Search Documents

By C. S. Matthews, P. Hazebroek, H. Rainbow

It ha been suggested that lormation fractures created by well stimulation treatments will adversely affect sweep-out efficrency in injection operations. Fluid-flow model studies involving vertical fractures of various lengths and fluid systems of various mobility ratios have been carried out to study this subject. In addition, limited data have been obtained on one model containing a horizontal fracture. It was found that relatively long and highly conductive fractures (not generally obtained fracturing operations) were required to affect the sweep-out efficiency substantially. In a given case in the field an approximate distinction can be made between the presence of long conductive fractures and shorter or less conductive ones. This is done with pressure build-up analyses along with data on the relationship of fracture length and conductivity to well productivity. This type analysis shows that usually the fractures induced are either short or of limited conductivity and therefore do not damage sweep-out efficiency. INTRODUCTION Improved well productivity and in-jectivity can frequently be exploited in injection operations. Higher total throughput can yield improved economics. On occasion, the achievement of an increased productivity or injectivity in specific wells can bring about a more uniform sweep of the reservoir. Higher rates can be exploited particularly in water floods of "depleted" reservoirs where a rapid "fill-up" is desired and where low pressures contribute to low well productivity. The creation of fractures local to the wellbore is an excellent means for achieving these objectives. Even though fracturing has been employed in some floods with success,1"3 there still seems to be some reluctance to employ this tool for fear of undue damage to the flood pattern and ultimate recovery. We therefore need to examine the influence which fractures of varying length may have on flood performance and then determine the length of fractures which obtain in the field with conventional fracture treatments. A substantial influence of fractures on the recovery obtained at breakthrough of the injected fluid has been presented by Crawford and Collins for equal fluid mobilities for the line-drive pattern.4,5 In addition, the influence which a fracture has on the production performance after breakthrough and on the ultimate recovery warrants consideration in reaching a conclusion concerning the use of induced fractures in flooding operations. This report presents this type of data for the five-spot injection pattern for several fluid mobilities. In arriving at some conclusion concerning the fracture lengths obtained in field operations we must examine the performance characteristic most affected by the fracture. This is the change in the flow system as reflected in the change in productivity and pressure build-up behavior. A study of these changes is also presented in this report. RESERVOIR ANALOGS The X-ray shadowgraph technique, employing miscible displacement in porous models, has been used in the study of the influence of fractures on pattern sweep-out efficiency. The X-ray shadowgraph procedure is described in detail in an earlier report8. Fractures were represented by leaving the proper portion of the model surface exposed to either injection or production. This assumes the fracture resistance to be negligible compared to that of the formation. Actually the flow resistance in propped fractures obtained in the field is sometimes not negligible so that the results with this model indicate the maximum influence of the fracture. Two types of models were necessary to represent vertical fractures in a five-spot flood. These pattern elements are illustrated in Fig. 1. In studying the influence of the horizontal fracture, only one well spacing length to thickness ratio of 50 was used. The pool unit of a Carter Electric Analyzer was used in studying the influence of fractures on productivity and build-up behavior. The square drainage system of a well was represented by a network of 576 elements of equal volume and resistance. One-fourth of this drainage area was studied as a model unit using a network of 144 condensers and resistors. Vertical fractures were represented by a shunt directed from the well perpendicular to the drainage boundary. Horizontal fractures were represented by a circular shunt. Resistance of a shunt was varied in representing different conductivities for the fractures. FRACTURE DIRECTION AND LENGTH The direction at which a vertical fracture extends into the formation and its length and conductivity influence the sweep behavior. The two

By R. A. Bloom, John Birtalan

CONSIDERABLE interest has been shown in recent years toward determining the crystal structure, mode of formation, and chemical composition of the x phase, designated as such by Andrews,' who was the first to establish its presence in Fe-Cr- Ni-Mo alloys . Later work2 by the same author has shown that the occurrence of x depends on the presence of some molybdenum in the alloy. The phase, which appears to be identical or very similar to a manganese, has a body-centered-cubic structure and is closely related to s phase. Koh observed a similarity in composition between x and s and speculated as to whether x might be an ordered structure of u which is known to have a tetragonal crystal

Jan 1, 1957

By A. E. Wells

In this paper are described various comparative tests made on cracked and straight run gasolines. The results of these tests may be briefly summarized as follows: Samples of 54 to 55° Bé. gravity cracked gasolines, with end point of about 442° F., and with a somewhat larger proportion of the less volatile fractions than conformable to government specifications, were used in a single cylinder variable compression engine under the same conditions as were samples of straight run gasoline of 58 to 59° Bé. gravity, and of which one had a greater proportion of the more volatile fractions than called for in government specifications. The cracked gasolines showed decidedly less tendency to knock, hence could be used at higher compression ratios and thereby developed from 10 to 20 per cent. more power than did the straight run gasolines. These figures may be taken as one measure of the superiority of the cracked gasolines under test with the straight run gasolines. It is not claimed that all cracked gasolines are superior to all straight run gasolines to the extent indicated by the above tests; cracked gasolines vary as do the straight run products. Cross's work and that of others have indicated that certain cracked products may have a much greater superiority over straight run than that determined above. From various sources and by different methods of testing data are being obtained to show the definite and generally quite considerable superiority, as an anti-Cetonating fuel of cracked gasolines over straight run gasolines. It is now becoming generally recognized that by increasing the production of cracked gasoline motor fuel from those heavier petroleum fractions, which otherwise would be used for burning purposes, the petroleum industry is not only working in the interest of the conservation of the world's supply of petroleum, but is at the same time making available to the gasoline-consuming public a product distinctly superior to the straight run gasolines.

Jan 1, 1927

By R. S. Dean

THE numerous theories of hardening which have been advanced in recent years are all satisfactory in accounting for some of the phenomena observed in hardening metals, but none so far presented account for all of the facts observed. Some years ago one of the authors, R. S. Dean,1 presented a theory to account for some of the properties accompanying work hardening. The present paper develops this theory further in the light of recent experimental, work and extends it to other forms of hardening. Many of the ideas included have come from the writings and personally communicated thoughts of others. We have attempted to give proper credit in every case, but it is possible that we have not always done so. As an historical basis it is desirable here to review very briefly the hardening theories which have been current. The first comprehensive theory of work-hardening phenomena was due to Sir George Beilby.2 He contributed the idea that with cold work part of the structure of the metal was rendered amorphous and that it was to this amorphous material that the cold-worked metal owed its difference in properties. According to Beilby's theory this amorphous material was a super-cooled liquid and, therefore, had the characteristics of a vitreous material. That such a theory is not capable of explaining the property changes in metals has been repeatedly pointed out. This theory also allowed a slip to take place only once on a given plane, which, as has been pointed out by Jeffries and Archer,3 is not consistent with the observed length of an individual slip and the amount of elongation which can be obtained by wire drawing. The modifications, which have been proposed to this hypothesis to make it coincide with the experimental facts, have to a considerable extent robbed the theory of its clean-cut characteristics. The commonest of these modifications replaces the amorphous phase with an

Jan 1, 1927

By Sam F. Harrison

The National Board of Boiler and Pressure Vessel Inspectors again sends out this recommendation: If you have an air compressor that is mounted directly on the air tank, get it off. Characteristically, small- to intermediate-sized air receivers are thin-walled vessels, and as such are prone to failure when subjected to external loading. Many of these vessels, if not a great majority, are bought by a distributor of air compressor systems, who provides the compressor, motor, switchgear and other accoutrements-all of which are very frequently mounted on a base which is then welded to the shell of the receiver. These welds at the points of attachment transmit external loading to the tank in the form of weight and vibration, frequently resulting in stress-induced cracks.

Jan 3, 1978

By P. F. Kinyoun

MANY interesting new features are embodied in the latest extension to the open-hearth department of the Bethlehem Steel Co., at Lackawanna, N. Y. Automatic control of the important factors in furnace operation-fuel, air, draft, pressure, slag composition, and of the temperature in various regions of the furnace-has been carried out to a remarkable degree; the human factor is minimized, and the chances for mishaps and irregularities in operation are greatly reduced.

Jan 1, 1937

Charles T. Malcolmson, Chicago, Ill.:—Mr. Blauvelt's admirable paper is a valuable contribution to the literature on briquetting of coal in this country. It should have a special significance for those interested in the commercial development of the coal-briquette industry. I believe that the data included in Mr. Blauvelt's paper will be particularly useful because they represent costs taken from a briquette-plant in actual operation. There are several points touched on in Mr. Blauvelt's paper which may bear comment in the way of emphasis rather than of criticism. In the first place, he has stated a fact which becomes axiomatic to any one who has had any experience in the design, building, or operation of coal-briquette plants, and that is, that the press is only one factor in the successful opera-

Jan 1, 1911

Recent start-up of a new 3450 t/d (3800 stpd) copper-zinc concentrator complex in northern Manitoba, Canada, is expected to open new reserves and dramatically cut transportation costs for Hudson Bay Mining and Smelting Co.'s Snow Lake operations. The new $C33-million mill is located in Stall Lake, Manitoba, and includes a new crushing and grinding facility and two flotation circuits for the production of 23-25% copper and 55% zinc concentrates. A small amount of lead concentrate will also be recovered. The plant will produce some 145 000 t/y (160,000 stpy) of concentrates, to be shipped by rail to the firm's Flin Flon copper smelter and zinc refinery complex, located 177 km (110 miles) to the west on the Saskatchewan-Manitoba border.

Jan 9, 1979

By L. A. Adorjan

The tensile strength of agglomerate models due to capillary forces has been determined by computation of the exact surface profiles. Graphs showing tensile strength as a function of moisture content and contact angle me given for spheres in cubic arrangement. Another model of cones attached to cube faces, in cubic packing, provides a better representation of angular particle agglomerates. An algebraic formula approximating tensile strength as dependent on surface tension, particle size, moisture content, contact and cone angles was developed. The phenomenon of "capillary evaporation" due to high negative capillary pressures is explained and its influence on tensile strength of agglomerates is evaluated.

Jan 1, 1977

By G. P. White, J. M. Jones

Introduction Computer simulation is a technique that has been around for many years. Its applications include designing steel mills, planning space shots, or even developing ways to beat the casinos in Las Vegas. However, the use of computer simulation in surface coal mining is fairly recent. To promote its use, several government agencies, including the US Bureau of Mines, Forest Service, and Department of Energy, contracted with universities and private companies to develop computer simulation programs for surface coal mining. Some of these developers include McDonnell-Douglas Electronics Co., Pennsylvania State University, Montana State University, Fluor Mining and

Jan 1, 1985

According to published reports, controlled production from the Masjid-i-Sulaiman and Haft Kel fields for the year 1934 was as follows: No new development of major importance in either of these areas is reported. Owing to the increasing- demand in North Iran, particularly for gasoline and kerosene, it has been arranged that this market shall in future draw its supplies from a newly constructed refinery at Kennan-shah. This refinery is connected by a 3-in. pipe line, 145 miles long, with the Naft-i-Shah field, on the borders of Iraq and Iran. The crude oil will pass through a topping plant at the field and the products will be stored and pumped to the Kermanshah refinery in such proportions and quantities as are demanded by actual market requirements.

Jan 1, 1935

Application of Kutter's Formula to Gases Discussion of paper by F.-ERNEST BRACKETT, presented at the Pittsburgh Meeting and issued, as Pamphlet No. 1578-A-F, with MINING AND METALLURGY, June. 1926. C. S. WITHERELL, New York, N. Y..(written discussion).-There is no reason to doubt that the relationship between the rate of, flow and. the impelling force of all fluids can be expressed by a general typical equation that takes cognizance of all relevant factors such as density, viscosity (or its reciprocal, mobility) and nature of channel-walls. Most fluids that are commonly conveyed by flow in confined channels are so highly mobile that they may be considered non-viscous, hence for these fluids the factor of viscosity does not need to appear in the equation. Water is the outstanding example of this class of fluids and its dynamic behavior has been so thoroughly investigated that proven formulas pertaining thereto, be they rational or empirical, would naturally serve as prototypes for the other non-viscous fluids. As non-viscous fluids can be classed all gases and vapors, most unsaturated aqueous solutions, gasoline, alcohol, etc. Viscous fluids comprise those that have a sluggish flow such as most oils, tar, molasses, etc., the' high viscosity of which is due to shearing resistance between molecules, a force that must betaken into account in figuring the flow of fluids of this class.

Jan 10, 1926

By D. R. Shoemaker

BACKGROUND AND PROJECT DESCRIPTION A 16.5 kt per day underground molybdenum mine is being developed at Questa in northern New Mexico by Molycorp, Inc., a wholly-owned subsidiary of Union Oil Company of California. Small scale underground mining first began in 1920 and large scale open-pit mining was initiated in 1965, but because of the high stripping ratio, surface mining is being phased out. Construction of the underground mine began in 1979, and first production is scheduled for 1983. Full production of 9 Gg of molybdenum per year will be reached in 1984. Access to the mine will be through a service shaft, development shaft, and a conveyor decline. 'The service shaft, 7.3 m in diameter and 396 m deep, will be used for personnel, supplies, development muck, and fresh air intake. It will be equipped with a large, double-deck man and material cage. A double-drum hoist will be used for cage hoisting and will handle up to a 27-t load in balance with a counterweight. Development muck will be loaded into skips in balance and a single-drum auxiliary hoist will provide secondary access. The 396-m-deep, 4.3-m-diameter development shaft will be used for initial mine development, mine exhaust air, and a slick line pass for concrete entering the mine. The development shaft is located 400 m north of the service shaft. Run-of-mine ore will be transported from one of two 1.4-kt storage pockets by a 1.2-m-wide conveyor belt located in the 10°, 1980-m-long, 5.0-m-wide, and 4.6-m-high decline. The decline conveyor belt has a centerline length of 2229 m and a vertical rise of 363 m. It will be powered by four 448 kw motors driving a single drive pulley. There will be two 1.2 m transfer belts on the surface with centerline lengths of 322 m and 542 m. All three conveyor belts will be reinforced with steel cables. On the surface, in addition to the headframes and hoist houses for the two vertical shafts, a large maintenance shop, warehouse, compressor house, change house, main office building and timber framing building have been constructed.

Jan 1, 1981

By J. F. Nicholas

THE angles between the crystallographic planes in cubic metals were originally given by Bozorth and have been republished many times. Recently, Salkovitz2 tabulated the angles for the hexagonal metals (magnesium, zinc, and cadmium). he most commonly used metal which does not fail into either of these groups is tin, which has a tetragonal structure with an axial ratio of c/a = 0.54558 (99.99 pct purity, 25°C).² ccordingly, Table I has been prepared giving the possible values for the angle, 4, between planes of the types {HKL) and {hkl). The formula used was: Hh + Kk + LI — cos? = —--------------—-----------— A [(H2 + K2 + L2-a2c2(h2 + k2 + r;)] All angles are given correct to the nearest minute as this is sufficient for all practical purposes. Every angle depends in a different way on variations in the value of c/a, but even in the worst cases a variation of about 0.0003 in this ratio is needed to vary an angle by l', which corresponds to a temperature change of 20 °C or can be caused by impurities.

Jan 1, 1952

By P. S. Kotva

Dislocation substructures in superalloy matrices of varyzng co)npositions have been studied. In general, it has been found that the alloys can be classified into ''high", ''medium", and "low" stacking fault energy classes based on the type of dislocation substructure observed in the matrix and that the substructure can be correlated to the stacking fault energy. The effect of different types of dislocation substructure and dislocation reactions on the intragranulur precipitation of carbide phases has been studied. In a Ni-Cv-Mo-Fe matrix, precipitation of MC carbides in association with stacking faults has been observed. In most superalloys, solid-solution strengthening and precipitation hardening are the chief mechanisms employed to achieve strength. The latter contribution to strength is usually achieved by the precipitation of / in certain wrought alloys. Insufficient attention has been given to the problem of obtaining strength in su-peralloys by controlling precipitation of carbides on imperfections within the matrix. The present work was undertaken to investigate the dislocation substructure in various superalloy matrices, to study the effect of such substructure on subsequent precipitation of carbides in the matrix, and to investigate whether certain modes of precipitation of carbide phases found in austenitic stainless steels2"4'6 would occur in nickel-base alloy matrices with dislocation substructures of the same type as those found in austenitic steels. 1) EXPERIMENTAL TECHNIQUES Five-pound heats of the various alloy compositions reported here were vacuum-cast. The ingots were given light deformation by rolling to break up the as-cast structure and then homogenized for 24 hr. HASTELLOY alloy X (nominal composition: Ni-2OCr-17Fe-8Mo-0.05C) was homogenized at 2150°F and In-cone1 625 (nominal composition: Ni-20Cr-5Fe-8Mo-3.5Cb-0.05C) was homogenized at 2280°F. Fabrication of 0.004-in. sheet was achieved by cold rolling with intermediate annealing treatments being carried out at the same temperature as those used for homogeniza-tion. Each solution anneal was followed by quenching. The aim of this procedure was to redissolve as much of the primary carbide phase as possible. Samples of the 0.004-in. sheet were cut and encapsulated in quartz capsules and then heat-treated in the tube furnaces. Thin foils were prepared using an ethanol-10 pct perchloric acid bath at 32°F and at a voltage of 22 v. A "window" technique was employed. Observations were made on a JEM-7 electron microscope operating at 100 kv. 2) EXPERIMENTAL RESULTS a) Types of Dislocation Substructure. Fig. 1 shows a schematic correlation between stacking fault energy, SFE, and the type of dislocation substructure observed in various matrices of nickel- and cobalt-base alloys. A precise quantitative determination of stacking fault energy is not implied in the figure but the correlation between stacking fault energy and the type of dislocation substructure obtained allows alloys to be divided into three classes in analogy with the classification employed by Swann and ~uttin~' for binary alloys of copper. Class I alloys are associated with a "high" SFE and show a cellular substructure of dislocations as typified by the micrograph of a thin foil of pure nickel deformed 4 pct at room temperature in Fig. 2. With decreasing SFE the tendency toward cell formation is lessened and dislocations tend to be arranged in coplanar groupings. Examples of this class of alloys with "medium" SFE are provided by the mi-crostructure of solution-heat-treated, quenched, and deformed thin foils of HASTELLOY alloy X, "Waspaloy" (prior to any aging), and Inconel 625. Fig. 3 shows a thin-foil micrograph of an alloy of Inconel 625 composition, solution-heat-treated, quenched, and deformed 5 pct at room temperatures. No evidence of any cell structure can be obtained in materials of "medium" stacking fault energy, Fig. 3, even after severe deformation. The stacking fault energy of the alloy shown in Fig. 3 is, however, not low enough to make the dissociation of dislocations visually obvious. As stacking fault energy decreases further, with successive addition of solute in the matrix, there is an increased tendency toward dissociation of dislocations and cross slip becomes progressively more difficult. Eventually, when the stacking fault energy is "low" enough, complete dissociation of dislocations is seen to occur as shown in Figs.

Jan 1, 1969

By J. D. Bateman

At Giant Yellowknife, where high grade gold-bearing orebodies are highly irregular in shape, geology has been applied extensively to the mining of ore. The classical functions of the mine geologist in the fields of exploration and mine development have been extended to guide ore extraction, ensuring "clean" mining and effectively reducing waste dilution. THE property of Giant Yellowknife Gold M.ines Ltd. is situated west of Yellowknife Bay on the north shore of Great Slave Lake, a distance of 600 air miles north of Edmonton, Alberta. The Giant claims were staked in 1935, the company was formed in 1937, and the main orebody system was disclosed by diamond drilling in 1944 following a geological study of the property by A. S. Dadson,* Consulting Geologist for the company. Production began in 1948 at the rate of 200 tons per day and, during 1950, reached a daily rate of 425 tons. During the first 3 years of operation a total of 366,000 tons was milled with an average grade of 0.79 oz of gold per ton. Work is in progress with an expansion to 700 tons per day in view. A descriptive account of the geology and gold-bearing shear zone has appeared previously.* The rock formations in the vicinity of Yellowknife Bay have been subjected to protracted pre-Cambrian tectonic deformation culminating in a series of late faults having a cumulative horizontal displacement exceeding 11 miles. The Giant property is underlain by part of an Archean sequence, several miles thick, consisting of basic volcanic flows and minor intercalated tuffs. The volcanic succession forms the west limb of a major syncline, the flows facing east, but overturned on Giant property to dip west at 65" to 75". Orebodies are confined to shear zones up to 200 ft in width, which were formed along early thrust faults. The shear zones assume fold-like attitudes, the larger of which have an amplitude of several hundred feet. The rock formations beyond the limits of the zone of shearing do not reflect the simulated folds, the axes of which are within a few degrees of the strike of the flows. The schistosity and most of the planar elements in both the shear zones and the orebodies dip west • A. S. Dadson and J. D. Bateman: Structural Geology of Camdian Ore Deposits, Can. Inst. Min. Met. Jubilee Volume (1948), PP 273-283. at angles between 65" and 75", generally corresponding to the dip of the flows. The planar elements within the shear zone system thus dip more or less constantly west whether the shear zone is flat, vertical, or expressed as east or west dipping limbs. The shear zones reflect the deformation and alteration of the basic volcanic flows into chlorite schists which, in most places, have undergone metasomatic replacement to form chlorite-sericite-carbonate schists or sericite schists. The boundaries between the shear zones and country rock, although often gradational, usually can be defined within a few feet or even inches as they are expressed by the limits of metasomatic alteration. Orebodies may occupy a small or large proportion of the shear zone and, although they generally conform to the shape of the zone, their morphology is much more complex. Ore boundaries in some instances are sharp and can be delineated with a chalk line; but more generally, a large proportion of the ore boundaries is not visually obvious and can be determined only by the perception acquired by the geological mapping of ore or study of drill cores. Ore shoots in fold-like attitudes may transect the planar elements of the shear zone at any angle; yet the schistosity within the ore shoot may be coincident with that in the enclosing shear zone. Thus it is clear that problems may arise in the delineation of mining boundaries. Ore generally consists of 20 pct or more quartz with ferruginous carbonates in sericite schist deposited in two dominant stages. The earlier stage limits of quartz with carbonate, pyrite, and very fine-grained arsenopyrite in lenses and bands. The later stage consists of quartz-carbonate lodes, in

Jan 1, 1952

By Paul D. Merica, L. J. Gurevich

In connection with other investigations on the properties and characteristics of chilled-iron car wheels, the question as to the best range of annealing temperatures was raised. Chilled-iron wheels are cast with a chill against the tread and the inside of the flange, the remainder being in sand. The composition of the metal is so chosen that under these conditions the trcad and inside of the flange will show white iron to a depth of from 5/8 to in. (15 to 22 mm.), the remainder of the wheel becoming graph itized or gray. In order to relieve the stresses set up during cooling under such drastic conditions, the wheels are stripped from the mold, while still red hot, piled in a soaking pit, and allowed to cool very slowly from their temperature at stripping. Obviously the most suitable temperature for this annealing is the highest at which no formation of graphite occurs within the white tread and at which the wheels can be stripped from the molds. Inasmuch as no direct determinations have been made of the temperatures at which the formation of graphite takes place in white iron of compositions used in car wheels upon annealing, it was considered worth while to determine these temperatures as a means of establishing the maximum temperatures at which the annealing of the wheels may be carried out. In the course of this work, some incidental observations were made which are of interest in connection with the theory of graphitization in whitc iron. The literature on the subject of the formation of graphite both during cooling at casting and upon annealing is very extensive and can be best studied by reference to a comprehensive discussion of the subject by Hatfie1d.l Perhaps the most important contributions of previous investigation are the following: 1. Whether a given mass of molten iron becomes white, mottled, or gay upon casting, depends on its composition and its rate of cooling through the temperature range of solidification and immediately below. 2. The more rapid the rate of cooling, the less is the extent of graphitization.

Jan 1, 1920

By J. L. Wilson, D. L. Emmons

The Tucker Hill perlite deposit is located in the northwestern portion of the Devils Garden lava field in Lake County, south-central Oregon. The perlite occurs in the chill margin of a late Miocene composite rhyolite lava dome that exhibits distinct cooling zonation. The chill margin is composed of an outer glass envelope, which contains commercial-grade granular and vesicular perlite, and an inner glass envelope, which contains onionskin perlite of local commercial quality. Glassy rhyolite and rhyolite compose the lava dome core. The entire dome complex encompasses at least 5 km2 (2 sq miles). Expansion tests in commercial-scale furnaces indicate that the perlites are suitable for a wide range of applications and compare favorably with commercial perlite ores. The large tonnage deposit appears competitive for markets in the midwestern and upper northeastern states, and the Pacific Northwest of the US.

Jan 1, 1986

By C. Baldwin Sawyer

During the last half century, much time has been devoted to investigations of the effect of nitrogen on the physical properties of steel, but in all discussions of results there is considerable doubt as to the accuracy and interpretation of analyses. No conclusions concerning the effects of nitrogen on the physical properties of steel can be more reliable than the methods used for determining the quantities of nitrogen present. The work described in this paper endeavors to establish some additional conditions required by the customary distillation method for reliable and nccurate determinations. Results by a combustion method of analysis for total nitrogen content are presented; these indicate that all of the nitrogen in steel, exclusive of that contained in blowholes, may be determined by the distillation method. Based on these more sound and more reliable analyses, results havc been obtained that bear on the following divisions of the general subject, nitrogen in steel: Nitrification of steel by melting in nitrogen, nitrification of steel by heating in ammonia, decomposition of nitrified steel by heating, and thermal analysis of nitrified steel. Consideration of Two Methods of Analysis and Some Results The details of the distillation and combustion methods are chemical in character and of little interest to most readers. They are therefore described in an appendix. The distillation method is essentially that described by Hurum and Fay1 and was generally used throughout this work. It is capable of the greatest accuracy and all results given are significant to the last, figure. Where analyses do not check, the samples

Jan 1, 1923

By C. Baldwin Sawyer

During the last half century, much time has been devoted to investigations of the effect of nitrogen on the physical properties of steel, but in all discussions of results there is considerable doubt as to the accuracy and interpretation of analyses. No conclusions concerning the effects of nitrogen on the physical properties of steel can be more reliable than the methods used for determining the quantities of nitrogen present. The work described in this paper endeavors to establish some additional conditions required by the customary distillation method for reliable and nccurate determinations. Results by a combustion method of analysis for total nitrogen content are presented; these indicate that all of the nitrogen in steel, exclusive of that contained in blowholes, may be determined by the distillation method. Based on these more sound and more reliable analyses, results havc been obtained that bear on the following divisions of the general subject, nitrogen in steel: Nitrification of steel by melting in nitrogen, nitrification of steel by heating in ammonia, decomposition of nitrified steel by heating, and thermal analysis of nitrified steel. Consideration of Two Methods of Analysis and Some Results The details of the distillation and combustion methods are chemical in character and of little interest to most readers. They are therefore described in an appendix. The distillation method is essentially that described by Hurum and Fay1 and was generally used throughout this work. It is capable of the greatest accuracy and all results given are significant to the last, figure. Where analyses do not check, the samples

Jan 1, 1923