Search Documents

By C. K. Eilerts, J. D. Ham

Laboratory research has been conducted to evaluate the characteristic effects of condensate saturation on the mobility of gas in typical reservoir rocks. A pump with two pistons provided phases in equilibrium at controlled flow rates and constant liquid-vapor volume ratios. Core samples were tested in a holder that permitted sealing steady-state phases in the pore spaces under flow test pressures for weighing with sufficient precision to give an accurate measure of the attained saturations. Parameters of the study were pressure, apparent velocity, flowing liquid-vapor volume ratio, fluid composition, core material and length-to-diameter ratio. Tests were conducted at 515 and 1,515 psia to determine the effect of pressure on the mobility-saturation relationship. Influence of the apparent velocities 0.30, 0.15 and 0.07 cm/sec and of five liquid-vapor volume ratios from 0.0001 to 0.01 was determined at 515 psia The principal fluid system was nitrogen and and separator liquid from a Gulf Coast condensate, but the effect of a condensate of different viscosity was also determined. The significance of a possible concentration of liquid near the outlet end of the test cores was investigated. Core materials included a consolidated sandstone and a low-permeability limestone. Relative mobility and liquid-vapor volume ratio relationships are concluded to be dependent on pressure, saturation and, to a lesser extent, on velocity. For each porous medium and fluid there is a minimum saturation essential to two-phase flow, and high velocities of flow have only limited effect on saturations in this range. INTRODUCTION It is now recognized that knowledge of the availability of a reservoir gas — the period that gas may be recovered from a reservoir at a given rate — is as important as the estimate of gas in place. When reservoir conditions are such that pressure decline owing to production will result in retrograde condensation, liquid saturation can increase in the structure around the production well in a way that may restrict flow capacity, and hence future availability. l Based on a numerical solution of transient radial flow of single-phase gas-condensate fluids, 2 a program for computing the accumulation of condensate in a reservoir and the effect of this condensate on deliverability has been developed. During this development a need evolved for data that described the influence of pressure, velocity of flow and condensed liquid on mobility as recovery progressed. This paper presents the results of experimental investigation to obtain insight into the mobility relationship at reservoir pressures of gas-condensate fluids. A core holder for flow tests at reservoir pressure was developed to weigh the core and its fluid contents under pressure to determine saturation. A specially constructed pump was used to drive a two-phase fluid through the core until a steady state prevailed. The core was used as a differential device, and properties measured were intensive rather than extensive. APPARATUS Fig. 1 shows a schematic representation of the major pieces of equipment used in the mobility determination. The weighable core holder is connected to a two-piston, constant-displacement pump. Attainment of steady-state flow is indicated by stability of the flow differential read from the high-pressure manometer. WEIGHABLE CORE HOLDER An important part of the data needed was the mobility-saturation relationship. This required that mobilities and saturations be measured at pressures, flow velocities and liquid-vapor volume ratios characteristic of condensate reservoirs.

The Oregon School of Mines Society held its regular monthly meeting on the evening of October 23. This meeting was an informal reunion at which members gave accounts of personal experiences during the last three months. Many members of both junior and senior classes answered their country's call to arms and so did not return to college. The senior class is particularly well represented in the Army, as two men hold lieutenant's commissions and a third is already in France with a hospital unit. The junior class has also contributed men to various branches of the service. Plans for the regular meetings include discussions by members and lectures by outside authorities oil mining and allied topics. These meetings are open to the lower classes and all others interested. The Oregon School of Mines Society, composed of members of the junior and senior classes, has, joined with the sophomore and freshman relining students in purchasing a Liberty Bond under the name of the Miners' Club of 0. A. C. H. W. THOMS, President.

Jan 12, 1917

By Rollyn P. Jacobson

The town of Pacific, in Jefferson County, Mo., is 27 miles west of St. Louis. Since the area lies entirely on the flood plain of a cut-off meander of the Meramac River, it was considered a likely environment for accumulation of commercial quantities of sand and gravel. Excellent transportation facilities are afforded by two major railways to St. Louis, and ample water supply for washing and separation is assured by the proximity of the river. As a large washing and separation plant was planned, the property was evaluated in detail to justify the high initial expenditure. An intensive testing program using both geophysical and drilling methods was designed and carried out. The prospect was surveyed topographically and a 200-ft grid staked on which electrical resistivity depth profiles were observed at 130 points. The Wenner 4-electrode configuration and earth resistivity apparatus* were used. In all but a few cases, the electrode spacing, A, was increased in increments of 1% ft to a spread of 30 ft and in increments of 3 ft thereafter.

Jan 2, 1955

ADVANTAGES OF LIFE MEMBERSHIP The Institute calls the attention of members to the following advantages of obtaining life membership: 1. One payment avoids the trouble of future payments. 2. The interest on $150 is less than the annual dues. 3. Provision is thus made early in life for the less productive years. 4. In case of in increase of clues at any time in the future life members are exempt from increased payments. Excerpt from, By-Laws. Article III. Section 3 Any Member or Associate not in arrears may become, by the payment of one hundred and fifty dollars at one time, a Life Member or Life Associate, and shall not be liable thereafter to pay annual dues. The money thus received shall be invested and only the income thereof used for current expenses of the Institute.

Jan 1, 1916

By H. R. Hanley

ONE of the most important contributions to the art of electrolytic zinc production-has been the aluminum cathode. This has been used in all major production: since its commercial development in 1916. The literature is replete with important contributions, some of which may have been replaced by better ones, but thus far there appears no other metal to take the place of aluminum as cathode material. Credit for this innovation goes to Sherard Cowper Coles, of England. When experi-menting on the extraction of-zinc from Broken Hill ore at Hayle, Cornwall, in 1893, he introduced the aluminum cathode, and in 1895 obtained British Patent-No. 20073. The reason for this dominant position of aluminum as cathode mate-rial in zinc sulphate electrolytes is its unique surface, to which electro-deposited metals usually do not tightly adhere. The metal must be of high purity for best results. It is possible to develop a starting-sheet method by which thin electro-deposited sheets of cathode zinc are made and stripped from a smooth aluminum plate. Such thin sheets of cathode zinc may be used as arc tine copper sheets in standard electrolytic copper-refinery practice. However, complications arise because of extreme warping of the zinc starting sheet after a .few hours of deposition, and thus special arrangements must be made to compensate for this abnormality.

Jan 1, 1938

By Charles W. Bauer

Most of the aluminum produced in the United States today is derived from foreign bauxite deposits. Earth Sciences, Inc. initiated a program to evaluate domestic non bauxite sources for alumina in the 1960's. In the initial evaluation of alunite, domestic resources were not sufficient to support development. An exploration program led to the discovery of large deposits of alunite in Utah and several other western states. Identification of alunite is difficult as both its physical and chemical characteristics are similar to the minerals with which it is associated. Most of the significant alunite deposits in the western United States are replacement type deposits. These deposits have formed as a result of hydrothermal alteration of volcanic, sub-volcanic, and igneous rocks. Typical alunite deposits contain between 30 and 50% alunite and 50 and 70% quartz, with minor amounts of other minerals. Four mineralogical zones are common in these systems. They include a siliceous zone, a quartz-alunite zone, a kaolinite zone, and a chlorite-montmorillonite zone. Total US reserves of alunite were estimated at 20 Mt fat 30% alunite) by the US Bureau of Mines in 1941. More recent work by the US Geological Survey estimates reserves of 252 Mt and potential resources at 1.4 Gt. Reserves and resources estimated for 23 properties on which field work has been done by ESI are considerably higher. Most of these properties have reserves and potential resources of several hundred million metric tons. The combined demonstrated reserves of these properties are estimated to be about 650 Mt. Inferred reserves are estimated at 2.5 Gt and potential resources at 8 Gt. It appears that the US has sufficient reserves and resources for alunite to be considered as a potential nonbauxite source of alumina.

Jan 1, 1982

By N. J. Grant, D. Carne, J. B. Seabrook

IT is unnecessary to review much of the literature on hydrogen embrittlement of steel since several excellent reviews and bibliographies exist.1-3 Hot acid pickling and cathodic charging have been known to cause hydrogen embrittlement of steel and have been used as laboratory methods to charge steels with hydrogen.4-8 Experimental Procedure The problem of prime concern in all instances, except in the work of Sims and coworkers,10 is that at no time was there a definite known hydrogen value reported which could be related to a particular value of the degree of embrittlement. It was the purpose of this research to determine the relationship between hydrogen content and degree of em-brittlement quantitatively. The 1020 stock used for the specimens was hot-rolled 7/16 in. diam rod of the following analysis: 0.19 pct C, 0.40 pct Mn, 0.012 pct P, 0.036 pct S' Vacuum-fusion analyses for nitrogen and oxygen gave 0.014 pct O2 and 0.0011 pct N2. Cathodic charging was used to cause embrittle-ment. The advantages of this method were that no quenching was necessary, the impregnation was reasonably controllable, and representative samples for analysis could be prepared simultaneously with the charging of the tensile bars. Analyses for hydrogen were made in a vacuum-fusion type of apparatus which extracted gas from the samples by fusion in a molten tin-iron bath' This apparatus, which has recently been described in detail elsewhere, will not be discussed here.". " Consecutive samples can be analyzed every 15 min with an accuracy of 0'03 ppm. A A from an electrolytic or pickling bath can be charged for analysis in about 3 min, and analysis completed in 15 min. Samples of as-received 1020 stock were analyzed and found to contain a negligible amount of hydrogen (0.06 ppm). Preliminary pickling and electrolytic charging gave highly variable results. Cold-worked samples showed higher values but ranged from 0.6 to 6.0 ppm of hydrogen. Charging at 90°C gave higher values of charged hydrogen, but troublesome films on many of the specimens resulted. It was not until a few drops of a catalytic poison, prepared from 2 g of yellow phosphorus dissolved in 40 ml of carbon disulphide,8 was added to the electrolytic cell that fairly consistent high values of hydrogen could be charged into the as-received 1020 steel at room temperature. The cell used is sketched in fig. 1. The anode and fixture for the tensile specimens were fastened to the cell cover as shown, and the specimen was screwed in place, centrally located with respect to the anode. At first, anodes of lead and graphite were tried, but they contaminated the electrolyte and gave a slight deposit on the specimen. Later, a platinum wire was used in the form of a uniform helix. A current of 2 amp, corresponding to about 0.5 amp per sq in. of cathode, was used for most specimens. The electrolyte was 4 pct H2SO4 solution. Fig. 1 shows the form of the special tensile bar, the main portion of which was an ordinary 1/4 in. diam, 1 in. gauge length test bar, except that two to four small cylinders of stock were left attached by small links to the bottom end of the tensile bar for the purpose of providing samples for hydrogen analysis. Thus the bars and samples were charged with hydrogen simultaneously and an analysis could be made while the bar was being tested mechanically. Experiments were performed to determine how representative the test cylinders were of the middle of the test bar proper. While the bar center was being analyzed, the small cylinder was stored in dry ice, since it had been shown that such storage prevents loss of hydrogen for many hours.12 The results of these checks are shown in table 1. The checks are very good (0.3 ppm) and indicate that it is permissible to use the small end cylinders to establish the hydrogen content of the tensile test bar proper-

Jan 1, 1951

By N. J. Grant, C. C. Wang

The Ti-Cr-O ternary system has been studied in detail near the titanium-rich corner within the limits of 10 wt pct 0, and 20 wt pct Cr. Studies were extended, but not in detail, to the region beyond 25 wt pct 0, (50 atomic pct) and 62 wt pct Cr (60 atomic pct). Four isothermal sections at 1400°, 1200°, 1000°, and 800°C are presented as well as two vertical sections at 1 and 2 wt pct 02. DURING the last decade much interest has been shown in the development of high strength titanium alloys for high temperature and corrosion resistant applications. Extensive research is being carried out at present, as the current literature indicates, in order to study the properties of titanium and to develop improved alloys. Two of the important alloying elements in commercial titanium alloys are chromium and oxygen and it would be desirable to know their combined influence upon titanium. For this purpose the present work was carried out to investigate the titanium-rich corner of the ternary system TiICr-0. The binary systems Ti-Cr and Ti-0 have been published recently. The Ti-Cr system was studied by several investigators " and their results are in close agreement. The eutectoid decomposition of the B phase has been shown to be extremely sluggish. TiCr, was the only intermetallic compound found in this binary system and was formed at 1350°C by a transformation from the p phase. TiCr? was established as the cubic C 15 (MgCu,) type of structure with 24 atoms per unit cell and was designated as the y phase. This terminology will be adopted in the present work. There was disagreement about the actual composition of this compound among the several investigators, although it is evident from their data that the compound probably has a solubility range of about 2 to 3 pct and is in the vicinity of 65 pct Cr. It has been indicated recently that a high temperature modification of this y phase (TiCr,) existed at a temperature above 1300°C." ' This high temperature modification was identified as a hexagonal C 14 (MgZn,) type of structure with 12 atoms per unit cell. The exact transformation temperature from the high temperature phase to the low temperature phase has not been established. A considerable hysteresis was observed and, due to the sluggishness of this transformation, the high temperature phase often co-existed with the low temperature phase at temperatures below 1300°C. A preliminary study of several Ti-0 compounds and the Ti-0 system had been carried out by Ehr-1ich."-"' The most complete binary Ti-0 system was the one reported recently by Bumps, Kessler, and Hansen." The first intermediate phase found in the system was the 8 phase which formed by a peritec-toid reaction of the phases a and Ti0 at temperatures below 925 °C. This reaction is extremely sluggish. The structure of this 8 phase was tentatively identified by these authors as being tetragonal and the lattice constants were found as c,, - 6.645A, a,, = 5.333A and c/a = 1.246A. Experimental Procedure The raw materials used for this investigation were TiO,, electrolytic chromium, iodide titanium, and sponge titanium. The TiO, was in the form of powder of chemically pure grade (99.8 pct pure). The chemical analysis of the electrolytic chromium was: 0, 0.50 pct; Fe, 0.07; Cu, N, and C, 0.01; and Pb, 0.001. The oxygen in the chromium was calculated as part of the final oxygen content of the alloys. The alloys were prepared by the cold crucible method using a tungsten arc. The entire system was evacuated and flushed with purified helium three times and then filled with helium. Each alloy was melted, turned over, and remelted at least four times to insure homogeneity. The total melting time was generally from 6 to 10 min. A master alloy of 25 pct 0,-75 pct Ti was prepared to facilitate alloying by melting compacts of TiOl powder with either iodide or sponge titanium, yielding the compound TiO. It was found necessary to bake the TiO, powder compact at about 150°C to remove adsorbed moisture. This was done to prevent the disintegration and spattering of the compact when the arc was struck. TiO, powder dissolved quite readily into the melt and no other trouble was encountered.

Jan 1, 1955

By G. Purcell, S. C. Sun

The objective of the present study was to detennine the role played by double bonds in the flotation of a very pure mineral using 18-carbon unsaturated fatty acids as collectors. Streaming potential measurements were made on a plug of pure synthetic rutile in solutions of inorganic electrolytes and unsaturated 18-carbon fatty acid soaps. Experimental results from these tests are detailed in the paper. The collector effectiveness of oleic acid with one double bond, linoleic acid with two double bonds, and linolenic acid with three double bonds has been a matter of speculation for many years, and conflic- ting experimental evidence1-8 has not clarified the issue. The overall objective of the present study was to determine the role played by double bonds in the flotation of a very pure mineral using 18-carbon un-saturated fatty acids as collectors. Since zeta potential is dependent on adsorption and orientation of ions at the solid-liquid interface, its variation under different conditions of pH and collector concentration should throw some light on the behavior of unsatu-rated fatty acids in flotation pulps. Titanium dioxide, in the form of rutile, was chosen for the investigation because it is now available in a very pure, synthetic, crystalline state, and despite the fact that it is one of the most important synthetic inorganic chemicals in commercial use, its electro-kinetic properties have not been closely studied. Electrokinetic properties of rutile in various aqueous solutions are discussed in this paper. Adsorption information gained from the streaming potential measurements enabled the flotation resultsg to be explained in a qualitative way, thus providing a clearer

Jan 1, 1963

THE paper on "Cross-cuts in Coal Mining," by J. J. Rutledge (published in MINING AND METAL-LURGY, February, 1927, p. 64) was brought up for discussion at the annual meeting, where the follow-ing comments were made T. D. Thomas (Lehigh Coal & Navigation Co., Lansford, Pa.) : This question has caused me a lot of worry, not in the particular district in which I am, but throughout other districts. There are always several angles to consider. If you are in a hurry to push development work, you might increase the distance between cross-cuts from 60 to 350 ft., but if you have a 40-ft. chain pillar every 60 ft. it will cut down your entry driving a whole lot. Looking at it from the ventilation angle, I agree that too many cross-cuts in entries are bad things. You have a tremendous amount of leakage, and I have seen currents starting out with 45,000 cu. ft., and after passing about 30 or 40 cross-cuts the current has dwindled down to about 18,000 or 15;000 cu. ft. The result is that the question of putting in auxiliary fans is raised. That involves several points into which I do not want to go too far, but I am in favor of not getting in too many cross-cuts, putting them in only where they are necessary: I think the state mining laws are wrong in a number of places on that, and that when you finish with a cross-cut it should be in the room. It should be well sealed on an entry. There are several ways of tightening up the cross-cuts so as not to have the great amount of leakage and wastage of: air that we now have. 'I prefer tile stopping; other people prefer cement or brick, but there is a big fac-tor to all mines, saving the mine. I checked up on the number of fans in the anthracite region and found there are 651. That was derived from the state report of 1921, and it enabled me to compute from the power the weight of the air. In the anthracite region of Pennsylvania we put in 9 tons of air to every ton of coal we get out. Tracing that back again and taking the Government's figures which they made some time ago, I found but 20 per cent of the air got to the faces where it was actually needed. That is a tremendous big loss and shows a possibility for saving, money for the various coal companies. Chairman Rice: I think what Mr. Thomas refers to was an investigation by R. Y. Williams, of the Bureau of Mines in Illinois, where a study was made of 100 typical mines, and, speaking off-hand, my recollection is that we found as little as 15 per cent of air reached the faces in one of the mines and another was as much as 50. That seems to be a reflection on the type of stoppings and general ventilation scheme.

Jan 3, 1927

By Clarence Merritt

STAINLESS iron, as mild stainless steel is usually called, an alloy ranging from 11.50 to 15.00 per cent chromium with carbon under 0.12 per cent, has been considered to be not appreciably affected in respect to corrosion resistance by heat treatment. This metal, while one of the most widely used of the "straight" chromium stainless alloys, has failed in many applications because of insufficient information regarding heat treatment. These failures have been attributed to many possible causes from an inherent lack of resistance to corrosion and misapplication to mysterious electrolytic effects or comparatively minute non-metallic inclusions. Many uses for a steel with such excellent physical properties is are latent in this alloy have been lost on account of corrosion failures which could have been avoided by applying proper heat treatment. The alloy has not received the recognition or attention it should because of the fact that' the details of its metallurgical behavior were not thoroughly understood. Response to heat treatment of the steel is well known as regards tensile properties, 1,2 but its application has been for improvement in tensile characteristics or on account of machining considerations rather than for corrosion prevention. The potential user of this steel has not been clearly advised in papers, either technical or commercial, that have been written about it in the last 10 years or more, of particular features that are of prime importance in developing the excellent properties of this metal. The data to be presented in this paper are concerned mainly with the effect of heat treatment on the corrosion resistance, but a study has also been made of the concurrent microstructural changes and an explanation developed for the phenomena revealed, as well as a correlation to the other physical properties-hardness, tensile characteristics and impact strength. Stainless steel, largely used for cutlery purposes, an alloy of approximately 13.00 per cent Cr with 0.30 per cent C, must be hardened and the surface prepared by polishing or pickling for best resistance to staining and corrosion.3 Monypenny reports that a loss of hardness is

Jan 1, 1932

By D. W. Fuerstenau

This paper presents the results of an investigation of the stability of the mass flow rates and average pellet size in the different streams of an industrial-scale balling circuit. The variables in this study include water content, drum speed, and fresh feed rate. It was found that both the mass flow rates and pellet diameter are greatly disturbed when a change, positive or negative, in any of the variables takes place. For most of these disturbances to be damped down, a period of 1 hr or so is required. When a disturbance in the feed rate was made, the transient period extended to more than 1% hr (the duration of the experiment). It was observed that there is an interaction between the drum speed and moisture needed for producing an acceptable green ball product. The moisture content of the product pellets was found to be a function of the pellet size, with the larger pellets retaining a higher moisture content

Jan 1, 1983

By Carl Zapffe

A Rise in less than ten years from obscurity into great prominence economically, tersely summarizes the history and status of the Cuyuna manganiferous iron ores. The Cuyuna district produces and ships mostly high-phosphorus iron ore, but the annual production of manganiferous iron ore is increasing rapidly and productions from individual mines are becoming more regular and more dependable as to grades and tonnages. This ore bids fair to become, shortly, the principal product of the district and is responsible for its present economic prominence. The iron ores of the district have been described, by the author and others, in many publications and will not be discussed here. Lately the manganiferous iron ores have been given some attention, but the range and variations of chemical composition of the ores, the principal physical characteristics of the ores and their deposits, the relative importance of the different ores and their possibilities in future developments, and the life of the respective reserves have not been discussed. It is impossible to give all of this information with the positiveness necessary for it to constitute a reliable guide for investment or even for future mine development. Each property and each party presents a special case and deserves critical consideration. We are dealing with special ores and always with a set of new conditions. Sufficient information of a general nature can be given, however, to indicate the reason for and the trend of the presently augmented developments in the district. In a great thickness of a big variety of sedimentary rocks, probably of Upper Huronion age, prevailingly of green, schistose phases of slaty and volcanic material intricately intermixed, lies a thin bed containing lenses of iron-bear ing formation. These lenses occur singly or in groups, thus causing the variation in the thickness of the formation; or they are separated at their ends and give rise to discontinuity or they overlap and display continuity with lateral offsets. Intense folding has added to the complications.

Jan 1, 1925

By Keith T. Griffiths

INTRODUCTION The Empress Nickel Mine is situated forty-eight kilometres west of Kadoma in the Zhombe Communal Land of Zimbabwe. The mine came into operation in late 1968 based on a proved and probable ore reserve of twenty million tonnes. The initial production rate was 55 000 tonnes per month from underground. This was boosted to 85 000 tonnes per month in mid 1970 when the opencast operation came into production. The mining method at Empress is sub-level open stoping with main haulages mined at ninety metre intervals and sub-levels at eighteen metres. The extremely wide ore body of up to one hundred metres in width has necessitated leaving extremely large rib pillars and sill pillars in position to maintain mine stability and to act as regional support of the hanging wall. In early 1976 the opencast operation had reached its final economic depth and it was then necessary to increase underground production to 85 000 tonnes per month. Since a large portion of the ore reserve remained in both rib and sill pillars, it was necessary to embark on a positive pillar recovery programme. For this reason it was decided to introduce a sandfilling programme for the mined-out stopes and a modified system of sub-level open stoping with post filling of the lower stopes. ORE BODY GEOLOGY AND GEOMETRY The Empress orebody outcrop has a strike length of nine hundred and fifty metres on a north west - south east axis. It is a steeply dipping (65' - 75') tabular orebody of gabbroic rock which has been extensively altered. The north west - south east strike length of nine hundred and fifty metres on surface reduces to some two hundred

Jan 1, 1983

By N. P. Peterson

The Castle Dome copper deposit is of the porphyry type and occurs in a body of quartz monzonite intruded into the pre-Cambrian formations and possibly into the lower part of Paleozoic limestones. The hypogene sulphide minerals include pyrite, chalcopyrite, and a little molybdenite, sphalerite, and galena. Pyrite and chalcopyrite are disseminated or occur in small closely spaced veins. The hypogene mineralization shows distinct zoning in the distribution of pyrite and chalcopyrite, so that the mineralized area can be subdivided into pyritc and chalcopyrite zones. Supergene enrichment, though not extensive, played an important part in the formation of the ore body, the chalcopyritc zone being the pro-tore. Several thin, gently dipping, diabase sills occur in the mineralized area, and the copper content of the rock in and near these sills is substantially higher than average. The formation of the ore body was caused by the combined effects of three forces: I. Zoning of the hypogene mineralization, 2. Richer copper metallization associated with the diabase sills, and 3. Supergene enrichment. Introduction The Castle Dome copper deposit is about 5 miles west of Miami, Arizona, and about 3 miles west of the Miami-Inspiration ore body. The Castle Dome open-pit mine is on the south flank of Porphyry Mountain, a prominent landmark of the region. In 1941 the deposit was being explored by the Miami Copper Co., but the exploration program was cut short when the decision was made to develop the property as a war project. The Castle Dome Copper Co., Inc., was organized as a wholly owned subsidiary of the Miami Copper Co., and arrangements were made with Defense Plant Corp. for developing and equipping the mine and for construction of a concentrating plant. Construction and development work was begun in January 1942, and milling operations started June so, 1943. Since that date, the mine has been in continuous operation by the Castle Dome Copper Co, under a lease agreement with Defense Plant Corp. producing copper at an average rate of 4,000,000 lb per month. To January I, 1946 the total production amounted to 121,088,000 lb of copper,4,271 oz of gold, and 211,755 oz of silver. A detailed study of the copper deposit and the surrounding area was undertaken by the U. S. Geological Survey in June 1943. Other members of the Survey participating in the work were C. M. Gilbert, G. L. Quick, and J. P. Albers. The results of this work will be published as a comprehensive report by the Geological Survey. General Geology The Globe quadrangle, which includes the Castle Dome area, was studied by F. L. Ransome1 of the Geological Survey in 1901 and 1902. His maps and descriptions were

Jan 1, 1949

By N. P. Peterson

The Castle Dome copper deposit is of the porphyry type and occurs in a body of quartz monzonite intruded into the pre-Cambrian formations and possibly into the lower part of Paleozoic limestones. The hypogene sulphide minerals include pyrite, chalcopyrite, and a little molybdenite, sphalerite, and galena. Pyrite and chalcopyrite are disseminated or occur in small closely spaced veins. The hypogene mineralization shows distinct zoning in the distribution of pyrite and chalcopyrite, so that the mineralized area can be subdivided into pyritc and chalcopyrite zones. Supergene enrichment, though not extensive, played an important part in the formation of the ore body, the chalcopyritc zone being the pro-tore. Several thin, gently dipping, diabase sills occur in the mineralized area, and the copper content of the rock in and near these sills is substantially higher than average. The formation of the ore body was caused by the combined effects of three forces: I. Zoning of the hypogene mineralization, 2. Richer copper metallization associated with the diabase sills, and 3. Supergene enrichment. Introduction The Castle Dome copper deposit is about 5 miles west of Miami, Arizona, and about 3 miles west of the Miami-Inspiration ore body. The Castle Dome open-pit mine is on the south flank of Porphyry Mountain, a prominent landmark of the region. In 1941 the deposit was being explored by the Miami Copper Co., but the exploration program was cut short when the decision was made to develop the property as a war project. The Castle Dome Copper Co., Inc., was organized as a wholly owned subsidiary of the Miami Copper Co., and arrangements were made with Defense Plant Corp. for developing and equipping the mine and for construction of a concentrating plant. Construction and development work was begun in January 1942, and milling operations started June so, 1943. Since that date, the mine has been in continuous operation by the Castle Dome Copper Co, under a lease agreement with Defense Plant Corp. producing copper at an average rate of 4,000,000 lb per month. To January I, 1946 the total production amounted to 121,088,000 lb of copper,4,271 oz of gold, and 211,755 oz of silver. A detailed study of the copper deposit and the surrounding area was undertaken by the U. S. Geological Survey in June 1943. Other members of the Survey participating in the work were C. M. Gilbert, G. L. Quick, and J. P. Albers. The results of this work will be published as a comprehensive report by the Geological Survey. General Geology The Globe quadrangle, which includes the Castle Dome area, was studied by F. L. Ransome1 of the Geological Survey in 1901 and 1902. His maps and descriptions were

Jan 1, 1949

By K. A. Lambert

In the Anthracite Region there are considerable areas where the original mining was done 50 or more years ago. In this original mining, the pillars that were left proved inadequate in size for the support of the roof, which has since collapsed as a result of squeezes, and completely filled the original openings. In an endeavor to recover the coal which remains in the pillars in such areas, the reopening cost for development, as well as for pillar recovery, has been excessive in many instances. Various methods have been tried out with a view to lowering the cost, in order that the greatest possible percentage of recovery of the reserve tonnage may be realized economically. Ordinary hand mining necessitates the driving of development road 10 ft. wide in the clear between timber legs, with 6 ft. of clearance over the rail to accommodate mine cars; collars or crossbars on the timber sets have been difficult to maintain in these openings in the heavily caved condition, especially in beds where the overburden is great,. Numerous failures have occurred on these development road timbers because of roof movement resulting from removal of pillars. The actual removal of pillars from this development work has been costly because full-width openings for transporting mine cars to the face have to be maintained by cleaning caved material from alongside the pillars, or skipping up along the pillars where pillars of sufficient width are found. Shaker-chute Methods A method of developing such caved conditions and recovering pillars tributary to this development, utilizing shaker chutes, is being tried out with considerable success at Loree colliery. An outline of the chute and apparatus is shown in Fig. 1, which indicates the location of pillars and caved material. The cost of both labor and material required in the recovery of such coal is considerably less than by ordinary hand methods. In order to try out this method of mining a location was chosen where a tightly caved area had been developed by ordinary hand methods to within 300 ft. of the property line. The original bed height was 12 ft., with an overburden of 325 ft., but on account of the squeezes which

Jan 1, 1931

By D. S. Eppelsheimer, D. N. Williams

The compression texture of iodide titanium is determined and found to consist of a [0001] texture rotated 15° to 30° from the axis of compression. As the amount of reduction increases, the angle of rotation decreases. The 0001 rotation showed a slight preference for a <1010> rotation axis. RECENT investigation of the cold rolled texture of titanium&apos; has shown this metal to exhibit a new type of rolling texture. This texture can best be described as a (0001) [10i0] with the 0001 planes rotated approximately 30" to the transverse direction around a <10i0> rotation axis. Rather good results in explaining the cold rolled texture have been obtained by other workers&apos; by examination of the tension and compression textures. No information was found giving the tension texture of titanium. Generally the tension texture of a hexagonal close-packed metal is identical with its wire texture. The drawn texture of titanium has been investigatedh nd has been found to be predominately [10?0]. Since this is the common tension texture of hexagonal metals of low c/a ratio, the explanation of the difference between the rolling texture of titanium and the rolling texture of other hexagonal metals is not indicated by examination of the tension texture. Therefore, the compression texture of titanium should be particularly important in the explanation of the unusual transverse rotation of the 0001 planes found in the cold rolled texture. The compression texture of titanium was examined by Yen.",&apos; His results showed titanium to exhibit the usual [0001] texture up to 85 pct reduction. At higher reduction a double texture appeared in which the 0001 planes were rotated from 10" to 30" from the plane of compression. This change in the compression texture seemed unusual since the tendency for hexagonal close-packed metals is to approach the [0001] texture as the idea compression texture. Mechanical twinning generally occurs over a considerable range of reductions beginning at a rather low reduction. The samples used by Yen in his investigations were prepared by two methods. Compression in a testing machine was used up to a reduction of 85 pct. Compression by compression rolling was used at higher reductions. Since the change in texture occurred at the same reduction as the change in the method of compression, a connection between the two seemed likely. To check this possibility and to locate the position of the change in texture definitely, if it was found to exist, the compression texture of titanium was re-examined. An iodide titanium crystal bar (99.9 pct Ti) produced by the New Jersey Zinc Co. and donated by the Titanium Alloy Manufacturing Div. of the National Lead Co. was used in this investigation. Procedure The investigation of the compression texture was carried out in three steps; compression, specimen

Jan 1, 1953

By John Chipman, Raymond L. Orr

Recently reported high -temperatlnre thermal data have been incorporated in a reuieu&apos; of the therinody-r~ar,zic propesties of iron. The recent data permit mot corlsisterlt and reliuble choices to be made for many of the pvoperties, resnlling in bettev eslablished tabrtlations of the thermodynamic functions. Values of Cp, h°t- - H°298. s°t - S2sa, and (G°T -H298/T are tabulated for -the solid and liquid phases of iron in both stable and melastable regions. Consistency of the tabulations has been maintained to the precision necessr~vg to yield the Gibbs energy change belween the bcc (a, 8) and fcc (y) phases of iron at temperatures pertinenl to alloy studies. THE importance of the metal iron has stimulated many investigations of its thermodynamic properties at elevated temperatures. Reviews and summaries of the data have appeared from time to time. Among these the 1951 paper of Darken and smith&apos; deserves highest recognition for the quality of its criticism and for the precision and thermodynamic consistency of its tabulations. These and the more recent table of Kaufman, Clougherty, and weiss2 reproduce the Gibbs energy of the (a, 6)--Y transformation with sufficient sensitivity for alloy studies. Other recent compilations of equal validity3-&apos; make no attempt to do this. Since this Gibbs energy change is not greater than 22 cal per g-atom over the temperature range 1100° to 1800°K, it is obviously desirable to tabulate values of (G°t - H298)/T to four places of decimals even though the absolute accuracy would not warrant such precision. The necessity for reconsideration of the problem is emphasized by the recent publication of several important researches on the enthalpy and heat capacity of iron. The older work is well-covered in the reviews cited and will be mentioned here only when actually employed in the tabulations. GAMMA IRON Transition temperatures are taken from the selec -tions of Elliott and Gleiser,5 based on the work of Boulanger7 and earlier workers. For the a-y (A3) transition at 1184°K we retain the value 215 cal per g-atom adopted by Darken and smith.&apos; It has received confirmation in the recent work of Dench and Kubaschewski,&apos; and of Braun8 using adiabatic calori-metry, and of Wallace, Sidles, and Danielson10 using a pulse heating technique. The enthalpy data of Olette and ferrier" and of Anderson and Hultgren12 at higher and lower temperatures may be extended to 1184°K to give the following values which are adjusted to the required value of ? 1184 Ha,1184 Ha 298 = 8030 cal per g-atom [11 hr,1184-ha298 = 8245 cal per g-atom [2]

Jan 1, 1968

By Granville S. Borden, Frank H. Madison

The fruits of industry are divided between capital, labor, and governments. Capital takes its redemption and remuneration through profits or dividends; labor takes its share through wages; governments take their share through taxes. Each must have a just share, and the question of what is a just share and the question of who shall make the allocation are vital current political and economic issues. Certain political philosophies con- tend that government should take all the fruits and that some dictator or politician should have irrevocable discretion and power to distribute the fruits. Believers in democracy and free enterprise adhere to the view that capital is entitled to redemption and fair remuneration; that labor shall have a fair wage; and that governments shall make equitable levies. But since all human beings, both individually and in groups, are inherently selfish, there are many variable views in regard to the question of what ratios shall be applied in a division of the fruits and who shall have the power to fix these ratios. Perhaps all parties should devote more energy to means of increasing the crop, and not so much time to quarreling over a division of the existing crop. Moreover, all three parties must guard against killing the goose that lays the mineral eggs. For example, if the tax burden becomes oppressive and the taxpayer refuses to carry it, then business stagnates, with consequent unemployment, reduction of profits, and curtailment of government revenue. If a producer assumes the increased tax burden, marginal operations must be closed down, and, again the consequences are increased unemployment and diminished government revenue. Quite often an increase in a rate of tax results in a reduction of government revenue. Perhaps the worst detrimental feature of selfishness and greed on the part of any one of the three distributees of the fruits of industry is the retardation of expansion of the enterprise. Growth means new jobs, more government revenue, better trade, and better standards of living. Explorations and discoveries have resulted in tremendous contributions

Jan 1, 1964