Search Documents

By P. K. Koh

With identical annealing heal treatment the development of major annealed texture component seems to depend primarily upon the degree of cold reduction. Cube texture was evident on annealing- 1/2-, 1,/4- , and 1/8-mil tapes at 760°C, but it dissap-)eared on 927°C annealing of 1/8-mil tape cold reduced 96.9 pct. Some cube texturee remained as tile strongest 927 °C annealed texture component in 1/4- and 1/2-mil tapes cold reduced 93.8 and 87.5 pet, respectively. The switching coefficient increases and the squareness ratio of the hysteresis loop decreases proportionally with increasing cube pole concentration. PREVIOUS studies 1,2 on the 1/8-mil ultra-thin molybdenum permalloy tape established cold rolled and annealed textures and their magnetic performance for switch-core and coincident-current memory applications, The major cold-rolled texture was found to be of {110}<335> which is quite similar to the cold-rolled texture of silver and 70-30 cartridge brass. The major annealed texture components were found to be of {120)-- <001> and {113)<785>. Although the direction for easy magnetization for this type of alloy by the single-crystal technique is not avaliable, knowledge from related studies indicated [Ill] as the easy magnetization direction, similar to that of nickel.&apos; Therefore, a cube orientation, if present in the tape core, would be most detrimental to its magnetic performance.3 In its cold-rolled state the tape had < 111 > directions in the rolling plane 14.5 deg from the rolling direction.&apos; But the coercive force of the tape in such condition will be excessive due to large amounts of internal stresses, and therefore makes its use impossible for memory applications due to long switching time. In lower nickel alloys, suchas 50-50 nickel-iron and 65 pct Ni-Fe sheets, previous investigators4"7 found the presence of cube texture on annealing at 900° to 1000°C. Although no cube texture was found in annealed 1/8-mil tape,"&apos; its presence in some annealed 1,/4-mil tape cores was firmly established a year ago as verified by significant differences in magnetic properties. The present investigation is devoted to the orientation study and related magnetic measurements on three thicknesses of the ultra-thin tape, namely, 1/8 mil, 1/4 mil, and 1/2 mil, cold rolled directly from annealed 4-mil stock in the cold-rolled state as well as after they were annealed at 760°C (1400° F) and 927°C (1700°F). The results obtained might serve to elucidate the development of annealed texture as well as to establish clearly the importance of preferred orientation on the magnetic performance of such memory tape core despite its well-known low magnetic anisotropy exchange energy. EXPERIMENTAL PROCEDURE Samples were taken from one production heat (0.010 wt pct C, 0.004 P. 0.016 S, 0.80 Mn. 0.29 Si. 79.69 Ni. 4.42 Mo. 0.054 Co, 0.002 Ti, 0.12 Al, 0.04 Mg, 14.56 Fe). Annealed 4-mil sheets were cold re-

Jan 1, 1962

By Oliver Ralston

DURING experimental study on the separation of a zinc concentrate from the heavy sulfide ores of Jerome, Ariz., a great deal of attention has been given to proper activation of the sphalerite content of the ore. The sphalerite at Jerome contains enough iron to class it as a marmatite, as picked specimens have only about 60 per cent. zinc, whereas pure zinc sulfide contains 67 per cent, zinc. This marmatite in large pieces is black in color, but in dry powdered state is brown. A flotation froth made from it has a silvery black luster in comparison with a brassy luster caused by chalcopyrite which occurs in the same ores. The sample used in most of the experiments described below consisted of about 3000 lb. of diamond-drill core from the zinc-bearing orebodies of the United Verde mine, and had the following analysis: PER CENT. PER CENT. Oz. PER TON Cu 0.695 A1203 0.83 Ag 1.30 Zn 6.17 S...:: 43.35 Au 0.02 Fe 36.23 CaO 0.46 Si02 9.27 Mineralogically, this analysis is calculated to the following, which is in agreement with the microscopic examination: PER CENT. PER CENT. Chalcopyrite 2.0 Schist 3.2 Marmatite 10.32 Quartz 8.2 Pyrite 73.0 Calcite 0.9 All samples were ground in a laboratory ball mill in order to leave about 3 per cent. on a 200-mesh sieve, fine grinding being essential to liberate the minerals in the ore. Most of the Jerome ores are so intimately crystallized that reasonably complete unlocking by grinding does not take place until 800 mesh is approached. Therefore, the 200-mesh grind adopted contains a considerable amount of locked mineral grains, but not so much as. to render impossible the preparation of commercial grades of concentrate:

Jan 1, 1929

By G. Townsend Harley

STOPING methods in which shoveling plays an important part are gradually being replaced by other and cheaper methods. But there will always be considerable shoveling done underground in stopes as well as in drifts, tunnels, urinzes, and shafts. At the mines of the PhelpsDodge Corporation at Tyrone, N. M., the cost of shoveling in all stopes in 1917 amounted to 24c. per T. In the top-slice stopes for the same period, it cost 27 c. per T. or 16 per cent, of the total cost of these stopes. The tonnage for shovelers from all stoping was 9.3 T. per man, and for topslicing 8.2 T. per man. These stopes were not unduly hot, and there was not more than the usual amount of timber to interfere with the work of the men. The tonnages obtained per shoveler were considered low; first, because of a poor grade of Mexican labor, many of the men having come in from railroad grading camps; and second, because of a poor spacing of raises, especially in the top-slice stopes, where, in general, they were spaced 25 ft. by 66 ft. (7.6 by 20.1 m.) centers. The average wage per laborer shift was $2.67 during the year. It was thought, however, that even under these conditions the men were not producing the tonnage that they should, so, with the consent of the management, the writer undertook to determine how the general efficiency of the underground shoveling could be improved. No predetermined plan for conducting these experiments was arranged because we had no definite ideas as to the scope of the work or the number of elements into which the investigation would resolve itself, before all of its phases could be determined. We were sure, however, that any work that would thoroughly cover the ground would have to be in the nature of a systematic time study, combined with a course of instruction in correct shoveling methods and adequate and intelligent supervision of the work. Two or three companies in the Southwest have done some work to determine the proper shovel to be used undcrground, but so far as is known the work has been limited to equipping certain parts of their mines with a particular type and size of shovel and thereafter watching the cost and efficiency records. In each case it seems to have been the shovel that held the 21-lb. (9.5-kg.) load that gave the bcst results. Excepting personal communications from these companies, the only data available on scientific shoveling are contained in F. W. Taylor's book, "The Principles of Scientific Management," and D. J. Haucr's article, in The Contractor for March 29, 1918, "A Hundred Hints for Shovelers." This paper discusses and draws conclusions from several thousand time-study readings, taken both on the surface and in the mines for nearly a year. A sufficient number of readings were taken on each factor in the problem for the plotting of curves of the performances and to obtain accurate indices of the work to be expected from this class of labor. The work is not as complete in all of its details as we would like to havc it, because we were forced to stop the work temporarily, owing to the numbcr of men going into the National service and our inability to get others who could make time studies. The results obtained so far, however, have been of such a startling nature that we have decided to submit them at this time, subject to future modification. It is hoped, also, that a free discussion of this paper will lead to a disclosure of any errors that may have becn embodied and offer some valuable suggestions for the conduct of future work.

Jan 1, 1920

By A. S. Odeh

ABSTRACT A simplified model was employed to develop mathematically equations that describe the unsteady-state behavior of naturally fractured reservoirs. The analysis resulted in an equation of flow of radial symmetry whose solution, for the infinite case, is identical in form and function to that describing the unsteady-state behavior of homogeneous reservoirs. Accepting the assumed model, for all practical purposes one cannot distinguish between fractured and homogeneous reservoirs fram pressure build-up and/or drawdown plots. INTRODUCTION The bulk of reservoir engineering research and techniques has been directed toward homogeneous reservoirs, whose physical characteristics, such as porosity and permeability, are considered, on the average, to be constant. However, many prolific reservoirs, especially in the Middle East, are naturally fractured. These reservoirs consist of two distinct elements, namely fractures and matrix, each of which contains its characteristic porosity and permeability. Because of this, the extension of conventional methods of reservoir engineering analysis to fractured reservoirs without mathematical justification could lead to results of uncertain value. The early reported work on artificially and naturally fractured reservoirs consists mainly of papers by Pollard,l Freeman and Natanson,2 and Samara.3 The most familiar method is that of Pollard. A more recent paper by Warren and Root showed how the Pollard method could lead to erroneous results,4 Warren and Root analyzed a plausible two-dimensional model of fractured reservoirs. They concluded that a Horner-type pressure build-up plot of a well producing from a fractured reservoir may be characterized by two parallel linear segments. These segments form the early and the late portions of the build-up plot and are connected by a transitional curve. In our analysis of pressure build-up and drawdown data obtained on several wells from various fractured reservoirs, two parallel straight lines were not observed. In fact, the build-up and drawdown plots were similar in shape to those obtained on homogeneous reservoirs. Fractured reservoirs, due to their complexity, could be represented by various mathematical models, none of which may be completely descriptive and satisfactory for all systems. This is so because the fractures and matrix blocks can be diverse in pattern, size, and geometry not only between one reservoir and another but also within a single reservoir. Therefore, one mathematical model may lead to a satisfactory solution in one case and fail in another. TO understand the behavior of the pressure buildup and drawdown data that were studied, and to explain the shape of the resulting plots, a fractured reservoir model was employed and analyzed mathematically. The model is based on the following assumptions: 1. The matrix blocks act like sources which feed the fractures with fluid; 2. The net fluid movement toward the wellbore obtains only in the fractures; and 3. The fractures&apos; flow capacity and the degree of fracturing of the reservoir are uniform. By the degree of fracturing is meant the fractures&apos; bulk volume per unit reservoir bulk volume. Assumption 3 does not stipulate that either the fractures or the matrix blocks should possess certain size, uniformity, geometric pattern, spacing, or direction. Moreover, this assumption of uniform flow capacity and degree of fracturing should be taken in the same general sense as one accepts uniform permeability and porosity assumptions in a homogeneous reservoir when deriving the unsteady -state fluid flow equation. Thus, the assumption may not be unreasonable, especially if one considers the evidence obtained from examining samples of fractured outcrops and reservoirs. Such samples show that the matrix usually consists of numerous blocks, all of which are small compared to the reservoir dimensions and well spacings. Therefore, the model could be described to represent a "homogeneously" fractured reservoir. la this paper, the fundamental equation of flow

Jan 1, 1966

By Ralph A. Sherman, J. M. Pilcher

BY surface treatment of coal is meant the application of a material, either solid or liquid, to the surface of pieces of coal. The purposes of surface treatment are varied. They may be to identify or "trade-mark" the coal, to modify the burning characteristics, the coking tendencies, or the behavior of the ash, to prevent the freezing of wet coal, or to control the dust. The control of dust is the usual purpose of surface treatment. TRADE-MARKING COAL The application of color to the surface of coal for the purpose of identification and registration of the trade-mark has been practiced to some extent. In 1928, the Glen Alden Coal Co. began to color its coal and adopted the trade-mark, "Blue Coal." The Old Ben Coal Co. later followed a similar practice with "Green Coal." A commoner means of identification of coal has been the stenciling of designs or pasting labels on large lumps or in the distribution of small cardboard tags through the smaller sizes. The details of the method used to color coal have not been revealed. Usually all of the coal is not treated, because of the expense. Only enough pieces are colored to show clearly when distributed through the coal. The patent literature gives information on some of the methods proposed. Esselen and Weiss 1 have patented the deposition of a coloring material in the valleys of the surface of the coal. Sperr2 covers the quenching of coke with water containing a pigment or dye that will deposit on the coke. He also suggests electroplating with copper or nickel. Glinsmann 3 subjects the freshly fractured coal surface to the action of an alkali or alkali earth ferricyanide and a ferric salt. Barsky and Hanson4 specify a method for the application of the same chemicals covered by Glinsmann.

Jan 1, 1943

By R. A. Harrington

THE structure of anodic films formed on aluminum and other metals under varied conditions is not well known despite the wide use of such films both as protective coatings and as the dielectric medium in elec-trolytic condensers. The present work was undertaken as a survey of the possibilities of electron diffraction in the investigation of anodic films, especially in comparing the properties of anodic films formed under dif-ferent sets of conditions and subjected to various subsequent treatments. In addition, an effort has been made to compare surface films formed on aluminum by anodic treatment with surface films formed by heating, immersion in chemicals, etc, The electron diffraction method in many cases has been successfully applied to the study of thin surface films. Its principal advantage is that it can be used without removing the films from the base material upon which they have been formed. The low penetrating power of electrons, in the "reflection" diffraction method which has been used in this work, prevents the appearance of diffraction patterns from substances at depths greater than about 100 Angstrom units (10-6 cm.). Different investigations of the structure of anodic films have shown widely varying results, depending on the methods used in preparing the films. Apparently under some conditions these films are crystalline and under other conditions they are amorphous, and it has been difficult to say which type of structure will be found in any particular case. Schmid and Wassermann&apos;s&apos; X-ray diffraction patterns of eloxal? films show two broad, diffuse bands, which these investigators attribute to finely divided cubic y-Al2O3-§ Burgers, Claassen, and Zernicke3 obtained sharp X-ray

Jan 1, 1940

The saying that a "prophet" is without honor in his own country does not always hold true, as is shown by the following from one of the local papers, which appeared under the above heading: "Edwin Ludlow, for more than seven-years vice-president of the Le-high Coal.& Navigation Co., with headquarters in Lansford, has resigned, to take effect July 1, when he will take up his residence in New York and engage as a consulting engineer. Mr. Ludlow, during the incumbency of his present position, has demonstrated his efficiency as an engineer and general manager in many directions, notable among which are the almost perfect methods in practice in the inside workings of the several operations under his charge and the erection of the most complete, most practical and most commodious breakers for the preparation of the mine product for market. In addition, his relations with organized labor have been cordial and his dealings with its representatives have been invariably based upon the principle of fair play."

Jan 7, 1919

By Philip R. Whitney

Deposition of manganese oxides is of common occurrence in streams of the north-eastern United States. Manganese entering the stream in solution in ground water is oxidized and deposited in the stream, primarily as oxide coatings on detrital materials. Prevalence and thickness of the coatings increases with increasing particle size in the coarse sand and gravel range. A number of metals of economic and environmental interest are enriched in these coatings. Samples of 8 to 16 mm pebbles were obtained from two streams in the Shawangunk region of southeastern New York State, an area of know71 Pb/Zn/Cu mineralization. The pebbles were leached to remove the oxide coatings and the resulting solutions analyzed for Mn, Fe, Pb, Zn, Cd, Cu, Co, and Ni. Trace-metal/Mn ratios in these streams are generally one to two orders of magnitude higher than regional background values. Profiles of trace- metal/Mn ratios along the streams show considerable detail; contributions of metals from tributaries are sharply reflected in the metal content of the oxides. The potential advantages and disadvantages of using coated stream gravel for geochemical prospecting and environmental studies are discussed in the light of these and other data.

Jan 1, 1976

By Walter Miller

During no similar period in the development of petroleum refining technology has so much progress been made in methods and equipment for the economical utilization of heat. Drastically severe commercial and economical conditions controlling the refining industry during 1927 gave a great impetus to improved efficiency and more economical operation in all departments. I think it is fair to say, however, that more progress has been made in the department of heat utilization than in other branches. I use the word utilization advisedly in the dual sense of better primary generation and application of heat and of saving by recovery methods. It was because of this trend that the subject, "Economical Application of Heat," was made the keynote of the refinery engineering sessions just completed. No new, outstanding elemental discoveries can be claimed for the year along this line. Some of the progress made has been in the development of better furnaces and distilling equipment embodying the more modern principles of boiler practice in obtaining complete combustion of the fuel, low excess air requirements and high transfer rates through the heating surface. Transfer rates of 3000 to 6000 B. t. u. per sq. ft. per hr. were considered good some time ago in the older type of equipment. Today a transfer rate of 25,000 to 35,000 B. t. u. is an actual accomplishment in commercial installations and engineers are talking of the feasibility of 50,000, 75,000, even 100,000 R. t. u. per sq. ft. per hr. Contributing most to bringing this about have been the rational use of the velocity factor on both the oil and firing side of the heating surface, and the study and application of the principles of radiant heat in furnace design. Vapor Heat Economy The principle of heat exchange, especially against oil vapors, has been applied to a greater extent than ever before. The recovery of heat from oil vapors is not new. This was practiced 20 years ago or more in Europe,

Jan 1, 1928

By Edward P. Chapman

In the Leadville district toward the close of the "intermediate mesothermal period" of mineralization, there occurred a stage of ore deposition marked by a rather complex mineral association. As bismuth minerals formed in many places during this period, it is here called the "bismuth stage" for convenience of description. The minerals so far identified with this stage, listed roughly in the order of prominence, are: chalco-pyrite; several varieties of galena, differing slightly from one another in their small contents of silver, bismuth and tellurium; altaite; hessite; galenobismutite; alaskaite; aikinite; gold; tennantite; argentite; and perhaps sphalerite and arsenopyrite. With the exception of gold, the age relations of these minerals are difficult to determine. As shown in their descriptions, they all appear contemporaneous and hypogene. Gold may be in part contemporaneous, but most of it is distinctly later. Where minerals of this stage occur so that they can be mined alone, as at the Tucson mine, they constitute high-grade ore. Elsewhere their presence in small amounts has served to increase greatly the value of what otherwise would be low-grade pyritic or zinc-lead sulphide ore. The distribution of the bismuth ores corresponds closely to the distribution of gold ores, though not so general. It seems probable that most of the old in the district was deposited during the "bismuth stage." These ores occur relatively near the supposed centers of mineralization in Breece and Printer Roy Hills or deep down along the Tucson-Maid fault, which is one of the well recognized channels of mineralization in the Iron Hill and Graham Park areas. Consideration of the high-grade nature of this mineralization and the fact that it appears to be found relatively close to the source of mineralization suggests that prospecting along some of the known channels, even deeper than they have yet been prospected, may offer hope of commercial success. Introduction The Leadville district has been studied sinee 1880, and numerous detailed geologic descriptions of it are available in print; so also are more or less complete summaries of the mineral paragenesis, representing what was known at various periods up to 1927, the year of publication of Professional Paper 148.V lie writer has been engaged as consulting geologist at Leadville since the year 1926, and has been able to examine various types of Leadville ores throughout this period. Inasmuch as

Jan 1, 1941

By Edward P. Chapman

In the Leadville district toward the close of the "intermediate mesothermal period" of mineralization, there occurred a stage of ore deposition marked by a rather complex mineral association. As bismuth minerals formed in many places during this period, it is here called the "bismuth stage" for convenience of description. The minerals so far identified with this stage, listed roughly in the order of prominence, are: chalco-pyrite; several varieties of galena, differing slightly from one another in their small contents of silver, bismuth and tellurium; altaite; hessite; galenobismutite; alaskaite; aikinite; gold; tennantite; argentite; and perhaps sphalerite and arsenopyrite. With the exception of gold, the age relations of these minerals are difficult to determine. As shown in their descriptions, they all appear contemporaneous and hypogene. Gold may be in part contemporaneous, but most of it is distinctly later. Where minerals of this stage occur so that they can be mined alone, as at the Tucson mine, they constitute high-grade ore. Elsewhere their presence in small amounts has served to increase greatly the value of what otherwise would be low-grade pyritic or zinc-lead sulphide ore. The distribution of the bismuth ores corresponds closely to the distribution of gold ores, though not so general. It seems probable that most of the old in the district was deposited during the "bismuth stage." These ores occur relatively near the supposed centers of mineralization in Breece and Printer Roy Hills or deep down along the Tucson-Maid fault, which is one of the well recognized channels of mineralization in the Iron Hill and Graham Park areas. Consideration of the high-grade nature of this mineralization and the fact that it appears to be found relatively close to the source of mineralization suggests that prospecting along some of the known channels, even deeper than they have yet been prospected, may offer hope of commercial success. Introduction The Leadville district has been studied sinee 1880, and numerous detailed geologic descriptions of it are available in print; so also are more or less complete summaries of the mineral paragenesis, representing what was known at various periods up to 1927, the year of publication of Professional Paper 148.V lie writer has been engaged as consulting geologist at Leadville since the year 1926, and has been able to examine various types of Leadville ores throughout this period. Inasmuch as

Jan 1, 1941

By G. Rinelli, A. M. Marabini

Flotation of rutile with N-benzoyl-N-phenyl-hydroxyhmine (N-BPHA) has been investkated. Initially, floatability tests were performed in a Hallimond tube. The results indicated that rutile was floatable at pH 2-4 with N-BPHA concentration between 2 x 10-3 mol/L and 2 x 10-2 mol/L. Selectivity against hematite was recognized when operating at pH values below 2. Following the hypothesis of the formation of a surface chelate between N-BPHA and titanium ion, this compound was precipitated from a solution of Ti (SO4)2 to which N-BPHA was added. I. R. spectrometry of the rutile before and after treatment with N-BPHA solution confirmed the presence of this compound on the rutile surface. Adsorption isotherm and kinetics were determined by analyzing N-BPHA in solution with an U. V. technique. A hypothesis on the way N-BPHA is adsorbed on rutile is presented.

Jan 1, 1984

By Craig R. Barrett, Jack L. Lytton, Oleg D. Sherby

The types of substructures developed during high-temperature creep of (110)[001]-oriented polycrys-talline Fe-3.1 pct Si were examined by electroetching of dislocation sites. Edge dislocations were observed to accumulate adjacent to grain boundaries and poly-gonize perpendicular to their glide planes to form a "Pile-up" of nearly parallel tilt boundaries. The dislocation density developed within the grains during steady-state creep was found to increase with increasing stress. The formation of periodically spaced groups of edge dislocations along grain boundaries was observed, and it was proposed that these formed to relive bending stresses at grain boundary shear .faults. Grain boundary serrations developed at these faults, and it was suggested that this was a result of localized grain boundary migration at the polygonized groups. THE authors have conducted a series of high-temperature creep tests on (110)[001]-oriented poly-crystalline Fe-3.1 pct Si sheet. The creep specimens were examined at various stages of creep by means of electrolytic etching of dislocation sites using the chrome-acetic acid solution developed by Morris.&apos; Hibbard and Dunn2 have demonstrated that the etch pits produced with this technique correspond to single dislocations. It is the purpose of this paper to present and discuss the dislocation substructures which were formed during high-temperature creep at constant stress. EXPERIMENTAL PROCEDURES The polycrystalline Fe-3.1 pct Si sheet employed in this study contained a (110)[001] texture. This texture was quite strong, and the elastic properties of the sheet closely approached those of a single crystal of iron.3,4 A typical analysis in weight percent for this material is 3.1 Si, 0.1 Mn, 0.003 C,

Jan 1, 1965

By H. W. Gillett

Many of the parts of motor cars, aircraft, etc., that require strong light construction, hence must be made of high-quality steel, are stressed to the maximum limit only in a very small volume. In parts subject to bending stress a line or even a point may take the maximum stress. A series of endurance tests under repeated bending in progress in the U. S. Bureau of Mines laboratories, like similar tests by other investigators, has shown the great difference in life of sister bars of the same stecl, handled in the same way and tested at the same nominal stress. It is known that a surface notch or scratch greatly increases the local stress over the nominal calculated stress; internal notches, such as those formed by inclusions or sonims, probably have a similar effect. From the tetss made by the Bureau of Mines, the cleanliness of the steel at the dangerous section, or point of maximum stress, seems to be one of the most important factors in determining the life of the piece. The more localized the stress, the more does chance, rather than the average properties, dctermine the life of the steel. The usual test, a tension test of a bar taken longitudinally, is not sensitive to the local drop in strength (or tendency to increase the true local stress over the nominal) because of inclusions, which probably have a more injurious effect in hard heat-treated steels, such as must be used when great strength is sought, than in softer steels. Users of steel who make transverse tests find surprisingly low ductility on transverse bars of dirty steel, though the longitudinal tests may be good. Bending tests, reverse bending tests, and notch-bar impact tests,

Jan 1, 1923

By H. W. Gillett

Many of the parts of motor cars, aircraft, etc., that require strong light construction, hence must be made of high-quality steel, are stressed to the maximum limit only in a very small volume. In parts subject to bending stress a line or even a point may take the maximum stress. A series of endurance tests under repeated bending in progress in the U. S. Bureau of Mines laboratories, like similar tests by other investigators, has shown the great difference in life of sister bars of the same stecl, handled in the same way and tested at the same nominal stress. It is known that a surface notch or scratch greatly increases the local stress over the nominal calculated stress; internal notches, such as those formed by inclusions or sonims, probably have a similar effect. From the tetss made by the Bureau of Mines, the cleanliness of the steel at the dangerous section, or point of maximum stress, seems to be one of the most important factors in determining the life of the piece. The more localized the stress, the more does chance, rather than the average properties, dctermine the life of the steel. The usual test, a tension test of a bar taken longitudinally, is not sensitive to the local drop in strength (or tendency to increase the true local stress over the nominal) because of inclusions, which probably have a more injurious effect in hard heat-treated steels, such as must be used when great strength is sought, than in softer steels. Users of steel who make transverse tests find surprisingly low ductility on transverse bars of dirty steel, though the longitudinal tests may be good. Bending tests, reverse bending tests, and notch-bar impact tests,

Jan 1, 1923

By Arthur S. Dwight

We author of this historical chapter will perhaps be criticized for limiting his subject to the history of the blast furnace in lead smelting, and especially to the part it played in the great custom ore-smelting business which for three decades or more was the means of opening up vast mineral treasures and practically dominated the mining industry in the Rocky Mountain region of the United States, in Mexico and in Canada. The men of that era shared the romance and the thrills of mining, and bore their part as pioneers in the building of the great West. The present writer was too young to participate in the first of the three decades mentioned, but immediately thereafter came under the apprenticeship of some of the men who had worked out the early metallurgical problems of the industry, became personally acquainted with most of the others of that group, heard the tales of early experiences, successes and failures, the gossip of the frontier and mining camps, from all of which there remain embedded in his mind clear impressions of the outstanding personalities of that time. That is the background against which the fifty years of intimate contact with the mining and smelting business and his own experiences as metallurgist stand out in his memory, and it is hoped that the gentle reader may understand and approve his desire to rescue from comparative oblivion the fundamentally valuable results accomplished by these fathers of the industry. It will be the purpose of this chapter first to narrate the general history of the growth of the industry; second, to pay tribute to some of the pioneer metallurgists, and third, to discuss some of the salient points of the metallurgical practice at different periods, to illustrate the technical progress of the art. The series of eight Annual Reports of Rossiter W. Raymondl,† U. S. Commissioner of Mining Statistics from 1869 to 1876, contain most of the available information about the early smelting operations in the Rocky Mountain region, and much is in the early volumes of the Transactions of the American Institute of Mining Engineers. The monograph by S. F. Emmons2 though not published until 1886, contained an elaborate description of the smelting works operating in 1879. Otto H. Hahn3 wrote a valuable paper in 1883, on smelting prac-

Jan 1, 1937

By R. D. Groves, G. M. Potter, T. H. Jeffers

Experiments on ammonium carbonate leaching of native copper ores crushed to 1-inch size showed that in 30 days 55 percent of the copper was extracted from 0.7 percent copper conglomerate-type ore, and 85 percent was extracted from 2.1 percent copper amygdaloid-type ore. Cupric ions were not necessary to initiate leaching, and dilute solution containing only 2.2 grams per liter NH3 and 1.9 grams CO, was a suitable solvent. Copper was recovered from the leach liquor by solvent extraction and electrolysis of the strip solution. Cyclic testing of the leach-solvent extraction-electrolytic procedure is in progress on a 6-ton charge of minus 12-inch conglomerate-type ore assaying 2.2 percent copper. Oxygen is metered to the closed leach vessel as required by the leaching reaction. Initial copper dissolution was much slower than from minus 1-inch ore, but the leaching rate then markedly improved.

Jan 1, 1974

By AIME AIME

EVEN in the choice of his birthplace and parents, Donald B. Gillies indicated clearly the trend of his professional career. He was born on Nov. 4, 1872, at Bruce Mines, in Ontario. His father and mother came from the Isle of Skye, Scotland, to Nova Scotia, moved from there to Canada, and finally settled in the copper country in the northern peninsula of Michigan, where the senior Mr. Gillies followed mining as an occupation. Donald&apos;s early education was in the public schools and he graduated from Linden Lake (Mich.) high school in 1890. Following the family interest in mining he entered the Michigan Mining School, now Michigan College of Mining and Technology. There he was the rare student who excelled both in athletics and scholastic work. On the athletic field he was a crack football player and track roan. As early as 1890 lie established a record of 10 sec-

Jan 1, 1938

By Gail Moulton

THE oilfields in Illinois are located principally along the LaSalle anticline in the southeastern part of the state. The oil produced comes most largely from beds of Pennsylvanian and Mississippian age, but there is an increasing important production from deeper horizons, as will be noted under new development. The oil is largely of paraffin base, and has an average specific gravity of about 35° Baume. The rank of Illinois as an oil producer has dropped from third since 1913, when its production was exceeded only by that of California and Oklahoma, to eighth in 1923. This has been the result of failure to find new pools of considerable size to offset the declining production of the old wells and of the greatly increased production of some of the other states. The noteworthy features of petroleum production in Illinois during 1924 are: the low rate of decline for the state as a whole; the smaller percentage of dry holes; and the larger average initial yield of the new wells.

Jan 3, 1925

By Frank Ittner

In this section it is proposed to discuss operating methods considered good practice under the various field conditions commonly encountered. Efficient field direction and types of equipment needed to meet transportation problems are considered only to the extent that the desire to produce the best possible records must sometimes give way to the factor of cost. As in all engineering projects, alternative possible methods of operation must be considered in the light of relative costs as well as of the quality of results obtained, Cost may be in the background of much that is done in the field operations, but only the effect on record quality will be considered here. Record quality at a particular shot point may vary with the various factors of spread character (relative positions of geophones and shot point), shot-hole depth, formations opposite position of shot, size of charge, the effect of repeat shots, surface geology and culture in the immediate vicinity of the geophones, recorder instrument characteristics, particularly filter.

Jan 1, 1940