Search Documents

By James W. Halley

' FINE-GRAINED " steels have been standard products for many years. This paper describes an investigation of the effects of some of the more common grain-growth; inhibitors used to produce these steels. The properties, response to heat-treatment, and the deoxidation practice necessary to produce "fine-grained" steels have been the subjects of numerous papers. It has been shown that a substantial quantity of' aluminum is necessary to produce this type of steel, and it has been indicated that titanium and zirconium produce a similar result. For some time there was a lively argument between those who felt that aluminum refined the grain and those who felt that aluminum oxide was the effective agent. This argument subsided with an apparent victory for those promoting aluminum oxide. Most of the work on grain size has divided steels into two broad classifications based upon McQuaid and Ehn's original carburizing test at 1700°F. or some similar test at this temperature. If the steel coarsened at this temperature, it was coarse grained, while if it did not it was fine grained. Quantitative data concerning how much a certain amount of aluminum raised the coarsening temperature and affected the properties, all other factors being constant, are very meager. Similar information regarding titanium and zirconium is practically nonexistent. The published information on aluminum yields some quantitative information. Epstein, Nead and Washburn' gave the first quantitative information on the amount of aluminum necessary to prevent grain growth at 1700°F. They showed that the addition of a pound to a pound and a half of aluminum per ton (0.05 to 0.075 per cent) would assure steel that would not .coarsen during a McQuaid-Ehn test at 1700°F. Herty, McBride and Hough2 reported that a steel containing 0.020 per cent acid-soluble aluminum coarsened between 1742° and 1832°F., while steels containing 0.016 per cent and 0.017 per cent acid-soluble aluminum coarsened between 1652~ and 1742°F. compared with similar aluminum-free steels that started to coarsen at 1580°F. Herty3 also showed a marked improvement in low-temperature notched impact resistance with increasing acid-soluble aluminum up to 0.030 per cent. McQuaid4 compared the coarsening of steels containing 0.011 to 0.204 per cent total aluminum and found a maximum coarsening temperature at 0.098 per cent aluminum. He had no samples between 0.015 and 0.098 per cent aluminum. Houdrement5 found a marked decrease in coarsening temperature with aluminum contents above 0.50 per cent. Kinzel, Crafts and Egan6 found that aluminum and zirconium improved thy low-temperature impact resistance of a low-alloy steel, while titanium was detrimental. Sims7 shows that sulphur increases the coarsening temperature and that the maximum coarsening temperature is between 0.04and 0.06 Per cent added aluminum. The

Jan 1, 1946

By H. Souder

The object of this paper is to bring to the notice of engineers a safety detonating fuse by the use of which misfires in blasting may be eliminated and safety in blasting operations promoted.

Jan 1, 1915

By C. S. Cole

CO-CHAIRMAN CARTER S. Cole l-The stimulus of war definitely increases interest in the subject we are discussing at this Symposium. There have been, in the past, other symposia on this subject and there probably will be still others in the future, but I feel sure that this one will go down as one of the most important that have ever been held on the subject. In 1918 A.S.T.M. held a Symposium on Stress- Corrosion Cracking that was confined entirely to brass, because at that time few people were interested in the phenomenon as it applied to other metals. Again under the stimulus of war, we are gathered to discuss the subject, but this time brass alone is but part of our interest. It is interesting to note more papers on brass will be presented than there were in the 1918 session, but these brass papers, you will also note, comprise less than half our program. Aluminum, magnesium and

Jan 1, 1945

By C. A. Wert

THE solid solubility of cementite in a-iron has been investigated a number of times and there is now general agreement on the solubility of about 0.018 wt pct at the eutectoid temperature, 720°C. With decreasing temperature, the solubility falls off so rapidly and to such a low value that no data obtained by standard metallurgical methods are available below 500°C. Using a new technique, however, Dijkstral has obtained apparently accurate solubilities down to 400°C; which data agree well with previously measured solubilities in the 600" to 700°C temperature range.' The present paper has in part the purpose of extending his work to still lower temperatures. Earlier work of Low and Gensamer3 on iron has established that the presence of a relatively small amount of carbon can play a tremendous role in affecting the mechanical properties. In particular they found that the yield point remained high as they reduced the amount of carbon in the iron; the yield point dropped only after the carbon content had fallen to something less than 0.003 wt pct, the point where their carbon analysis failed. It seemed desirable to the present author to see if some means could not be found to extend this part of their work. This investigation has then the additional purpose to determine the range of carbon concentration in which the major change occurs. Solubility The method used in the present work to measure small percentages of carbon in a-iron utilizes internal friction. Since this method may not be fa-miliar to the reader, the following explanation will be given (a part of this procedure is from unpublished results of Dijkstra): It is known that the internal friction associated with the diffusion of

Jan 1, 1951

By Arthur Gray

THE thermal analysis of a metal or alloy is ordinarily made with the aid of heating and cooling curves, in which transitions are indicated by the rapid changes in curvature that accompany .changes in the rate of heat absorption or evolution. Analysis by the method that depends on the change in thermal expansivity is not customary, partly, at least, because of the difficulties involved in making the necessary measurements. However, under certain circumstances, the dilatometric method of analysis may possess advantages over the thermometric method that will justify the additional trouble required. The addition of 1 per cent. of zinc to an alloy has been found to produce, upon the volume changes that take place during transition, effects that suggest the possibility of using the dilatometric method of thermal analysis as a rather sensitive means of obtaining chemical information. Although the illustrations presented in this paper are drawn from data obtained during an investigation of dental amalgams, similar phenomena can doubtless be observed with other alloys. Some of the results found during an investigation made in 19171 have been confirmed by data on the thermal expansivity of amalgams published by Souder and Peters of the Bureau of Standards in reporting tests of dental materials.2 Although the Bureau of. Standards made experiments for the purpose of discovering effects of including zinc as one of the constituents of a dental alloy-a matter much discussed in dental literature but without the presentation of reliable experimental evidence to support the views of ;either side-the reports of the test made by the Bureau give the impression that certain striking phenomena associated with the presence of zinc were not noticed. Among such phenomena are those connected with the conditions that determine whether or not a specimen of amalgam becomes covered with droplets from which crystals develop.

Jan 9, 1920

Jan 1, 1934

By Michael D. Martin

Pima Mining Co., managed and 50% owned by Cyprus Mines Corp., with Union Oil of California and Utah Construction and Mining Co. sharing equally in the remaining 50%, is a medium-sized open pit copper mine situated in the very active Twin Buttes mining district, 22 miles southwest of Tucson, Ariz. In 1965, a three-part paper described Pima's growth from 3,000 tpd (tons per day) in 1957 to 18,000 tpd nine years later. Within months of the completion of the last stage of this sixfold expansion, studies were being wound up on a further major expansion, this time to 30,000 tpd. This expansion is now a reality. Details of the enlargement of the crushing and concentrating plant have already been covered in a recent paper, and the present paper will cover pit engineering studies, equipment selection, and current operating practices. Key factors in top management's decision to go ahead with the latest expansion were: (1) a substantial increase in ore reserves coupled with an appreciable decrease in grade, (2) a generally favorable outlook for copper prices, and (3) better than expected performance by mine and mill equipment purchased for the expansion to 18,000 tpd. For the pit design studies, particular attention was paid to pit stability, a problem area at times in the past, and to the location and grades of the final ramp systems. In drawing up the long-term mining schedule, the attitude of the ore, with the higher grade material lying deeper, was a critical factor and considerable stockpiling of lower-grade material in the early years had to be accepted in order to keep the annual grades close to the average of the orebody. The expansion called for major purchases of mine equipment in order to gear up the mine for delivery of 30,000 tpd to the concentrator. In general, equipment chosen was of types already proven at Pima, al- though there were some exceptions to this practice. One of these excep-

Jan 1, 1969

By B. W. Levinger

THE system Ti-CI- has been studied by several investigators." ' Though titanium and chromium are completely miscible at high temperatures, an intermediate phase of the approximate atomic proportions TiCr, has been identified at various compositions between 60 and 68 wt pct Cr. The structure of this phase was established as the cubic C15 (MgCu2) type with 24 atoms per unit cell and a lattice parameter 6.929 kX.2 During a study of the ternary system, Ti-Mo-Cr,5 the existence of a high temperature modification of the TiCr, phase was discovered. In a series of alloys annealed at 1300°C and containing from 60 to 70 wt pct Cr and 5 pct Mo, a new phase was present which did not correspond to either ß solid solution or TiCr,. By trial, the new phase was identified to be of the hexagonal C14 (MgZn2) structure with 12 atoms per unit cell. Further work showed that the hexagonal structure was. in fact, also present in binary Ti-Cr alloys quenched from high temperatures. To make the identification more certain, the intensities of the various reflections were calculated assuming a composition TiCr2 and C14 structure. Table I lists reflection planes, interplanar distances, calculated intensities, and a comparison of these values with the lines of a binary Ti-Cr alloy (66 pct Cr) annealed for 20 min at 1385°C and water quenched. Since high angle lines were more diffuse, the correspondence between visually observed and calculated intensities was not as good at these angles. Lattice parameters were computed to be a = 4.922 kX, c = 7.945, c/a :- 1.614. The corresponding interatomic distances are: titanium to titanium distance, 3.00:, kx, chromium to chromium distance, 2.43, kX, titanium to chromium distance, 2.88,, kX. These compare to 3.00, 2.45, and 2.87 kX in the cubic phase, respectively.' The atomic positions in the C14 structure are as follows: Titanium 1/3, 2/3, Z; 1/3, 2/3, 1/2: 2/3, 1/3, i; 2/3, 1/3, (1/2-z); Chromium 0, 0, 0: 0, 0, 1/2; 2x, 2, 1/4; 232, x, %; X, 22, 1/4; X, 2x, 3/4; x. x, 1/4; x, x, 3/4; The values of x and z were calculated for the alloy mentioned and found as follows: z — 0.061, x = 0.165. The values assumed in the intensity calculations were those for an ideal close-packed lattice or z = 1/16, x = 1/6. Work in the Ti-Mo-Cr system indicates that y2 the hexagonal modification of TiCr2, is the stable phase above 1300°C, while y1 with the cubic structure is stable below 1000°C. X-ray examination of a number of alloys annealed at intermediate temperatures showed that the hexagonal and cubic phases can coexist. Alloys quenched from 1000°C and annealed at 1100" and 1200°C showed small amounts of y2 at the higher temperature. A considerable amount of y, seemed present, however, in cast alloys annealed at 1100°C. It further appears that there is a small but definite solubility range for both phases in the ternary system. Acknowledgment The results of this paper represent work carried out in conjunction with a project sponsored by Watertown Arsenal, Contract No. DA-11-022-ORD-272. References 'M. K. McQuillan: Journal Inst. Metals (1951) 79, p. 379. 2 P. Duwez and J. L. Taylor: Trans. ASM (1952) 44, p. 495. W. J. Van Thyne,. H.. D. Kessler, and M. Hansen: Trans. ASM (1952) 44, p. 974. 1 F. B. Cuff, N. J. Grant, and C. F. Floe: Trans. AIME (1952) 194, p. 848; Journal of Metals (August 1952). Unpublished Research, Armour Research Foundation. "H. J. Wallbaum: Ztsch. Krist. 103, p. 391.

Jan 1, 1954

The United States Employment Office of the Department of Labor, of which the division of engineering and education, under the direction of A. H. Krom, maintains an office at 29 La Salle Street, Chicago, Ill., is engaged in a classification of engineers in order to make their services more readily available in case of need. We have received a form used by this division, on which it requires only a very little time to indicate one's particular line of work, his experience and the salary that he desires. We have been asked to impress upon members of the Institute the distinct advantages that come through registration. Filling out the blank entitles an engineer to free employment service, provides him with direct contact with the Government, supplies him with information in regard to engineering affairs, and helps him to become successful in his profession. The Government wishes every technical man to register, so that it may know the strength and location of the engineering reserve. It is therefore the duty of every patriotic engineer, whether he needs a position or not, to register at once. Blanks can be obtained by addressing the office above noted.

Jan 10, 1918

By R. M. Murray

Although blister copper has been produced at the Mount Lyell Mining and Railway Company's works since 1896, it is only during the past five years that electrolytic refining has been undertaken locally, this having been done previously at customs refineries, at first in the United States, and afterwards at Port Kembla, New South Wales. Left to right: smelter building, converter building, blower building (in which converter-generators are housed), tank house and anode dock. Wire-bar furnace building in background at center. Possessing a hydroelectric power plant capable of generating power considerably in excess of the requirements of its mines and works at the time, the company was in a favorable position to undertake its own refining work, provided this advantage was not offset by the high cost of coal, which would have to be imported from the mainland, and provided also that the capital cost of the plant would not be unduly large in regard to the relatively small amount of copper to be treated. A study of these several conditions led to the adoption of a high-density plant using blister-copper anodes and equipped with an electric boiler to provide any

Jan 1, 1934

By J. B. Newkirk

IN 1939 Bitter and Kaufmann1 suggested that iron, precipitating from a copper-rich, Cu-Fe solid solution, appears initially as coherent particles of r-Fe which transform to the body-centered-cubic form of iron when the alloy is cold worked. Since then there has been considerable discussion, supported only by indirect evidence, regarding the validity of the concept. For example, Reekie, Hutchison, and Hether-ington2 interpreted the changes in electrical resistance accompanying the aging of Cu-Fe specimens in terms of a coherent 7-Fe precipitate which transformed to the incoherent a-phase during long aging or cold working. Greninger- ound that Cu-Fe alloys which had been water quenched from 1050" and then held at 650°C for 3 hr changed from weakly to strongly ferromagnetic as the aged wire was subsequently cold worked. He also found diffraction lines corresponding to body-centered-cubic iron in Debye-Scherrer patterns given by aged and worked specimens but lines corresponding to only one face-centered-cubic phase in specimens which had been aged but not worked. Knoppwost,' and later Cech and Turnbull,5 found that aged Cu-Fe specimens showed a slight increase in ferromagnet-ism after they had be? cooled in liquid nitrogen. Very recently Denney6 followed the kinetics of the precipitation reaction as indicated by the saturation magnetization, hardness, and diffuse X-ray effects. The experimental results reported by all of the authors mentioned above are readily explained in terms of the Bitter and Kaufmann concept. However, most of the evidence is indirect when used to define the structural changes involved. It was the aim of the present investigation to determine the mechanism of precipitation of iron from a Cu-Fe solid solution in the light of available published information and with additional new and more direct experimental data. Experimental Method At 1060°C copper will contain up to 3 atomic pct Fe in equilibrium solid solution.7 The solvus slopes rapidly toward lower iron concentration, so that at 600°C only about 0.5 pct Fe remains in solution at equilibrium. Below the eutectoid temperature (850°C), the iron-rich phase in equilibrium with the copper-rich solid solution consists of body-centered-cubic a-Fe. Above 850 °C the equilibrium iron-rich phase is face-centered-cubic r-Fe. The alloy to be studied was made by melting electrolytic iron and OFHC copper by induction under vacuum in an Alundum-lined crucible. The metal was held molten for about 5 min, after which time the power was turned off and the crucible was tipped about 70" to promote directional solidification. The resulting ingot, containing 2.5 wt pct Fe by analysis, was clean, large grained, and free of gross segregation. Slices % in. thick were cut from the ingot, rolled to 1/8 in. in thickness, homogenized in hydrogen at 1060°C for 24 hr and, finally, quenched in cold water. Specimens for all subsequent tests were made from these slices. Squares measuring about 1 cm on a side were cut from the slices to make specimens for studying hardness and microstructure. Wires (0.020 in.) for the Debye-Scherrer survey were drawn from 1/8 in. sq rods which had been cut from the homogenized slices. Large crystals for observing diffuse X-ray diffraction effects were prepared by mechanically

Jan 1, 1958

By Felix Wunsch

WHILE the effect of the cold-junction temperature has been known by many, its consideration has been ignored in a number of installations, resulting at tunes in a very considerable error. In fact, the magnitude of this error may amount to over 100° in some cases. While hand-operated correcting devices for portable checking pyrometers may be entirely satisfactory, it is, of course, desirable to have such apparatus en¬ Millivoltmeter Thermocouple Platinum Wire Mercury FIG. 1.-EARLY `METHOD OF AUTOMATICALLY COMPENSATING FOR COLD-JUNCTION TEMPERATURE CHANGES. tirely automatic, when applied to curve-drawing or printing pyrometers, otherwise there is no assurance that the record is correct. Numerous methods for automatically compensating for cold-junction temperature changes of thermocouples have been proposed and used in connection with millivoltmeters. One of the earliest proposed was that shown in Fig. 1. A bare resistance wire was immersed in a column of mercury located near the cold junction of the thermocouple. An increase in temperature near the cold junction resulted in a rise of the mercury column, which short-circuited more of the resistance wire causing an increase in the potential difference across the millivoltmeter, which compensated for the decreased electromotive force of the thermocouple.

Jan 9, 1919

By R. L. Lloyd

UNLIKE the development of sintering lead, copper and zinc ores, the sintering of fine irony material had its birth, not as a result of gradual growth along lines aimed at the production of sintered and agglomerated product, but because the success of the sintering operation in other lines had been brought to the attention of the ironmasters, who were immediately attracted by the prospect of being able to convert their own fines-into a similar product. The abundance of iron ores in the United States and their comparative cheapness had led iron men into the habit of not paying particular attention to the fine material blown out of their blast furnaces. Hundreds of thousands of tons had been stacked up and used only during times of shortage of ore and then usually without any preliminary preparation, though many attempts had been made to briquette it. Briquettes proved good material, but the operation of briquetting was too expen-sive when applied to iron-ore fines. The development of the iron-ore blast furnace in the United States tended toward large units, high columns and heavy blast pressure, and this tendency is still peculiar to this country, whereas in the other countries the tendency has been to smaller units, lower columns and lower blasts. The high blast pressures and swift driving of the American blast furnace tend, of course, to produce more flue dust than European practice, and this production of flue dust was augmented when large quantities of soft ore, of which the Mesabi is typical, came on to the market. These ores are desirable chemically but physically they are soft, friable and fine, and when they are used in the iron blast furnace the flue dust produc-tion is increased. The necessity of rehandling the flue dust lead to briquetting on an extensive scale. The binders used were either chemical or mechanical, and in one system the briquettes were kiln fired in very high temperatures. Rotary kilns, coal or oil fired, were used extensively, and gave a product of hard and more or less nodulized material, but at considerable cost. This was the situation in regard to iron flue dust when the late James Gayley and his associates became interested in the idea of sintering the iron blast-furnace flue dusts under their own fuel (included coke dust) of which they carried between 15 and 30 per cent.

Jan 10, 1922

By C. A. Siebert, S. H. Bush

Isothermal temper-embrittlement studies were conducted on a 5140 steel at various temperatures for times as long as 3000 hr. Specimens from the embrittled steel were subjected to impact tests, metallographic examination, microhardness, and lattice-parameter measurements. SEVERAL of the steels in the low alloy group are subject to a pronounced decrease in impact energy if held within, or cooled slowly through, a range of temperatures below the lower critical. This phenomenon, known as temper embrittlement, is quite pronounced in the chromium steels of which AISI 5140 is typical. This study considered the response of one heat of 5140 steel when embrittled isothermally at various temperatures for times as long as 3000 hr. Excellent reviews of the work done in the field of temper embrittlement have been written by Hollomonl and Woodfine.' Both authors list the various theories which have been advanced to explain temper embrittlement. Some of the mechanisms considered were: 1—a transformation below 700°C; 2—an allotropic modification of iron; 3—precipitation from the ferrite of such compounds as carbides, nitrides, phosphides, or chromium oxides; 4—decomposition of retained austenite; 5—modification of special carbides; 6—grain-boundary segregation; and 7—selective distribution of carbides. The present study investigated the changes in hardness, Meyer's number, impact properties, micro-structure, and lattice parameter which occurred on embrittlement. Previous studies considered the influence of microstructure and of prior austenitic grain size3 on the response of 5140 steel to temper embrittlement. Equipment and Procedure All samples were taken from one heat of 5140 steel; the chemical composition of this steel was: 0.43 pct C, 0.86 pct Mn, 0.020 pct P, 0.019 pct S, 0.27 pct Si, 0.84 pct Cr, 0.10 pct Ni, 0.06 pct Mo, 0.10 pct Cu, and the remainder Fe. The material was received as % in. rounds. This stock was cut down to blanks measuring approximately 0.425~0.425~2.196 in. Heat Treatment: The rough blanks were normalized at 1600°F (870°C) for 1 hr, then austenitized at 1600°F (870°C) for 1 1/2 hr, and quenched into an agitated oil bath. The specimens were tempered at 1275°F (690°C) for 5 hr and water quenched. These tempered specimens were designated as the toughened state. Embrittling Treatments: The tempered bars were divided into sets and subjected to the various embrittling treatments listed in Table I. Temperatures from 750" to 1050°F were investigated for times of 1 to 3000 hr. Special tests to determine the effect of heating a short time at a higher temperature after long-time embrittlement at some lower temperature were also conducted. All specimens were water quenched at the end of the embrittling cycle, then ground and notched to obtain standard Charpy V-notch specimens. Impact Tests: The bars were fractured in a 260 ft-lb Charpy impact unit; specimens were fractured at temperatures ranging from —315°F to room temperature. Fixed temperatures used consisted of —315°F with liquid nitrogen, —115°F with dry ice and acetone, and 32°F with ice and water. Intermediate temperatures were obtained by suspending the bars in a jig over the liquid nitrogen, dry ice and acetone, or ice and water.

Jan 1, 1955

By T. D. Yensen

In the investigation of the magnetic properties of iron-nickel alloys,' it was found necessary in order to make the alloys forgeable, or malleable, to add small quantities of some other element. Iron-nickel alloys have been known for nearly a century, but have been made in commercial quantities only since 1885. Their remarkable mechanical properties were disclosed by Riley in 1889 and from that time on a large amount, of research work has been done both to discover new properties and to correlate the results obtained.2 Lately the Bureau of Standards has collected the published data in a special circular" giving in compact form an account of the properties of the iron-nickel alloys. It also contains a clear historical sketch of the development as well as a selected bibliography. The chief difficulty with the development of iron-nickel alloys was that the "pure" alloys do not forge readily. The addition of small amounts of manganese, however, made the alloys forgeable, and manganese has therefore come to be regarded as a necessary constituent of nickel steels. The present paper shows to what extent manganese is needed for various nickel contents and also what is the effect of other alloying elements on the forgeability. It also touches upon the cause of forgeability but refers to other sources for more exhaustive treatises on the subject. The alloys were prepared by melting electrolytic iron and electrolytic nickel with or without other alloying elements in the desired proportions in a magnesia crucible in a vacuum furnace under a pressure of 1 mm. mercury. The ingots, weighing about 2 kg., were allowed to cool in vacuo. If pipes or blowholes were present, the ingots were cut in such

Jan 1, 1922

By T. D. Yensen

In the investigation of the magnetic properties of iron-nickel alloys,' it was found necessary in order to make the alloys forgeable, or malleable, to add small quantities of some other element. Iron-nickel alloys have been known for nearly a century, but have been made in commercial quantities only since 1885. Their remarkable mechanical properties were disclosed by Riley in 1889 and from that time on a large amount, of research work has been done both to discover new properties and to correlate the results obtained.2 Lately the Bureau of Standards has collected the published data in a special circular" giving in compact form an account of the properties of the iron-nickel alloys. It also contains a clear historical sketch of the development as well as a selected bibliography. The chief difficulty with the development of iron-nickel alloys was that the "pure" alloys do not forge readily. The addition of small amounts of manganese, however, made the alloys forgeable, and manganese has therefore come to be regarded as a necessary constituent of nickel steels. The present paper shows to what extent manganese is needed for various nickel contents and also what is the effect of other alloying elements on the forgeability. It also touches upon the cause of forgeability but refers to other sources for more exhaustive treatises on the subject. The alloys were prepared by melting electrolytic iron and electrolytic nickel with or without other alloying elements in the desired proportions in a magnesia crucible in a vacuum furnace under a pressure of 1 mm. mercury. The ingots, weighing about 2 kg., were allowed to cool in vacuo. If pipes or blowholes were present, the ingots were cut in such

Jan 1, 1922

By George S. Koch

We have devised a multivariate statistical model useful to interpret data from exploration geochemistry and also pertinent for the analysis of data from petrology, paleontology, and other geological fields. The model is applied to several simulated cases in order to compare anomaly recognition by inspection and by quadratic regression.

Jan 1, 1977

By Donald W. Petrasek

The effects of selected alloying elements on the elevated-temperature tensile properties of copper alloy -tungsten fiber reinforced composites were invcstigated. A cornparison of the elevated-temperature tensile properties of copper alloy - tungsten fiber reinforced composites, representing soluble systems. was made with copper - tungsten fiber reinforced composites, representing a mutually insoluble system. A linear relation between tensile strength and volume percent fiber content existed at elevated temperatures for all the systenzs investigated. The copper alloy composites were weaker in tension at high volume percent fiber contents than copper composites in which alloying with the fiber did not occur. The tensile strength of the alloyed tungsten fiber decreased with increasing penetration of the alloying element into Ihe tungsten fiber. THE technique of combining strong fibers with relatively weak matrix materials so that the fibers are load-carrying members has been utilized for many years in the reinforcement of plastics with glass fibers. This type of strengthening is currently being extended to include the reinforcement of metals with metallic fibers. Investigations of the room-temperature tensile properties of metal-fiber-reinforced metallic composites have been numerous,'-" but the study of tensile properties at elevated temperatures has been limited. In previous work done at the Lewis Research Center' composites consisting of mutually insoluble constituents were investigated. Composites were made of copper reinforced with uniaxially oriented tungsten fibers. The stress-strain behavior and tensile properties of the composites were related to the tensile properties of the base materials. The tensile strength of the composite was directly proportional to the volume percent of tungsten fiber present, and the full strength of the fiber was realized. Few metal fiber - metal matrix systems exist that are mutually insoluble, and those that do exist are not generally practical. An extension of this work was an

Jan 1, 1967

By Martin F. Milligan

THIS short discussion of the effects of deoxidation on the mechanical properties of cast steels is intended to serve as general introduction to the subject of this afternoon's session. The subject is covered in detail in Mr. Carter's excellent paper. My material has been collected from the works of various investigators, several of whom are present today. For a definition of deoxidation, as applied to steel-furnace melting practice, we can best go to Briggs' book, "The Metallurgy of Steel Castings." Briggs says that deoxidation "includes all the phenomena in the final preparation of steel that would permit it to solidify free from gas cavities and from dissolved oxygen of all kinds." Various practices are used by welters to produce these end results.

Jan 1, 1947

By T. E. Leontis, D. H. Feisel

MAGNESIUM alloys containing rare earth metals have received considerable attention during the past several years because of the need for light alloys having high strength and creep resistance at elevated temperatures. Although much of the work reported earlier has dealt with alloys containing Mischmetal, it has been shown in two previous papersl, V hat distinctly different effects are produced by various rare earth metals and rare earth metal mixtures on the properties of magnesium. For example, much higher strengths are obtained in magnesium alloys containing didym-ium (essentially neodymium plus praseodymium) than in alloys made with Mischmetal, which contains all the rare earth metals in the proportions in which they occur naturally in the monazite ore. Mg-rare earth metal alloys are characterized by a relatively coarse grain size, which greatly impairs castability. The addition of zirconium as a second alloying ingredient has been shown8,7 to refine the grain size, which also produces a distinct improvement in the strength properties. Certain Mg-Mischmetal-Zr and Mg-Mischmetal-Zn-Zr alloy compositions which are currently being produced commercially have been discussed in dytail by Nelson and Strieter,8,4 who also present some in- formation on a Mg-low Ce-Mischmetal-Zr alloy, and by Nelson.8 A patent issued to Jessup, Emley, and Fisher9 emphasizes the superiority of Mg-didymium-Zn-Zr alloys over the corresponding alloys made with Mischmetal. The purpose of this paper is to present the results of an extensive investigation concerned with the effect of increasing amounts of zirconium on magnesium sand casting alloys containing several different rare earth metal mixtures in varying amounts. The effect of the addition of zinc to some of these alloys is also being reported. Preparation and Testing of Alloys The alloys studied in this investigation were prepared in small laboratory melts according to the melting procedures described by Nelson1" as the Crucible Method. Electrolytic magnesium having the composition shown in Table I was used as the starting material. The rare earth metal alloying ingredients used in preparing these alloys were essentially of the compositions listed in Table 11. Some of the didymium-containing alloys were prepared using a Mg-didymium hardener. The rare earth metal content of this hardener analyzed 1.2 pct Ce, 10.4 pct Pr, 80.8 pct Nd, and 7.6 pct La. The zirconium was added in one of three forms: 1) as sponge zirconium obtained from the Bureau of Mines; 2) as a fused salt consisting of 50 pct ZrCl, and 50 pct alkali chlorides from which the zirconium is reduced by the magnesium; or 3) as a Mg-Zr hardener. The alloying procedures and melt hand-

Jan 1, 1958