steelmaking has been reached; and the present paper is simply an effort to look broadly from this new level and to bring the recorded history of the process up to date, It is an effort to appraise the acid Bessemer method of steelmaking in the light of today's technical knowledge thereof. In this paper matters of history will be dealt with only insofar as they contribute to an understanding of today's situation. Attention will be directed to the apparent causes of past developments in seeking to perceive the true direction of trends now in existence and effective as bearing upon future developments. The paper will discuss the economics of the Bessemer process, but only to the extent that will bear upon the metallurgist's understanding of his respon-sibility. The problem of the quality of Bes-semer steel will be reviewed and examples will be given of the technical data upon which the reasoning of the paper is based, Matters of engineering design, mechanical maintenance, operation and metallurgical investigation will be surveyed. Compari-sons will be made between the Bessemer and open-hearth processes for the sake of clear and ready understanding,

Jan 1, 1940

By Arthur Taggart

INTRODUCTION THE flotation process for the concentration of ores is a method by means of which one or more of the minerals in the ore (usually the valuable ones) are picked up by means of a liquid film and floated at the surface of .a mass of fluid pulp. Here they are separated from the other minerals, which remain immersed in the body of the pulp. In general, the minerals which are floated are sulphides of metallic luster, but some other minerals of metallic luster such as graphite and some sulphides with adamantine luster, such as sphalerite and cinnabar, are amenable to treatment by the process. The importance of flotation lie's in the fact that it is primarily a "slimes process" by means of which the particles of valuable mineral, too fine for efficient gravity concentration, are saved with a high percentage of recovery. Recoveries in the mills treating low-grade copper sulphide ores have been advanced 10 to 20 per cent. by the installation of the process and similar increased savings have been accomplished by the same means in mills treating sulphide ores of zinc and lead. When finely ground ore containing sulphides mixed with a siliceous or earthy gangue is brought gently onto the surface of a body of water, in a direction forming an acute angle with the surface of the water, a considerable portion of the sulphide constituent of the ore floats on the surface of the liquid, while the gangue sinks. This is the so-called film flotation, exemplified by the Wood and Macquisten processes. When gas bubbles are introduced into a fluid pulp composed of finely ground ore and water, to which has been added (1) a small amount of certain oils, or (2) a small amount of certain acids or acid salts, or (3) a small amount of certain alkalis or alkaline salts, or (4) a small amount of a mixture of oil with acid or alkali, the sulphide particles in the ore are brought to the surface on the gas bubbles. These collect in a froth

Jan 8, 1916

By R. B. Fuller, E. T. Casler

MANY changes were made in the methods and equipment used in the mining of pebble phosphate rock in the generation immediately preceding the present World War and it would be extremely interesting to note the improvements that will be made during the next generation. Literally, much water has gone over the dam since the days when we used local cordwood for generating steam and drying pebble phosphate rock. belt-driven centrifugal pumps operated by steam engines. and floating dipper or centrifugal dredges; when we removed overburden by small steam shovels and transported it by dinkey locomotives and six-yard cars; when washing machinery was installed on wooden structures the washers being replaced every four to six years. Those were the days when men were plentiful, and 47 different mining companies were selling their products, based on .decidedly meager information; and. like so many mining operations, little thought was given to conservation. As the importance of phosphate rock has become more prominent in the thoughts of our economists, a more intelligent approach has been made to mining problems. Vast improvements have been made in the technique and processing of the phosphate matrix and stripping of overburden, which, in turn, have brought developments in machines and equipment and a more

Jan 1, 1944

HIGH-GRADE manganese ore, from which manganese is obtained commercially, is not found in large quantities in any major steel-producing nation in the free world. The U. S. is a "have not" nation with respect to deposits of directly mineable high-grade manganese ore. Known resources of 48 pct Mn or better grade ore amount to less than 200,000 tons. In 1950 the U. S. steel industry consumed 1.8 million short tons of metallurgical grade manganese ore that contained about 800,000 tons of manganese. About 16 pct of the manganese content was lost in processing, so that about 650,000 tons, or 13 pounds per ton of steel actually entered into steel production. Under present practices use expands directly with steel output, and by 1975 the demand in both the U. S. and the rest of the free world is expected to be roughly 60 pet greater than in 1950. In peacetime about 80 pet of manganese consumption goes into steel production; high-manganese steel, dry cells, and chemicals account for the remainder. The manganese supply problem centers around high-grade ore for ferromanganese production. Use of ores containing less than 35 pet Mn sharply increase the costs of making ferromanganese. Use of ferro-manganese of grade below 70 pet in turn requires changes in steelmaking that increase steel cost. Under normal conditions the present small domestic production cannot be expected to increase. Major resources in the U. S. consist of 12 low-grade deposits. The cost of mining and treating these ores to extract a product as good as that yielded by imported ores is at least twice and in some cases more than four times the 1951 price of foreign ores delivered to the U. S. However, as long as trade relations and overseas shipping are not interrupted, deposits in India, Africa, and Brazil can meet steadily increasing demand at approximately present costs. Cost considerations indicate that the U. S. should continue to rely upon overseas sources for its peace-time supply, and that this situation is satisfactory. But, this does not take into account the question of how the U. S. will be able to meet its needs in war. Position of the Rest of the Free World In 1950, free world steel producers outside the United States, with a steel output of 70 million ingot tons, consumed about 1.3 million tons of metallurgical-grade ore. Their manganese ore demand, expected to increase directly with steel production, will by 1975 be about 2.3 million tons. Russia possesses over half the known manganese ore reserves of the world and is producing twice the tonnage of any other country. It supplied more than a third of the U. S. manganese requirements up to 1938 and again in 1948, but by 1950 Soviet manganese exports to the free world had virtually ceased. The free world's supply of manganese now comes mainly from India and Africa. Somewhat over 10 pet of U. S. imports came from Brazil and Cuba. Security Considerations In the event of war the U. S. might be substantially cut off from 90 pet of present sources. Reduction in manganese specifications might cut consumption by over 10 pet without seriously affecting steel quality. By elimination of losses in the production of ferromanganese savings as high as 10 pet might be possible. But, wartime manganese requirements cannot be met through conservation alone. To meet possible future emergencies the U. S. should continue its comprehensive security program for manganese, including stockpiling and research on the economic use of low-grade ore, domestic ores, the recovery of manganese from slag and the reduction of manganese requirements in steel production. If this work, including additional pilot plant operation is pursued vigorously, it should be possible in an emergency to get an adequate supply of manganese from domestic sources. The national stockpile then can be looked upon as a source of supply during the period of at least 2 years required to reach full-scale production from low-grade resources. Ferromanganese Smelting In comparison with smelting of pig iron, ferro-manganese smelting is a very wasteful process. Under present ferromanganese blast-furnace smelting practice, about 8 pet of the manganese in the furnace charge is lost to the slag, and roughly the same amount is lost to the stack gases; the total loss approaches 15 pct. Present practice is a compromise between excessive slag loss and excessive stack loss. In fact, it may be seriously questioned whether conventional blast furnace design is suitable for manganese smelting. U. S. Resources The known manganese deposits of the U. S. contain a total of 3500 million long tons of raw material and 75 million long tons of metallic manganese. More than 98 pct of this contained metal is in 12 large low-grade deposits of which the most important are those at Chamberlain, S. Dak; Cuyuna, Minn.; Aroostook County, Maine; and Artillery Peak, Ariz. Reserves of high-grade ore (48 pct Mn) amount to less than 200,000 tons. About 20 million tons of ore average over 15 pct Mn, and when grade is decreased to 10 pct Mn reserves amount to about 100 million long tons. If cut-off grade is decreased to 5 pet Mn, resources amount to 800 million long tons. Many of these low-grade ores may be beneficiated by flotation or other concentration methods. Pyrometallurgical Methods For smelting ferromanganese, it is essential to have an ore containing at least 50 pct manganese, with an Mn:Fe ratio of about 8:1. Direct smelting of 20 pct Mn concentrates is not promising. The only method that offers any promise involves two-step smelting.

Jan 1, 1952

By Thomas S. Blair

I FEEL a certain sense of responsibility in bringing before you the subject of the direct process in iron manufacture. I am aware that, in such a body as I have now the honor of addressing, there are few who are not already so well informed upon its past history that it would be a weariness to them to listen to anything else than an account of practical success. Yet, to claim that success involves so much that, if I do not make good my claim, I deservedly expose myself to severe criticism. The whole literature of the art, so far as it relates to the direct process, is, up to this time, but a history of failure. It is safe to say that more money, time, and talent have been fruitlessly spent in the pursuit of this object than in all the other unsuccessful efforts in the whole line of iron metallurgy. A distinguished authority in patent law has remarked that " the invention records of the United States and of foreign countries are filled with the waifs and abandoned relics of these abortive struggles." Dr. Percy, whose great work may be taken as an epitome of all that was worth mention, whether useful or curious, in pig-iron metallurgy, up to the date of its publication (1864), after giving elaborate accounts of various attempts at the direct process, condenses his own opinion of all that had been then effected, into a brief but summary comment upon a pamphlet of one of the sanguine inventors who had said: "It is evident that the present mode of working iron

Jan 1, 1874

By M. C. Manderson

The sharp drop in world phosphate demand that took place in 1975 due to temporarily high prices, now seems to be reversing itself. And prices for both phosphate rock and phosphate fertilizers, which declined dramatically from their 1975 highs, now appear to be bottoming out. This recent price weakness has delayed new mining ventures that had been planned for completion by around 1980. While there is ample capacity to supply near-term rock needs, the stage seems to be emerging for a better supply-demand and price environment in the late 1970's and early 1980's.

Jan 1, 1979

By C. E. Tsoutrelis

A new method for determining rock drillability in diamond drilling is discussed; the method takes into consideration both penetration rate and bit wear. The method is based on drilling a rock specimen under controlled laboratory conditions using a model bit. The technique used for determining the experimental variables is extremely simple, quick, and reliable. Drillability is then determined by the mathematics of drilling. In considering the different factors that affect diamond drilling performance, the nature of the rock to be drilled is of outmost importance since it affects significantly the drilling costs and such other variables as bit type and design, drilling thrust, and bit rotary speed. Many attempts have been made to study this effect by correlating actual drilling performances either to certain physical properties of the rock being drilled1-? or to test drilling data obtained under laboratory conditions.7-13 These attempts were aimed at providing a reliable method of predicting by simple means the expected rock behavior in actual drilling, thus giving the engineer a tool to use in estimating drilling performances and costs in different types of rock. The purpose of this paper is to describe such a method by which rock drillability (a term used in the technical literature to describe rock behavior in drilling) could be determined in diamond drilling. It is believed that the proposed simple and reliable method will cover the need of the mining industry for a workable method of measuring the drillability of rocks. It should be emphasized, however, that since drill-ability depends on the physical properties of rock and each drilling process (diamond, percussive, rotary) is affected by different or partly different rock properties,14-l6 the proposed method of determining rock drillability cannot be extended to the other drilling processes. The results presented in this paper form part of an extensive three-year research program carried out by the author in the laboratories of the Greek Institute of Geology and Subsurface Research. During this period the effects of the physical properties of rocks and of such operational variables as drilling thrust and bit rotary speed in diamond drilling were investigated in detail. DRILLABILITY CONCEPT The literature is not devoid of drillability studies. While there are a number of investigators1,3,5-7,9-0,12-13,17 who have attempted to establish by direct methods (i.e., drilling tests under laboratory conditions) or indirect (i.e., through a physical property of rock) an index from which the drilling performance in a given rock may be estimated, very few6-7,9,12, of the proposed methods seem to be of much practical value to the diamond drilling engineer and none to date has been universally accepted. Commenting on the proposed methods for assessing rock drillability, Fish14 remarks that "for a measure of drillability to be accepted it is essential that penetration rate at a given thrust and bit life are elucidated as otherwise the method is of little value." This statement should be examined in more detail by making use of the penetration rate-drilling time diagram obtained in drilling a rock under constant operational conditions. Furthermore, the merits of using this diagram to describe rock drillability will be pointed out. At the same time reference will be made to this diagram when discussing some previously proposed methods. Fig. 1 illustrates such a diagram for three rocks,A, B, and C, which have been diamond drilled under identical conditions. It is assumed here that rocks A and B have the same initial penetration rate, i.e., VOA = Vog, but since rock B is more abrasive than A, rapid bit wear occurs and as a result the fall of its penetration rate with respect to time is more vigorous than in rock A. This is shown graphically by a steeper V = f(t) (0 curve in this rock than in rock A. Rock C has a lower initial penetration rate, due to higher strength properties16 but since it is not very abrasive, only a slight fall of its penetration rate occurs during drilling (in this category are some limestone and marbles with compressive strength above 1000 kg per sq cm). It follows from the foregoing considerations that the characteristic for each rock curve (I) is a function of (i), the penetration rate of the rock Vo recorded at the instant of commencing drilling, which determines the starting point of the curve (1) on the y-axis and (ii), the abrasive rock properties which determine the rate of fall of Vo with respect to time. Thus, curve (I) provides an actual picture of the rock behavior in drilling for given operational conditions, and it can be used with complete satisfaction to assess rock drillability. It can be seen clearly from Fig. I that proposed methods for assessing rock drillability by measuring the

Jan 1, 1970

By Paul M. Tyler

THE farmer pays the phosphate miner! Phosphorus is used in fireworks; goes to battle in military smoke screens, incendiary shells, and tracer bullets; and, in vermin destroying pastes, does its part in the war against insects. A lemon phosphate can be had for a nickel at most soda fountains, and tens of thousands of tons of phosphate rock are mined annually for use in the food industries, chiefly for making monocaleium phosphate baking powder. Sodium phosphate cleaning, washing, and scouring compounds consume substantial quantities: the iron and steel industries buy a few thousand tons yearly to make ferrophosphorus and to balance foundry-iron furnace charges; and even nonferrous metallurgists use a little for phosphor bronze and other alloys. Phosphoric acid, its salts, and diverse other derivatives of this versatile element have countless applications, and industrial outlets are increasing rapidly, especially in the United States. Nevertheless, in this country nearly 90 per cent and in the whole world fully 95 per cent of the phosphate rock consumed is absorbed ultimately in agriculture.

Jan 1, 1938

By J. Ehner Thomas, M. D. Gould

Until four years ago the market price of oil securities moved directly and immediately with the general list. This point, was first developed by the senior author in 1924 while making a statistical study of the relative movement of oil securities and the general market. Plotting the monthly averages of 17 oils against 233 industrials disclosed the sur- prising relationship shown in Fig. 1. The traditional vagaries of the oil business, the wide fluctuations in current supply and resulting abrupt changes in crude prices nevertheless produced no movements in the market price of oil securities as a group, which departed notably from the movements of the general market. Obviously general business conditions did not always change when and as conditions in the oil industry changed; clearly the fluctuations of

Jan 1, 1929

The paper relates to the laboratory and pilot plant studies that have been carried out by Sherritt Gordon Mines Ltd., Metallurgical Research Div., in developing the ammonia pressure leach process for extracting Cu, Ni, Co, and S from high grade Ni concentrate produced from Lynn Lake ores and describes in some detail the chemistry of the process. In the leaching stage air, ammonia, and sulphide minerals react in a sequence of inter-related steps to produce soluble amines of Ni, Cu, and Co in a solution containing sulphate, thiosulphate, polythionate, and sulphamate ions and a controlled amount of free ammonia, the iron and other components of the concentrate remaining as an insoluble residue which is separated from the leach solution by filtration. The pregnant solution produced in leaching is further treated by boiling to precipitate and remove Cu as cuprous sulphide, leaving a copper-free solution with a composition suitable for subsequent precipitation of Ni and Cu by H,

Jan 3, 1955

By A. V. UDELL

OF all the metals that have from time to time been called the "Wonder Metal," mercury, often called quicksilver, is probably the most deserving of this designation. A wonder metal it must have been to those workers of an earlier day who named it after that Latin god of commerce and gain, characterized as the fleet messenger of the gods and the conductor of souls to the lower world. The word mercury has been used to indicate a carrier of tidings, a bearer of news, a nimble or clever person, a hawker, and a skillful thief. All of these attributes, and more, are recognizable in this metal, the technical terminology of which is "Hydragyrum," meaning water-silver, and from which the chemical symbol "Hg" is derived. Fickle in its occurrence in nature, simple in its metallurgy, illusive in captivity, it serves man in life or death, in war or peace, in commerce, science and arts, in mining, agriculture, and forestry with a versatility found in no other element.

Jan 1, 1929

By J. B. Austin

In considering so complex a process as the smelting of iron in the blast furnace, there is obviously no single method of calculating efficiency that gives a complete appraisal of the performance of the furnace in all its several functions; such a comprehensive view as is required to evaluate producing ability and manufacturing costs for a given furnace is obtained only by considering a group of efficiencies, each of which measures the performance of the furnace from a specific point of view. For instance, there is the rate of consumption of coke per ton of iron produced, which is probably the most frequently considered, and is certainly one of the most important of the group; there is the efficiency of recovery of iron charged; and there is the efficiency of utilization of energy, both chemical and thermal, in some respects related to the former two yet in other ways independent of either. In each of these cases, the calculation can be made on the basis of the actual input of material or energy, or it may be based upon a comparison with the minimum amount of material or energy that would be required by a "perfect" furnace; that is, an imaginary ideal furnace analogous to the perfect steam engine used in thermodynamic calculations, when this furnace is operating under optimum conditions. Moreover, the furnace itself can be considered either as an apparatus for smelting iron or, taking a somewhat less common point of view, as a gas producer yielding iron and slag as by-products. Some of these efficiencies are more useful than others, yet all are instructive; for a knowledge of them not only leads to good engineering practice from the standpoint of control but also discloses limits to possible improvement in performance and indicates the lines along which improvement is most likely to be profitable. Estimates of some of these efficiencies have appeared from time to time in the literature, but many of them are open to objection because they are based on data of uncertain accuracy or because they have been calculated without due regard to the thermodynamic principles involved. Moreover, so far as the author is aware, no general survey of the blast furnace comparing its performance in all the aspects mentioned has been made.

Jan 1, 1938

By R. H. Card

THE geophysicist is interested greatly in the resistivities of different formations or parts of the earth's crust; sometimes he is interested in a single figure in the nature of an average, or what may be called the effec-tive resistivity, of all the formations or parts of the crust at a given location to a certain depth. Conversely, the engineer whose work is concerned with the coordination of power and communication lines in such a manner as to avoid electrical interference between these two types of facilities is concerned very much with this effective resistivity; to a lesser extent he is interested in the resistivities of individual forma-tions. In connection with his work the coordination engineer often estimates the effective resistivity; of the earth from measurements of the mutual impedances of lines; in other instances he derives front measure-ments of a different type the resistivities of different layers of the crust and synthesizes these to obtain an estimate of the effective resistivity. In connection with problems concerning the coordination of power and telephone lines, measurements from which earth resistivities can be estimated have been made at many points in the United States by the American Telephone and Telegraph Co. and its associated companies, in cooperation with various power companies and with railroad companies having electrified sections of line. Other such measurements have been made by the Joint Subcommittee on Development and Research of the Edison Electric Institute and the Bell Telephone System. A study has been made of the correlation of these data with the ages and types of materials of the strata of the earth's crust at each of the test locations. The purpose of this study has been primarily to provide information to assist in predicting the order of magnitude of effective resistivities to be used in the preliminary consideration of problems con-cerned with the coordination of power and communication lines. To make the results of such a study, most useful, it is essential that the geo-logical data to be secured when such a prediction is wanted be readily obtainable. Data on the ages of strata and the types of materials com-posing geological structures can usually be obtained, therefore particu-

Jan 1, 1937

By Paul E. Rosten

Introduction This papers describes some of the latest improvements that have been incorporated or planned by the Cleveland-Cliffs Iron Co. to reduce operating costs and improve pellet quality. The Cleveland-Cliffs Iron Co. operates and manages mining, beneficiation, and pelletizing operations in Michigan, Canada, and western Australia. This paper deals with the grate-kiln pelletizing operations at Republic, Humboldt, Tilden, Empire, and Pioneer in Michigan, and the Adams and Sherman in Ontario, Canada. Table I characterizes each operation in regard to location, ore type, pellet capacity and date that pellets were first produced. All of the operations with the exception of Pioneer and Tilden, utilize downdraft-two-pass grate cycles of drying followed by preheating. Pioneer utilizes an all-downdraft, three-pass grate cycle which consists of three drying zones followed by the preheat zone. The Pioneer and Tilden cycles have been described previously (Lindroos and Koski, 1966; Villar and Dawe, 1975; Koski, 1977). Tilden utilizes a three-pass grate cycle with a stage of updraft drying, followed by two downdraft drying stages. Recuperation systems which supply hot gases to a drying zone from second stage cooling were designed and fur¬nished for Tilden I. Tilden II will be identical. Empire IV will also be furnished with a recuperation system. The Adams grate¬kiln system was retrofitted with a recuperation system. This paper will summarize some of the efforts that are in effect or planned for grate-kiln pelletizing systems to: (1) reduce operating and maintenance costs, (2) reduce energy requirements, (3) improve product quality, and (4) meet environmental standards.

Jan 1, 1981