Search Documents

By Persifor Frazer

The ore property of Mr. Augustus bop is situated about one and a half miles south of the New Windsor Station of the Western Maryland Railroad and is connected with the town of New Windsor by the Liberty and New Windsor Turnpike. It is about forty miles distant from Baltimore, and about seven miles west from the county town of Westminster, and a little more northeast from the celebrated Liberty Copper Mines. (See accompanying Map I and 2.) The property comprises about 140 acres, lying principally

Jan 1, 1881

By Porter W. Shimer

The device here described has been found useful in sampling foundry-iron, and there is no reason why it should not be equally useful in sampling other metals, which are not too hard to be drilled with a breast-drill. It consists, as shown in Figs. 1 and 2, of an ordinary plumber's gas T (without bead) of about 1/2-inch in internal diameter, over the leg of which is snugly fitted a small tin cup, about If inches deep, to catch the drillings which are made by use of a breast-drill with a 1/4-inch twist bit, working through the arms of the T. The forward arm of the T is filed down to a blunt edge, over which is stretched a short piece of rubber tubing projecting a little beyond the end. The bottom of the inside of the front arm of the ? is filed down to a slope, to facilitate the passage of drillings into the tin cup. The rear arm of the T is fitted with a tin ring, projecting about 1/4-inch, for the purpose of holding in place a stiff spiral brass spring, which serves to press the sampler firmly against the metal to be drilled. The other end of the spring is supported against a shoulder of the breastdrill. The projecting rubber prevents the loss of any drillings, and also the falling of sand from above into the sampler. With ordinary care there need be no risk of getting particles of rubber into the sample. It is, of course, not possible to get a fair average sample of drillings, representing a pile of foundry-iron, by taking drillings from any one or two pieces, because of the frequently mixed character of the iron. This observation applies more particularly to the sampling of iron as it is broken and piled at the foundry, than to sampling at the works, where, if the furnace is working regularly, a few pigs may fairly represent a whole cast. By the use of this device, it is possible for a sampler to pass

Jan 1, 1901

By A. G. Taylor, H. P. Ehrlinger, U. C. Tainton

FOR the last 15 years lead has been the standard material for anodes in electrolytic zinc production and it has been generally accepted that this lead should be as free as possible from impurities. Laistl says, "Next in importance to the purity of solution is the purity of the electrodes and tank lining material. The purest lead obtainable should be used for anodes." The same conclusion is expressed by Ingalls2 and by two German investigators who say that experiments have demonstrated that the purer the lead, the greater is its resistance to corrosion during electrolysis.3 Pure lead, however, while the best material hitherto available for anodes, is not entirely free from objection. The plain lead anode gradually disintegrates under electrolysis, so that the life of an anode, say 1/4 in. thick, is frequently not more than two years. Part of the lead from the anode finds its way to the cathode, lowering the purity of the deposited zinc and decreasing the hydrogen overvoltage. The rest of the lead that comes from the disintegration of the anode goes into the manganese dioxide which is precipitated in the cells, rendering unsaleable what might otherwise be a valuable by-product. Yet a further disadvantage of plain lead anodes comes from their tendency to bend or buckle during electrolysis, as a result of intercrystalline oxidation. This makes it necessary to use a fairly aide spacing between anode and cathode to avoid short circuits, and thus leads to a higher power consurnption than would otherwise be necessary. The power consumption is also affected by the high decomposition voltage at a lead peroxide surface.

Jan 1, 1929

By Peter J. Maxworthy

INTRODUCTION There is no hard and fast rule on whether functions within a company, diversified or otherwise, should be strongly centralized or decentralized. In all diverse organizations, there are certain basic functions which remain common (or central) to each element of the business, viz: Personnel Management Cash Management Taxation Management Legal Planning Accounting Standards It would follow that each of these common factors requires some supervision at a central level to ensure that overall group objectives are met. It is true that other functions including: Industrial Relations Marketing and Distribution Production Research and Development Purchasing Management Accounting may also be common to each element of the organization. However, there is far less commonality in the degree to which these functions are central to the efficient performance and financial well-being of the business. Role of Operating Units The resources of operating centers may be viewed as a bank of funds, the nature of which can be changed from time to time, but the employment of which must provide for ongoing increases in the net worth of the total enterprise expressed in terms of market values. Operating units are required to continually review products, methods, and opportunities and to monitor avenues for incremental investment--all with a view to attaining the necessary additive net present value of future cash flows of the enterprise. Operating units should be permitted sufficient autonomy to enable the best use to be made of the skills and experience of the people it employs in order to produce a return appropriate to the value of assets employed. Role of Head Office The head office will typically comprise a specialist group--the leaner the better if one strongly adopts the decentralist approach--often acting as Service Centers but also performing a control function in the corporate sense. The head office function is a cost center. It may be instrumental in developing strategies for increasing revenues or reducing costs on a group scale, but it does not generate revenue. Every dollar spent on this function is an extra dollar to be generated by the operating centers in order to achieve an increase in corporate wealth. TREASURY MANAGEMENT Treasury management is concerned with the provision of finance, cash-flow management, and risk analysis. Each decision taken within the enterprise has a cash implication. It follows that a well-integrated central Treasury function can, in all likelihood, produce economic benefits. The degree to which the function should be centralized depends largely upon the unique nature of the operating units it is servicing. Levels of ownership, the calibre of unit operating managers, and the nature and geographic distribution of the business are all factors determining the degree to which the Treasury function is centralized. In the case of Peko-Wallsend, the Treasury Department is small, comprising four people. While divisional cash-flow management is largely decentralized, Treasury is responsible for the daily management of funds surplus to the immediate needs of operating units. Treasury also operates as central banker and provides funds to

Jan 1, 1985

By H. J. Seaman

The cost of keeping platinum ware in repair becomes such an important item in laboratories where much fusion-work is done, that a method of saving in this direction may not prove unacceptable to at least some of the members of the Institute. Some two years since I had the misfortune to puncture an almost new Bishop crucible. As an experiment I endeavored to patch it, and with such success that it is still in constant use. This may be accomplished in the following manner : The crucible and patch, which should be of stout foil, are rubbed bright with silica, or rotten-stone; a light platinum wire, welded to a corner of the patch, and the whole treated for several hours with hot concentrated hydrochloric acid; after which they are thoroughly washed with distilled water and dried. The head of an ordinary iron rivet, 4 inches by $ inches, is rounded off by hammering to somewhat the shape of the crucible. This is sunk 2 inches in a block of hard wood, and firmly wedged in place. This serves for an anvil. The hammer is an ordinary cast-iron toy, 11/2 inches long, and # inches in face, mounted on a 4 inch iron rod, 10 inches long. A gas-blowpipe is fixed in a horizontal position, and the strongest heat obtainable with it directed upon the rivet head; this soon at-

Jan 1, 1885

By N. Marusov, D. K. Lowe, J. C. Karp

This paper considers, from an engineering viewpoint, several factors involved in creating, designing and locating horizontal barriers for controlling water coning. This is an effort to consolidate new concepts with previous information so that a reasonable selection of barrier materials, dimensions and vertical position can be made. Coning theories previously developed are briefly reviewed and an effort i,s made to reduce the results of coning-theory calculations to a point where routine calculations can be made with a desk calculator. It is expected that these simplified calculations will give usable predictions of the amounts of improvement attainable with barriers of various dimensions. Apparatus and procedures used for testing the suitability of commercial cements are described and test results are presented. INTRODUCTION Just about as soon as the phenomenon of water coning was recognized as an oilfield problem, there were suggestions that the production of water coning could be controlled or completely suppressed by means of horizontal barriers. It was also suggested that natural barriers such as shale streaks were helpful in restricting bottom-water production. The implication was that wells not having the benefit of continuous shale streaks to suppress bottom waters should, in some way, be supplied with an artificial barrier. With regard to the selection of barrier materials, there are many references which give the merits of liquid barriers.',' These liquids include surface-active agents," recipitates' and emu1sions. There is no real need to review the merits of these materials again. This paper deals with the use of solid barriers which could be made from various cements. The two major restrictions placed on these barrier cements are that (1) they must be commercially available in large quantities, and (2) they must be applicable by means of standard tools and equipment with techniques that have been fully developed and are in general use at the present time. A schematic drawing of a horizontal barrier in a reservoir is shown in Fig. 1. Two maximum stable water cones are illustrated-—-one for the wellbore diameter and the other for a barrier. A maximum stable cone is one that has attained its maximum volume at the critical production rate and is on the threshold of producing water. The volume displaced by each water cone and the rise in water table are indications of the amount of water-free oil produced. Corrections for porosity, connate water and residual oil, of course, must be applied. The water-oil interface which defines a maximum stable cone is called a free surface. It is a surface over which the pressure is constant. This free surface has the shape of a limiting streamline at and below which there is no movement or transport. The shape of the water cone describes the pressure drop in the reservoir. The effect of a completely impermeable barrier on the cone shape is essentially the same as extending the wellbore out to the barrier radius. The placement of a horizontal barrier requires that a horizontal fracture be created using a single-point entry technique. Two methods may be employed for filling this fracture. One method consists of propping the fracture before filling with cement. The other consists of fracturing with fracture fluid, then immediately following with cement

By L. D. Clark

Pay-out, the ratio of capital expenditure to annual cash return can be very revealing when employed to gage the merits of a proposed mining venture. It is a quantity, numerically but not physically equal to a factor, by which cash return may be discounted to equal required investment. The fewer the pay-out years, the greater the average annual earning power of the project. Considerable material has been written in the past about the most important and difficult problem mining management faces in evaluation of a property: the optimum production rate for the venture. What daily capacity should be adopted for the proposed operation that it may be the most rewarding to those underwriting it? H.C. Hoover has said, "The most important objective is the least cost per ton mined; and minimum working costs can only be gained by the most intensive production." Theoretically and practically, the quicker the ore is removed, the more profitable should be the venture because of the saving in fixed charges, the consequent lower unit costs and the interest unearned by the profit from the unmined ore. Yet, such performance will be tempered by policy and a restraint imposed by the ratio of capital expenditure to annual cash return. * The 'Annual net profit after taxes but including depreciation and depletion allowances. former will be based upon an analysis of the economic climate anticipated, with its many ramifications including the demand for the product, prices, tax laws, the conduct of labor and related wage scales. The variables and intangibles involved in estimating the optimum production rate for a mine do not readily lend themselves to mathematical relationships or equations and the problem can become complex indeed. The more readily applicable and relatively faster appraisal method will be used which, in addition to being reasonably adequate in most cases, will serve as a guide, should a more expanded and detailed estimate be desired. The first question is what is company policy with respect to the rate of investment return? This will depend on that significant period of time referred to as the pay-out, which can be defined as the estimated interval during which capital investment is returned through application of annual cash return to its recovery. Expressed another way, it is the ratio of capital expenditure to the annual cash return. For example, if the capital investment is $C and the annual cash return is $A (after Federal tax), then $C/$A = the pay-out period in years. That is to say, if $C = $1,500,000 and $A = $214,000, then which is the mathematical expression for the period of time it takes to recover the funds originally invested in a mining enterprise. The relationship yp = $C/$A can be useful — an expression which requires only the significant tern yp to be fixed; in other words, the long range investment policy. For what is the pay-out period but an expression of that policy in terms of the speed, within practical limits, with which an individual or company may want to recover capital expenditure? A policy by which pay-out will be fixed is imperative. This ratio must lie within relatively narrow limits governed by what is economically feasible. It cannot be too low, rendering the ratio impractical or absurd, nor too great, delaying the return of capital for reinvestment beyond a commensurate interval. What pay-out will govern this policy? Federal corporate taxes would seem to present the best measure. Consider mining in Canada where new mines are exempt from Federal income tax for 3½ yr from date of first production. This exemption expressly allows The Act states: "A corporation . . . i s not required to include the profits . . . for the period of 36 months commencing with the day on which the mine came into production in reasonable commercial quantites." a company to recover capital expenditure during the early stages of production. With such an incentive, it is logical to strive for as much capital redemption as possible during this period. Thus, 3½ yr would be a major contribution to the pay-out in Canada. Furthermore, it generally takes from 1½ to 3 yr to develop

Jan 1, 1963

By R. J. Wygal, J. Naar

An equation for three-phase (water, oil, gas) imbibition oil permeability is developed, assuming the water to be the dominant wetting fluid. Oil isoperms are obtained for consolidated sandstones characterized by 1/pc2 = CS*. The evolution of an oil-gas system imbibing water from Swi to(Sw,imb )max is shown to proceed along a line of constant oil saturation with increasing oil permeability and decreasing gas saturation. When the gas satuation cannot be reduced further, the system evolves along a line of constant Sg with decreasing oil saturation and permeability. The initial gas saturation is shown to reduce markedly the effect of complete wetting by either oil or water on flow performance. INTRODUCTION Imbibition oil isoperms are required for performance prediction when a well is producing water, oil and gas. This situation occurs in multiphase displacements such as underground combustion, steam injection and the water flooding of highly depleted reservoirs. In a recent paper,1 a model was presented for the prediction of two-phase imbibition characteristics. This paper extends the imbibition model to the case of three phases by assuming that the water is the dominant wetting fluid. The following results were obtained from the model: (1) an analytical expression of oil isoperms; (2) oil isoperrns as functions of reduced water, oil and gas saturations, valid for all sandstones having a capillary pressure curve which can be approximated by 1/PC = CS*; and (3) evaluation of the three-phase flow performance as dictated by complete wetting by either oil or water. The agreement between predicted and observed oil recovery in the presence of a gas phase, reported in Ref. 1, is a partial support for the present development. However, experimental data are not available at this time to check fully the model predictions. Perhaps this paper will stimulate the collection of such data. The imbibition model of a porous medium has been described previously, and the reader is referred to the paper of Naar and Henderson1 for details. In brief, the model is formed by the random interconnection of straight capillaries, with a provision for the blocking of the non-wetting phase by the invading wetting fluid. The following expressions were derived from the model. 1. The amount of oil blocked by the invading water is

By Bruce T. Stanley

A key point in the design and operation of a modern mining operation is the construction of what is called an ore-body model or block model. This model is a representation of reality constructed from predicted information. The blocks involved are merely subsets of the overall model which allows manipulation of the contained information on a local scale. In general, block models enable mine planners to effectively select the most promising means of extracting the ore both physically and economically. The uses of a block model can be quite diversified, but one must realize that a single model that satisfies all curiosities and forms of expertise is difficult to construct.

Jan 1, 1979

INTRODUCTION AND SCOPE This chapter is intended as a brief review of the mathematics of compound interest and of the meaning of time equivalent money. In order to make valid economic evaluations of various investment alternatives, it is important that they be analyzed on an equivalent basis, taking into account the time value of money. Compound interest has been said to be one of the eighth wonders of the world. Certainly compound interest is a fact of life in today's economy. Whenever we deal with money over time-investments, earnings, savings, loans, etc.-we are immediately confronted with the principles and effects of compound interest. In such an environment it is necessary to be able to determine time value equivalence of various sums of money received or paid at different dates. It follows that all future payments or series of payments that would repay a present sum with interest at a stated rate can be said to be equivalent with each other. Equivalence, then, is a function of the interest rate. MATHEMATICS OF COMPOUND INTEREST FACTORS In order to develop mathematical formulas for various time value equivalence of compound interest we will use symbol designations: P is Present or principal sum of money; usually refers to value at time zero. F is a single sum of money at some designated future date. R is The amount of each payment in a uniform series of equal payments made at the end of each period. n is Number of interest compounding periods (may represent annual, semiannual, quarterly, or even daily periods). i is the period compound interest rate. Figure 20-1 illustrates the increase of princi-

Jan 1, 1980

By E. Luttgen

The substance referred to in the title is the artificially prepared basic carbonate of magnesia, a compound of the carbonate with the hydroxide. It is the "block-magnesia " of commerce, the magnesia alba of the pharmacist. Its composition, though somewhat indefinite, may usually be expressed by the formula : 4MgCO3,Mg(OH)2, 5H2O; it is found to vary slightly with the details of the method of preparation. This substance has been employed recently with much reported success, as a non-conductor of heat. It is moulded to form coverings suitable for steam-pipes and their fittings and sectional jackets for boilers and cylinders; it is furnished also in forms suitable for lining refrigerators, walls and roofs of buildings, fire-proof safes, etc. It was with a view of ascertaining the efficiency of this material as a non-conductor, or, rather, its relative efficiency among the various non-conducting materials in use, that the writer made the experiments about to be described. A block of magnesium carbonate or magnesia alba exhibits some interesting physical qualities. It is a smooth, white, close-grained solid, in outward appearance resembling a block of Paris plaster. It possesses the lightness of cork, the porosity of sponge, and withal a degree of firmness and strength that, in view of its levity, is quite remarkable. To examine more closely the properties of this substance, a number of 1-inch cubes were sawed from the commercial block-carbonate, also some bricks, that is, blocks measuring accurately 2 x 4 x 8 inches, the dimensions of an ordinary brick. The cubes weighed from 2.2 to 2.7 grammes, the bricks weighed 140 to 175 grammes (5 to 6 ounces). The bricks were carefully measured and weighed, and placed in vessels containing distilled water, in which they became gradually submerged, owing to the displacement by water of the air inclosed in the structure of the magnesium carbonate. After twenty-four hours the blocks were removed from the water, dried superficially by contact with filter-paper and weighed. From the increase in weight, the volume of the water absorbed, and consequently that of the air displaced by it, were obtained. For example: a block which when dry weighed 155

Jan 1, 1887

By Frank Riddle

THE life of thermocouples is governed, to a large extent, by the protection they receive when in use; particularly when the temperatures being measured are high and the products of combustion are reducing in character. Several types of protection tubes are being used for this work; they are made of ordinary and aluminous porcelain, fused quartz, carborundum, fused alumina, fireclay, and some kinds of metal. All of them may render good service under certain conditions but they must be used for the purpose for which they are intended. For example, fused-quartz tubes are very good when excessive changes in temperature occur, but under certain conditions they will crystallize and lose their strength. Porcelain is used in several ways in connection with the use of thermocouples: for insulating the two wires of the couple and to. prevent short circuits; for protecting the entire couple in a refractory gas-tight tube, which is ordinarily fastened to and is considered part of a properly equipped thermocouple; and for protecting the complete thermocouple from the possibility of physical injury and to support it. This tube is made porous and strong and is ordinarily built right into the wall or crown of the furnace, as the case may be. The insulating tubes must be small and sufficiently refractory to withstand the temperatures at which they are to be used. The length of the tubes, porosity of the material from which they are made, etc. does not particularly matter. The tubes are sometimes made with two or even four holes, the latter being used where it is desirable to have two couples as close together as possible for calibration work. The thermocouple protection tube must be of proper size to permit the thermoelements and insulating tubes to be inserted or taken out easily. It must be porous enough to withstand sudden changes in temperature and yet gas-tight, as well as refractory enough to withstand the furnace temperature, even if the tube protrudes into the furnace in a horizontal position without support for a reasonable distance. If the

Jan 9, 1919

The dictionary defines 'jargon' as "barbarous or debased language ". This description does not suffice. Quiller-Couch has said, it is "a kind of writing which, from a superficial likeness, commonly passes for prose in these days, and by lazy folk is commonly written for prose, yet actually is not prose at all ". The two main vices of jargon, he says, are "that it uses circumlocution rather than short straight speech", like the Babu who reported his mother's death by saying: "Regret to inform you, the hand that rocked the cradle has kicked the bucket ". Its other chief vice is that "it habitually chooses vague woolly abstract nouns rather than concrete ones", like the newspaper statement, "He was conveyed to his place of residence in an intoxicated condition", instead of saying, "He was carried home drunk". Jargon is "an infirmity of speech", it is not journalese, but akin to it. "Like respect- ability in Chicago, jargon stalks unchecked in our midst" and renders much technical writing ridiculous. It deals in periphrasis instead of going straight to the point, it loves the abstract rather than the concrete, it dabbles in words of sound rather than of meaning. Avoid it, despise it, if you purpose earnestly to write well. "In literature as in life he makes himself felt who not only calls a spade a spade but has the pluck to double spades and redouble." * Jargon is rampant in technical publications. Catalogues and other advertisements are conspicuous offenders, but with these the critic is not concerned, except in so far as such 'write-

Jan 1, 1931

By Ednlund D. North

Discussion of the paper of Edmund D. North, presented at the Spokane meeting, September, 1909, and published in Bulletin No. 37, January, 1910, pp. 21 to 25. A. SCOTT REID, London, Eng. (communication to the Secretary*) :-As a constructor of several glass mine-models, I have read with much interest the description of the model of the Montana-Tonopah mine-workings by Edmund D. North. As an interchange of ideas and experience is always an advantage, and in view of the fact that such models are coming more and more into vogue, perhaps the following remarks on this subject may prove of interest to mining engineers generally and to Mr. North particularly. In the model of the Waihi gold-mine, New Zealand, which I constructed, a dust-proof case is used. The top, bottom, front, and two ends are of glass; the back only is of wood, painted a dull white, against which the mine-workings show very distinctly. Each mine-level is represented by a horizontal sheet of glass, supported on metal runners fixed to the uprights at each end of the case, in a manner similar to that described by Mr. North. The corner uprights are strengthened by having a metal band screwed to the inside face of each, to which the metal runners or supports for the sheets of glass are screwed in turn. The reason for having this additional strength is that as the mine is developed in depth, and fresh levels are opened, the increasing weight of the glass sheets, added to the model, caused the unsupported wooden uprights to bend slightly, so that the glass sheets-did not fit in with the desired nicety, and co-ordination was, to a considerable extent, lost. Strengthening the uprights in this manner is not important in models of mines in which only a few levels have been opened, or when the sheets of glass are small, but in the Waihi model there are 15 sheets of glass to be supported, and more to be added as development proceeds, and the weight is considerable.

May 1, 1910

By Persifor Frazer

TILE ore property of Mr. Augustus Roop is situated about one and a half miles south of the New Windsor Station of the Western Maryland Railroad and is connected with the town of New Windsor by the Liberty and New Windsor Turnpike. It is about forty miles distant from Baltimore, and about seven miles west from the county town of Westminster, and a little more northeast from the celebrated Liberty Copper Mines. (See accompanying Maps 1 and 2.) The property comprises about 140 acres, lying principally

Jan 1, 1881

By C. P. Proctor, E. D. Hummer, J. A. Younkins

COMPARATIVELY little has been published relating practical experience with the control of the solid content of washery water systems that must be "closed." A "closed" system is one that for some reason may not be cleaned by the emission of any effluent of high solid content to be replaced by clean water in order to hold the solid content of the waste water within reasonable bounds for efficient washing. It is the purpose of this paper to describe practical experience with such a water system and to present data that it is hoped may be of some use to those who are faced with a similar problem. The washery clarification system described comprises three thickeners and three filters, and although it is admitted that each of the fields of water settling and thickening and filtration offers a wide scope for investigation, the authors are not attempting to present the answers to these problems but to set down the results of some experience along these lines, making no claims as to the ultimate solution of the problems in hand. The subject of water clarification has vast ramifications; for example, the science of flocculation as applied to water settling and filtering opens up fields of wide possibilities of which as yet little is known. A comparatively recent entry into the field of water treatment, which may offer possibilities of practical application, is the use of "wetting" agents such as "Aerosol." GENERAL ARRANGEMENT OF WATER SYSTEM So that the reader may obtain a comprehensive picture of the factors concerned in the control of a closed water system, it is necessary to give a brief description of the washing plant that is serviced by the water system to be described in the following pages. As we are not primarily concerned with the washing plant in detail, only a brief description of the flow of coal as it relates to the water system will be given here. For a more detailed account of this type of washer, the reader is referred to earlier papers.1.2 The washer, which handles 0 to 4-in. raw coal (750 tons per hour) is an American Rheolaveur plant of two complements; the coarse coal or sealed discharge plant and the fine coal or free discharge plant. The sealed discharge plant (Fig. r) consists of twin 48-in. primary launders, each having two washing boxes, supplemented by one 32-in. rewash launder, which also has two washing boxes. "Push" water for washing and conveying coal in these launders is supplied from a constant-head tank under pressure head of 10 ½ ft. at the point of introduction at the feed end of the launder. This tank also supplies water for upward or vertical currents used in the Rheolaveur or washing boxes. Each box discharges into a sealed boot elevator (Fig. I).

Jan 1, 1942

By D. U. Deere

The title of this chapter is "Indexing Rock for Machine Tunneling" or, a simplified approach to a very difficult problem. I do not think that we can divorce the considerations for conventional tunneling from that of the requirements in terms of geologic information that is necessary for machine tunneling. Experience has shown that in conventional tunneling, the rate of progress achieved in driving a tunnel and the cost involved can be almost directly related to the general rock quality and to the water conditions actually encountered. The very method selected for driving the tunnel or perhaps adapted during the construction period, that is, full-face, top-heading and bench, or multiple-drift, is largely determined by the degree of severity of the adverse geological features. The amount and type of support required to stabilize the rock behind the advancing face are also directly related to the ground conditions. The support may range from bald-headed to rock bolts placed as needed- perhaps pattern rock bolting, light steel sets, all the way to closely spaced heavy steel sets with full lagging and invert struts. At times crown bars, spiling, and breast boarding must be used to advance the face. Shotcrcte applied immediately to the arch and upper walls is a fairly recent advance in providing both temporary and permanent support. Ground-water inflows can further reduce the rate of advance, causing stability problems and reducing the overall efficiency of the mining crew. Required pumping may also be very expensive depending on the grade of the tunnel and the amount of water. And in shafts, of course, there is the pumping problem. To offset the adverse effect of the ground-water inflows, one must often resort to grouting ahead of the face. But this very operation which helps cut down the water inflow also increases greatly the time required for mining, and of course, there is additional cost involved in the actual operation. The conditions described above do not occur uniformly throughout the rock mass but rather they are concentrated

Jan 1, 1970

By L. Casagrande, C. O. Brawner, D. L. Pentz, B. Kennedy, E. Hoek, H. Q. Golder, K. Barron

H. L. HAMMERSLEY, B. C. Dept. of Mines. I would like to ask Mr. Brawner if the direction that he measured in the boreholes with the camera was referenced to magnetic north? MR. BRAWNER. Yes, it was. However, there is one problem that you may encounter if the ore body is magnetic; the borehole compass will give erroneous results. Three procedures are available to overcome this. The first one involves the use of a gyro compass instead of a magnetic compass. The second technique developed by Christiansen in Salt Lake City, is to orient the core with the use of scribing knives. The third method is to remove the compass needle and place a steel ball in the compass case. The hole must be drilled at a slight angle off the vertical. The location of the steel ball, which will roll to the underside of the hole is photographed. A borehole directional survey is then made, from which the bearing of the steel ball relative to the axis of the compass can be determined. The joint orientation is then related to this bearing at all depths. J. ROBINSON, B. C. Dept. of Mines. It was stated this morning that there have been some recent developments that give us the ability to drill horizontal drainage holes and install drainage pipes more cheaply than in the past. Would Mr. Brawner tell us some of the new developments and methods of installing these horizontal drain holes? MR. BRAWNER There are two zones in which you may be concerned about installing drains; the first is in the overburden soil, the second is in the rock. Each area requires a different installation method. If the rock is fairly massive and the holes will remain open, the simplest procedure is to use standard air track equipment or a percussion drill. At one of the mines in the Highland Valley, drains up to 300 ft. long have been installed with a percussion drill at a rate of one drain per day. The costs were in the order of $2.30 and $2.40 per foot. If the rock is quite soft, such as in a serpentine, it will be necessary to install a casing in the hole. The least expensive casing that will not deteriorate within the life required should be used. Plastic pipe or black iron pipe are commonly used. In soft rock, it may be necessary to drill with a casing to prevent the col-

Jan 1, 1971

By L. G. Truby

DISCUSSION By Rhrt G. Nisle, Phillips Petroleum Co., Barthesville, Okla. The subject paper presents the results of a reservoir behavior analyzer study of the pressure-production performance of five Ellenburger pools in West Texas. These five pools are Wheeler, TXL, Andector, Embar, and Martin. This laboratory has also made reservoir behavior analyzer studies in this area and arrived at substantially the same conclusions. Although the principal results of the studies made in this laboratory are confirmed by the results in the subject paper, there are certain points of difference. The points of difference are (1) the subject paper includes the Martin pool in the common aquifer, whereas our studies indicate that it is not, and (2) the subject paper concludes that the effective aquifer is considerably smaller than that derived from studies made in this laboratory. In terms of reservoir analyzer data, our rejection of Martin is based on the inability to obtain a satisfactory match of the pressure curve when Martin is considered as lying within the common aquifer. A satisfactory match was possible, however, when Martin was run as an isolated pool. This indicates that the pressure disturbance resulting from production at Martin had not reached Embar, Andector, TXL, or Wheeler at the time of our study. A similar situation exists relative to Dollarhide. In tern of geological data, our rejection of Martin is based on the presence of a faulted zone between Martin and Embar. This condition is indicated in Fig. 4 and again in Fig. 10 of the subject report. If a permeable connection between Martin and the other fields does exist, it is probably by way of a detour around this fault. The second point of difference between the two studies is illustrated by a comparison of Fig. 4 of the subject paper with Eg. A. Fig. A is obtained from an internal report on one of the studies made by this laboratory. It will be noted that the area indicated in Fig. 4 is roughly that marked "Pool Unit" in Fig. A. The additional portion of the aquifer shown in Fig. A was simulated on the reservoir analyzer by means of the water drive network. A satisfactory pressure match could not be obtained without this additional network. The differences involved here stem from a more fundamental consideration concerning reservoir analyzer operating techniques. The true source of these differences in reported results cannot at this time be determined because of the incompleteness of the subject paper. It is not stated, for instance, whether the pressure match was induced by altering the field resistance or the field capacitance, or both. Changing analyzer

Jan 1, 1953

By Strathmore R. B. Cooke, Robert E. Brandt

EARLIER work1,2 has shown that the strength developed by fired magnetite pellets containing silica or silicates is due to three separate effects. Two of these are associated with the formation of slag in the interior of each pellet at temperatures above 1000°C, where the atmosphere is substantially though temporarily neutral. The third is independent of the silica content and is responsible for the development of a hard shell around the pellet during the initial stages of firing, a condition which permits the pellet to assume the increasing load of the overlying burden and prevents extrusion of the slagged and semi-liquid interior. Pellets made from hematite concentrates do not show these effects unless specific additives are incorporated, and it is these differences in behavior which in large part account for the difficulty in producing satisfactory pellets from such concentrates. Elsewhere it has been stated that "the most important factor responsible for the development of strength in fired magnetite pellets containing no additive is the oxidation of magnetite to hematite and the subsequent recrystallization and grain growth of this constituent."1 The object of the investigation reported in the present paper was to study in detail the mechanism described above and to evaluate its contribution to the strength of the fired pellet compared with other possible mechanisms, excluding slag bonding. This was effected by placing together polished faces of two cubes prepared from specific minerals and then heating them under constant pressure at different temperatures both in air and in nitrogen.

Jan 4, 1954