Search Documents

By J. B. Austin

IN developing a consistent picture of the thermal expansion of the commercial chromium steels, which cover a range of carbon contents, it is desirable to know the expansion in the limiting case of the binary, carbon-free, iron-chromium alloys. We have, therefore, determined the thermal expansion of a series of five special alloys, ranging in chromium content from 3 to 10.5 per cent, with not more than 0.03 per cent carbon, over a temperature range extending beyond the transformation region; this low carbon content enables us to draw reasonably reliable conclusions as to the behavior of the carbon-free system. Moreover, the measure-ments serve to determine the beginning and the end of the alpha-gamma transformation; and they emphasize once more the fact that a transforma-tion temperature determined by any method in which the specimen is cooled at an appreciable rate is apt to be seriously in error, particularly if the metal contains a transformation-retarding element such as chro-mium or managanese. The lag, or undercooling, observed at the ? - a transformation is explained in terms of the influence of temperature on transformation velocity; the rather unusual shape of the ? loop is attributed to a change with temperature and with composition of the distribution of chromium between the alpha-iron and gamma-iron solid solutions. The exact composition of the alloys which were obtained through the courtesy of Dr. W. Rohn, of the Heraeus Vakuumschmelze A-G., is given in Table 1. Determinations of the linear thermal expansion and of transformation temperature were carried out in the vacuum dila-tometer previously described,1 using a rate of heating and of cooling of 3.0° to 3.5° per minute unless otherwise stated. Magnetic susceptibility, which was measured in studying the rate of transformation, was determined with a magnetic balance, which also has been described.2

Jan 1, 1935

By D. P. Morton

SINCE 1023, which closed the speculative era in the bituminous coal fields of the United States, there have been wide annual fluctuations in the national production of bituminous coal. These changes in annual output have been variously attributed to: (I) increased competition from petroleum products, natural gas and hydroelectric power; (2) lower unit consumption of coal; and (3) fluctuations in the general business level. The purpose of this paper is to measure, from a practical standpoint, the net effect upon the annual trend of bituminous coal production, and to give those who are interested a basis for estimating in advance the probable output of bituminous coal. It can readily be shown that changes in the level of general business affect the national production of bituminous coal more than does any other factor. Therefore it is necessary to use some standard measure of the relative business level for purposes of comparison. The Federal Reserve Board Index of Industrial Production offers the basis for such a measure.' This Index, a weighted composite of 81 different series, rests upon the averages of the years 1935 to 1939 as loo, and is presented graphically in Fig. I. Even a cursory examination of the chart will indicate a definite uptrend for industrial production over a period of years. This uptrend is due to at least two factors: (I) an actual increase in national population, and (2) a probable increase in the per capita consumption of goods. This means that there is no such thing as a fixed Normal, rather Normal is a variable, tending to increase from year to year. In order to measure the amount of annual increase in normal, the Index of Industrial Production must be studied in relation to its major components, Durable Goods and Nondurable Goods. Durable Goods are those made from the lasting materials such as iron, steel, other metals, lumber, stone, cement, clay, glass. Nondurable Goods are those for early consumption, such as foods, textiles, tobacco, chemicals, paper, gasoline, and goods made of leather and rubber. The purchase of Durable Goods may be postponed, but Nondurable Goods must be purchased currently unless the standard of living is lowered. The Federal Reserve Indexes of durable and nondurable goods are shown graphically, 1920 to 1939, on Fig. 2 (pp. 764-765 of ref. I). It is apparent that fluctuations in the production of nondurable goods are not nearly so wide as in the production of durable goods, and that the curve of Industrial Production (Fig. I) would fall between the two curves on Fig. 2. It would, however, seem logical that both curves should follow the same long-term trend, or that over a period of two to three decades the relative proportion of durable and nondurable goods, in periods of normal production, should he the same. It is neces-

Jan 1, 1941

By G. R. Fitterer

NonmEtallic inclusions in steel have received much attention by metallurgists during the past few years. Many investigators have been emphatic in stating their belief that these impurities are the chief causes of steel failures, while others think that their effects are negligible. One of the main reasons that definite information on the effects of these impurities is lacking is that no reliable method has been developed for the exact determination of the amounts of these different impurities in steel. Some valuable new information has been brought out by a reliable method for nonmetallic inclusions which has been developed at the Pittsburgh Experiment Station of the U. S. Bureau of Mines, in cooperation with the Carnegie Institute of Technology and the Metallurgical Advisory Board. This procedure satisfactorily extracts some of the more common inclusions from steels, thus enabling the investigator to correlate steel failures with inclusion content. Although the data given herein are the first to be published on the subject of the electrolytic extraction method, the interest in the subject is evidenced by the fact that it is already being used by some 20 to 30 steel companies for their various purposes. Some of the comments received from these laboratories indicate that the method is highly satisfactory: the unfavorable comments, when traced to their sources, have been found to be based on some small mistake made in either installation or operation. The chief discrepancy seems to have occurred in attempts to apply the method to the extraction of inclusions from alloy steels. The procedure can be used only for the plain carbon steels and for such low alloy steels as those containing the usual amount of copper (0.2 to 0.3 per cent). Steels containing the carbide-forming alloys such as chromium, tungsten, etc., present far too many difficulties for the accurate determination of inclusions. Luckily, the iron and manganese carbides do not offer any difficulties and no contamination of the oxide-sulfide residue results, It is highly probable that some modification of the following

Jan 1, 1931

By I. L. Greninger

THE property of the Andes Copper Mining Co. is in the central part of the Republic of Chile, Province of Atacama, 147 km. (91.5 miles) eastward by rail from the port of Chanaral. At this point the Andean system is made up of two principal ranges. The mine is on the westerly slope of the outer, or western, range, at a mean elevation of 3250 m. (10,500 ft.). A meter-gage railroad extends from the company's port at Barquito, near Chañaral, to the reduction plant at Potrerillos. This road has a total length of 151 km. (94.0 miles), of which 93 km. (57.79 miles) are owned by the Andes Copper Mining Co. The remainder of the road is owned by the state. The company operates its trains over the portion of the road owned by the state, under an agreement with the Chilean Government. The mine is connected with the reduction plant by a meter-gage railroad, 10 km. (6.214 miles) long, which extends from the coarse-ore bins at the metallurgical plant to the underground storage bins at the mine. Tunnels make up 60 per cent. of the total length of this railroad. As is characteristic of the Andean region in Chile, the topography of the locality is extremely rough, and a number of points near the mine have elevations of from 15,000 to 16,000 feet. History of Potrerillos Mine The ore occurrence has been known for many years, and many of the claims under individual ownership were worked in a small way before the property was acquired by the present owner—the Andes Copper Mining Company. The highest grade oxide ores near the surface were mined by primitive methods and, after sorting, the product, assaying around 15 per cent, copper, was hauled by mule carts a distance of about 80 km. (49.71 miles)

Jan 1, 1929

By Å. Sterten, R. Tunold, J. Brun, K. Dalatun

The subjects of this study are two corrosion phenomena familiar to operators of aluminum plants employing Soderberg anodes of the vertical type, namely the sul-fide scale formation observed at the steel contact spikes and the corrosion wear observed at the lower edge of the gas collecting skirts. The causes of these corrosion phenomena are discussed on the basis of observations from practice and measurements on commercial cells as well as on laboratory experiments. It is concluded that the anode spike corrosion is mainly due to the attack by sulfur compounds contained in the anodically evolved gases and that this attack is greatly promoted by cracks and pores in the anode carbon embedding the lower spike ends. The corrosion of the gas collecting skirt is mainly attributed to anodic dissolution of the iron during occasional contacts with the melt. ANODE SPIKE CORROSION The visible result of this corrosion is the formation of a brittle loosely adherent scale on the lower ends of the mild steel spikes maintaining the electric contact to the carbon anode, Fig. 1. The thickness of the scale usually varies from 0.5 to 3 mm, but in some cases scale of about 10 mm thickness has been observed by the writers. During the spike pulling, usually repeated every 3 weeks, part of the scale often loosens and remains in the anode carbon, resulting in contamination of the aluminum with iron. This corrosion has been attributed to reaction of the iron with gaseous sulfur compounds originating from the anode paste materials.'-4 This paste usually consists of 70 pct precalcined petroleum coke with 1.2 to 1.4 pct S and 30 pct coal tar pitch containing 0.5 to 0.7 pct S. During operation the gasification of the anode materials takes place in two ways: First, gases are evolved by the gradual baking of the anode paste added on top of the anode. Due to the sealing effected by the upper semifluid zone of the paste, these gases, containing sulfur compounds from the pitch, are forced downward through pores and cracks in the rigid anode carbon. At the temperatures of the zone of the lower ends of the spikes, 700" to 900°C, the original components of the baking gas must undergo decomposition, similar to that taking place with the production of coal gas, resulting in a gas mixture consisting mainly of H2 and CH4 with small percentages of H2S as the main sulfur compound.5 Second, the anodic reaction results in a mixture of C02 and CO, the total quantity of which is about 15 times that of the baking gas. These anode gases must carry the entire sulfur content of the carbon gasified by the anodic reaction. Henry and Holliday6 have shown that COS is the main sulfurous component of the anode gases from Soderberg cells. Soderberg anodes usually exhibit a network of vertical cracks, frequently traversing from one spike to the next one and to the outside of the block and widening downward to the working face of the anode. In addition the anode carbon, particularly that below the spike ends, is rather porous, as indicated in Fig. 1. It therefore seems probable that the anode gases also may partly penetrate to the spike ends. As the anode is partly immersed in the melt, the static pressure of this must forward this penetration. I) SPIKE SCALE COMPOSITION A great number of freshly extracted spikes from industrial plants were inspected and samples of the scale collected for examination. Before analyzing the samples a thin iron oxide layer, formed by air oxidation of the outside of the red hot scale immediately after spike pulling, was removed. On the average the Fe/S ratio found by these analyses corresponded to I the composition FeSl. oo7. X-ray powder patterns showed no oxide and otherwise agreed with those found by Haraldsen7 for iron sulfide with 50.00 at. Pct

Jan 1, 1970

By J. T. Brown

AS far as could be ascertained, no one had previously investigated the creep strength of silicon poly-crystals. Literature has appeared showing evidence for plastic deformation in silicon single crystals and whiskers.*1"6 Also the fact that germanium, a material of similar crystal structure to silicon undergoes plastic deformation under stress at temperatures above about 60 pct of its melting temperature, has been known for some time.2"4'7 This investigation was performed for the purpose of determining the strength and ductility of silicon polycrystals under creep conditions that would give fairly long times to rupture. PROCEDURE The silicon specimen blanks were obtained by first placing granulated transitor grade silicon (99.999 + pct pure) in a silica crucible. The crucible was surrounded by a graphite susceptor, and induction heating was used for melting the silicon in a vacuum furnace. Blank specimens were formed by freezing molten silicon onto a polycrystalline seed of silicon in a vacuum furnace. The seed was attached to a motor driven revolving rod. As silicon solidified, this rod was gradually withdrawn from the melt. A shape with a contracted center section was obtained by varying the rate of withdrawal from the melt. Specimens for the creep-rupture tests were ground from these "pulled" blanks. Creep-rupture tests were performed in spring loaded machines under constant load at 1800" and 2000° F. RESULTS AND DISCUSSION A test specimen which was sectioned longitudinally is shown in the photomacrograph in Fig. 1. Very little deformation has taken place in the portion of the specimen shown, however, slip lines from several slip systems within the same grain, and deformation band formation was seen. The elongated appearance of the grains is due to the method of growing the specimens. One of the most interesting aspects of the results obtained from the creep-rupture tests was the high strength and the accompanying large amount of ductility. The data obtained is listed in Table I which shows the stress to rupture in 100 hr at 2000°F is between 8000 and 9000 psi. This indicates that silicon's strength at 2000°F is about equal to that of the best commercial super-alloys. It is important to mention that silicon has less than 1/3 the density of iron-, nickel-, and cobalt-base alloys. The usual type alloys for high-temperature applications

Jan 1, 1960

By Reno H. Sales, Charles Meyer

AT Butte, successive zones of sericitized and argillized quartz monzonite occur around every ore-bearing fracture regardless of its size, attitude, or relative age. The two types of alteration always occupy the same relative positions; sericite adjacent to the ore-bearing vein, clay minerals always between the scricitized rock and fresh quartz monzonite, except where overlap of alteration effects between adjacent fissures has eliminated the lower grade mineralogical products, as is the case in much of Butte's Central zone of pervasive sericitization. As long as active circulation continued in the channel, each zone migrated away from the fissure, that is, it grew at its outer edge and simultaneously receded at its veinward edge because of encroachment by the next innermost zone. The different mineralogical and chemical responses within the wall rocks to the attack by the ore fluid are dependent not on a drastic about-face change of composition of the fluid in the channel relative to its ability to alter the quartz monzonite but on continuously varying conditions of physico-chemical environment within the wall rock outwardly from the vein.' Introduction From the economic viewpoint it is highly desirable that much effort be expended for the purpose of increasing our knowledge of ores and their origin. It has been the observation of the senior writer, many times expressed, that the mining companies have spent too little money in research on the geology of nature's deposits of copper, lead, and zinc, which we know to be of limited extent and which, when exhausted, must be replaced by new discoveries. Experience at Butte and elsewhere has forced the conclusion that observation and mapping in the field must be supplemented by laboratory work if we are to arrive at a reasonably correct understanding of the geology of ore bodies and their environments. It is only through the medium of such correct understanding of geology that we shall be able to accomplish the maximum toward aiding mine operations and at the same time provide a proper background for field examination work whether it be geological or geophysical. The Anaconda Copper Mining Company's answer to the need above expressed has been to equip a geological laboratory at Butte. The reason why Butte was selected is obvious, for situated there is one of the world's largest and geologically most interesting concentrations of copper and zinc. Furthermore, because of the great extent of underground workings both laterally and vertically, the opportunities for observation and study of ore occurrences probably are unequaled anywhere. The laboratory was established with five principal objectives in view. These were: 1. As an aid to Anaconda Company mine operations at Butte and elsewhere, this work to supplement that of the mine geologists. 2. To aid in acquiring as complete an understanding as possible of the behavior of Butte veins and ore bodies laterally and in depth.

Jan 1, 1949

By Charles Meyer, Reno H. Sales

AT Butte, successive zones of sericitized and argillized quartz monzonite occur around every ore-bearing fracture regardless of its size, attitude, or relative age. The two types of alteration always occupy the same relative positions; sericite adjacent to the ore-bearing vein, clay minerals always between the scricitized rock and fresh quartz monzonite, except where overlap of alteration effects between adjacent fissures has eliminated the lower grade mineralogical products, as is the case in much of Butte's Central zone of pervasive sericitization. As long as active circulation continued in the channel, each zone migrated away from the fissure, that is, it grew at its outer edge and simultaneously receded at its veinward edge because of encroachment by the next innermost zone. The different mineralogical and chemical responses within the wall rocks to the attack by the ore fluid are dependent not on a drastic about-face change of composition of the fluid in the channel relative to its ability to alter the quartz monzonite but on continuously varying conditions of physico-chemical environment within the wall rock outwardly from the vein.' Introduction From the economic viewpoint it is highly desirable that much effort be expended for the purpose of increasing our knowledge of ores and their origin. It has been the observation of the senior writer, many times expressed, that the mining companies have spent too little money in research on the geology of nature's deposits of copper, lead, and zinc, which we know to be of limited extent and which, when exhausted, must be replaced by new discoveries. Experience at Butte and elsewhere has forced the conclusion that observation and mapping in the field must be supplemented by laboratory work if we are to arrive at a reasonably correct understanding of the geology of ore bodies and their environments. It is only through the medium of such correct understanding of geology that we shall be able to accomplish the maximum toward aiding mine operations and at the same time provide a proper background for field examination work whether it be geological or geophysical. The Anaconda Copper Mining Company's answer to the need above expressed has been to equip a geological laboratory at Butte. The reason why Butte was selected is obvious, for situated there is one of the world's largest and geologically most interesting concentrations of copper and zinc. Furthermore, because of the great extent of underground workings both laterally and vertically, the opportunities for observation and study of ore occurrences probably are unequaled anywhere. The laboratory was established with five principal objectives in view. These were: 1. As an aid to Anaconda Company mine operations at Butte and elsewhere, this work to supplement that of the mine geologists. 2. To aid in acquiring as complete an understanding as possible of the behavior of Butte veins and ore bodies laterally and in depth.

Jan 1, 1949

C. Le Neve FosteR, Llandudno, Wales: I regret that Prof. Clowes is not here, and also that I cannot produce one of his lamps for inspection. The lamp has but just passed the experimental stage, and is now on sale in England for the purpose of testing it in practice. The only complaint I have heard made against it is the high price. It costs six or seven guineas. Possibly that would not frighten you on this side of the water as much as it does us. R. W. RaymonD, Brooklyn, N. Y.: So far as my obsrvations and experience go, we have not yet reached a state of affairs in the coal-mines of this country which calls for the general use of safetylamps by common miners. Certainly such a practice is to be avoided if possible, on account of the recklessness of miners, which it seems almost impossible to control by warning or discipliue. It is much better, if practicable, to confine the use of safety-lamps to inspectors or " fire-bosses," and not to permit the miners to work or to go where naked lights cannot be carried. In a colliery near Pottsville, Pa., with which I was connected for five years, and which had the reputation of being highly "fiery " (jets of fire-damp bubbled continually through the puddles in the gangways, and a thin sheet of it lay along the roof), we managed to avoid all serious

Jan 1, 1894

By Herbert H. Uhlig

ALTHOUGH the mechanical properties of high-carbon manganese-iron alloys, particularly the Hadfield manganese steels, have been established, the literature discloses discrepancies in the reported properties for the low-carbon alloys. Hadfieldlo summarized the existing data up to 1927, including the investigations of Guillet, Arnold, Strauss, Burgess and Aston, and reported his own values for alloys containing for the most part from 0.06 to 0.15 per cent carbon. He noted: From these comparisons it will be seen that while there is a broad and general agreement as to the character of the alloys at the different manganese percentages, there are disparities in individual cases, especially as regards the degree of toughness or brittleness displayed by an alloy with certain percentages and with particular types of treatment. These differences are not always readily explainable. Ib His data showed that alloys containing 4 to 10 per cent manganese water-quenched from 1000°C. were brittle and hard with maximum brittleness at about 7 per cent. Slight improvement in ductility was obtained with compositions from 10 to 17 per cent manganese. Alloys containing up to 17 per cent manganese slowly cooled rather than quenched from 870°C., he found, were slightly improved in ductility with significant improvement in alloys analyzing 4.1 and 4.8 per cent manganese. Recently Walters, Kramer and Loringa reported mechanical properties for alloys made up from electrolytic manganese and ingot iron and containing from 0.02 to 0.04 per cent carbon. They showed that a tempering treatment at 540°C. (1000°F.) for one hour significantly improved the ductility of compositions ranging from 6.7 to 20.7 per cent manganese. The differences of these compared with Hadfield&apos;s results they considered to originate in this tempering treatment plus the fact that Hadfield&apos;s alloys contained higher carbon and phosphorus (0.06 to 0.15 per cent C; 0.06 to 0.07 per cent P compared with 0.02 to 0.04 per cent C, <0.001 per cent P). In this paper it is shown that of the low- carbon alloys (0.02 to 0.03 per cent) containing from 3.3 to 21.5 per cent manganese moderately or rapidly quenched from 1000°C. some are brittle or ductile, depending on presence or absence of hydrogen. Hydrogen is readily absorbed at high temperatures, and much of it is retained when the alloys are cooled to room temperature. The presence of hydrogen in the range of composition from 10 to 18 per cent manganese is a major factor in determining relative ductility. At 22 per cent manganese, and also at compositions below 10 per cent manganese, factors other than or in addition to hydrogen play a role. These are discussed. Also data are presented to show that hydrogen absorbed by the high-carbon alloys of Hadfield composition is without effect on their mechanical properties.

Jan 1, 1944

By A. J. Griest, A. P. Young, P. D. Frost

A study was made of the effect of ß grain size on the tensile ductility of a-ß titanium alloys haet treated to strengths in the range 165,000 to 180,000 psi. It was concluded that the primary cause of $ embrittlement is the large grain size which is obtained so rapidly in many a-ß titanium alloys when heated into the ß field. It was also found that grain-boundary a and acicular intragranular a in the microstructure are not necessarily detrimental to the tensile ductility if the prior ß grain size is sufficientlv fine. BETA embrittlement occurs in a-ß alloys when the finish hot-working or stages of the subsequent heat treatment have been done at temperatures in the ß field. In order to avoid this embrittlement, for-gings must be finished at temperatures under the ß transus. For better workability, it would be desirable to forge at temperatures in the ß field. For this reason, research has been conducted to determine the cause of ß embrittlement. Although ß grain size has been considered as a possible contributing factor to ß embrittlement, only limited research has been done to evaluate its effect. The effect of addition elements on ß grain growth in unalloyed titanium has been studied by Liu.&apos; Complete mechanical property data, however, were not obtained for correlation with grain size. Ogden and coworkers2 have investigated the effect of both a and ß grain size and grain shape in Ti-Cr-Mo alloys. Their data indicated that tensile ductility was relatively insensitive to ß grain size at annealed strength levels (140,000 psi ultimate). No study has apparently been made to determine the relationship between ß grain size and ß embrittlement in a-ß alloys heat treated to high strength (180,000 psi ultimate). The high-strength condition is that in which ß embrittlement is particularly severe. Beta grain size is not easily varied through the use of a range of annealing times and temperatures in the ß field, because of the rapidity with which ß grain growth occurs. Short-time heating techniques are needed to obtain the smallest ß grains. EXPERIMENTAL PROCEDURE In this research, the experimental procedure was as follows: 1) Tensile and microimpact specimen blanks were resistance heated to produce a range of ß grain sizes. 2) The tensile and microimpact blanks were then solution-treated in the a-ß field and aged to produce predetermined ultimate tensile strengths in the range 165,000 to 180,000 psi. Tensile and impact ductility were then correlated with a grain size for constant strength levels. Materials—The alloys Ti-6A1-4V, Ti-4A1-4Mn, and Ti-16V-2.5Al are representative of the heat-treatable a-ß types in which ß embrittlement can be severe. The compositions and ß transi of the heats studied are given in Table I. The Ti-16V-2.5Al heat was melted and fabricated to 1/4 in. round at Battelle; the other alloys were obtained as 1/4 in. round rolled from commercial heats. The micro-structures of the as-rolled alloys were fine a-ß mixtures. This structure is typical of titanium alloys hot-worked extensively in the a-ß field. Resistance-Heating Treatments to Establish ß Grain Size—For direit resistance heating, a 1/4-in.-diam s~ecimen was heated with a 3000-watt transformer rated for 1000 amp with adjustable secondary voltage. The apparatus included a spray quench fixture. Both heating and quenching periods could be automatically controlled. For temperature measurements, 28-gage Chromel-Alumel wires were tack-welded to the specimen at its midpoint. A high-speed recorder-controller was used to control the heating cycle.

Jan 1, 1960

By Leon W. Dupuy

A brief elemental discussion of the fundamental factors involved in diamond drilling often fills a need, particularly when a mine operator is contemplating for the first time an exploratory drilling campaign. Mr. James A. Barr, of the Mining Methods Committee of the Institute, has suggested that many engineers must undertake a drilling program of one kid or another and, in the case of diamond drilling, sometimes even are at a loss as to how to start correspondence. The Bureau of Mines has acquired much experience in managing exploratory diamond-drilling activities. Its activities in diamond drilling included exploring for potash in Texas, Utah and New Mexico1-&apos; during the 1920&apos;s. The Strategic Minerals Exploration program was started in 1939 and was materially expanded during the war to include critical and essential minerals. At the peak of its war-time activity more than 200 engineers were employed, a majority of whom supervised diamond drilling. Many of them had little experience with such work prior to their employment with the Bureau, and it was necessary to instruct them in their duties. The purpose of this paper, therefore, is to present the fundamentals of exploratory diamond drilling from the viewpoint of management in such a way that they will Serve as a basis on which those beginning exploratory diamond drilling may build an experience and acquire ability to direct exploration as they gain that experience. Selection of Method of Drilling Selection of the method of drilling is governed by the type of material to be penetrated and by the type of sample needed to determine the quality and importance of a deposit. Types of drills that might be used for a given job include diamond drills, churn drills, hand auger drills, power auger drills, bucket drills, and rotary drills (sometimes called "seismograph rigs"). Each type has a specific field in which it is most useful. While the Bureau of Mines utilized all the types of drilling mentioned, diamond drilling was used on a majority of its exploratory projects. Factors Governing Selection of Diamond Drilling The prime consideration in selecting a method of drilling is first to determine what results are desired and then to choose a method that will furnish reliable data in the ground to be penetrated. Use of diamond drills permits recovery of a core as well as sludge at a comparatively low cost. The core provides an excellent means of studying the formation being drilled and furnishes much information that would be difficult to obtain otherwise. Diamond drills will recover a satis-

Jan 1, 1948

By Leon W. Dupuy

A brief elemental discussion of the fundamental factors involved in diamond drilling often fills a need, particularly when a mine operator is contemplating for the first time an exploratory drilling campaign. Mr. James A. Barr, of the Mining Methods Committee of the Institute, has suggested that many engineers must undertake a drilling program of one kid or another and, in the case of diamond drilling, sometimes even are at a loss as to how to start correspondence. The Bureau of Mines has acquired much experience in managing exploratory diamond-drilling activities. Its activities in diamond drilling included exploring for potash in Texas, Utah and New Mexico1-&apos; during the 1920&apos;s. The Strategic Minerals Exploration program was started in 1939 and was materially expanded during the war to include critical and essential minerals. At the peak of its war-time activity more than 200 engineers were employed, a majority of whom supervised diamond drilling. Many of them had little experience with such work prior to their employment with the Bureau, and it was necessary to instruct them in their duties. The purpose of this paper, therefore, is to present the fundamentals of exploratory diamond drilling from the viewpoint of management in such a way that they will Serve as a basis on which those beginning exploratory diamond drilling may build an experience and acquire ability to direct exploration as they gain that experience. Selection of Method of Drilling Selection of the method of drilling is governed by the type of material to be penetrated and by the type of sample needed to determine the quality and importance of a deposit. Types of drills that might be used for a given job include diamond drills, churn drills, hand auger drills, power auger drills, bucket drills, and rotary drills (sometimes called "seismograph rigs"). Each type has a specific field in which it is most useful. While the Bureau of Mines utilized all the types of drilling mentioned, diamond drilling was used on a majority of its exploratory projects. Factors Governing Selection of Diamond Drilling The prime consideration in selecting a method of drilling is first to determine what results are desired and then to choose a method that will furnish reliable data in the ground to be penetrated. Use of diamond drills permits recovery of a core as well as sludge at a comparatively low cost. The core provides an excellent means of studying the formation being drilled and furnishes much information that would be difficult to obtain otherwise. Diamond drills will recover a satis-

Jan 1, 1948

By L. K. Oliver, Marshall

The use of model studies for the development of invasion patterns for cycling is .illustrated by model studies obtained with a recently developed apparatus in the solution of actual cycling problems. Introduction Depletion of a gas reservoir by cycling under pressure maintenance may be divided into three general phases. In the first phase, injection of dry gas is used to move all possible wet gas to producing wells prior to breakthrough of appreciable quantities of dry gas into producing wells. In the second phase, injection moves additional wet gas to producing wells while moderate quantities of dry gas are being produced. The third phase consists of production without injection to deplete the commercial gas reserve which remains after the cycling operation. Thus, in the first phase, a portion of the reservoir is invaded by dry gas, and the dry gas usually displaces something less than 100 pct of the wet gas from the invaded portions of the reservoir. The second phase enlarges the invaded portion of the reservoir and, at the same time, increases recovery from that zone invaded by dry gas in the first phase of the cycling operation. The result is an early yield of a substantial quantity of the liquefiable hydrocarbons in the reservoir with a minimum of the retrograde losses which occur in some reservoirs. The overall recovery from such an operation is usually high. The summation of the paths taken by dry gas in a cycling operation can be termed an invasion pattern. The use of electrical models to predict invasion patterns has been the subject of several contributions to the literature.1-3 The results of such model studies as applied to actual cases has been discussed by Kelton4 and Miller and Lents.= Recently, an improved apparatus for conducting potentiometric model studies has been developed, as described by Lee.V he purpose of this paper is to present model studies or invasion patterns obtained with this instrument in the solution of actual cycling problems. The percentage of displacement of wet gas within the invaded portion of the reservoir in cycling, increase in recoveries of wet gas by continuing cycling after dry gas breakthrough, recoveries of wet and dry gas by production after cycling, or economic factors in cycling are beyond the scope of this paper. Discussions which follow will be limited entirely to the development of suitable invasion patterns for cycling under pressure maintenance and the use of model studies therein. Discussion OF Results In using model studies to predict invasion patterns in cycling, some factors which influence the results are the following:

Jan 1, 1948

By Marshall, L. K. Oliver

The use of model studies for the development of invasion patterns for cycling is .illustrated by model studies obtained with a recently developed apparatus in the solution of actual cycling problems. Introduction Depletion of a gas reservoir by cycling under pressure maintenance may be divided into three general phases. In the first phase, injection of dry gas is used to move all possible wet gas to producing wells prior to breakthrough of appreciable quantities of dry gas into producing wells. In the second phase, injection moves additional wet gas to producing wells while moderate quantities of dry gas are being produced. The third phase consists of production without injection to deplete the commercial gas reserve which remains after the cycling operation. Thus, in the first phase, a portion of the reservoir is invaded by dry gas, and the dry gas usually displaces something less than 100 pct of the wet gas from the invaded portions of the reservoir. The second phase enlarges the invaded portion of the reservoir and, at the same time, increases recovery from that zone invaded by dry gas in the first phase of the cycling operation. The result is an early yield of a substantial quantity of the liquefiable hydrocarbons in the reservoir with a minimum of the retrograde losses which occur in some reservoirs. The overall recovery from such an operation is usually high. The summation of the paths taken by dry gas in a cycling operation can be termed an invasion pattern. The use of electrical models to predict invasion patterns has been the subject of several contributions to the literature.1-3 The results of such model studies as applied to actual cases has been discussed by Kelton4 and Miller and Lents.= Recently, an improved apparatus for conducting potentiometric model studies has been developed, as described by Lee.V he purpose of this paper is to present model studies or invasion patterns obtained with this instrument in the solution of actual cycling problems. The percentage of displacement of wet gas within the invaded portion of the reservoir in cycling, increase in recoveries of wet gas by continuing cycling after dry gas breakthrough, recoveries of wet and dry gas by production after cycling, or economic factors in cycling are beyond the scope of this paper. Discussions which follow will be limited entirely to the development of suitable invasion patterns for cycling under pressure maintenance and the use of model studies therein. Discussion OF Results In using model studies to predict invasion patterns in cycling, some factors which influence the results are the following:

Jan 1, 1948

By J. J. Bowman, E. H. Dix

A lack of experimental data illustrating the effect of composition, particularly in respect to impurities, on the mechanical properties and corrosion resistance of aluminum-alloy die castings induced the authors and their associates to undertake a limited study of these relations. A number of commercial alloys and several experimental variations of a commercial alloy were used for the investigation. Mechanical property, growth, steam, paraffin, salt spray and atmospheric exposure tests were employed. This paper deals with the more accelerated tests and the results they have produced. It is concluded that a high-silicon alloy with all impurities except iron strictly limited to small amounts will develop an excellent resistance to corrosion and retain satisfactory mechanical properties and casting characteristics. As a direct result of this investigation an alloy of this character with superior corrosion resistance is now available commercially. In general, copper increases the strength and decreases the elongation and corrosion resistance. Tin reduces the mechanical properties and the resistance to corrosion. Iron reduces the elongation and, if excessively high, may adversely affect the tensile strength. Even excessively high iron contents do not affect the corrosion resistance, which is fortunate for the die caster as it is this element that is the most difficult to control. Nickel and zinc in limited amounts do not seem to affect the properties or corrosion resistance of at least the high-silicon alloy. Growth tests have confirmed the previous common belief that dimensional changes under either dry or wet conditions at 100" C. are too small to be of practical importance. Introduction The technical literature contains numerous papers describing die castings, their production, compositions and uses, but nearly all of these

Jan 1, 1935

By J. J. Bowman, E. H. Dix

A lack of experimental data illustrating the effect of composition, particularly in respect to impurities, on the mechanical properties and corrosion resistance of aluminum-alloy die castings induced the authors and their associates to undertake a limited study of these relations. A number of commercial alloys and several experimental variations of a commercial alloy were used for the investigation. Mechanical property, growth, steam, paraffin, salt spray and atmospheric exposure tests were employed. This paper deals with the more accelerated tests and the results they have produced. It is concluded that a high-silicon alloy with all impurities except iron strictly limited to small amounts will develop an excellent resistance to corrosion and retain satisfactory mechanical properties and casting characteristics. As a direct result of this investigation an alloy of this character with superior corrosion resistance is now available commercially. In general, copper increases the strength and decreases the elongation and corrosion resistance. Tin reduces the mechanical properties and the resistance to corrosion. Iron reduces the elongation and, if excessively high, may adversely affect the tensile strength. Even excessively high iron contents do not affect the corrosion resistance, which is fortunate for the die caster as it is this element that is the most difficult to control. Nickel and zinc in limited amounts do not seem to affect the properties or corrosion resistance of at least the high-silicon alloy. Growth tests have confirmed the previous common belief that dimensional changes under either dry or wet conditions at 100" C. are too small to be of practical importance. Introduction The technical literature contains numerous papers describing die castings, their production, compositions and uses, but nearly all of these

Jan 1, 1935

By James Marsh

INTRODUCTION Economists have long expressed suspicion of the economic theory of natural resource exhaustion, even in writing articles which have contributed to it (1). Indeed, the gap which separates the pure theory from practical management seems unusually wide. It is doubtful whether a mine manager could possibly know enough about the relevant parameters of his mine to steer it along the optimal paths described by the theorists (2). Nevertheless, enough faith in the theory remains that mine managers are suspected of being a separate breed whose behavior must be studied in special courses using specialized text-books, collections of readings, and journals (3). The implied hypothesis, that mines and natural resource firms are managed differently than other firms, is the subject of this paper. In the next section the theory is developed and analyzed. In section III, I discuss the implications of the statistical results that have been obtained. Finally, conclusions are reserved for section IV. THE MODEL A key difference between the traditional theory of natural resource production and that of other forms lies in the set of variables which ire assumed to jointly determine the quantity of output the firm will produce. Output, in the non-resource case, is assumed to be a function of k clearly definable and distinguishable inputs or factors of production, viz., y = f(xl, x2, ..., xk), (1) here

Jan 1, 1977

By Kenyon E. Richard, James H. Courtright

Thomas W. Mitcham (Strategic Minerals, Inc., Grand Junction, Colo.)—The authors have presented a significant contribution to the field of mining geology. The article is graphic, remarkably concise, and crisply original. The presentation is made on only three pages with two maps, but their Silver Bell story is entirely adequate in background, development, and conclusion. Most of their colleagues would agree that this paper reflects the high quality of the work which these unusually capable men have done in the Silver Bell area over the past few years. The Silver Bell area is one of complex tectonic structure, and time and spatial relationships are by no means apparent. Actually, most of the observations and interpretations in this paper are new to published geologic literature on the Silver Bell area. I am in agreement with these interpretations with two possible exceptions, which are discussed below. One might well define the three roughly parallel west-northwest faults, shown on the insert of Fig. 2, as the major structural elements of the area. North to south, I propose that these be named the Ragged Mountain fault, the Silver Bell fault zone, and the Waterman thrust, after the mountain ranges which are the results of these major structures. While I would agree with the authors that the northern two of these major structures are high-angle faults of the Laramide revolution, my impression is that the southern structure is a low-angle thrust of approximately Miocene age. In support of this opinion, I submit the following observations: 1) irregularity of the fault in strike; 2) scarcity of Laramide intrusives and alteration of sediments along the fault; 3) present high re- lief of the Waterman Range which indicates youth or certainly rejuvenation; and 4) existence of a series of parallel structures farther to the south which results in an outcrop pattern suggesting imbricate thrusting. The authors have stated that Laramide igneous activity began with the intrusion of alaskite. Some dacite flows appear to be conformable with Cretaceous beds, and thus my impression was that alaskite followed the intrusion and extrusion of dacite. I would be interested to learn of evidence in support of the reverse relationship suggested by the authors. Kenyon Richard and J. H. Courtright (authors&apos; reply)—The authors appreciate Mr. Mitcham&apos;s attention to this paper. The names he proposed for the major faults seem appropriate. His suggestion that the Waterman fault is a thrust may be correct because he did more work in that particular area than the authors. However, it is believed that no direct evidence of a low-angle thrust relationship has been recognized, and the authors consider that indirect evidence favors a high-angle fault interpretation. The pre-dacite flow age of the alaskite is definitely established, the authors believe, by the fact that the flows rest on an erosion surface which was carved in the dacite porphyry, an intrusive clearly younger than the alaskite, as evidenced by inclusions of alaskite occurring in dacite porphyry. No direct evidence of Cretaceous sediment-flow rock relationships was found at Silver Bell, but in the nearby Tucson mountains dacite agglomerates, megascopically similar to those at Silver Bell, overlie a basal conglomerate which in turn rests on the truncated edges of steep-dipping Cretaceous arkosic beds.

Jan 1, 1956

By S. H. Lorain, Norman L. Wimmler, S. Ricker, P. E. Oscarson, H. G. Iverson

This paper has been prepared with the principal objective of recording the results of the Bureau of Mines exploration of five major clay deposits in the Western Region. It is based mainly on data contained in unpublished Bureau of Mines reports. Acknowledgment is made to the Federal Geological Survey for its cooperative work with the Bureau of Mines, to the various State geological and mining departments, and other State and local agencies. Clay Exploration by the Bureau of Mines Much has been written and published on clays and clay deposits relating to their refractory, ceramic, and other qualities but such literature is lacking in analyses of the available alumina content of the clays and provides little indication of their possibilities as a source of alumina. With this new objective in view, a great many of the known clay deposits were reexamined and new ones discovered. The Bureau of Mines made preliminary examination of numerous areas in the western United States. Five of those most favorably indicated were systematically drilled, and in each a large amount of high-alumina clay has been found. These five major projects are Molalla and Hobart Butte, in western Oregon; Cowlitz-Castle Rock, in southwestern Washington; Ione, in California; and the Olson-Troy area in Idaho (Fig. I). Preliminary scout drilling was done in the Stockton deposit at Coeur d&apos;Alene, Idaho; the White ware deposit near Lewis-town, Mont.; and 13 areas in the Spokane or eastern Washington region, where the most favorably indicated area, known as the Excelsior, is now being drilled more systematically. Preliminary drilling was undertaken in numerous areas adjacent to the major deposits and others more remote. As a result, large additional clay possibilities were found. The Clay Deposits The clay deposits under consideration are of the sedimentary or transported types, parts of which have been altered further by the agencies of weathering, ground water, or hydrothermal action. There are extensive deposits of residual clays in northern Idaho and in eastern Washington, but they have been found to be low in the available alumina and to contain much free quartz, mica, and unaltered feldspar. To be of value, they must first be subjected to beneficiation to remove these gangue minerals. The sedimentary clays have been derived largely from the decomposition, erosion, and transportation of granites, gneisses, schists, and basalts. At Molalla, some

Jan 1, 1948