Search Documents

By Edward Richardson

As DEVELOPED up to the end of the Great War, an airplane was essentially a mechanism of wood and fabric, joined and held together by metal fittings and, fastening. The engine and accessories, wire for wheel spokes and other tension members, and the occasional use of metal for interplane struts and the shafts of surface controls required some metal, but essentially it was a. wood and fabric structure. Attempts had been made to use metal for other purposes, such as struts in the drag-trussing of wing panels and for short interplane struts, and Junkers had produced an airplane of iron in 1915. By 1917 he was using steel tubes and duralu-min sheets, securing noteworthy advantages aerodynamically and from the standpoint of weigh PRINCIPLES OF AIRPLANE CONSTRUCTION The loaded weight of airplanes ranges from 500 lb. for the light plane of which we heard so much a short time ago, to about 40,000 lb. The great majority of planes range from 2000 to 10,000 lb. Of this weight from 15. to 30 per cent. is for the dividend-earning load. This percentage is so low that every per cent. saved on the rest of the weight increases the pay load from 3 to 6 per cent. The economic value of every pound that can be saved in designing or constructing a plane is sufficiently great to warrant spending money on refined methods of structural analysis, materials of superior strength properties for a given weight, methods of manufacture which may make possible the use of refinements in structural design, and the like, to an extent unknown heretofore.

Jan 1, 1928

By Roland W. Rammler

With oil consumption increasing more rapidly than known reserves in industrial countries, there has been a growing interest in the production of synthetic crude oil. The main starting materials for such production are coal, oil shale and tar sand, all of which occur in enormous quantities in North America. A process sequence suitable for all three of these starting materials incorporates a preliminary retorting step to produce oils for subsequent hydrotreating. For this retorting step, a technique known as the Lurgi-Ruhrgas process has proven highly efficient. The process has been commercially used for the flash carbonization of coal and has also been tested in pilot- plant experiments with oil shale and tar sand.

Jan 1, 1970

By H. C. Gatos, A. D. Kurtz

WITH the growing interest in the mechanism of self-diffusion of metals, the study of accurate and convenient methods for determining self-diffu-sion coefficients appears highly desirable. It was with this objective in mind that the present investigation was undertaken. Gatos and Azzam1 employed an autoradiographic technique for measuring self-diffusion coefficients of gold. This method involved sectioning of the specimen through the diffusion zone and recording the radioactivity directly on a photographic film. Because of the very short range of the emitted ß rays in gold, the activity recorded on the film was essentially the true surface activity. With proper choice of the sectioning angle, sufficient resolution could be obtained and the entire concentration-distance curve recorded in one measurement. For the boundary conditions of the experiment, where an infinitesimally thin layer of radioactive material diffuses in positive and negative directions into the end faces of a rod of infinite length, the solution of the diffusion equation is C/Cn = 1/v4pDt exp (-x2/4Dt) where C is the concentration of diffusing element (photographic density in this case), C,, is the constant (depending upon amount of radioactive material), x is the diffusion distance, D is the diffusion coefficient, and t is the time. Thus, by plotting the logarithm of the concentration vs the square of the diffusion distance, a straight line results and the slope contains the diffusion coefficient. In this manner, the self-diffusion coefficient of gold can be obtained as a function of temperature. In the present investigation the results reported by Gatos and Azzam1 have been verified, and the autoradiographic technique has been further developed and applied for the determination of the self-diffusion coefficient of gold at a number of temperatures. Furthermore, the energy of activation for the self-diffusion of gold has been conveniently determined. . Experimental Techniques Preparation of Specimens: The inert gold of high purity was received in the form of a rod from which cylinders were cut and machined to a diameter of 0.500 in. The specimens were annealed to a suitably large grain size and the faces were surface ground prior to the deposition of the radioactive layer. The radioactive isotope Au198 was chosen. It was produced in the Brookhaven pile by means of the reaction Au197 + n ? Au108. It decays by ß emission (0.96 mev) to Hg108 with the subsequent emission of a y ray (0.41 mev). 70Au 108 ? 80Hg 108 + -1e°. The half life of the Au108 is 2.7 days so that a strict time schedule had to be maintained in order to secure sufficient activity until the end of the experiments. For this reason, initial activities as high as 10,000 millicuries per gram were used. The gold arrived in the form of foil and was evaporated onto one face of each gold specimen cylinder to a thickness of about 100A. A sandwich-type specimen was formed by welding two such cylinders together. Evaporation of Gold: The gold was evaporated under vacuum from heated tantalum strips which were bent in such a way as to limit the solid angle through which the gold was allowed to vaporize, thus insuring a more efficient utilization of the gold. The specimens rested on flat brass rings which had an inner diameter of 0.475 in. The entire specimen-holding assembly could be manipulated from outside the vacuum system by means of a magnet which attracted a slug of soft iron attached to the assembly. By evaporating inert gold on glass slides under conditions identical to those employed for the radioactive gold, it was found that the thickness of the films was about 100A. Welding: The welding was performed by hot pressing in a stainless steel cylinder. The inside of the cylinder was threaded and fitted for two plugs. The specimens to be welded were placed in the middle of the cylinder and two pressing disks, one at each end, were inserted to avoid shearing stresses as the plugs were tightened. Mica disks were placed between the pressing disks and the specimens to prevent them from welding. The plugs were then tightened with a hand wrench and the entire unit was placed in an argon stream for about an hour to remove the oxygen. The unit was then inserted in the center of an argon atmosphere furnace maintained at about 700°C and left there for about an hour. Because of the difference in the temperature coefficient of expansion of the two metals, as the temperature rose. the pressure on the specimen-rollple increased and a weld resulted Welding was generally satisfactory under the conditions described.

Jan 1, 1955

By Herbert Wilson

THIS topic was discussed at the meeting in St. Louis in September, 1917, and at the meeting in New York in February last, but in the interval the war has accentuated in measurable degree the necessity for considering human relationship, not only as between nations, or in the treatment of our returning soldiers, but with respect to the relations between labor and capital in industry. It is my firm conviction that no other subject will have so large a place in industrial and political life during the next decade as this. Heretofore, the employer has been so engrossed with the financial, mechanical, and technical aspects of his business that he, has been willing to muddle through 'his relations with labor as best lie might and, on the other hand, the laborer has been so engrossed in his endeavors to secure a livelihood under whatever living and working conditions might be offered him that he has given little thought to his relations to his employer, until some misunderstanding has ended in disagreement and strike. No thinking man doubts that were the machinery available for friendly, personal, face-to-face consideration of the problems confronting employer and employee, there would he fewer disagreements, fewer strikes, and a better and more settled industrial situation. The necessity for some such medium for exchange of views has resulted in the organization of labor and, in some measure, of capital. Each party, engrossed only in defending its own viewpoint, has generally tried to gain its point by might rather than by right. Gradually, however, the representatives of both elements are beginning to appreciate that when the machinery for bringing them together in friendly communion is available their differences frequently settle themselves. There remain yet vast numbers of employers and of employees who are not organized and to whom the opportunity of friendly discussion of differences is not available; for these the machinery should he provided.

Jan 1, 1919

By J. L. Rodda

THE desirability of a uniformly sized abrasive for metallographic polishing has probably been recognized in a general way for a long time. Certainly all metallographers have recognized the damage that can be done to a polished surface by a piece of grit, especially if one of the softer metals, such as zinc or aluminum, is being polished. It is to be doubted, however, whether many metallographers have had any adequate idea of the particle size of the abrasives they were using or of the range of sizes encountered in any given grade of abrasive. At any rate, the descriptions of abrasives for metallographic work found in the literature are generally very meager. It was with the idea of securing an abrasive with a limited range of particle size that a study of this problem was commenced. Commercial abrasives, even when recommended for metallographic work, are made up of particles of varying sizes. One such abrasive contains some particles so fine that they remain in suspension for days and other particles so coarse that they settle at the rate of 3 in. per minute. It is evident that the coarsest particles are over 100 times the diameter of the smallest ones, or over 1,000,000 times the volume. The hopelessness of avoiding scratches under these conditions is evident. Vanderwilt1 has described a laboratory method for grading abrasives in which the elutriator is used. Le Chatelier's method, described by Goerens,2 also makes use of an elutriator. However, the elutriator is too slow for this purpose and requires too delicate a control for the range of sizes desired. The method of stirring up the abrasive in water, allowing it to settle for as given time, then drawing a measured depth off the top of the suspension, has been finally adopted as the simplest proce-dure. The largest particle in a given portion is. then determined by Stokes' law:3

Jan 1, 1931

By W. T. Isbell

IN the Parkes process of lead refining, after desilverization has been completed by means of the addition of zinc, there remains in the lead from 0.5 to 0.6 pct zinc. At this stage in the refining operations virtually all impurities are reduced to refined lead specifications except zinc and antimony. All excess copper, nickel and cobalt have been removed by the zinc additions. The silver remaining should not exceed 0.1 oz per ton. It then remains only to remove the zinc and antimony in order to produce refined lead. At the Herculaneum plant of the St. Joseph Lead Co., practice formerly was to complete the refining by means of oxidation in a reverberatory furnace. This process consisted of heating the lead to 14000 to 1500°F and allowing it to come in contact with excess air passing over the surface of the lead and periodically agitating the bath of lead with air. This procedure not only resulted in the loss of zinc but of a considerable quantity of lead converted to the oxide in the form of dross and fume. The fume, collected in the baghouse, together with the dross was returned to the blast furnace, thus adding appreciably to the circulating load on the blast furnace and refinery. In addition, operation and maintenance of the reverberatory furnace was expensive and required the performance of disagreeably hot and somewhat hazardous work. The process of dezincing with high vacuum was developed at this plant as a substitute for the oxidation process and finally led to lower operating costs, the practical elimination of dross and fume and the direct production of metallic zinc, which is very suitable for re-use in the desilverization process. Essentially this process consists of subjecting the lead to high vacuum, in a kettle provided with means for heating, a bell-shaped member open at the lower end so constructed that it can be immersed in the molten lead, and means for evacuating the interior of the bell and for sealing an agitator. Metallic zinc is thus produced and collects on the upper cooled part of the bell member. This metallic zinc is periodically removed and re-used in the desilverization process. The process is quite simple. It is conducted at a low temperature, thus permitting the use of iron equipment, and shows a material saving in refining costs over the old method. EQUIPMENT AND ITS USES Dezincing Machine.-The equipment employed in this process consists of a dezincing machine, a steel kettle of 120 tons capacity, a vacuum system and equipment for handling the dezincing machine (Fig I). The dezincing machine consists of a compact assembly, suitable for handling with an overhead crane, consisting of a treating chamber and the agitating mechanism. Treating Chamber.-The treating cham¬ber is a bell-shaped shell (4), similar in shape to a hemispherical kettle with a lid

Jan 1, 1947

By Marshall Pease, R. J. Brandon

A UTILITY that has a large consumption of coal must insure an adequate and sound supply of fuel. The Detroit Edison Co., which has an annual coal consumption of about four million tons and spends approximately $32 million a year for coal, including freight charges, has developed a program for fuel procurement and for evaluation and selection of fuel for reliable and efficient plant operation. Fuel Procurement Coal Purchasing Division: The Fuel Supply Div. of the Purchasing Dept. combines all of the procurement functions in one group, which must maintain adequate stocks of fuel. In addition to its usual purchasing duties, the division also governs transportation, follow-up, invoice and freight bill, in cooperation with the Accounting Dept. The Fuel Div. is comprised of the fuel agent, an assistant fuel agent, a coal buyer and five coal clerks, who follow the movement of each car, initially approve freight bills and invoices, and file claims whenever there is a shortage of one ton or more. The fuel agent reports directly to the purchasing agent of the Company, and all major programs are planned jointly with the chief purchasing officer. The apparent individuality of the fuel section is necessary because of the tremendous volume of coal cars handled each day, sometimes as many as 500, which must be handled promptly to complete the fastest possible move from the mines to the plants. Determining Annual Coal Volume: Through the combined studies of a Production Dept. Load Committee and the Controller's office, accurate predictions of coal requirements for any given year are provided the Fuel Dept. from 12 to 15 months in advance. This is divided into the requirements of all individual power plants and central heating plants. This in turn determines the quantity and quality for plants whose specific fuels vary with the type of equipment installed. In the Detroit area, which has a high industrial load, early estimates of annual coal consumption usually are resolved at the end of the year within 4 or 5 pct of the original plan. Operating in a highly developed industrial area eases the task of estimating primary output; and, with the residential demands increasing in a steady and fairly well-defined pattern, the overall coal schedules are not subject to radical changes during any given year. Selecting Suppliers: At any time, but especially during or before an emergency, the coal supply factor must be made secure. This is particularly true in the procurement of utility fuel. There are always extreme quantities of so-called "bargain" coal available during the buyers' markets, such as recently prevailed. These opportunistic offerings may be considered a means of averaging down overall price, rather than as a steady and dependable supply source. Coal is purchased on contract from mine operators and sales agents who have proved reliable. They are not opportunists who desert for higher dollars in times of duress; they do not fail to fulfill contracts when markets rise or overship when markets dip. The progressive operator today who is willing to expend capital to improve quality and service deserves much more consideration than a matching of short-term pennies. When a company has a high volume of annual needs, all phases of the mine supply must be considered. The mine must be able to produce the quality required at a fair price and be able to sell oversizes of coal in enough volume to screen sufficient nut and slack. It must crush coal and sell mine run at prices in line with competitive nut and slack and be willing to do so when there is no demand for prepared sizes. Determining Price: The public utility is in direct competition with any of its customers who can, if savings are guaranteed, generate their own power. Today, to a greater extent than ever before, private industry must do a better overall job than Government-controlled operations. The price of coal must be realistically balanced with the price paid by almost all industries and the railroads as well. The supply-demand ratio in coal is not difficult to discern. There is access at all times to Govern-

Jan 1, 1952

By P. J. Clifford, A. B. Brown

The development of computerised mine planning has been hindered by the cost of processing the large data bases associated with mineral deposits and the inherent inconvenience of performing an interactive process on a time-shared computer. A dedicated computer is ideally suited for the purpose but reasonably priced micro/mini-computers have not had the capacity to store the volume of data or the processing capability required. Hardware development has cleared the way for the development of truly interactive mine planning software, covering the complete range of activities associated with mine planning, from geological assessment to short-term scheduling of operations, incorporating them into a single system using a common database. The integrated system, comprising software and dedicated hardware, adds previously unattainable speed, flexibility and clarity to the planning process because it has been tailored exclusively for that purpose.

Jan 1, 1983

By V. C. Perini

The North Central Texas district as herein defined includes the counties of Brown, Callahan, Coleman, Comanche, Coryell, Eastland, Erath, Fisher, Hamilton, Haskell, Hood, Jones, Lampasas, Mills, Nolan, Palo Pinto, Parker, San Saba, Shackelford, Stephens, Stonewall, Summer-ville, Taylor, Throckmorton and Wise. These counties as listed are the counties of District 7B, State Railroad Commission. In the new designation of districts for the Transactions, the North Central Texas district includes most, but not all, of the counties of the previously classified West Central Texas district. This district covers the south central crest and the west flank of the Bend flexure north of the Llano uplift. The west flank of the Bend flexure is on the east boundary of the Permian Basin of West Texas. The greater part of the oil and gas produced in this district has been from Pennsylvanian strata. Some oil and gas has been produced from the lower Permian (by the latest, selection of the Pennsyl-vanian-Permian boundary) and minor amounts from the Mississippian and Ordovician sediments. Increasingly important quantities of oil and gas are to be expected from the older sediments by deeper development in proven fields and by new discoveries. Most of the oil and gas in the district has accumulated in localized, well-defined structural traps in limestone and sandstone reservoirs and in traps due to stratigraphic changes in sedimentation, mainly porosity traps in limestone and sandstone lenses, both usually associated with some structural feature. These features are found by surface and subsurface geological structural mapping, by core drilling and by geophysical surveying. Geochemical methods are also the basis for some wildcatting. The demand for sweet crude oil from this district is firm for local and national consumption, but the market price for the oil remains practically the same as in 1941. The price is not adequate to meet the requirements of the average independent operator with the continued advance in production, tievelopment and wildcatting costs. Stripper wells are being plugged daily and should be jealously saved for the future local and national reserves, especially in view of the fact that new discoveries of commercially important oil and gas reserves are not keeping pace with consumption. An expected economic disruption attendant upon the national war effort has arisen and continues in the future outlook for this district. The lack and delay of securing replacement parts for almost all oil-field equipment has handicapped and delayed operations and has decreased efficiency in wildcatting, development and production. Sufficient experienced drilling, scientific and office personnel is lacking because of inductions in the armed forces and migration to war industries during the period before manpower conservation became effective. The office personnel of the average oil and gas producer continues to be swamped by the increasing demands for reports by state and federal bureaus. An average of IQ days

Jan 1, 1944

By V. C. Perini

The North Central Texas district as herein defined includes the counties of Brown, Callahan, Coleman, Comanche, Coryell, Eastland, Erath, Fisher, Hamilton, Haskell, Hood, Jones, Lampasas, Mills, Nolan, Palo Pinto, Parker, San Saba, Shackelford, Stephens, Stonewall, Summer-ville, Taylor, Throckmorton and Wise. These counties as listed are the counties of District 7B, State Railroad Commission. In the new designation of districts for the Transactions, the North Central Texas district includes most, but not all, of the counties of the previously classified West Central Texas district. This district covers the south central crest and the west flank of the Bend flexure north of the Llano uplift. The west flank of the Bend flexure is on the east boundary of the Permian Basin of West Texas. The greater part of the oil and gas produced in this district has been from Pennsylvanian strata. Some oil and gas has been produced from the lower Permian (by the latest, selection of the Pennsyl-vanian-Permian boundary) and minor amounts from the Mississippian and Ordovician sediments. Increasingly important quantities of oil and gas are to be expected from the older sediments by deeper development in proven fields and by new discoveries. Most of the oil and gas in the district has accumulated in localized, well-defined structural traps in limestone and sandstone reservoirs and in traps due to stratigraphic changes in sedimentation, mainly porosity traps in limestone and sandstone lenses, both usually associated with some structural feature. These features are found by surface and subsurface geological structural mapping, by core drilling and by geophysical surveying. Geochemical methods are also the basis for some wildcatting. The demand for sweet crude oil from this district is firm for local and national consumption, but the market price for the oil remains practically the same as in 1941. The price is not adequate to meet the requirements of the average independent operator with the continued advance in production, tievelopment and wildcatting costs. Stripper wells are being plugged daily and should be jealously saved for the future local and national reserves, especially in view of the fact that new discoveries of commercially important oil and gas reserves are not keeping pace with consumption. An expected economic disruption attendant upon the national war effort has arisen and continues in the future outlook for this district. The lack and delay of securing replacement parts for almost all oil-field equipment has handicapped and delayed operations and has decreased efficiency in wildcatting, development and production. Sufficient experienced drilling, scientific and office personnel is lacking because of inductions in the armed forces and migration to war industries during the period before manpower conservation became effective. The office personnel of the average oil and gas producer continues to be swamped by the increasing demands for reports by state and federal bureaus. An average of IQ days

Jan 1, 1944

By J. M. Flaitz, A. S. Parks

OF the various methods of sampling gas-condensate wells, a method that secures a continuous representative sample of the well stream is desirable. Such a method, consisting of a sampling tube introduced into the well tubing, has proved satisfactory. The method is sufficiently accurate for operating and engineering problems. A portable testing apparatus can be used with the sampling tube to obtain data useful in studying the economic and technical aspects of the development and operation of gas-condensate properties. INTRODUCTION The recent discovery and development of gas reserves that contain hydrocarbons that condense with reduction of temperature or pressure, or both, to form a product known as condensate, has brought many new problems to the oil and gas industries. With further discovery of deep, high-pressure fields it is presumable that many more gas fields of this type will be added to the steadily increasing number. Such gas reserves are found either associated with oil as a gas cap or in separate formations. There seems to be no positive correlation between the physical or geological nature of the reservoir, and the chemical composition or phase characteristics of its contents. Knowledge of the chemical make-up and phase behavior of gas-condensate reserves are needed to cope with many problems. A knowledge of the chemical composition and phase characteristics of the reservoir material is necessary to properly design a gasoline or recycling plant, to estimate natural gas and condensate reserves, to enable the operator to study the economic and technical aspects of various methods of operation and development, and to carry out the plan of operating subsurface and surface lease equipment. This information is often useful in questions of mineral ownership, proration, legal position, and taxation. It is the purpose of this paper to discuss methods used by the writers to determine the chemical composition and phase characteristics of the fluids produced from a condensate well. The scope of the paper includes a discussion and description of the method of sampling, the results of tests on the accuracy of the sampling method, a description of a portable testing apparatus used to examine the phase characteristics, typical results of tests on wells from several condensate fields, and some of the applications of these data to production problems. References to previous work on this subject are cited at the end of the paper. THE PROBLEM At reservoir conditions of temperature and pressure, the fluids produced from a condensate well exist in a homogeneous vaporous condition. The consequent reduction of temperature and pressure that occurs as this gas enters and flows up the well tube results in condensation of some of the hydrocarbon material to form a liquid. The relative amount of liquid condensed at any point in the flowing system

Jan 1, 1941

By F. W. Davis

This paper deals in a general way with certain of the necessary requirements of refractories for the open-hearth furnace. The refractories in common use for the different parts are discussed both as to the service they are giving and their suitability to withstand existing chemical, thermal and physical requirements. The relation between the service and allowable cost of a refractory is discussed and suggestions are requested on these points. The purpose of this paper is not to report, to the Institute, the results so far obtained in the survey, by the Bureau of Mines, of the metallurgical requirements for open-hearth refractories, but to present an outline that we hope will serve as a basis for discussion. The systematic survey that the Bureau proposes to make has not been outlined, although considerable preliminary work has been done in the way of interviewing open-hearth superintendents in several of the larger steel plants from the Chicago district eastward. At the several conferences so many of the opinions were diametrically opposite, when considering the same point, that it was thought that such an opportunity as the Institute offers in the way of a clearing house for moot metallurgical topics should not be overlooked. For this reason, the paper has been prepared as a basis for a discussion which, it is believed, will be of value in outlining the program of the Bureau. D. A. LYON, Assistant Director. THE importance of securing suitable refractories for metallurgical operations is daily becoming more universally recognized; particularly in the manufacture of open-hearth steel, where the life and earning power of the furnace depends largely on the judgment and care exercised in the selection of the correct quality of refractory for each of the parts. Any innovation that would make available to the steel manufacturers refractories with longer life or better suited to their needs than those now employed, and at a cost that would permit of their use, would be of enormous value to the industry at large. It is quite probable that revolutionary changes would not be necessary. Material now used in some parts of

Jan 3, 1924

By B. E. Morgan, C. K. Dumbauld

The need for a low-strength cementing composition for use in well cementing is reviewed and results are presented of laboratory and experimental field tests of a modified cement having a controlled ultimate tensile strength of approximately 200 psi. The modified cementing composition may he prepared from either high early strength or normal portland cements by the addition of bentonite clay and a suitable agent for dispersing and controlling the set of the slurry. Substitution of the modified cement for conventional slow-set cements may give better completion results in many wells because the modified cementing composition has lower set strength, lower slurry density, and greater slurry stability than conventional cement slurrieh. The lower ultimate strength allows greater penetration with less shattering of the set cement when perforating casing and cement. The lower elurry density allows the placement of longer columns of cement slurry, and the greater slurry stability reduces the possibility of having an uncemented section caused by the settling of cement particles before the cement set.. INTRODUCTION High strength lias always been one of the accepted criteria of a good cement. During the early use of portland cement in well cementing. emphasis was placed upon securing cements with higher strengths. In 1931, Barkis' reported that, "Normal oil well cements have been improved to develop greater strengths and uniformity of product, which has aided in producing successful jobs in cementing the deeper strings." As long as most wells were completed by the open-hole method. the use of cements having high strengths seemed desirable, and there was no objection raised against high-strength cementing compositions. For a number of years. how-ever, the industry has been completing a large numher of wells by setting and cementing casing through productive horizons and then obtaining production by gun-perforating the section of casing opposite the desired interval. Although this method has been generally successful, difficulties have been experienced in some cases in completing or recompleting wells because of apparent lack of adequate penetration by the bullets through the casing and surrounding sheath of cement and into producing formation. In addition to the penetration trouble: there have been indications that fracturing and shattering of the set cement by perforating might he a contributing factor in causing the failure of some jobs to exclude water or gas from oil producing zones. The possibility that cements having high set strengths were contributing to til difficully ill obtaining satihfartory perforating results has re. ceived attention during recent years. Gun perforating tests conducted in 1944 showed that the depth of bullet penetration into set cement varied with the hardness of the cement, the greater the strength of the cement the less being the penetration. In 1946, Farris2 pointed out that high strength cements were not needed in well cementing, and in 1947, data published by Oliphant and Farris3 showed that set cement was perforated without shattering at approximately 150 psi tensile strength. whereas at approximately 300 psi tensile strength severe cracking and shattering occurred. Oliphant and Farris suggested that wells be perforated at the proper time interval after placement of the cement so that the set cement would have the desired strength. Several difficulties may he encountered in trying to perforate a cement job at the correct time to catch the tensile strength near 150 psi. The rate of strength development of different cements varies considerably. This fact is illustrated by results of tensile strength measurements presented in Fig. 1. These data show that at 175°F the tensile strengths of three conventional slow-set cements varied from 75 to 235 psi at the end of 12 hours. After 24 hours, the tensile strengths varied from 200 to 455 psi. The rate of strength development is affected. also. by the temperature of the forniation, and this adds to the uncertainty of perforating at the rorrect time, since accurate well cementing temperatures may not he known in many cases. Furthermore, in the recomple-tion of wells it is sometimes necessary to perforate cement which has set for a long period and has developed maximum or final strength. In view of the apparent need for a cementing composition having a controlled ultimate strength, an investigation was

Jan 1, 1951

By C. K. Dumbauld, B. E. Morgan

The need for a low-strength cementing composition for use in well cementing is reviewed and results are presented of laboratory and experimental field tests of a modified cement having a controlled ultimate tensile strength of approximately 200 psi. The modified cementing composition may he prepared from either high early strength or normal portland cements by the addition of bentonite clay and a suitable agent for dispersing and controlling the set of the slurry. Substitution of the modified cement for conventional slow-set cements may give better completion results in many wells because the modified cementing composition has lower set strength, lower slurry density, and greater slurry stability than conventional cement slurrieh. The lower ultimate strength allows greater penetration with less shattering of the set cement when perforating casing and cement. The lower elurry density allows the placement of longer columns of cement slurry, and the greater slurry stability reduces the possibility of having an uncemented section caused by the settling of cement particles before the cement set.. INTRODUCTION High strength lias always been one of the accepted criteria of a good cement. During the early use of portland cement in well cementing. emphasis was placed upon securing cements with higher strengths. In 1931, Barkis' reported that, "Normal oil well cements have been improved to develop greater strengths and uniformity of product, which has aided in producing successful jobs in cementing the deeper strings." As long as most wells were completed by the open-hole method. the use of cements having high strengths seemed desirable, and there was no objection raised against high-strength cementing compositions. For a number of years. how-ever, the industry has been completing a large numher of wells by setting and cementing casing through productive horizons and then obtaining production by gun-perforating the section of casing opposite the desired interval. Although this method has been generally successful, difficulties have been experienced in some cases in completing or recompleting wells because of apparent lack of adequate penetration by the bullets through the casing and surrounding sheath of cement and into producing formation. In addition to the penetration trouble: there have been indications that fracturing and shattering of the set cement by perforating might he a contributing factor in causing the failure of some jobs to exclude water or gas from oil producing zones. The possibility that cements having high set strengths were contributing to til difficully ill obtaining satihfartory perforating results has re. ceived attention during recent years. Gun perforating tests conducted in 1944 showed that the depth of bullet penetration into set cement varied with the hardness of the cement, the greater the strength of the cement the less being the penetration. In 1946, Farris2 pointed out that high strength cements were not needed in well cementing, and in 1947, data published by Oliphant and Farris3 showed that set cement was perforated without shattering at approximately 150 psi tensile strength. whereas at approximately 300 psi tensile strength severe cracking and shattering occurred. Oliphant and Farris suggested that wells be perforated at the proper time interval after placement of the cement so that the set cement would have the desired strength. Several difficulties may he encountered in trying to perforate a cement job at the correct time to catch the tensile strength near 150 psi. The rate of strength development of different cements varies considerably. This fact is illustrated by results of tensile strength measurements presented in Fig. 1. These data show that at 175°F the tensile strengths of three conventional slow-set cements varied from 75 to 235 psi at the end of 12 hours. After 24 hours, the tensile strengths varied from 200 to 455 psi. The rate of strength development is affected. also. by the temperature of the forniation, and this adds to the uncertainty of perforating at the rorrect time, since accurate well cementing temperatures may not he known in many cases. Furthermore, in the recomple-tion of wells it is sometimes necessary to perforate cement which has set for a long period and has developed maximum or final strength. In view of the apparent need for a cementing composition having a controlled ultimate strength, an investigation was

Jan 1, 1951

By W. Blaschke, E. Malysa

INTRODUCTION In recent years in Poland, a problem connected with the occurrence of a considerable amount of liberated galena grains in size fractions under 1mm has arisen in the zinc-lead processing area. Operating practices have included crushing of ore particles under 0.2 mm followed by flotation. Jigs were applied to separate the concentrates from size fractions under 10 mm and to prevent the galena overgrinding. However, the fractions being too wide, the jigs have not worked effectively, in spite of the great differences in specific gravities of galena, blende and gangue minerals. Fine galena grains move into light fractions in considerable amounts and hence are overground. Therefore, the flotation becomes difficult and galena is lost in its tailings. These losses could be avoided by introducing separation in the grinding and classification circuits. The amount of 0-1 mm fraction is great; therefore, the application of concentrating tables or other kinds of jigs is impossible from an economic point of view. Taking these factors into account, the possibility of application of pinched-sluices was investigated. These are simple devices without moving parts, they have a high output for the unit areas, and their water and energy consumptions are low. In this paper, the results of zinc-lead ores beneficiation in pinched-sluices are presented.

Jan 1, 1980

By William J. Gillich, Gerald L. Moss

PREVIOUS studies of the shock loading of randomly oriented polycrystalline aggregates have firmly established that, after rather short load duration, hydrostatic compression closely approximates the shocked state.' However, McQueen deduced from pressure measurements with good time resolution that, during shock loading, metals begin to undergo a stress relaxation at the yield stress. He suggested that the relaxation is due to plastic deformation accompanying the change from a one-dimensional compression to a three-dimensional, hydrostatic, compression.' Stress relaxation may occur faster as stress is increased above the yield stress, but the existence of unidirectionally compressed states for finite times suggests that the concept of a unidirectionally distorted lattice should furnish considerable insight into the mechanical behavior of materials subjected to shock loading. Here, a crystallographic analysis is presented for the hypothetical situation where atom motion may be considered as unidirectional which, as indicated above, is a useful extension of the macroscopic concept of shock loading to the microscopic domain. Only motion caused by the com-pressive forces is treated; i.e., lattice vibrations upon which this motion is superimposed, as discussed by Fitzgerald, are ignored.3 The purpose of the analysis to be presented is to develop a description for single crystals of the lattice rotations that occur for idealized uniaxial strain deformation. The usefulness of such an analysis in realistic deformation is to give a method of specification of those properties of an initially distorted lattice which would affect the subsequent deformation. Non-axial complications that arise experimentally, such as off-axis rarefaction waves, must be treated in proper context. Consider the material element shown in Fig. 1 and let the compression be uniform at all regions of the element. Then, any interior point of the element is displaced in proportion to its distance from the base of the element. Accordingly, if the top of a unit element is displaced by an amount, (-K), with respect to the base, a point P(X, Y) will be displaced by (-KY). Crystal planes are, therefore, rotated by the compression. Analysis of this rotation may be accomplished from the geometry shown in Fig. 1 where the line OP is the edge of the plane {hkl} and N is its normal. The orientation of the crystal plane with respect to the shock direction is specified by the angle, before deformation. After deformation the edge of plane {hkl}

Jan 1, 1969

By W. C. Schroeder

During the post-war period, and particularly during the past few years, coal production has been maintained at a reasonably constant level. This is in contrast to the greatly expanded demand for oil and natural gas. Certain markets for coal, such as the railroad and for home heating, have tended to decrease, but this decline has been offset by an increase in demand for other uses, particularly for electric power. Since the United States has very large reserves of coal and relatively limited reserves of natural gas and oil, from the conservation viewpoint, it would be better if the increased demand were to fall more heavily on coal. Where coal has lost certain markets, the decision has not always been made on the basis of price, and, in fact, in many instances, the markets have been lost where coal could show a price advantage. There are various reasons for this situation but it can be attributed in the main to the preference of certain consumers for the convenience offered by liquid and gaseous fuels. In the production of chemicals such as benzene, phenol, or ammonia, coal still plays an important role. As co-products from coke-oven operations, a wide variety of aromatic chemicals are available. In recent years, however, the production has not been sufficient to supply the demand, and it is not profitable to build coke ovens to make chemicals unless there is a market for the coke as well. As a result, the petroleum industry is beginning to take a stronger part in the production of aromatic chemicals. Natural gas has almost displaced the coke-oven water-gas machine for the production of hydrogen for the synthesis of ammonia, as well as for the synthesis of methyl alcohol and other oxygenated compounds. This information is not new and is given here only as a basis for the discussion of the broad significance of the development of the gasification process. It is clear that if coal is to regain some of its old fuel markets, as well as to maintain a position in the field of chemical synthesis, processes must be available for converting coal to the type of fuel the customer wants, and for a cheap method of furnishing gaseous raw material to the chemical industry. The operation of coke ovens and water-gas machines is not the answer to this problem for at least two important reasons: (1) the limited supply and relatively high price of good coking coals, and (2) the relatively high costs of the combined operations of coking and manufacture of water gas.

Jan 1, 1953

By Frank A. Herald

Through the generous cooperation of the authors of the papers in this chapter, a great wealth of fundamental data is being made available. The same plan of securing and submitting data will be carried forward next year, with the hope of making a nearer approach to complete presentation of the data contemplated in the plan. In order to conserve space, we are printing below such footnotes as have general application to Table 1 in the papers in this chapter: Footnotes to Column Headings Table I In areas where both oil and gas are produced, unless gas is marketed outside the field, such areas are included in column headed "Oil." Manufacture of casinghead gasoline and carbon black is interpreted as outside marketing of gas. Production per acre is determined by dividing into the number of barrels of oil the sum of the number of acres assigned to "Oil" plus such number of acres of the total assigned to "Oil and gas" as represents the portion thereof occupied by oil. Wells producing both oil and gas are classified as "Poducing oil only" unless gas from them is marketed off the lease. W. water; G. gas; A, air. Bottom-hole pressures are preceded by "e." All other figures represent pressures at casinghead with well closed. P, paraffin; A, asphalt; M, mixed. 0 Cam, Cambrian; Ord, Ordovician; Sil, Silurian; Dev, Devonian; Mis, Mississippian; MisL, Lower Mississippian; MisU, Upper Mississippian: Pen. Pennsylvanian; Per. Permian; Tri, Triassic; Jur. Jurassic; CreL, Lower Cretaceous; CreU. Upper Cretaceous; Eoc, Eocene; Olig, Oligocene; Mio. Miocene; Pli. Pliocene. 6, sandstone: SH, sandstone, shaly; Ss, soft sand; H, shale; L, limestone; LS, limestone. sandy; C, chalk; A, anhydrite; D, dolomite; Da. arkosic dolomite; GW, granite wash; P, serpentine. Figures are entered only for fields where the reservoir rock is of pore type. Figures represent, ratio of pore space to total volume of net reservoir rock expressed in per cent. "Par" indicates that the reservoir rock is of pore type but said ratio is not known by the author. "Cav" indicates that the reservoir rock is of cavernous type; "Fis," fissure type. A, anticline; AF, anticline with faulting as important feature; Af, anticline with faulting as minor feature; AM, accumulation due to both anticlinal and monoclinal structure; H, strata are horizontal or near horizontal; MF, monocline-fault; MU, monocline-unconformity; ML, monocline-lens; MC, monocline with accumulation due to change in character of stratum; MI, monocline with accumulation against igneous barrier; MUP, monocline with accumulation due to sealing at outcrop by asphalt; D, dome; Ds, salt dome; T, terrace; TF, terrace with faulting as important feature; N, nose; 9, syncline. Information will be found in text as indicated by symbols: A, name of author, other than above. who has compiled the data on the particular field; C, chemical treatment of wells; G, gas-oil ratios; P, proration; U, unit operation; R, references; W, water; 0. other information.

Jan 1, 1934

By Clarence Claghorn

ONE of the simplest and most easily effected steps toward mechanization and concentrated mining in coal mines is the substitution of transport or room conveyors for the customary tracks in rooms, thus bringing the coal to the cars instead of taking the cars to the coal. As this involves little or no change in the established room and pillar layout, it appeals to the conservative operator who is more or less fearful of changes in system involving the element of roof con-trol. An increasing number of these room conveyors would seem to attest the favorable commercial results secured. Rooms are naturally driven as wide as roof conditions permit, providing maximum tonnage from each room cut. If the rooms are more than 12 to 14 ft. in width the room conveyor is usually set along one rib, a porta-ble face conveyor being set along the face itself and within easy shoveling distance of it, so arranged as to discharge to the transport conveyor. As the room ad-vances the latter is lengthened and the face conveyor moved up laterally. The advantages of this layout are, briefly, low lifts, no shoveling, no waiting for cars. It gives easy shovel-ing conditions and continuous production so long as there is loose coal at the face. Several loaders are usually employed at the face and the room is loaded out several times each shift. In fact, where the rooms are fairly wide, by judicious management, cutting and load-ing may go on simultaneously. Under these conditions, naturally, the face conveyor plays an important part as it is the appliance on which the coal is actually loaded. Someone has aptly stated that the loading is a question of "foot pounds," which is an appealing way to put it, for it is the number of pounds to be moved by the number of feet which measures the work to be done. It can easily be seen that the design of the face con-veyor is a matter of importance. It might be an im-perfect target for the shovel or of an awkward shape and height, and so involve extra effort on the part of the loader, tiring him when kept up continuously and at the same time slowing up his shoveling speed.

Jan 12, 1927

By R. J. Wasilewski

Electrical resistivity variation with temperature was measured on a series of alloys containting up to 33 at. pct of oxygen over the range 77° to1500°K. The resistivity behavior is highly anomalous and itzconsistent with simple metallic conduction. Both composition and temperature-depended resistivity singularities were observed. A few experiments carried out on Ti-N and Zr-O alloys indicate the presence of similar anomalies. These observations, together with the published data on effects of substi-tutional alloying on the resistiuity of titanium, suggest that the anomalies are inhevent in the electron structure of this group oj metals. The existence of two-band conduction, and a significant shift of bands relative to each other with temperature and/or the electron concentration are suggested. CONSIDERABLE advances have been made in recent years in the alloy theory of simple metals. Very little, however, is known about the bonding in transition metals and their alloys.&apos; Titanium, with its relatively few electrons, may be expected to show simpler alloying behavior than the more complex transition elements. Its alloys with the interstitial elements appear particularly attractive in an investigation of bonding characteristics because of a) the simple nature of the solute elements, b) the remarkable similarity between the equiatomic structures Tic, TiN, and TiO, and c) the extensive solid solubility ranges of oxygen and nitrogen in a titanium reported.2,3 The Ti-O system was chosen for the most extensive investigation because of the relative ease of preparation of suitable specimens. Since the main object of the work was to obtain data on the bonding and its changes on alloying, electron-sensitive properties were primarily investigated. The present work describes the investigation on the electrical resistivity-temperature-oxygen content relationships. A few experiments were also carried out at selected compositions in the Ti-N and Zr-O systems. EXPERIMENTAL Materials and Method. Polycrystalline specimens were prepared in the form of hairpin strips some 50 by 5 by 0.15 to 0.50 mm by direct metal-gas reaction. This was carried out by controlled oxidation followed by a homogenizing anneal at a higher temperature. All the test specimens were fully homogenized as judged from the uniform microstructure and microhardness. To avoid preferred orientation, each strip specimen was annealed in the ß range prior to the oxidation, this procedure assuring random orientation in the strip;4 hence any texture resulting from the oxidation reaction itself affected all the specimens to a similar extent. Titanium used was of high purity (66 DPN, 10 Kg load; major impurities 0,-43G ppm, N,-70 ppm, C-25 ppm, Fe-14G ppm). The solute content of the alloys was determined by weighing, after the reaction with a known amount of oxygen. The specimens in which the discrepancy between the volumetric and gravimetric measurements exceeded 2 pct (or 0.2 mg for the low oxygen alloys) were rejected. The mean between the two measurements was then taken as the oxygen content of the alloy. Check analyses showed no measurable nitrogen contamination. All oxygen contents are given in atomic percent. Zr-O alloys were prepared in identical manner from hafnium-free crystal bar metal, cold-rolled to strip 0.25 mm thick. Ti-N alloys required very long reaction times at the maximum temperature available (1250°C). In order, therefore, to detect possible oxygen contamination, duplicate specimens were reacted in every experimental run, and one of these was analyzed both for oxygen (vacuum fusion) and for nitrogen (Kjeldahl). Only the specimens in which the check analysis showed < 1000 ppm O were then used for resistivity investigation. Since only relatively high nitrogen alloys (7.1 at. pct; i.e., 2 wt pct N,) were investigated, this oxygen contamination was considered permissible. Dc resistance was measured by the four-probe method as previously described.= The temperature was determined with a calibrated thermocouple placed in the center of the specimen hairpin. The errors in the specimen resistance values thus obtained were estimated at 1 pct due almost exclusively to the finite thickness of the potential wires and the consequent uncertainty as regards the true resistance length of the specimen. For the calculation of the specific resistance, however, no dimensional measurements could be carried out on most of the

Jan 1, 1962