Search Documents

By Bunting S. Crocker

DISCUSSION Fred C. Bond (Allis-Chalmers Manufacturing Co., Milwaukee)—This is a very complete description of the screened ore fine grinding installation at Lake Shore. The only important data which might be desired are the operating screen analyses and power consumption in each stage. The statement that the energy consumption, or kw-hr per ton, remains constant for all mill diameters is of great interest, but the opinion is widely held that the kw-hr per ton decreases as the mill diameter increases. More definite test work is needed to establish this point. Screened ore fine minding has been successful on hard Lake Shore ore &d on about equally hard South African Rand ore. However, it is still not determined whether it would be successful on ores of average or less than average hardness. It is possible that with softer ores the consumption of ore pebbles might be exceedingly high, or might even exceed the available supply. Also, the softer feed might result in a rapid buildup of harmful intermediate sizes in the mill circuit. These factors can be determined only by a full scale or long pilot mill test. In any case the Lake Shore staff is to be congratulated for this pioneering work. Bunting. S. Crocker (author's reply)—As requested, the operating screen analyses and Bower consumption for each of the four stages of pebble milling are given, see Table XII. The fist three stages are in series circuit; the last stage is in closed circuit. The primary circuit had rock feed averaging 124 g per piece and the final stages rock feed weighing 63 g. The intermediate stages had mixtures of the two. Regarding Mr. Bond's statement that "the opinion is widely held that the kw-hr per ton decreases as the mill diameter increases," I would say that I have frequently been told this but have never yet been shown any evidence or seen any evidence published that would prove this statement. It may be true that some of the big mills recently installed have mechanical power savers such as micarta bearings and better lubrication, but as far as the power consumed inside the mill is concerned, we at Lake Shore think that it varies as D2 .", and that is all. We published extensive information on this point in our 1939 paper. Recently Mr. Banks at Consolidated published the figures on his 10 ft 8 in. x 12 ft 0 in. rod mill. As reported in this discussion by the writer: we calculated the power necessary to run this mill based on our 7x6-ft rod mill to within 1 pct of the actual power reported by Mr.

Jan 1, 1953

By Bunting S. Crocker

DISCUSSION Fred C. Bond (Allis-Chalmers Manufacturing Co., Milwaukee)—This is a very complete description of the screened ore fine grinding installation at Lake Shore. The only important data which might be desired are the operating screen analyses and power consumption in each stage. The statement that the energy consumption, or kw-hr per ton, remains constant for all mill diameters is of great interest, but the opinion is widely held that the kw-hr per ton decreases as the mill diameter increases. More definite test work is needed to establish this point. Screened ore fine minding has been successful on hard Lake Shore ore &d on about equally hard South African Rand ore. However, it is still not determined whether it would be successful on ores of average or less than average hardness. It is possible that with softer ores the consumption of ore pebbles might be exceedingly high, or might even exceed the available supply. Also, the softer feed might result in a rapid buildup of harmful intermediate sizes in the mill circuit. These factors can be determined only by a full scale or long pilot mill test. In any case the Lake Shore staff is to be congratulated for this pioneering work. Bunting. S. Crocker (author's reply)—As requested, the operating screen analyses and Bower consumption for each of the four stages of pebble milling are given, see Table XII. The fist three stages are in series circuit; the last stage is in closed circuit. The primary circuit had rock feed averaging 124 g per piece and the final stages rock feed weighing 63 g. The intermediate stages had mixtures of the two. Regarding Mr. Bond's statement that "the opinion is widely held that the kw-hr per ton decreases as the mill diameter increases," I would say that I have frequently been told this but have never yet been shown any evidence or seen any evidence published that would prove this statement. It may be true that some of the big mills recently installed have mechanical power savers such as micarta bearings and better lubrication, but as far as the power consumed inside the mill is concerned, we at Lake Shore think that it varies as D2 .", and that is all. We published extensive information on this point in our 1939 paper. Recently Mr. Banks at Consolidated published the figures on his 10 ft 8 in. x 12 ft 0 in. rod mill. As reported in this discussion by the writer: we calculated the power necessary to run this mill based on our 7x6-ft rod mill to within 1 pct of the actual power reported by Mr.

Jan 1, 1953

By James Terry Duce

In order to facilitate interpretation of the data in this chapter, we print the following excerpts from circulars to authors, compiled by Mr. Frank A. Herald when he was Vice-chairman for Production of the Petroleum Division: Generally in Table 1 the unit for presentation of data is a field. For our purposes a field is defined as the whole of a surface area wherein productive locations are continuous. Such unit commonly includes and surrounds nonproductive areas. Such unit commonly includes a great variety of geologic conditions-—several units of continuous productive reservoirs of distinctly different structure and of distinctly dzerent stratigraphy. Therefore it is hoped that our authors will subdivide "field" so as to enable students to make analyses that may have scientific and/or commercial value. As to each space in the tabulation, it is either (1) not applicable, (2) the proper entry is not determinable, (3) the proper entry is determinable, but not determinable from data available to the author, (4) the proper entry is determinable by the author. In spaces not applicable, the author will please draw horizontal lines; in spaces where the proper entries are not determinable, the author will please insert x; in spaces where the proper entries are determinable but not determinable from data available to the author, the author will please insert y; in spaces where the proper entries are determinable by the author he will, of course, make such entries. Generally, y implies a hope that in some future year a definite figure will be available. Inability to determine precisely the correct entry for a particular space should not lead the author to insert merely y. Contributions of great value may be made by the author in many cases where entries are not subject to precise determination. In such cases the author should use his good judgment and make the best entry possible under the circumstances. For many spaces, the correct entries represent the opinion of the author (for example, "Area Proved") and in such cases the entries need not be hedged to such extent as in cases where the quantities are definite yet can be ascertained only approximately by the author. In cases under definite headings but where figures are only approximate, the author may use 2. For example, if the total production of a field is known to be between 1,800,000 and 1,850,000, the author may report l,8x,xxx; or if the production is between 1,850,000 and 1,900,000, the author may report 1,9xx,xxx. Where a numeral is immediately to the left of x or y, such numeral represents the nearest known number in that position. As to quantity of gas produced from many fields the question will arise as to whether the figures should include merely the gas marketed or should include also estimates of gas used in operations and gas wasted. Although rough approximations

Jan 1, 1937

By David A. Wracher

A geologist may produce for himself a surprisingly accurate photo base map and stereo coverage at low cost without the use of expensive equipment and complex photogrammetry. If care is taken and the program well thought out, good results can be expected. The only equipment necessary in this method is a small format (small negative size) camera, a few rolls of film and the appropriate filters. A light aircraft, with an opening in the bottom, is preferable so that the pictures can be taken vertically and from inside - the aircraft. The method will produce high resolution prints at large scales in the range of 1: 1200 to 1:7200.

Jan 11, 1973

By L. A. Geoffrion, R. H. Perkins, J. C. Biery

Densities of cerium metal and several lour-melting binary cerium alloys were measured over the range 25° to 800°C. A rolumeter, using NaK as working fluid, was used to obtain the data. The cerium, Ce-Co, Ce-Ni, and Ce-Cu alloys all exhibited an increase in density on melting, while a Ce-Mn alloy expanded on melting. FOR the proper design of a nuclear reactor, the change in density of the fuel with temperature must be known. This is especially important in a system utilizing molten fuel, such as LAMPRE (Los Alamos Molten Plutonium Reactor Experiment), since a relatively large change in density usually occurs during the solid-liquid transition. The fuel for LAMPRE is a Pu-2.5 wt pct Fe alloy with a melting temperature of 410°C. However, limitations in reactor design with this fuel have led to consideration of other plutonium-containing alloys for use in future generations of this type of reactor. Several ternary alloys containing plutonium and cerium as two components have satisfactorily low melting points. The system that at the present time appears to be most acceptable is Pu-Ce-Co; it exhibits little change in melting temperature with wide variation in plutonium concentration. Other alloys that have received some consideration contain nickel, copper, and manganese as the third constituent. The proposed fuel alloys are difficult to handle experimentally in the 25" to 800°C temperature range since they oxidize readily, react with many solvents, and contain a poisonous fissionable material. In addition, in this temperature range the alloys pass through the solid-liquid transition. Several techniques are available for measuring the densities and volume coefficients of expansion of solids or liquids. However, the only apparatus that appears suitable for measuring expansion coefficients over this temperature range and through the phase transition is a volumeter. In a volumeter, the indicating medium must be essentially inert to and insoluble in the material being studied. It must also possess a low vapor pressure over the operating temperature range, and its coefficient of expansion must be accurately known. One material that is satisfactory in nearly all of these respects is the alloy Na-78 wt pct K, which melts at -10°C and has a vapor pressure of 860 mm Hg at 800°C. This relatively high vapor pressure at 800°C requires an overpressure of an inert gas to prevent boiling. While a volumeter is capable of determining accurately the volume coefficients of expansion of materials, it cannot be used for absolute density measurements. Therefore, a density determination at a known temperature must be coupled with the volumeter measurements to give all the desired data. The weight-loss technique using immersion in bromobenzene at room temperature proved to be satisfactory. The preliminary work that was done on this experimental program involved developing and calibrating the equipment, and measuring the densities and volume coefficients of expansion of cerium and some low-melting binary cerium alloys. The complications that are caused with the introduction of plutonium into the system were avoided until the equipment was proved to be satisfactory and until experience was gained in its operation. It is this first phase of the experimental work that is described in this report. DESCRIPTION OF EQUIPMENT AND OPERATING PROCEDURE The NaK volumeter is shown schematically in Fig. 1. Basically, the equipment consists of two weld-sealed stainless-steel containers of nearly identical volume. One container holds a tantalum crucible and the specimen being measured; the other contains a tantalum crucible and a tantalum specimen used as a control reference material. To avoid temperature gradients, the bombs are located in a copper block inside the furnace. Stainless-steel capillaries of equal length and volume connect each stainless-steel container to a glass viewing capillary. The stainless-steel containers, stainless-steel capillaries, and a portion of the glass capillaries are filled with NaK (22 wt pct Na-78 wt pct K). The NaK/gas interface in the glass capillary is viewed with a cathetometer which is accurate to *0.5 mm. The cathetometer readings are used to calculate the volume changes of the samples during a run. This volumeter is basically the same as that described by F. Knight in Plutonium 1960. 2 However, changes in equipment design and operating procedure were made to eliminate some major operating difficulties. These changes are summarized below. 1) In filling the manometer with NaK, gas was frequently entrained in the system. Evacuation of the system before filling failed to eliminate the en-

Jan 1, 1965

By D. Beregekoff

In the routine examination of a wide variety of metal specimens it is sometimes necessary to have special methods of polishing in order to retain and reveal certain details in each specimen. Among such special cases is the retention of graphite in malleable and gray cast irons, the preservation of all types of nonmetallic inclusions in both hard and soft steels, obtaining a scratch-free surface with soft metals, and avoiding the usual relief effects with very hard specimens such as tool metals con-taining various carbide and nitride phases. It is the purpose of this paper to give an account of some of these special polishing methods in use at the Union Carbide and Carbon Research Laboratories. The polishing procedures outlined have been found to give uniform results. It is obvious that only general rules and the most important working details can be given here. Following these rules, the polisher can obtain satisfactory results if he possesses the necessary patience and has a sincere desire to give as nearly perfect a finish as possible to his work.

Jan 1, 1939

The primary purpose of the Institute is to advance the technologic and engineering arts embraced by it through interchange of knowledge. This can best be clone by the presentation and discussion of technical papers by its members. Short practical papers are especially welcome. An author should always satisfy himself that his material is of a quality that will he a credit to him and to the Institute. The preparation of a good paper frequently leads to a reorientation of the author's thoughts, and publication contributes much to the professional standing of the author. Members are urged to submit papers presenting the results of their work. Attention to the following suggestions will greatly further the prompt and efficient handling of manuscripts. 1. SUBJECTS: The subject must be within the field of the Institute. Original work, the results of field, plant, laboratory or theoretical investigations, new views on old but important problems and occasionally reviews of timely and important subjects of wide interest to our members may constitute the basis of a paper. The mere fact that the work is original does not necessarily justify publication: it must be of a substantial nature, of value to a reasonable number of our members and worthy of permanent record. It is seldom desirable to subdivide the results of a single research for publication in a variety of journals. Previous publication is usually a bar to acceptance. If any part of your paper has been published elsewhere and you regard repetition as absolutely necessary please so state in your covering letter. 2. CONSTRUCTION: Papers should be clearly and concisely written in good English. Care in this regard ensures wider reading and the saving in space permits the Institute to publish more papers. It is the experience of the Papers and Publications Committee that most papers can he improved by condensation. "Readers" who are asked to recommend acceptance or nonacceptance put particular emphasis on the length of the paper and the elimination of unnecessary or any extraneous material. The terminology and units employed should be those current in the particular field. An examination of Institute publications will afford useful guidance in such matters. Webster's New International Dictionary, 1935 edition, is the Institute's authority for spelling and style. Various abbreviations are used habitually; for instance, lb., pound; bbl., barrel or barrels; ft., foot or feet; hr., hour or hours; in., inch or inches; Fig. 1 but Figs. 2 and 3.

Jan 1, 1946

By T. D. Mueller, F. C. Miller, Jr. Earlougher R. C.

In analyzing pressure buildup tests for field wells producing both oil and gas, the common practice is to use a modification of single-phase flow theory. Validity of such an approximation has been demonstrated for single-well solution-gas-drive systems. This paper indicates that such approximations are also valid for two-well solution-gas'-drive systems. From this it is inferred that the technique can be used for multiple-well systems. A computer was used to simulate the behavior of a two-well solution-gas-drive reservoir to test the validity of the above type of analysis. Simulation results indicate that pressure buildup tests in such a system can be analyzed within engineering accuracy for formation permeability and pressure. A rule of thumb is given for estimating the length of time a well must be shut in for the pressure in a nearby producing well to increase significantly. To observe such an increase, the shut-in well would have to be left shut in much longer than normal. INTRODUCTION An important technique for obtaining data concerning a producing petroleum reservoir is the pressure buildup test. Such a test, when properly conducted and analyzed, provides information on the average reservoir pressure and the permeability in the major drainage area of a well. The theory upon which the analysis of a pressure buildup test is based assumes that the behavior of the fluid in the reservoir is adequately described by the diffusivity equation.1 Use of the diffusivity equation implies that a single fluid of small and constant compressibility is flowing. To analyze a pressure buildup test in situations which involve more than one fluid phase, the single-fluid analysis is extended. This paper verifies the extension of pressure buildup analyses to two-phase, two-well systems. Miller, Dyes and Hutchinson1 have presented a technique for analyzing pressure buildup tests in circular bounded reservoirs. Their method requires that the reservoir be producing at pseudo-steady state (constant pressure gradients) prior to shut-in. An alternate reservoir model, presented by Horner,2 assumes that the reservoir is infinite. The Homer model does not assume a Pseudo-steady state prior to shut-in, but the assumption that the reservoir is infinite implies that the average pressure can be determined only if the total production prior to shut-in is small compared to the total fluid originally present. Limitations imposed by the pseudo-steady state and infinite reservoir assumptions are avoided by the technique proposed by Matthews, Brons and Hazebroek.3 Their method can be used to calculate both the Permeability and the average pressure in bounded single-well systems which are not necessarily at steady state. They also suggested determining the average pressure of a multi-well reservoir producing from pseudo-steady state by volumetrically averaging the static pressures of the individual wells. Matthews and Lefkovits4 used numerical simulation techniques to verify that this method does produce adequate results for single-phase, multiple-well systems. Perrine5 proposed modifications to the single-phase theory so that pressure buildup tests in multiple-phase systems could be analyzed. He suggested replacing the single-phase mobility (k/µ) by the sum of the mobilities of the individual phases, and replacing the fluid compressibility by an average compressibility weighted by the saturations of the separate phases. By using numerical techniques to solve the two-phase flow problem for a single-well system, he concluded that this approximation gives results within engineering accuracy. More recently, Weller6 has shown that, for a gas-oil system with a single well at the center of a circular reservoir, pressure buildup tests can be analyzed adequately by using the modification proposed by Perrine. Feller's results also indicate that, as the gas saturation increases, this analysis becomes less accurate. To date, no evidence is available to show that the Perrine approximations can be combined with the Matthews-Brons-Hazebroek technique to calculate the average pressure of a multi-well,

By R. Raring, W. J. Harris, J. A. Rinebolt

G. W. Geil (National Bureau of Standards, Washington, D. C.)—The authors state that the degree of accuracy realized in the experimental determination of a, is likely rather low. This inaccuracy is attributed to the difficulty in reading the load of the tension machine at the instant of fracture of the test bars. I believe there is another factor which may have added considerably to the inaccuracy in the determination of a,, namely, the determination of 8,. Fracture of a cylindrical tensile specimen of a ductile metal tested in tension at room temperature is generally initiated at the axis and rapidly propagates radially to the periphery of the necked section. During the propagation of the fracture, the metal at the rim of the minimum cross-section extends longitudinally and contracts radially. Thus values of 81, based on diameter measurements made after complete fracture of the specimens do not necessarily represent the strain at the initial fracture." Data obtained at the National Bureau of Standards with a 0.3 pct C steel in the condition as-quenched from 1575°F and tempered at 1000°F for 1 hr and tested in tension at room temperature indicated a considerable "rim effect" and as shown in Fig. 13, resulted in an apparent increase in Sf from 0.90 to 0.98. As the fracture strain of this steel is approximately equal to those of the steels reported by the authors, it seems probable that a similar "rim effect" may have added to the inaccuracies in the reported values of Si and accompanying values of El. R. Raring (authors' reply)—The authors are grateful to Mr. Geil for having called attention to a possible source of uncertainty in the determination of fracture stress, and they are in agreement with the principles upon which his discussion is based.

Jan 1, 1952

By H. L. James

This paper presents the results and analysis of field trials of various magnetic instruments over anomalies ranging from 20 to 5000 gammas of vertical intensity. The following instruments were used: Askania vertical magnetometer, Wolfson vertical magnetometer (model M-I), Hotchkiss Superdips (used both parallel to and normal to the magnetic meridian, with several settings of the "sigma" angle), Lake Superior dip needle, and the dipping circle for measurements of inclination. The change in inclination over the measured anomalies ranged up to 4"; this caused pronounced changes in sensitivity of the Hotchkiss Superdip oriented parallel to the magnetic meridian. The variable sensitivity not only gives apparent displacement of crests of anomalies, particularly at high sensitivities, but also makes the data difficult or impossible to use in preparation of iso-anomaly maps. This weakness in field performance of the Superdip is shown to be eliminated by orienting the instrument normal to the magnetic meridian and measuring vertical intensity only, which in the latitude of upper Michigan is equal to 97 pct of the total intensity. The dip needle is seen to be relatively ineffectual for location of anomalies of less than 400 gammas. Introduction The U.S- Geological Survey, in cooperation with the Geological Survey Division of Michigan Department of Conservation, has for the past three years been engaged in a restudy of the Iron River-Crystal Falls iron mining district of upper Michigan. The bedrock in a large part of this area is covered with glacial deposits as much as 500-ft thick, and, inasmuch as some of the rocks have moderate to high magnetic permeability, extensive magnetic mapping has been done to assist in unraveling the complicated structure of the area. Several types of instruments have been used, and the major purpose of this paper is to present comparative data on the field performances of some of these instruments so as to aid others who face similar problems elsewhere to evaluate and choose the instruments best suited for the work. The paper is directed primarily to geologists and engineers rather than to geophysicists, although some familiarity with the instruments is presumed. The geology of the area consists of a complexly folded series of weakly metamorphosed sedimentary rocks, including the iron formation, which rests on older greenstones. Although the iron formation itself is only locally magnetic, some of the beds stratigraphically above the iron formation are rather strongly so. By tracing these hanging wall magnetic anomalies valuable information is obtained from which the structure and distribution of the iron formation can be inferred. Critical anomalies range from 25 to 6000 gammas of vertical intensity. Many anomalies can be traced in part with the common dip needle, but detection of others requires more sensitive instruments.

Jan 1, 1949

By H. L. James

This paper presents the results and analysis of field trials of various magnetic instruments over anomalies ranging from 20 to 5000 gammas of vertical intensity. The following instruments were used: Askania vertical magnetometer, Wolfson vertical magnetometer (model M-I), Hotchkiss Superdips (used both parallel to and normal to the magnetic meridian, with several settings of the "sigma" angle), Lake Superior dip needle, and the dipping circle for measurements of inclination. The change in inclination over the measured anomalies ranged up to 4"; this caused pronounced changes in sensitivity of the Hotchkiss Superdip oriented parallel to the magnetic meridian. The variable sensitivity not only gives apparent displacement of crests of anomalies, particularly at high sensitivities, but also makes the data difficult or impossible to use in preparation of iso-anomaly maps. This weakness in field performance of the Superdip is shown to be eliminated by orienting the instrument normal to the magnetic meridian and measuring vertical intensity only, which in the latitude of upper Michigan is equal to 97 pct of the total intensity. The dip needle is seen to be relatively ineffectual for location of anomalies of less than 400 gammas. Introduction The U.S- Geological Survey, in cooperation with the Geological Survey Division of Michigan Department of Conservation, has for the past three years been engaged in a restudy of the Iron River-Crystal Falls iron mining district of upper Michigan. The bedrock in a large part of this area is covered with glacial deposits as much as 500-ft thick, and, inasmuch as some of the rocks have moderate to high magnetic permeability, extensive magnetic mapping has been done to assist in unraveling the complicated structure of the area. Several types of instruments have been used, and the major purpose of this paper is to present comparative data on the field performances of some of these instruments so as to aid others who face similar problems elsewhere to evaluate and choose the instruments best suited for the work. The paper is directed primarily to geologists and engineers rather than to geophysicists, although some familiarity with the instruments is presumed. The geology of the area consists of a complexly folded series of weakly metamorphosed sedimentary rocks, including the iron formation, which rests on older greenstones. Although the iron formation itself is only locally magnetic, some of the beds stratigraphically above the iron formation are rather strongly so. By tracing these hanging wall magnetic anomalies valuable information is obtained from which the structure and distribution of the iron formation can be inferred. Critical anomalies range from 25 to 6000 gammas of vertical intensity. Many anomalies can be traced in part with the common dip needle, but detection of others requires more sensitive instruments.

Jan 1, 1949

By Raymond Sanford

IT IS difficult to know just when a hoisting rope should be removed from service and a new one substituted. It is desirable to utilize the full life of a rope but, on .the other hand, the damage and possible loss of life, resulting from delay in replacing it may amount to many times the cost of a new rope. In the present methods of inspection the inspector must rely upon accumulated experience and a certain sixth sense or intuition in addition to any rules that may be laid down regarding the number and distribu-tion of broken wires. This condition does not neces-sarily arise from lack of interest among users or makers of rope, but is due rather to the lack of satisfactory or adequate methods for testing ropes to determine their exact condition. The main difficulty in devising a physical test lies in the fact that a number of causes, all operating in different ways, contribute to the deterioration of a rope in service, and affect not only the external conditions but also the inner structure of the material of which the rope is constructed. Wear and broken wires on the outer part of the rope are not difficult to detect, but a test is needed which will clearly indicate the presence of broken wires in the interior portions and the change in strength due to alterations in the structure and properties of the material itself.

Jan 7, 1923

By Joseph E. Pogue

THAT the domestic consumption of gasoline displays a marked seasonal variation, with a low in the winter and a high in the summer, is well known. It is logical to expect that the nature of the variation has itself been undergoing a change as a result of improvement in roads, general employment of closed cars; and growth of mass haulage; but so far as I am aware the change in seasonal variation has never been investigated and measured. It is the purpose of this paper to present the method and results of such an investigation undertaken as a contribution to the technique of planning operating schedules now so prominent in connection with the functioning of the industry under a Federal quota system. For the method employed I am in-debted to the suggestions and help of Frederick R. Macaulay', who kindly looked over the work sheets; and credit is due Barnabas Bryan, Jr., for assisting in the computations and the graphic work. Ideas for the approach to the problem were also derived from an article by Aryness Joy, and Woodulief Thomas of the Division of Research and Statistics of the Federal Reserve Board*-.

Jan 1, 1934

As a service to its readers, MINING ENGINEERING is publishing the mineral industry portion of the 1952 list of "Accredited Undergraduate Engineering Curricula in the United States." This list, revised annually, is issued by the Education Committee of the Engineers Council for Professional Development, and covers all phases of engineering education. The AIME is actively represented on ECPD, which was jointly organized by the Founder Societies and various other groups interested in the professional recognition of engineers.

Jan 4, 1953

By Harrison Souder

THE object of this paper is to bring to. the notice of engineers a safety detonating fuse by the use of which misfires in blasting may be eliminated and safety in blasting operations promoted. This new detonator is a French invention and is known as Cordeau detonant or detonating fuse and is sold under the name of Cordeau-Bickford. It consists of a lead tube 5 to 6 mm. in diameter, filled with trinitro-toluene. While applicable to all classes of mining it will appeal especially to those who have to do with deep-hole blasting in open-cut clines or quarries, or any operations where a large number of holes are to be shot at one time. Since the introduction of the deep-hole blasting in the Cornwall iron mines, much trouble has been experienced from misfires and many experiments were made to determine the best and safest method of blasting. Before the introduction of the detonating fuse it was found that to insure the best results, two or more high-power electric exploders, not less than No. 6, with specially insulated conductors, should be placed in each hole; the holes wired in parallel, and for a large number of holes the current to be supplied by a live wire to the bus or lead wires at about the middle of the bench. The voltage in general use is 110 to 220, but as our material is a magnetic iron ore and the holes are generally damp, we found it advisable to reduce this to about 30 volts to prevent short circuits. A No. 7 or No. 8 special insulated detonator was adopted. But with the best of care and attention to the minutest detail, we were not able to eliminate occasional misfires and the consequent ever present danger of accidents.

Jan 10, 1914

By M. D. Cooper

FOr the purpose of obtaining some first-hand data in regard to the shooting clown of coal in bituminous 'nines, it was the writer's good fortune to be employed as a shot-firer for almost one year. In all, 6,020 shots were fired by him during this period. All of the work was clone in what is known as the South Main section of the No. 2 Mine of the Ellsworth Collieries Co., Ellsworth, Pa., a subsidiary of the Lackawanna Steel Co. Position of Shot-firing in the Cycle of Operations The established practice of the Ellsworth Collieries Co. calls first for the undercutting of the coal by electric chain machines across the face of the entry or room. This is followed by replacing any posts removed by the machine-runners, or the setting of new posts or timber, as may be required. After this has been done the machine cuttings are loaded into cars. Then the coal is spragged, and a shot hole drilled to the depth of the undercut. Next in order, the shot-firer loads the hole and fires the charge. The working place is then cleaned up, timbered if necessary, the sides and face squared up, and loose material taken down. The face is again ready to be undercut.

Jan 1, 1917

Pumping coal to market may help Appalachian coal operators increase their share of the eastern seaboard fuel business. Transporting it by pipeline is already an accomplished fact, but until recently it had to be dewatered to be used in boiler furnaces. The campaign for these eastern markets was begun in earnest last November by the widely publicized announcement of successful plant-scale firing of a central station boiler with coal slurry pumped to the burners. This latest advance makes coal similar to oil and gas in convenience in handling and controlling at the consumption end of the pipeline. Slurry could be considered a new commodity for the fuel market. HUGE POTENTIAL MARKET The heaviest concentration of power plants in the U.S. is along the line Washington, Baltimore, Philadelphia, New York and Boston which makes this region the best hunting ground for selling pipelined coal brought from western Pennsylvania and northern West Virginia. Furthermore, if this region is assumed to consume 125 million tons of coal annually, on a comparable basis, the consumption of oil and gas would be about 180 million tons. Even if all of this fuel is not consumed in central stations, it is still a very big market for coal at the right price. Consolidation Coal Co. and Texas Eastern Transmission Co. are trying to line up customers in this area so that a pipeline can be built. This is not to say that there are not many other areas in the U.S. that could not be supplied advantageously by a mine-to-market pipeline.

Jan 1, 1962

By H. J. Rose

Graphic methods have long been used to advantage in dealing with diverse phases of fuel technology and research. Not only are graphs convenient for presenting data and making calculations, but they are invaluable for deriving generalizations from a mass of data. This is particularly true when relationships are obscure and numerical correlation is poor. This paper describes a new form of graph, the Multibasic Coal Chart, which has been developed to facilitate the study and comparison of coals of all ranks from peat to anthracite on any moisture and purity basis. This type of chart is of unique value for coal classification purposes, since it permits a direct visual comparison of the results obtained when coals are classified by the various systems which have been proposed. Coals are highly variable in character as a result of wide differenees in original vegetal ingredients, degree of metamorphism, and nature and amount of associated impurities. For nearly 100 years, attempts have been made to devise a satisfactory method of classification, and many tables, formulas, ratios and graphs have been suggested. Many of the suggested systems possess considerable merit and have found a limited use, thus promoting a better understanding of coal. However, objections have been raised against each system, and none has received general adoption. When the various systems of classification are compared, it is found that there is an apparently almost hopeless confusion due to: 1. Serious lack of agreement as to the proper moisture and purity basis on which to classify coal. More than ten different bases have been proposed, each of which requires complete recalculat.ion of the analysis data used. 2. Lack of agreement as to what chemical and physical properties are most important and best to use for classification purposes. There is too little knowledge of the degree to which these properties can be correlated.

Jan 1, 1930

By H. D. Keiser

Minor industrial minerals included in this chapter are: the alum minerals, bromine, calcium chloride, epsomite and other natural magnesium salts, iodine, meerschaum, quartz, industrial crystals other than quartz, and nonfuel gases (air, helium, carbon dioxide). Alum Minerals The natural alums comprise a group of hydrated double sulfates, the most important of which are potash alum, KAI(S04)2.12H20, the "alum" of popular usage; ammonium alum, (NH4)AI(SO4)2, known mineralogically as tschermigite; and soda alum, NaAI(SO4)2.12H20. Kalinite, KAI(SO4)2.11H20, and mendozite, NaAl(SO4)2, 11H20, are fibrous monoclinic alums, distinct from the isometric species potash alum and soda alum.4 Alunite, KAI3(S04)2(OH)6, also known as alumstone or alum rock, has been used as a raw material in the manufacture of alum since early times. All the natural alums are highly soluble and occur as surface evaporation products in arid regions or in sheltered places. Potash alum, together with the other natural alums, commonly occurs as an efflorescence or crevice filling in argillaceous rocks and brown coals that contain disseminated pyrite or marcasite. The mineral is derived by the action of sulfuric acid, formed during the weathering of the sulfide, upon alkali-rich aluminum silicates. Ammonia alum is found chiefly in lignite or broad-coal beds and bituminous shales. Alunite is most commonly associated with acid volcanic rocks, where the rock has been largely altered and alunite formed owing to the presence of sulfuric acid solutions or vapors. Aluminum sulfate, which for most uses is the essential ingredient of alum, may be found in saline residues resulting from the evaporation of natural water and may be formed by the action of acid waters upon aluminous rocks. A deposit of natural potash alum occurs in an irregular network of veins associated with sulfur in rhyolite in Esmeralda County, Nevada, about 35 miles west of Tonopah and 10 miles north of Silver Peak. Alum was recovered at a plant operated on the property between 1920 and 1923 by crushing the ore to ¾ in., grinding to minus 80-mesh, and counter-current leaching; the resulting alum solution was then filtered and crystallized. Alunite was of much interest during World War I as a source of potash and during World War II as a source of alumina. The wellknown deposits at Tolfa, Italy, are veins in trachyte and have been the basis of alum manufacture there since the middle of the fifteenth century. Pure alunite is insoluble in water and in common acids, but if it is heated to 500°C it loses its water of hydration, and the residue consists largely of anhydrous potash alum, part of which is readily soluble in water or acids. If the heat is increased beyond 500°C, most of the sulfur combined with the alumina is released as oxides and the residue consists of potassium sulfate and alumina. Thus, either potash alum (and aluminum sulfate) or potassium sulfate and alumina may be made. In the

Jan 1, 1960

By Dr. O’Neil Thomas J., Donald W. Gentry

"There are two characters to the value of mining properties-one mine may have a value, owing to its real intrinsic worth; an- other (having no intrinsic value) may have a value by being so situated as to harass the working of the really valuable mine-in mining camps one is looked upon as much of ligitimate enterprise as the other.'' -Victor Clement to Simeon Reed, Wardner, Jan. 11, 1890, Reed Mss. APPROACHES TO VALUATION Value and costs are two terms basic to financial analysis which cause, perhaps, the greatest amount of misunderstanding in mine valuation studies. When discussing the value of an asset or the costs of producing a product, it is absolutely essential that the speaker define the terms being used. There are many types of value and many categories of costs. Without specific accompanying definitions, value and cost data are not very meaningful. Value refers to a measure of the desirability of ownership of property. Some of the types of value which might be encountered in a mine valuation study are: 1) Market value 2) Full cash value 3) Salvage value 4) Replacement value 5) Capitalized value 6) Book value 7) Assessed value 8) Insured value Each of these has a specific meaning which can be applied to determine a monetary amount in a specific situation. The major item of interest here is the broader question of "what is the value of the mine?" or "what is the mine worth?" In this case, we are speaking of market value. Market value is the value (price) established in a public market by ex- changes between a willing buyer and a willing seller when neither is under duress to complete the transaction. Market value fluctuates with the degree of willingness of the buyer and seller and with the conditions of the sale. The use of the term market suggests the idea of barter. When numerous sales occur on a market, the

Jan 1, 1984