Search Documents

By C. E. Berry

Natural stone or manufactured porcelain pebbles are used as the grinding elements in pebble mills and the mills are lined with stone or porcelain blocks. Steel balls usually form the grinding medium in ball mills, and the mills may be lined with steel. Pebble mills are used to avoid contamination by metal of the material being ground, to avoid rapid wear due to corrosion, and for other specialized reasons. Belgian silex (silica) blocks formerly were used widely for lining pebble mills, because of their good resistance to wear, light color, and low cost, but the importation of these blocks was suspended early in the war. The stocks of Belgian silex diminished so rapidly that it was found desirable to compare the properties of a number of domestic substitutes for use in critical operations. Accordingly, a study was made to determine the best substitutes for fine grinding of white pigment and for certain heavy-chemical process work such as the disintegration of phosphate rock in weak phosphoric acid solution. A comprehensive survey of substitute lining materials was not contemplated. It was stipulated at the beginning of the investigation that only materials on the market, available in large quantities, would be tested and that these should be reasonable substitutes from a a ance viewpoint as determined from known physical characteristics. Marble and limestone, for example, could be eliminated immediately. Quartzite, granite and porcelain were selected as likely substitutes for Belgian silex and were subjected to quality tests. Materials Tested 1. Belgian Si1ex.—Sample blocks of a standard grade were taken from crates in which they had been imported. The stone was light gray in color and contained inclusions of small clusters of quartz crystals as well as light colored portions that might be calcite. This was a siliceous rock which appeared to be of igneous origin. 2. Quartzite.—Samples of quartzite were obtained from a quarry in Minnesota. The blocks exhibited a crystalline fracture. The stone was pink in color and composed of fine quartz crystals bound together with a siliceous cement. 3. Granite A was a fine-grained granite quarried in South Carolina. 4. Granite B was coarse-grained granite quarried in South Carolina. 5. Granite C was a coarse-grained granite quarried in North Carolina. 6. Porcelain A.—Sample blocks of the pebble-mill lining material were obtained direct from the manufacturer. It was white in color and of lower specific gravity than the natural materials. It did not have a crystalline structure. 7. Porcelain B.—Sample pebble-mill lining blocks of the porcelain were received direct from the manufacturer. It was white

Jan 1, 1948

By C. E. Berry

Natural stone or manufactured porcelain pebbles are used as the grinding elements in pebble mills and the mills are lined with stone or porcelain blocks. Steel balls usually form the grinding medium in ball mills, and the mills may be lined with steel. Pebble mills are used to avoid contamination by metal of the material being ground, to avoid rapid wear due to corrosion, and for other specialized reasons. Belgian silex (silica) blocks formerly were used widely for lining pebble mills, because of their good resistance to wear, light color, and low cost, but the importation of these blocks was suspended early in the war. The stocks of Belgian silex diminished so rapidly that it was found desirable to compare the properties of a number of domestic substitutes for use in critical operations. Accordingly, a study was made to determine the best substitutes for fine grinding of white pigment and for certain heavy-chemical process work such as the disintegration of phosphate rock in weak phosphoric acid solution. A comprehensive survey of substitute lining materials was not contemplated. It was stipulated at the beginning of the investigation that only materials on the market, available in large quantities, would be tested and that these should be reasonable substitutes from a a ance viewpoint as determined from known physical characteristics. Marble and limestone, for example, could be eliminated immediately. Quartzite, granite and porcelain were selected as likely substitutes for Belgian silex and were subjected to quality tests. Materials Tested 1. Belgian Si1ex.—Sample blocks of a standard grade were taken from crates in which they had been imported. The stone was light gray in color and contained inclusions of small clusters of quartz crystals as well as light colored portions that might be calcite. This was a siliceous rock which appeared to be of igneous origin. 2. Quartzite.—Samples of quartzite were obtained from a quarry in Minnesota. The blocks exhibited a crystalline fracture. The stone was pink in color and composed of fine quartz crystals bound together with a siliceous cement. 3. Granite A was a fine-grained granite quarried in South Carolina. 4. Granite B was coarse-grained granite quarried in South Carolina. 5. Granite C was a coarse-grained granite quarried in North Carolina. 6. Porcelain A.—Sample blocks of the pebble-mill lining material were obtained direct from the manufacturer. It was white in color and of lower specific gravity than the natural materials. It did not have a crystalline structure. 7. Porcelain B.—Sample pebble-mill lining blocks of the porcelain were received direct from the manufacturer. It was white

Jan 1, 1948

By Bezalel C. Haimson

We have developed a new wireline hydrofracturing technique for in situ stress measurement which eliminates the need for drill rig and drill rod and renders the tripping of the straddle or impression packers continuous, fast, and inexpensive. Wireline conductors facilitate the use of downhole pressure transducers. We have confirmed the suitability of the new technique by testing it in a deep hole near the Monticello Reservoir, South Carolina. Our measurements indicate two local stress fields, one of them apparently linked to the impoundment-related induced seismicity.

Jan 1, 1984

By Frank Firmstone

By J. B. Darby, P. A. Beck

IN a previous publication,' the 1200°C isothermal section of the Cr-Mo-CO system was surveyed. It was found that starting from the binary (Cr,Co)a, the u phase extends deep into the ternary system in the form of a narrow band, which, when extrapo-

Jan 1, 1956

By James L. Hendrix, Pat Vreeland, Hamilton Vreeland, Marcel F. DeGuire, Peter L. Comanor

A study of the ground area surrounding the Getchell, Nev., gold mine mill tailings was conducted so that a better understanding of the effects of arsenic toxicity on Upper Sonoran vegetation could be obtained. The Getchell area was selected because of the known high values of arsenic currently contained in the tailings waste (1% or higher). Mill wastes as well as the scrubber product As2O3 are contained in the tailings pond. In order to determine the effect of the tailings disposal on the surrounding vegetation, plots and line-transect techniques were employed to obtain plant ecological information on the area surrounding the ponds, and also non-affected control plots. Data for percent ground cover, species frequency, and plant vitality as a function of distance from the tailings ponds were collected. In an attempt to isolate naturally occurring factors for varying plant communities from induced factors derived from the close proximity of the tailings, soil cores were

Jan 1, 1975

By P. E. Price, N. J. Grant

DURING the course of creep studies in iron-chromium-nickel alloys, it became necessary to establish the limits of the two-phase ferrite-austenite field at 1300°C. The shape of this region, predicted from the iron-chromium and chromium-nickel binary

Jan 1, 1960

By George I. Smith

Jan 1, 1985

By H. M. Katz, J. L. Speirs, F. B. Hill

Jan 1, 1961

By J. S. Billheimer, H. H. Reamer, B. H. Sage

Jan 1, 1949

By H. H. Reamer, B. H. Sage, J. S. Billheimer

Jan 1, 1949

By Radoslav Despotovic

The developed radiometric method of particle system analysis has been applied to investigate the bulk properties of particles precipitated from solutions. The nature and principles of the method applied are described briefly, and some possible models in the field of fine colloid particles precipitation discussed. Changes in radionuclide distribution were followed during the solid phase formation and the data were used to calculate changes in bulk composition of colloid precipitates. The radiometric data show interesting phenomena closely connected with the characteristic of bulk particles. The measured radiometric data are highly reproducible, the applied methods have proved to be sensitive, and the developed techniques have been tested by various standard procedures.

Jan 1, 1980

By L. J. Murphy

The production of crude oil in the United States is exceeding consumption by one-quarter million barrels per day and, with the possibilities of West Texas, this condition of overproduction, unless controlled, is likely to continue for some time. The resulting low price of oil has caused the operator to observe closely his lease operating costs. The installation of more efficient and reliable machinery has followed and it can well be said that the art of producing oil is on the threshold of a new era. In this advancement electricity has played a leading part. This paper covers only the problem of electricity as applied to lease operation and does not consider other phases of the industry, such as drilling and pipe-line pumping, in which electric power has been utilized economically. In considering electrification of pumping wells, the first question the operator asks is whether or not his costs will be reduced and the second question is whether or not the production will be increased. The third question, although in effect it is closely allied to the first, is the cost of power. The last question can be answered only after a thorough analysis of operating conditions and a study of the power rates prevailing in the particular field under consideration. Within the past few years, the power companies have realized the desirability of a steady 24-hr, pumping load, have made their rates for oil-field service particularly attractive, and in general have shown splendid cooperation in assisting the oil companies in the satisfactory application of electric power to their leases. When everything is taken into consideration, the first cost is practically the same for electric drive as for gas engines when pumping on the beam with individual motors. This cost, at prevailing prices, should aver-age approximately $2200 to $2400 per installation when using 15 to 35-hp., two-speed pumping equipment, including motor and control, countershaft, motor house, belt, installation charges, and a prorated portion of the cost of transmission lines and transformers for serving a number of wells. Since there is practically no difference in the cost of the two installations, it is evident that electricity, to justify its consideration, must have a lower operating cost or produce more oil.

Jan 1, 1928

By Ernest Kirkendall

The amount of research done in the last fen years on the subject of diffusion in solid metals is significant of the importance of this problem. To review the literature dealing with diffusion is unnecessary here. Deschl in 1912 reviewed the work that had been done on diffusion in solids and gave a bibliography of the literature published before that time. Mehl's paper in 19362 is an excellent review of diffusion in metals and contains a large bibliography. Of importance also for it? review and bibliography is an article by 14. I. Krynitsky.~ While considerable material lias appeared in the literature on diffusion in brass, the amount of information is not great compared to that pertaining to some of the other alloys. Most of the information published is of a qualitative nature; that which is quantitative varies considerably. Thus the quantitative determination of the rates of diffusion of copper and zinc in alpha brass by a new method appeared worth while. In the present investigation the rate of diffusion of zinc in approximately the same composition alpha brass has been determined :it three temperatures. Procedure The method used consisted of plating copper on a beta brass, heating it, to allow diffusion to take place, and measuring the concentration of copper by determining the lattice constant of the alloy. This method is unique in that it uses a beta brass of such a composition that at the tem perature at which diffusion takes place the beta brass is saturated wit11 copper. Thus, while the beta brass supplies thc zinc, no diffusion takes

Jan 1, 1939

By Ernest Kirkendall

The amount of research done in the last fen years on the subject of diffusion in solid metals is significant of the importance of this problem. To review the literature dealing with diffusion is unnecessary here. Deschl in 1912 reviewed the work that had been done on diffusion in solids and gave a bibliography of the literature published before that time. Mehl's paper in 19362 is an excellent review of diffusion in metals and contains a large bibliography. Of importance also for it? review and bibliography is an article by 14. I. Krynitsky.~ While considerable material lias appeared in the literature on diffusion in brass, the amount of information is not great compared to that pertaining to some of the other alloys. Most of the information published is of a qualitative nature; that which is quantitative varies considerably. Thus the quantitative determination of the rates of diffusion of copper and zinc in alpha brass by a new method appeared worth while. In the present investigation the rate of diffusion of zinc in approximately the same composition alpha brass has been determined :it three temperatures. Procedure The method used consisted of plating copper on a beta brass, heating it, to allow diffusion to take place, and measuring the concentration of copper by determining the lattice constant of the alloy. This method is unique in that it uses a beta brass of such a composition that at the tem perature at which diffusion takes place the beta brass is saturated wit11 copper. Thus, while the beta brass supplies thc zinc, no diffusion takes

Jan 1, 1939

By E. E. Gardner, P. A. Schumann

A description of a new four-point probe configuration which permits measurement of epitaxial layer resistivity is given. An analytic solution to the potential distribution due to a point current source on a multilayered structure is briefly described. Typical solutions for this probe configuration are presented. Probe spacing, layer thickness, substrate resistivity, and substrate thickness enter into the calculation. Correction factors for typical cases are given. A brief description of the construction of a probe which can achieve a small spacing of 15 is presented. The prohe is constructed so that all points are adjustable by micrometers and the probe spacing and configuration can be easily altered. Measurements of layer resistivity with the four-point probe are compared with those taken with the three-Point probe and diode-capacitance techniques. TWO techniques of obtaining profiles of N/N+ epitaxial structures are given. The reproducihility of the probe spacing and resistivity measurement is discussed. The effects upon the resistivity measurement of errors in the measurement of the lager thickness, substrate resistil)itv, and substrate thickness are presented. SINCE its introduction by valdes' in 1954, the four-point probe has been the most widely used tool for determining semiconductor resistivity. Its usefulness ranges from the evaluation of bulk semiconductor ingots to the characterization of impurity profiles in diffused structures. In general the four points, two current probes and two potential probes, are placed on one surface of the material being tested either in an in-line array or in a square array. Numerous correction factors1 8 have been worked out for these configurations which are dictated by the finite geometry of the sample being tested. One method of evaluating thin wafers has been proposed which has two probesg on each side of the wafer. Further modifications have added a fifth'' and a sixth" probe. One paper1' has discussed the accuracy of the four-point probe and the precautions necessary in its use. With the exception of the method where two points are placed on opposite sides of the wafer, the four-point probe is restricted to evaluation of wafers with a homogeneous resistivity or to the case where an isolating junction exists between the substrate and the layer (epitaxial or diffused) being evaluated. Due to the relative resistivities and thickness, the resistance of the epitaxial layer is much greater than that of the substrate, and consequently a majority of the current flows through the substrate. The potential distribution at relatively large distances from the current sources is determined by the substrate resistance, and hence the AV/I value is a measure of the substrate resistivity and not that of the epitaxial-layer resistivity. In the immediate vicinity of a current source the potential distribution is determined by the layer resistivity among other factors. Consequently, if the potential probe is placed very close to the current source, then with appropriate correction factors it is possible to determine the layer resistivity. This was the theoretical basis for using two closely spaced probes on opposite sides of an epitaxial wafer. However, due to mechanical problems, it is desirable to place the four probes on the same side of the wafer. This paper discusses the potential distribution in

Jan 1, 1965

By Samuel S. Wyer

1. The following is an abridgment of a recent report made by the author, covering an investigation of: (A) The necessary use of natural-gas compressors; (B) The effect of gas compressors on natural-gas field operating conditions in Ohio, with special reference to the working pressure relations of gas wells of one company discharging by natural rock-pressure flow without compressors, and adjacent wells of other companies, discharging into intake lines to gas-compressing stations. Tests were made at 107 different places in the counties of fairfield, Licking and Knox, Ohio, which required 7,000 miles of automobile driving, and consumed 6 months' time. 2. A proper conception of the necessary use and effect of natural-gas compressors in natural-gas production necessitates a clear understanding of certain fundamental definitions and judicial doctrines, which are given herein. 3. Gas is a fluid composed of a large number of molecules which are vehicles of energy continually in motion, and havingan inherent tendency to get farther and farther apart. The range of motion of the molecules is limited only by the volume of the closed containing vessel in which they constantly move to and fro. The most distinguishing characteristic of gas is its universal property of completely filling an inclosed space. 4. Gas pressure is the result of the combined efforts of all the moving molecules in the mass trying to get farther and farther apart, that is, a mass of gas inclosed in a vessel expands and fills it, and being restrained from further expansion, it exercises a pressure against the walls of the vessel. This pressure is the same in all directions on equal areas of surface, as shown in Fig. 1. With a given mass of gas, any increase in volume of containing vessel will give the molecules more range of motion, * The public's interest in the age and magnitude of the art of gas compressing and development of the law relating to the use of grs compressors in natural gas production is discussed in the preceding paper. Development of the Law Relating to the use of Gas Compressors in Natural Gas Production; see also Is It Feasible to Make Common Carriers of Natural Gas Transmission Lines, vol. xlviii, 471 to 480 (1914). Consulting Engineer.

Jan 1, 1916

By E. O. Bennett

When oil is takcn from a subsurface structure it is generally accompanied by gas. The gas thus produced represents the 1ighter hydrocarbons present in the original petroleurn accurnulation, which arc, insoluble at the reduced pressures created around a well when it is producing. In some cases the gas accompanying the oil may come from a gas-bearing stratum not in immediate contact with the oil. The amount of gas from the formation accompanying each barrel of oil is called the natural gas factor. Energy Causing Well to Flow The force causing the flow of fluid into a well when it is drilled into an oil-bearing structure is the pressure differential between the well bore and the formation. A pressure differential between the formation and the well may be set up in three different ways, as follows: (1) pressure due to gas in solution or in contact with the oil, (2) hydrostatic pressure due to water in contact with the oil (it may be either bottom or edge water); (3) pressure difference due to forcc of gravity. The greatest source of energy for producing oil from most oil fields, and the one over which the greatest control can be exerted, is the poten-tial energy in the gas under pressure in the formation. In any pool there is but a definite amount of gas available. Part of this gas may be in solution and a part in contact with oil. The amount of gas in solution in each bard of oil depends on the pressure and temperature in the formation and the characteristics of the oil. Whether the gas is in solution or in contact with the oil it is necessary to use the energy it, contains as efficiently as possible in order to obtain the greatest ultimate recovery from the pool. Bush1 states: Gas being the most efficient aid in moving the oil, it is important to prevent more of it from escaping than is necessary to remove the maximum amount of oil from the sands. The conservation of this energy is far more important to the producer of oil than his returns from sales of gas to distributing companies. The flowing life of the well is the most profitable period, and keeping the gas-oil ratio low, or keeping the

Jan 1, 1928

By J. Chipman, N. J. Grant, B. M. Shields

The vacuum tin-fusion method of analysis for hydrogen, developed by Carney, Chipman, and Grant, has been modified to permit the analysis of the evolved gases for hydrogen by means of a thermal conductivity cell. A properly prepared sample can be analyzed in 10 min with a probable error of ±0.12 ppm. A study of various methods for storage of hydrogen samples shows that samples can be safely held in a dry ice-acetone bath as long as six days. Storage in liquid nitrogen is necessary for samples to be held one week or more. HE vacuum tin-fusion method, as developed by I- Carney, Chipman and Grant,' is the only analytical procedure which has shown promise of being fast enough for use in the control of hydrogen during steelmaking. It was felt that further simplification and faster speed of operation could be effected by the use of thermal conductivity measurements for analysis of the gases evolved in the tin-fusion method. The application of conductivity measurements to the tin-fusion method is possible because: 1—the evolved gas is essentially a mixture of hydrogen, nitrogen and carbon monoxide with a hydrogen content usually over 50 pct, 2—the evolved gas is collected at a relatively low pressure, and 3— the thermal conductivities of CO and N2 are practically identical while that of hydrogen is very much greater. The major part of this research program was devoted to the construction and calibration of a vacuum tin-fusion apparatus which analyzes the evolved gases for hydrogen by means of a thermal conductivity cell. The second phase of the problem was associated with the development of a procedure for storage of samples prior to analysis. With the rapid quenching method for hydrogen sampling,' which seems to be the most practical for steel mill use, it is necessary that the samples be stored safely during the interval between sampling and analysis if the hydrogen content of the molten metal is to be maintained in the supersaturated solid samples. The thermal conductivity bridge has been used for a number of years in the analysis of certain gas mixtures. An elementary discussion of the theory and practice of gas analysis by thermal conductivity measurements is given by Minter.3 A more comprehensive discussion of the theory and of the various measuring circuits is presented by Daynes.' A complete knowledge of the theory and properties of the thermal conductivity of gases and gaseous mixtures can be gained by a study of the standard textbooks on the kinetic theory of gases."' The existing data on the thermal conductivity of single gases are reviewed by Hawkins: that for a number of binary gas mixtures by Daynes' and Lindsay." The thermal conductivity method may be applied to the determination of the composition of a binary mixture if: 1—the thermal conductivity of the mixture varies monotonically with composition, and 2— the two gases have measurably different thermal conductivities. The greater the difference between the two gases, the greater the sensitivity of the method.10 he method is applicable to the analysis of multicomponent mixtures when all of the gases in the mixture except one have nearly the same thermal conductivity. Fortunately, the mixture of hydrogen, nitrogen, and carbon monoxide evolved by the tin-fusion analysis' falls in this latter classification. The thermal conductivities of nitrogen and carbon monoxide are practically equal; and the thermal conductivity of hydrogen is approximately seven times that of the other two. Therefore, the thermal conductivity of a gaseous mixture of hydrogen, nitrogen, and carbon monoxide at known temperature and pressure can be related directly to the percentage of hydrogen in the mixture by suitable calibration. Usually the thermal conductivity of a mixture of gases is measured at atmospheric pressure where the thermal conductivity is independent of pressure over a wide pressure range. At very low pressures (below 1 mm Hg), the thermal conductivity of gases varies with the pressure. This phenomenon has been utilized in the Pirani vacuum gage for the measurement of pressures in the range of 10" to 10-0 mm of mercury.= Very little has been published concerning the variation of thermal conductivity with pressure at intermediate pressures between 1 mm Hg and 1 atm. However, preliminary measurements indicated that the thermal conductivities did vary with pressure over the range of pressures (up to 10 mm Hg) at which gases are delivered from the vacuum pump. Therefore, the calibration of the thermal conductivity cell had to be planned to include the effects of both gas composition and pressure. Such a calibration chart is shown in Fig. 4. Most industrial applications of the thermal conductivity method of gas analysis have used a compensated Wheatstone bridge circuit containing two

Jan 1, 1954

By P. Bardzil, J. Gurland

An experimental study of the variation of transverse-rupture strength with composition Anexperimentaland grain studysize has shown that the strength reaches a maximum for values of the mean free path between carbide particles of 0.3 to 0.6 microns. The fracture oforiginates in and proceeds through the carbide grains mainly. Impact strength and hardness also were recorded. MOST of the physical properties of sintered carbides vary linearly with composition. The transverse-rupture strength, however, shows a unique behavior. As the amount of binder metal is varied from 6 to 25 pct by weight, the strength at first increases; then, between 15 and 20 pct Co, it reaches a maximum of nearly 400,000 psi, and finally decreases with further additions of binder metal. This behavior of the transverse-rupture strength has been reported, among others, by Englel and Sandford and Trent.' The significance of these observations has not been discussed in the literature. That it may be of more than specific importance is indicated by the very similar variation of strength with composition encountered in other systems sintered in the presence of a liquid phase, such as Tic-Ni3 and Fe-Cu.' Experimental Details All compacts were prepared and sintered according to normal industrial practice. The average diameter of WC grains and the mean free path between grains were measured on metallographically prepared samples by a method of linear and planar analysis sing the relations where d is the average diameter of dispersed grains; Nl is the number of noncontiguous grains intersected on a metallographic plane by a line of unit length; N, is the number of noncontiguous grains per unit area; P is the mean free path between grains of dispersed phase; and f is the volume fraction of dispersed phase. Approximately 1000 grains were counted on each sample. For each composition d2 was plotted against P, the resulting straight lines serving as a check on the measurements. The distribution curves of the WC powders of different average diameters were homologous, and no attempt was made to influence the grain size by blending powders, adjusting the sintering conditions, or otherwise altering the particle size distribution. Densities were measured by differential weighings in air and water. The degree of densification did not vary consistently with either composition or grain size. The density is influenced by slight amounts of impurities, specifically by 0.1 to 0.2 pct Fe which enters the powders during ball milling. As an illus- -tration of the experimental variations, a number of measured densities are listed in Table I. They are expressed in percentage of theoretical density, as calculated from the published X-ray densities of WC and Co.' For the purpose of determining the transverse-rupture strength, rectangular test specimens (3/16x 3/8x3/4 in.) were broken by loading at the center of a 9/16 in. span. The average strength of five or more samples is reported for each composition and grain size. The compacts were ground on two parallel surfaces only. The load was applied at an average rate of 6,800 psi per sec. Since the elongation after fracture of the alloys is very small, it was assumed that the compacts deform elastically to failure and the fracture stress was calculated by the conventional beam formula. The data for one alloy are presented in Table II as an example of the results and scattering ranges encountered. The precision of the test, as measured by the average difference between duplicates, is of the order of 15,000 psi. The results are strictly comparable only to compacts prepared and tested in the manner described and of similar chemical composition and grain size characteristics. Unnotched Charpy specimens were used for impact testing. Each point represents the average of 3 to 20 samples, the larger number being used in an attempt to determine the influence of grain size. Considerable scatter was encountered, the range from lowest to highest value often amounting to 30 pct of the impact strength. The hardness is reported as a Ra reading, using a 60 kg load with diamond brale indenter. Compositions are given in weight percent.

Jan 1, 1956