Search Documents

By I. N. Knap

Discussion of the paper of HOWARD R. HUGHES, presented at the Now York meeting, February, 1915, and printed in Bulletin No. 99, March, 1915, pp. 629 to 635. I. N. KNAPP, Ardmore, Pa.-The claims made in the paper for the Sharp & Hughes cone bit are modest. I have used it with satisfactory results. It is a wonder for eating through hard, brittle rock; it will drill through iron pyrites that the fish-tail bit cannot enter. Soft ground is apt to contain concretions that are much harder than the containing ground. ?We have at times in drilling with a fish-tail bit thought the hole was partly in such hard material and partly in soft, thus making a difficult place to drill past in the ordinary way. By changing to a Sharp & Hughes cone bit such obstructions were easily overcome. This cone bit has greatly widened the range of work that may now be profitably accomplished by the hydraulic rotary method of drilling. It is not, however, adapted to drill soft or sticky ground, the old fish-tail bit being better for such purposes. The fish-tail bit usually scrapes its way through the material drilled, but not always. I believe at times it cuts and chips in soft friable rock. That is, the bit seems to bite into the rock, and when sufficient torsion is put on the drill stem it breaks its hold and jumps around and chips the rock from the bottom of the hole, like a stone cutter's chisel, and then takes another hold. This condition occurs only in friable material when the bit is sharp and the feed properly controlled. The Sharp & Hughes cone bit is a most valuable -tool for the rotary driller.

Jan 5, 1915

By Kenneth A. Moon

Kenneth A. Moon (U.S. Army Materials Research Agency)—The authors are to be congratulated for a very interesting and valuable paper. Their discussion of the structural implications of the results shown in their Fig. 5, however, requires a small correction. The model of Speiser and Spretnak with 0 = 1 and z' = 2 is perfectly reasonable for the Ti-O a phase, but Eq. [3] is valid only for solutions sufficiently dilute that the number of empty sites excluded by more than one filled site is negligible. The composition at which intrinsic saturation occurs therefore cannot be deduced from Eq. [3], but but must be decided by consideration of the structural details of the phase in question. In this case, intrinsic saturation is expected not at the composition Ti3O but at Ti2O, because Ti2O has the anti-Cd structurel4 for which each filled octahedral site has two nearby empty sites, one in the hexagonal plane immediately above it, and one in the similar plane below it. The other two models, with ?=1/3 and 1/2, imply a distinction between octahedral sites in pure titanium which is not easy to justify. The problem of extending Speiser's and Spretnak's treatment in a general way to more concentrated solutions will be the subject of a forthcoming publication by the writer. M. T. Hepworth and R. Schuhmann, Jr. (authors' reply)—The authors wish to thank Dr. Moon for calling to their attention the paper by Holmberg which presents the results of X-ray studies of Ti-O solutions ranging from 0 to 33 at. pct 0 and quenched from various annealing temperatures between 400" and 1800°C. Within these ranges, Holmberg found three types of phases: 1) At high oxygen contents (above 25 at. pct) and low annealing temperatures, he found the anti-Cd(OH)2 structure referred to by Dr. Moon. In this structure each titanium atom is in contact with 3 oxygens and each oxygen is in contact with 6 titaniums, the "available" oxygen sites corresponding to every other layer of octahedral sites in the titanium matrix. The limiting composition is Ti2O. However, this anti-Cd(OH)2 structure was not observed for samples containing 25 at. pct 0 or less. 2) For the specimen containing 25 at. pct 0 annealed at 400°C an ordered Ti3O structure was observed. This structure is related to the anti-Cd(OH)2 structure but differs from it by providing only two oxygens adjacent to each titanium atom and thus is consistent with the model represented by Eq. [5] in our paper, with 6 = 1/3, z' = 0. 3) For dilute solutions and for more concentrated solutions annealed at higher temperatures, the structure corresponds to that of the metal with random distribution of oxygens among all the octahedral sites. Thus, it is interesting to observe that the thermo-dynamic indications of ordering in the vicinity of Ti3O can now be supported qualitatively at least by Holmberg's X-ray evidence of the existence of an ordered phase of the composition Ti3O. That is, for solutions with oxygen contents close to that of Ti3O, both the thermodynamic data and the X-ray data are more consistent with models based on the ordered structure of Ti3O than they are with the model which Dr. Moon suggests corresponding to "intrinsic saturation" at Ti2O.

Jan 1, 1963

By Thomas Fraser, David R. Mitchell

THE primary purpose of the loading plant is to transfer the finished product from the preparation machines to the railroad car, truck, or barge in which it is to go to market. Secondary purposes of the loading plant are: to prevent excessive degradation of sizes during loading, to reduce segregation as much as possible, and to prevent excessive quantities of very good or off-grade coal from entering any one car. Nonuniformity of consignments is one of the chief sources of complaints by consumers and coal merchants. A properly designed loading plant will do much to reduce complaints and insure uniformity, not only from shipment to shipment but also in each individual consignment along the length of the car and in cross section. DEGRADATION IN STORAGE, LOADING AND SHIPMENT The object in loading is not only to handle the coal without breakage and segregation, but also to produce a well-trimmed load that will ride to its destination without spillage o~ breakage en route. The small sizes present in a car-of prepared coal as received by the purchaser consist of: missed small sizes not screened out in the preparation plant, breakage during loading, and breakage caused by handling en route. For domestic sizes of anthracite shipped from the Pennsylvania anthracite field to Atlantic coast cities, the dealers' loss because of breakage in loading and shipment amounts to from 2 to 5 per cent and for anthracite shipped to Middle West cities, the loss is 8 to 9 per cent. This difference is in part because dealers in the Middle West rescreen their coal more thoroughly than is usual in the East. One dealer handling Illinois No. 6 coal shipped from southern Illinois mines to Chicago reports an average size loss of 10 per cent when lump coal is unloaded with a fork. This runs as low as 5 per cent for carefully loaded coal and as high as 15 per cent for carelessly loaded coal. An Ohio dealer estimates the degradation in loading and shipment of West Virginia coals consigned to Ohio cities as follows: Pocahontas lump

Jan 1, 1950

By C. M. St. John

INTRODUCTION The stress redistribution accompanying the excavation of a deep tunnel may induce failure of the rock. The role of the support system is to control the extent of the failed region and hence to limit closure of the tunnel within an allowable amount. In such circumstances, the design of the support system is generally based on the Ground Reaction Curve (GRC). The GRC is the relationship between the support pressure and the induced displacement at the tunnel wall for a circular tunnel under hydrostatic loading. In the calculation of the GRC (see Brown et al. (1983) for an exhaustive list of reference), the rock is generally treated as an elastoplastic material characterized by cohesive-frictional yield strength and by dilatancy during plastic deformation. A recent analytical development (Detournay, 1983) has allowed the generalization of the GRC concept for some cases of non-hydrostatic in-situ stress fields (Detournay and Fairhurst, 1982). As an application of that development, this paper describes design charts that provide powerful means of performing parametric analysis for tunnels subject to non-hydrostatic loading. BACKGROUND The in-situ stress in a plane perpendicular to the tunnel axis can be decomposed into mean and deviatoric components, Po and So (see Fig. 1). Since it is assumed that the rock is characterized by a Mohr-Coulomb yield strength, the deviatoric invariant So must be less than the limiting value Sl0 given by

Jan 1, 1984

By T. Prof. Ph. D. Egleston

(Read at the Amenia Meeting, October, 1877.) THE copper-bearing rocks of Lake Superior are composed of a series of metamorphic rocks, comprised under the names of amygdaloid and conglomerate, in which the copper and silver found with them are pseudomorphs. These rocks, generally, have well-defined walls which cause them to separate easily. Generally, the country rock is sterile, but it occasionally rises into the copper-bearing rock, and then carries copper. Usually, the amygdaloids carry copper, and the greenstones or melaphyres which encase them do not. There is a very generally received opinion that the copper in these beds occurs in shoots. This does not appear to be proved, though the opinion seems to have some foundation from the experience of the Calumet & Hecla Mine, where a body of poor rock has been left, which, on the mine map, shows a general direction. The theory may be true of that individual mine, but too little work has been done in the other mines to draw any decided conclusion. The copper is very unequally disseminated in the rock, if any given piece be taken as an example, but, if the whole copper-bearing series be considered, its distribution is uniform. It may prove that there are certain directions in which the copper has been deposited more abundantly than in others, and these may be found to correspond with certain geological causes, but up to the present time the knowledge gained is not sufficient to warrant any general conclusion. These rocks are supplemented by a series of true fissure veins, of which there are several systems, making the amount of native copper very large. Unfortunately, except in the fissure veins, known as "mass-mines," the copper is so scattered through the rock, and is in such a fine state of division, that, although it is not always difficult to mine, it is always difficult to dress it sufficiently too make it pay. The metal is so uniformly distributed through these copper-bearing rocks that detached pieces, called " float," are found in digging on almost any land in the country. These pieces vary from very small fragments, weighing not more than a few ounces,, up to many pounds. III one instance, in making an excavation for a cellar of a

Jan 1, 1878

By F. Keller, R. H. Brown

BECAUSE of the extensive use of Alclad 24s alloy sheet in aircraft construction, there is much interest in the metallurgical changes caused by heat-treatment of this product.1,2 One of these changes is the result of the diffusion of soluble elements from the core into the coating during treatment. This paper deals with the thermal treatments that may influence diffusion and with the practical effects of diffusion on the serviceability of the product. As is well known, Alclad 24s-T sheet has a core of high-strength alloy combined with surface layers of relatively pure aluminum. The microstructure of a cross section of this product is shown by Fig. I. hot only does the relatively high-purity coating have a high resistance to corrosion, and hence serves as a mechanical barrier between the core metal and the corroding environment, but in addition this coating I exerts electrochemical protection over areas where the core may be exposed, such as cut edges. In addition, the coating affords electrochemical protection to projecting heads of *417S-T, 17S-T and 24S-T rivets, or attached members made from these alloys. Under some conditions of heat-treatment, however, diffusion of copper into the coating will alter the electrochemical relationship between the coating and the core to the extent that only partial protection will be obtained under some corrosive conditions. The reason for the electrochemical protection lies in the fact that the coating layers of pure aluminum are anodic to the alloy core. The addition of copper to aluminum produces alloys in which the potential is lower than that of the pure metal. Moreover, as the amount of copper in solid solution in z4S alloy is increased, the potential of the alloy becomes more cathodic. When heat-treated at 920°F. and quenched in cold water, 24s-T is about 0.16 volt cathodic to pure aluminum. However, copper will diffuse from the core into the coating, and if it reaches the surface the potential will be altered in a cathodic direction. Thus the potential dif-erence between the core and coating may be less than 0.16 volt, depending upon the thickness of the coating, and the time and temperature of heat-treatment. Of the methods available for determining the extent of diffusion of copper from the core into the coating of Alclad 24S-T, two are generally used; namely, the metallographic and the solution potential method.3 METALLOGRAPHIC METHODS Metallographic methods will reveal the progress of diffusion of copper into the coating. For instance, the diffusion zone in the coating intermediate between the coating surface and the core is shown in Fig. I. This photomicrograph is of a polished and etched cross section of 0.040-in. Alclad 24S-T sheet. Diffusion proceeds into the coating more rapidly along the grain boundaries than through the body of the grains. consequently, the diffusion zone is not of uniform width

Jan 1, 1944

By Stanley L. Lopata, Eric B. Kula

SEVERAL methods are available for determining pole figures by X-ray means.' The earlier film methods have been replaced by techniques in which the intensities are measured by Geiger counters on an X-ray diffractometerZm7. These methods utilize either flat transmission or reflection samples,214°8 cylindrical specimens,3 or spherical specimens.7 A single transmission or reflection sample will not yield information over the complete pole figure. The cylindrical specimens suggested by Nortod and the spherical specimen of Jetter and Borie7 have the advantage of allowing the whole pole figure to be obtained without any corrections to the intensity for absorption, There is a lower limit to the size of sheet which can be conveniently studied, however, and sample preparation can be rather tedious. Probably the most common method today for determining the complete pole figure is that developed by Schulz. A flat reflection sample is used for determining the pole figure from the center out to about 70". Because of the geometry of the system used, little or no correction for absorption or irradiated volume is necessary.4'6 A separate transmission sample is used for the region near the edge of the pole figure. This procedure requires two separate samples, one of which must be a thin carefully-prepared transmission sample. Furthermore, since the reflection and transmission data are in different arbitrary intensity units, a region of overlap must be obtained, and the intensity data from one set of measurements converted to units of the other. These are serious disadvantages of this method, and they point out the need for a simplified procedure. Since the reflection technique can be used for planes whose normals lie up to about 70° from the sample surface normal, it is apparent that a complete pole figure can be obtained by reflection alone if sample surfaces are cut at oblique angles to the rolling plane Specifically, if a rolled sample is cut so that the normal to the surface formed lies equidistant (54" 44') from the rolling plane normal, rolling direction, and transverse direction, then complete information for one quadrant of the pole figure can be obtained by reflection from the surface. Fig. 1 shows this oblique surface, as well as the position of the pole of this surface in the pole figure. When a surface has been cut oblique to the rolling plane, the standard polar stereographic net is inconvenient to use, and it would be more desirable to have the center of the net coincide with the pole of the oblique plane. Fig. 2 shows such a net, where the center has been offset 54' 44' to correspond to a specimen cut as in Fig. 1. This net was in effect obtained by rotating a standard polar stereographic net 54" 44' with the help of a Wulff net. With the experimental setup used. a sample can be cut from plate of 1/2-in. thickness or br Gen- erally thinner sheet is under investigation, and a composite specimen must be used. A convenient procedure has been to bond together, using epoxy resin, sufficient sheets to form a cube. These are clamped in a vise, and when dry, the whole vise is rotated and a flat surface ground at the required angle. The sample is then mounted inside a larger steel ring using Koldmount, the backside ground flat and parallel to the approximate desired thickness. The sample is then polished and etched to remove any effects of cold working during grinding. With this method only one quadrant of the pole figure is obtained. Often pole figures show symmetry around the rolling and transverse directions, and any slight asymmetry is due to scatter. Should the pole figure not be symmetrical, four oblique surfaces, corresponding to the four quadrants of the pole figure, would have to be examined. In most cases there is symmetry at least around the rolling direction, which reduces to two the number of quadrants to be investigated. For many purposes all that is required is an average polefigure for the four quadrants. This canreadilybe obtained with composite specimens of sheet material, where sheets Corresponding to each of the four quadrants can be intermixed. The four quadrants can be obtained by considering sheet in the normal position, and by rotatiolls of 180" around the sheet normal, the rolling direction, and the transverse direction. If desired, the whole thickness of the sheet can be used, yielding an average of the surface and interior textures; or the surface material can be removed from each sheet, resulting in a pole figure for the center alone. Eugene S. Meieran of the Massachusetts Institute of Technology has independently developed the same method. His results, adapted to a pole figure goniometer with a specimen spiraler, will be described in another publication.

Jan 1, 1962

By A. H. Underwood, M. –Ls. Trépanier

INTRODUCTION The King and Beaver mines of Asbestos Corporation Limited (ACL) were joined in 1957 to form the King-Beaver mine. In 1964, ACL purchased the Johnson's Asbestos Company. The combined underground workings are a part of the King- Beaver mine. Asbestos ore is mined at the rate of 4080 metric tons per day (mtpd) to provide 15% of the company's daily requirement in the Thetford Mines area. Figure 1 shows the location of Thetford Mines. Two shafts service the underground. No. 3 shaft, 457 m deep, is used for personnel and material transportation, downcast ventilation, and ore hoisting. No. 4 shaft, 820 m to the south, is 389 m deep. It is used for material transportation and upcast ventilation. Figure 2 shows the relative locations of the shafts and the underground workings. The ore is mined by block caving. HISTORY The orebody outcropped at surface and was first mined as an open pit. Underground mining commenced when open pit mining became impractical. Shrinkage stoping, used initially, was unsatisfactory in the highly fractured ore. Sublevel stoping improved ore recovery and safety, but did not overcome the adverse effects of the un- stable rock. Observations of the rock failures indicated that block caving would be satisfactory. This was confirmed by careful investigation and testing. A method of block caving similar to that used at the Miami Copper Company was adopted. The first block commenced production in June 1933. BLOCK CAVING General A large block of ore is undercut above pre- pared drawpoints. The ore above the undercut caves by its own weight. Caving progresses up- ward as the caved ore is drawn. A large proportion of the rock breaks up in the caving action so that it will pass through the drawpoints. Oversize blocks are broken by drilling and blasting or mudcapping. Figure 3 shows the progressive stages of block caving. In the central part of the ore zone, the vertical dimension of a block is determined by the 132 metres between production levels. When isolated ore pockets are developed, the vertical dimensions of a block depend on the extension of the ore zone above the undercut. The minimum horizontal dimension of an under- cut determines the cavability of the overlying block. When necessary, caving is assisted by drilling long horizontal holes into the block above the undercut and blasting them. This procedure speeds up or restarts caving. It will not ensure complete caving of blocks having undercuts less than 30 m wide. Orebodies suitable for block caving are highly fractured and wide enough to cave freely without excessive dilution. Undercutting must

Jan 1, 1981

Prof. Henry M Howe, New York: It is extremely probable that this efflorescence of silica is due to the liquation either of silicon or of a silicide, and the subsequent oxidation of the silicon to silica. As Mr. Fackenthal says, it is very hard to see why silicon should liquate from an iron containing so little silicon, and it seems more probable that some silicide of some volatile element has liquated, and has dissociated on reaching the air, and that the volatile element has volatilized, leaving the silicon to oxidize to silica. The volatile elements present which might thus liquate in combination with the silicon are sulphur, zinc, and lead. It is hard to see why sulphide of silicon should have liquated from an iron containing so little of either sulphur or silicon. At first, one naturally thinks that either the zinc or the lead present in this furnace might have liquated as silicide. It is true that they are both volatile at the temperature within the furnace, but then the vapor-tension* of each of them within

Jan 1, 1901

IN order that you may be expert in every phase of this art of parting, I wish to caution you upon twelve points, all necessary, so that you may know beforehand what may happen to you and what provision you must make to obtain good results. Understand that the gain derived from this art lies in carrying out the work that you wish to do accurately and with profit, which means nothing other than working with certainty and seeing that there is no loss of gold or silver [69v] or substance of anything that is valuable in itself. For, since everything lost is silver or gold, it is valuable however little. it may be, and many little things obviously make one large one; for gain increases gain, and loss, loss. Therefore, you will have as your first task to seek to have the materials that you are to use for making the aqua fortis of as perfect a nature as possible. I tell you this because the saltpeter is often weaker and of worse quality than the alum. For this reason it is necessary to make an effort to have it not only well refined and free from earthiness but also of a nature as powerful as pig [dung] saltpeter, the color of which tends strongly toward yellow. In order to work better, you also refine this again before you put it to use, as I shall tell you in its place. Likewise, see if you can get alum of the red kind that comes from the Levant or from Cartagena, for it costs less and is more powerful. Furthermore; see that you have a good number of well-formed cucurbits of properly purified glass not too large and of, equal content and size. Above all, see that they contain, no indentations, bubbles, folds, or scratches, especially, in the, body or in the bottom, because they break easily and the nature and great force of the acid pierces them by eating away, and makes a little hole. For this reason, cucurbits. are always divided into four grades; one is taken for making aqua fortis, another for drying the waters when they are laden with silver, the third for recovering the acids from the separations, and the fourth are either rejected as useless or dangerous, or are saved for recovering the whites or for some other service. Whoever wishes to practice this art well should remember to keep a large supply of cucurbits, receivers, and alembics. The third is the precaution which one must take in luting them; first, to

Jan 1, 1942

SAMUEL L. HOYT,* Minneapolis, Minn. -I was privileged to see the apparatus used by Mr. Scott, which is quite unique. It is, as the author says, a modification of the apparatus designed by Dr. Rosenhain, but it is evidently quite an; improvement. The author is to be congratulated on the fact that lie has given us, with his apparatus, a quantitative thermal analysis of these critical points. I notice the author refers to Ac3, Ac2, and Ac1. His designation of the Ac2 point is all right, but naturally in a steel with as much carbon as this, which would mean a hypereutectic steel, the other point might better be considered as an Ac, point with possibly another point above the Ac, point. Another important point brought out is the fact that, in Fig. 3, the lines representing the Ar1, transformation and the Ac,1_3 transformation do not intersect at the zero rate curve,

Jan 5, 1919

By D. H. Yardley

ENGINEERS and geologists find the magnetic compass unreliable in many mineral bearing areas because of local magnetic attraction. This is the case in the vicinity of many contact deposits, and particularly true in the Lake Superior district where iron formation is wide spread and causes wide fluctuations of the magnetic needle. One of the most useful instruments for geologic traversing or running grid and claim lines under these conditions is the dial compass which does not depend upon magnetism. Difficulties encountered in the field because of local attraction can be overcome through transit observation of Polaris or the sun, or use of the solar attachment. However, a field party often lacks the equipment or time for work of such accuracy and it is here that the dial compass finds its use.

Jan 3, 1954

By J. C. Purcupile, R. L. Morris

Present methods of roof support require that first a hole must be drilled, and then a toggle belt or grouted resin bolt be set. Automating this system is very difficult. Therefore, we decided to develop a system which would insert pins into the roof in one step. We think that this type of system can be automated much easier. It would then speed up the roof bolting operation and eliminate the need for a man to work under unsupported roof, making roof bolting a much safer job. There are two ways that a pin can be inserted in a mine roof without drilling a hole. It can either be pushed in, using a very high, constant axial force; or it can be hammered in like a nail. The former method involves very high compressive stresses in the pin, and requires complicated machinery to prevent buckling. Since hammering the pin does not require high axial forces buckling is not as likely. Also, experiments have shown that there are no problems associated with getting the pin to go in straight. We chose to develop the second method. While investigating methods for hammering a pin into a mine roof, we learned that piles were being driven 10 times faster than by conventional methods with a method called "orboresonance." We decided to turn the pile driver upside down, and drive pins up into the mine roof. Sonic Pin Setting Machine The machine consists of a steel bar supported at the nodal points of its first mode of transverse vibration (Fig. 1). A mechanical oscillator, driven by a hydraulic motor, is attached to one end of the bar. This provides the forcing function for the vibrations in the bar. The hydraulic power is supplied by a portable unit. When the forcing function is near the natural frequency of the bar, large amplitudes of vibration occur and require little power input. An anvil is attached to the bar at a point of maximum deflection, providing a means for striking the pin. Since the bar is being driven near its natural frequency, it takes little energy to accelerate the bar back and forth between each hit. This means that most of the power being put into the bar is going into driving the pin. This is unlike conventional pile drivers which use most of their power to accelerate the hammer back and forth between hits. The resonant frequency of the bar we used is about 250 Hz, which is in the audible range, hence the term "sonic pin setting machine." The system benefits are: (1) elimination of the two-step drilling and pin-setting roof bolt operation, (2) increased speed, (3) more intimate contact between the formation and bolts, (4) less expensive roof bolts, (5) higher integrity, (6) potential for automatic operation. Modifications During the months from Oct. to Dec. 12, 1974, under U.S. Bureau of Mines grant No. 00144104, "Projects on Coal Extraction," six members of the senior class at Carnegie Mellon University designed and built the experimental machine. They drove three pins into the Safety Research coal mine at Bruceton, Pa., and determined that the project was worth continuing. In January 1975 we began making modifications and repairs in preparation for a more extensive program of testing at Bruceton. The major items were: 1) Design and build a collapsible pin guide to keep the pin parallel with the line of travel of the lift table. 2) Move the anvil to the center of the bar. 3) Refinish the nodal holes and install new node pins and bushings. 4) Realign the bar in its frame. 5) Install a relief valve on the lift unit to control the upward force. The upward force that we exert on the pin is relatively small, so there is no tendency for it to buckle. This means that all we need to do is hold the pin straight during its initial penetration. This allows the bushing to travel up and down in a straight line. At the beginning of penetration, the bushing

Jan 1, 1977

US 4,194,729 - Sintering of iron oxide ore on a straight sinter belt. The upper strand of the belt is divided into sintering and cooling sections with windboxes for removing their respective gases. The main for collecting cooling gas is located beneath the lower strand and is connected to opposite sides of the windboxes, while the main for collecting sinter exhaust gas is located beneath the lower strand and connected to sinter section windboxes. Both mains are exhausted via gas-evacuating fans and pipes to a flue. Space requirements are lessened and plant accessibility can be maintained at optimum conditions. K. Wacker and F. Feigk, assigned to Dravo Corp. Mar. 25, 1980. 8 pp. (266-144). Filed: 10-30-78 (956,058). Priority: West Germany, 12-16-77 (2,756,082).

Jan 1, 1982

By C. Erb Wuensch

The Eagle mine is situated in the Kerber Creek mining district, Bonanza, Saguache County, Colo. The climate and topography of this district arc similar to those of mining camps of the Rocky Mountain region that lie 9000 to 12,000 ft. above sea level. The district is at the northeasterly edge of the San Juan volcanic region, in which successive Tertiary lavas have built up a high plateau resting upon earlier sedimentary formations, or the underlying pre-Cambrian complex. The latter was exposed in places by erosion previous to the eruptions. In the Bonanza district, proper, only volcanic formations, andesites and latites, are found. Dr. H. B. Patton,1 in his survey of the district, discriminates between several varieties of lavas and maps these as distinct flows. They are local variations within the same lava and it is impossible to determine any distinct line of demarkation between them. Structurally they are members of the same flow. There are three general types of vein occurrences: 1. Lead-zinc-copper-silver-gold veins in well-defined fissures with a quartz gangue; ill these, the various sulfides show a zonal arrangement. 2. Massive gray copper ores high in silver, in irregular fractures in the form of small lenses and pockets, in which little or no quartz is found. 3. Manganiferous quartz veins very low in silver and gold at the surface which, with depth, become important silver veins containing subordinate amounts of gold. These veins have a quartz gangue with an abundance of Phodochrosite. The silver is associated with small amounts of sphalerite, galena, and pyrite; fluorite also is present. The Eagle is the only mine that has been developed in the manganiferous quartz type of vein. It was discovered ill the fall of 1582, but little more than assessment work was done on the property for a number of

Jan 1, 1923

By C. Erb Wuensch

The Eagle mine is situated in the Kerber Creek mining district, Bonanza, Saguache County, Colo. The climate and topography of this district arc similar to those of mining camps of the Rocky Mountain region that lie 9000 to 12,000 ft. above sea level. The district is at the northeasterly edge of the San Juan volcanic region, in which successive Tertiary lavas have built up a high plateau resting upon earlier sedimentary formations, or the underlying pre-Cambrian complex. The latter was exposed in places by erosion previous to the eruptions. In the Bonanza district, proper, only volcanic formations, andesites and latites, are found. Dr. H. B. Patton,1 in his survey of the district, discriminates between several varieties of lavas and maps these as distinct flows. They are local variations within the same lava and it is impossible to determine any distinct line of demarkation between them. Structurally they are members of the same flow. There are three general types of vein occurrences: 1. Lead-zinc-copper-silver-gold veins in well-defined fissures with a quartz gangue; ill these, the various sulfides show a zonal arrangement. 2. Massive gray copper ores high in silver, in irregular fractures in the form of small lenses and pockets, in which little or no quartz is found. 3. Manganiferous quartz veins very low in silver and gold at the surface which, with depth, become important silver veins containing subordinate amounts of gold. These veins have a quartz gangue with an abundance of Phodochrosite. The silver is associated with small amounts of sphalerite, galena, and pyrite; fluorite also is present. The Eagle is the only mine that has been developed in the manganiferous quartz type of vein. It was discovered ill the fall of 1582, but little more than assessment work was done on the property for a number of

Jan 1, 1923

At its meeting on February 21, 1933, the Board of Directors passed the following resolution defining and expressing the policy of the Institute with respect to official participation or action in controversial matters: WHEREAS, the Board of Directors at its last meeting passed the following resolution : "The Board of Directors, having been appealed to by several Local Sections for advice concerning the attitude and policy of the Institute relating to the endorsement of candidates for public office, the following statement of policy is formulated: "Whereas, the American Institute of Miming and Metallurgical Engineers is organized for purely professional and scientific purposes, and whereas diversity of opinion among its members on partisan or political questions is inevitable, it is the ex- pressed policy of the Institute to refrain from official participation or action in political and semi-political matters."

Jan 1, 1946

By Emory Kemler

The problem of determining the most desirable operating conditions of an oil-well pumping unit, the selection of the proper material and size of sucker rods, and the design of the pumping unit, requires that the sucker-rod loads be known with a reasonable degree of accuracy. In production practice, it is also desirable to know the effects of operating speeds and strokes on a plunger motion, as well as on the rod loads. For a particular well, data on rod loads can be obtained by measuring the load in sucker rods with a dynamometer. This method is not satisfactory because it does not permit the various factors to be investigated independently. It is also impossible to measure the plunger motion simultancously with rod motion under operating conditions. The mathematical solution is impractical because of the simplifications that have to be made to get a solution and the tremendous amount of numerical work that is necessary after such a simplified solution has been attained. This paper shows how analogies and models can be applied to the solution of these problems. The loads set up in a sucker-rod string during the ordinary pumping cycle are made up of the weight of the rods, force required to accelerate the rods, weight of the oil and force required to accelerate the oil on the upstroke, rod friction, stuffing-box friction, plunger friction, friction of the oil in the tubing and rods, arid friction loss through the valves. The problem of determining the sucker-rod load is further complicated by the fact that the long oil column and the sucker-rod column act as springs, which affect the transmission of the polished-rod motion. A further complication is the fact that the motion cannot be transmitted at a speed greater than that of the velocity of sound in the material, and this means that there will be a time lag in the transmission in the motion, as well as a modification of its magnitude and a phase displacement.

Jan 1, 1936

By Emory Kemler

The problem of determining the most desirable operating conditions of an oil-well pumping unit, the selection of the proper material and size of sucker rods, and the design of the pumping unit, requires that the sucker-rod loads be known with a reasonable degree of accuracy. In production practice, it is also desirable to know the effects of operating speeds and strokes on a plunger motion, as well as on the rod loads. For a particular well, data on rod loads can be obtained by measuring the load in sucker rods with a dynamometer. This method is not satisfactory because it does not permit the various factors to be investigated independently. It is also impossible to measure the plunger motion simultancously with rod motion under operating conditions. The mathematical solution is impractical because of the simplifications that have to be made to get a solution and the tremendous amount of numerical work that is necessary after such a simplified solution has been attained. This paper shows how analogies and models can be applied to the solution of these problems. The loads set up in a sucker-rod string during the ordinary pumping cycle are made up of the weight of the rods, force required to accelerate the rods, weight of the oil and force required to accelerate the oil on the upstroke, rod friction, stuffing-box friction, plunger friction, friction of the oil in the tubing and rods, arid friction loss through the valves. The problem of determining the sucker-rod load is further complicated by the fact that the long oil column and the sucker-rod column act as springs, which affect the transmission of the polished-rod motion. A further complication is the fact that the motion cannot be transmitted at a speed greater than that of the velocity of sound in the material, and this means that there will be a time lag in the transmission in the motion, as well as a modification of its magnitude and a phase displacement.

Jan 1, 1936

By Joseph Kuti

ROOF SUPPORT DEVELOPMENTS IN LONGWALL (1) European longwall mining technology developed towards its modern form in relatively deep mines. With increasing depth the stability of openings driven for ventilation, travel or transport becomes paramount in mine design considerations. As a result the number of roadways and entries, as well as their width must be a minimum. (1) Another important aspect of European mining is the high density of mineable seams, as opposed to the wide lateral extension of a single seam in the U. S. A. Multi-seam mining requires strict planning and near 100% extraction, since with increasing depth, the effect of remnant pillars can be devastating. As a result the face layout of a modern European longwall panel is based on single panel entries of moderate width and great height. The mode of extraction is generally a mixture of the advance and retreat system which is called a 2-system. It is obvious, therefore, that the supports developed for the entries and for the intersection areas are more complex than those in the U. S. A.

Jan 1, 1981