Search Documents

Jan 1, 1938

By Pétroleur Maatschappiju, N. V. de Bataafsche

Jan 1, 1939

By J. H. Henderson, T. E. Morrisson

An irvestigation has been made of the production of oil through horizontal fractures of high capacity and large radius placed at the base of producing formations. The specific aitns of the study were to (I) determine by model studies the reservoir performance when gravity drainage is the only producing mechanism, and (2) develop a method of predicting such perfortnance from commonly measured reservoir proper-ties. Although the theoretical approach tailed to develop a rigorous analytic sorution to the transient problem, it (lid lead to a practical method of predicting performance. Predictions (Ire in good agreement with rates and recoveries observed in scaled-model experinzents. Capillary effects and the influence of relative permzenbil-ity are taken into account. The experimental program was mainly concerned with the influenre of fracture radius, fracture capacily and capillary hold-up on the total recovery and the rate of recovery. Much of the experimental work was done on a triangular model which represented one-eighth of a square well pattern, so constritcted that horizontal fractures of varying radii and flow capacity could be studied. An electrolytic model was used to relate the initial production rates to fracture radius, formation thickness and the drainage radius of the well pattern. The conclusions reached as a resrtlt of the work are as follows. I. The production of oil under gravity force alone into a well-propped horizontal fracture, whose radius is of the order of hundreds of feet, is a recovery method which combines high recoveries with very acceptable production rates. 2. The mechanism is effective in "dead oil" reservoirs as well as in reservoirs which possess the energy of solution gas. 3. A method of predicting performance has been developed which gives good agreement with experimental behavior in cases of practicnl interest. Even for very thick beds and large fracture radii, where actual conditions do not conform to the assumptions made, the method gives order of magnitude predictions which would not otherwise be possible. INTRODUCTION Gravity drainage of oil from a formation which has continuous ver- tical permeability over a reasonable depth interval is a surprisingly effective method of recovery. However, for a conventional well the production rates which result from gravity drainage are so low that the economics are seldom attractive. The same formation may produce rapidly and profitably by gravity alone through a high capacity, extensive (i.e., > 100-ft radius) horizontal fracture placed near the bottom of the pay section. Fig. 1 shows a schematic diagram of the plan. Energy in the reservoir gas is not a necessary condition for this recovery process. With a sufficiently large fracture, attractive production rates will result from gravity flow alone, and the producing GOR need only be the solution GOR. It is, of course, necessary to keep the fluid level in

Discussion of the paper of Earl S. Bardwell, presented at the Butte meeting, August, 1913, and printed in Bulletin No. 79, July, 1913, pp. .1429 to 1441. H. O. HOFMAN, Boston, Mass. (communication to the Secretary*) :-It is pleasing to the originators of the planimetric determination of oxygen in refined copper to see that the method has been taken up by a large smelting plant to be used in every-day work after it has been simplified to suit the new conditions. Several years ago Huntington and Desch 1 had improved our mode of working. They projected the developed negative on to a screen, traced the outlines of the picture with a pencil, drew a border, and measured one constituent with. the planimeter. In order to give the work greater precision, they divided the area into squares of 1 cm. side, shaded the

Jan 11, 1913

AT THE beginning of December, the Lausanne Con-ference was in session. The representatives of the United States declared the American position. The representatives of Russia were received and were heard. The Turks appeared at this conference in the attitude of victors, dictating terms. The British refused to surrender Mosul, and December thus ended with this question unsettled. Early in the month the premiers of the principal powers met in London for the discussion of the German reparations question, the temporary agreement expiring on. Jan. 15, 1923. On Dec. 11 the Conference adjourned without getting anywhere, and at the end of December prospects looked more hopeless than ever. The premiers are to meet again on Jan. 2, 1923. The interruption of the London conference was followed by the intimation of early participation of the United States in European affairs in the practical way of a large loan to Germany. These intimations, ema-nating from Washington, appear to have been in the nature of trial balloons. They showed that the wind was unfavorable, the bankers not considering conditions suitable for the flotation of such a loan. British statisticians are puzzled by the fact that the trade returns of Great Britain show a greater turnover in the volume of goods during the first 11 months of 1922 than in 1920, although the rate of labor employ-ment in 1920 was nearly 100 per cent. and in 1922 only about 86 per cent., with an economic situation admit-tedly so bad as to be alarming. The British Parliament was convened under the premiership of Bonar Law. One of its first acts was confirmation of the constitution of the Irish Free State. Civil war in Ireland continued. Poland, like most of the other countries of Europe, is torn between socialism and conservatism, with the former party at present predominant. Early in December, Gabriel Narutowicz, an engineer but a radical, was elected president. On Dec: 14 he entered office and-on Dec. 16 he was assassinated.

Jan 1, 1923

By Donald B. Evans, Robert D. Pehlke

The solubility of nitrogen in liquid Fe-B alloys has been measured up to the solubility limit for the formation of boron nitride. The activity coefficient of nitrogen increases with increasing boron content in the range 0 to 7 wt pct B. From experimen -tal data, values have been calculated for the B-N interaction parameter e3 at temperatures in the range 1550" to 1750°C. A value of 0.038 has been estimated for the boron self-interaction parameter eg at 1550°C. The standard free energy of decomposition of boron nitride into the elements dissolved in liquid iron has been determined to be: ?F° = 45,900 -21.25T in the range from 1550° to 1750°C. The nitride is assumed to be of composition BN. BORON nitride has an unusual combination of properties which make it appear attractive in a wide range of engineering applications. Some of its more important and most recent applications are in the nuclear area, particularly in connection with the liquid-metal cooled reactor concept now receiving considerable emphasis. Boron nitride has a high degree of stability at elevated temperatures. It also has excellent ma-chinability and the ease with which its crystals deform suggests applications as a lubricant. These properties stem from a hexagonal layer-type structure similar to the structure of graphite. One of its primary uses to date has been for seals in liquid-metal pumping systems. It is also used in nuclear reactors as an insulating layer to separate two solid metals which are not themselves compatible under the conditions of temperature and atmosphere in which they are used. Its inertness to liquid metals has also suggested use as a mold-release agent in casting processes. In addition to its excellent machinability and reported inertness to liquid metals such as iron, silicon, aluminum, copper, and zinc, boron nitride has high thermal conductivity and excellent thermal shock resistance. This combination of properties would make it appear ideal as a refractory crucible material for refining of high-purity liquid metals, for example high-quality steels. However, since it is known that concentrations of boron as low as 50 ppm can have a marked effect on the physical properties of certain steels,' in particular on the creep and stress-rupture properties, an investigation was undertaken to define accurately the chemical equilibrium among boron, nitrogen, and liquid iron in the range of steelmaking temperatures. EXPERIMENTAL PROCEDURE Two experimental approaches to this problem were employed: a Sieverts' method and a quenching method. In the first method, the Sieverts' technique was used to measure the equilibrium nitrogen solubility in liquid Fe-B alloys of 0 to 7 pct B as a function of nitrogen gas pressure over the melt. The solubility limit of the boron nitride phase formed was determined by the point of departure of the nitrogen absorption from Sieverts' Law. This technique has been applied to liquid Fe-Ti alloys by Rao and parlee,' to liquid Fe-A1 alloys by Evans and Pehlke,3 and to solid Fe-V alloys by Fountain and Chipman.4 In the second method a melt of liquid iron was held in a crucible of boron nitride under a known partial pressure of nitrogen gas. After thermodynamic equilibrium was attained, the melt was quenched in a stream of helium and then analyzed by wet-chemical methods for boron and nitrogen. The Sieverts' apparatus used in the first method was essentially of the same design as the one described by Pehlke and Elliott.5 The charge materials were vacuum-melted high-purity iron (Ferro-vac E) supplied by the Crucible Steel Co. and -325 mesh boron powder supplied by Cooper Metallurgical Associates of Cleveland, Ohio. The boron contained less than 0.02 wt pct O, according to supplier's analysis. Recrystallized alumina crucibles were used to contain the melt. Examination of solidified melts showed these crucibles to be satisfactory with no evidence of any reaction or physical penetration of the crucible wall by the melt. The melt temperature was measured by a disappearing filament-type optical pyrometer sighted vertically downward on the melt surface through a 1/4-in.-diam sight hole in the crucible lid. The pyrometer was calibrated against the melting point of pure iron in the same apparatus, taking the emissivity of

Jan 1, 1964

By William Braden

In view of the current discussion of a proposed change in the United States mining law, abolishing the feature known as the extralateral right of a lode-location, it is an interesting circumstance that in the neighboring Province of British Columbia this feature was tried for eight years and then abandoned. The results of that abandonment have been such as to disprove the proposition, so confidently advanced by many

Jan 1, 1899

By Frank C. Roberts

Neglecting the hydrogen and hydrocarbons, 1 will assume the following analysis as a fair average composition, by weight, of the waste gases escaping from a coke-burning blast-furnace: CO2............17.25 CO,............25.25 N,.............57.50 100.00 The 25.25 CO requires for combustion 62.6 of air, or 11.398 of oxygen, necessitating the passage of 48.202 nitrogen into the products of combustion. The latter, therefore, have the following composition: CO2,,............ 56.9 N,............105.7 Tile total specific heats of these quantities of the respective gases are 12.31 and 25.79, giving for the combined product, 38.1 approximately. That is, the product of combustion will absorb 38.1

Jan 1, 1889

By E. A. Gulbransen, A. Pebler

Pressure-composition isotherms have been determinedfor the systems ZrMo2 -H2 between 0" and 900°C at hydrogen pressures between 10-4 and 760 Torr. Tkese studies plus X-ray diffraction analyses of selected compositions show that these intermetallic compounds form a complete series of hydrogen solid solutions within this temperature and pressure range. The partial molar enthalpies and entropies of solution of hydrogen in the three intermetallic compounds were calculated. The solubility of hydrogen in these Laves phases can be related to their free electron concentration. ThE reaction of hydrogen with inter metallic compounds of zirconium with Laves phase-type structure has both theoretical and practical interest. The in-termetallic compounds have structures different from any of the pure metals. In addition the electron to atom ratio of the intermetallics varies appreciably. In the nuclear materials field, these materials are of interest since intermetallic compounds may exist as precipitates in commercial zirconium alloys with transition metals. From studies on the hydrogen reaction, one can establish the stability of the intermetallic compounds relative to the hydrides of the component metals. The intermetallic compounds may also be used as getters for hydrogen and as materials for hydrogen storage. This paper will present the results of equilibrium and structural investigations of the ZrCr2-H2, the ZrV2-H2, and the ZrMo2-H2 systems for the temperature range of 0" to 900°C and the pressure range of Torr to 1 atm. A complete thermochemical analysis will be made of the measurements. Some of the results have been referred to in a survey paper' covering the types of hydrogen behavior observed in zirconium alloys. LITERATURE ZrCr2 is the only intermetallic phase in the Zr-Cr system.' It exists in two allotropic modifications. Between 900" and 1000°C the hexagonal MgZa (C14) structure transforms into the cubic MgCu2 (C15) structure. Beck4 has previously shown that the intermetallic ZrCrz takes up hydrogen into solid solution up to a composition H/ZrCr2 = 1.14 at room temperature and 1 atm hydrogen. A ZrCr2 hydride was stated to have a fcc structure. The binary Zr-V system has been investigated by williams5 although Rostoker and Yamamoto 6 had given earlier a partial phase diagram. ZrV2 was the only intermediate phase found in the system. wallbaum7 reported earlier that the compound ZrV2 hp the MgZm (CJ4) type structure with a = 5.288A and c = 8.664A. This was not comfirmed by Elliot8 nor by Matthias, Compton, and corenzwit9 who reported that ZrV2 has a cubic MgCua LC15) type structure. The latter authors gave a = 7.429A. Also, several authors do not agree on the temperature of the peri-tectic horizontal. It appears that ZrV2 may exist in several modifications. A high capacity for occluding hydrogen was reported by Beck4 who found H/ZrV2 = 1.38 at room temperature and 1 atm of hydrogen. ZrMoz is the only intermetallic phase in the Zr-Mo system.10 ZrMoa is formed by a peritectic reaction of the melt with a molybdenum-rich solid solution. ZrMo2 has the C15-type structure with a = 7.59A. MATERIALS High-purity chromium, vanadium, and molybdenum were used together with grade 1 crystal bar zirconium to prepare the alloys. Table I lists the chemical analysis and the sources for the metals. Ten-gram alloy compacts were levitated and melted in an inert argon

Jan 1, 1968

By Robert J. Linney

IN the latter part of the year 1943, it was decided to experiment with diamond-drill blast holes in the Old Bed magnetite mine at the Mineville mines of the Republic Steel Corporation, in sections of the ore body where vertical dimensions were large and where development for sublevel bench stopes had already been done. Other possibilities of application for this drilling method were in the reclamation of old floors and pillars in the pitching folds of the Lower Old Bed ore body and in the reclamation of large vertical pillars in the " 21 " Bonanza-Joker ore body. The cross sections and views of the two ore bodies will show the conditions to which the diamond-drill method has been applied. The Lower Old Bed magnetite ore body is lenticular and dips approximately 30° toward the southwest and strikes generally southeast and northwest. An intensely folded structure, which pitches generally on an axis approximately at right angles to the strike, is continuous from the uppermost old workings down to the present bottom of the mine, and probably continues with depth. On successively lower levels this folded structure becomes greater in vertical dimensions and the two folds are closer together in a horizontal dimension. As shown in Fig. 1, this folded structure gives to parts of the ore body considerable vertical dimensions, which provide areas that were developed for sublevel bench stoping above a slushing drift, as shown in Fig. 2. It was in one of these previously developed sublevel bench stopes, No. 26 on the 1185-ft. level, that the diamond-drill blast-hole method was applied for mining the upper sublevel. The lower sublevel was underhand-bench-drilled to the finger raises of the scram drift below. The roof of this stoping area began to break and spall on the lower sublevel, causing the roof to become inclined. Along the hanging wall of the stope this reached an elevation about half way between the two sublevels. A smooth schistose seam in the hanging wall causes the ore to break away freely. Therefore, if bench mining had been carried on in the upper sublevel, a dangerous condition of poorly supported benches would have resulted. When the drillers were slashing across the sublevel to footwall and hanging wall to make a bench, spalling roof of the opening below would probably have carried away part of the bench, and would have left a dangerous place in which to continue underhand benching. A 6 by 8-ft. raise had been driven between the lower stope and the upper sublevel about 200 ft. from a manway. It was decided to use this raise for a starting cut and to arrange holes as shown in Fig. 3, so that a slot would be opened across the ore body between the footwall and hanging wall. This slot would then be used for the purpose of breaking into the ore; by blasting vertical rings of holes drilled at right angles to the axis of the pitching folds as nearly as possible. Layouts of this slot drilling and the rings adjacent are

Jan 1, 1945

By Robert J. Linney

In the latter part of the year 1943, it was decided to experiment with diamond-drill blast holes in the Old Bed magnetite mine at the Mineville mines of the Republic Steel Corporation, in sections of the ore body where vertical dimensions were large and where development for sublevel bench stopes had already been done. Other possibilities of application for this drilling method were in the reclamation of old floors and pillars in the pitching folds of the Lower Old Bed ore body and in the reclamation of large vertical pillars in the "21" Bonanza-Joker ore body. The cross sections and views of the two ore bodies will show the conditions to which the diamond-drill method has been applied. The Lower Old Bed magnetite ore body is lenticular and dips approximately 30° toward the southwest and strikes generally southeast and northwest. An intensely folded structure, which pitches generally on an axis approximately at right angles to the strike, is continuous from the uppermost old workings down to the present bottom of the mine, and probably continues with depth. On successively lower levels this folded structure becomes greater in vertical dimensions and the two folds are closer together in a horizontal dimension. As shown in Fig. I, this folded structure gives to parts of the ore body considerable vertical dimensions, which provide areas that were developed for sublevel bench stoping above a slushing drift, as shown in Fig. 2. It was in one of these previously devel-oped sublevel bench stopes, No. 26 on the 1185-ft. level, that the diamond-drill blast-hole method was applied for mining the upper sublevel. The lower sublevel was underhand-bench-drilled to the finger raises of the scram drift below. The roof of this stoping area began to break and spall on the lower sublevel, causing the roof to become inclined. Along the hanging wall of the stope this reached an elevation about half way between the two sublevels. A smooth schistose seam in the hanging wall causes the ore to break away freely. Therefore, if bench mining had been carried on in the upper sublevel, a dangerous condition of poorly supported benches would have resulted. When the drillers were slashing across the sublevel te footwall and hanging wall to make a bench, spdlling roof of the opening below would probably have carried away part of the bench, and would have left a dangerous place in which to continue underhand benching. A 6 by 8-ft. raise had been driven between the lower stope and the upper sublevel about 200 ft. from a manway. It was decided to use this raise for a starting cut and to arrange holes as shown in Fig 3, so that a slot would be opened across the ore body between the footwall and hanging wall. This slot would then be used for the purpose of breaking into the ore, by blasting vertical rings of holes drilled at right angles to the axis of the pitching folds as nearly as possible. Layouts of this slot drilling and the rings adjacent are

Jan 1, 1946

By J. Moore Samuel

THE CHAIRMAN (WALTER DOUGLAS, NEW YORK, N. Y.).-Perhaps there is no problem that causes the modern metallurgist more worry than the question of unaccounted for loss. He has not the advantage of the metallurgist of the early days here, who could sleep peaceably with the settled conviction that there were certain copper mineral constituents of the ore which were volatile, and there was therefore nothing to worry about. The slag contents and volatilization accounted for the balance of the copper that went in the top of the furnace after the weighing of the bullion. There have been great strides in recent years toward reducing this loss. Perhaps the Anaconda company is the one we have to thank for the original pioneer work along the lines which we are all today following. We would be glad to hear from some gentlemen present with reference to their experience with this question of dust losses. E. P. MATHEWSON, Anaconda, Mont.-You mentioned the Anaconda company, Mr. Chairman. I would like to say something about what we have been doing there, and the troubles we have been having. We have a tremendous volume of .gas to handle. We adopted the system of large chambers, lessening the velocity of gases, and incidentally cooling the gases. Unfortunately in one sense and fortunately in another, we were compelled to increase the amount of gas handled in the flue system, and the results were then not so good. Still, we get a very good recovery. Our system of taking a sample is similar to the one described by the writer of the paper. We have tried all kinds of apparatus for getting a fair sample. We divided the area of the flue into imaginary squares, and have taken samples for a certain period of time from each square; and have used the asbestos bags. At present, there is a large unit of the Cottrell apparatus almost ready to connect up on the roaster flue to catch the dust from flotation concentrates. The worst things smelters have to handle at the present clay, they are coming in the Southwest as well as the Northwest, are of material much of which is as small as 500 mesh, and the ordinary methods of catching dust will not apply to flotation concentrates. The Cottrell process is going to be tried out at our plant for this material. We have devised special forms, with a view to preventing the formation of dust from this material, and we are pleased with the results so far obtained. There is another point in connection with this subject that I want to put before the members here, so they will be thinking about it. You know there has been a great deal of litigation between the farmers

Jan 12, 1916

By Tracy Jarrett

THE alloying of various elements with gold to produce different colors is an old art, but the effect of each element or combination of elements is not generally known. Investigations have been made in this field by F. E. Carter,1 E. M. Wise,2 and L. Sterner-Rainer.3 It is the intent of this paper to present in schematic diagrams the effects of various ele¬ments upon the color and the melting point of gold alloys. In this investigation 2-oz. melts made in a high-frequency induction furnace were used for all tests. The melting points were determined by the use of a calibrated chromel-alumel thermocouple sealed in a thin-walled alundum tube. The couple was then submerged in the molten metal and the freezing and melting points were determined by using a Leeds and Northrup potentiometer. By checking several melts using copper, zinc and gold, it was found that the accuracy of determining the melting point was within ± 5° F. To determine the differences in colors and to classify them, a wet tissue paper was placed over the polished samples and examined under a uniform white light. The 2 by ½ by 0.045-in. samples were cut from 50 per cent cold-worked strip. The original ingot was 3 by ¼ by ¾ in. This visual comparison, although not scientifically exact, served as a quite satisfactory means for determining and classifying these differences. The base alloys, or "hardeners," were first made up and analyzed, after which the gold and silver were added. This method of making up the alloys was chosen so that the same base alloy could be used for the gold alloys of different karats. The first series consisted of gold, copper, zinc and nickel, the copper comprising from 85 to 65 per cent of the content of the "hardener" and the zinc and nickel replacing copper. The second series consisted of gold, silver, copper, zinc and nickel, the copper comprising from 85 to 65 per cent of the content of the hardener with the silver, nickel and zinc replacing copper. There was no particular reason for choosing these combinations, except that they gave a color range from red-pink to white.

Jan 1, 1939

By D. B. Dowling

(San Francisco Meeting, September, 1915) THE interest which has been aroused in prospecting for oil in the foot hills of southern Alberta, and in the oil possibilities of the known gas fields situated in the less-disturbed areas, called for a much closer examination of the structure, thickness, and composition of the underlying rocks of the region than had -hitherto been made. The areal geology of the larger part of the great plains was outlined by Dawson, McConnell, and Tyrrell, between 1881 and 1885. The foothill area was not critically examined at that time, owing to the time which would have been required for its proper study and the difficulty that was found in recognizing in the foothills the divisions which had been adopted in the mapping of the formations of the plains. This was clue in great measure to the paucity of exposures in continuous sections of the lower divisions of the Upper Cretaceous. Since the pioneer work on the plains was published, the beds which form continuations south into Montana have been critically examined. The Canadian beds arch over the end of a flat anticline which rises to the south; and two sections in Montana, one on each side of the anticline, help to explain some of the difficulties previously encountered in the mapping of the measures found in the foothills. The index map, Fig. 1, shows the area studied, and its relation to southeastern Alberta, and to Montana.

Jan 6, 1915

[A AALSETH, Earl P (M 51) Consult Geol Engr 2019 Eldorado Dr, Billings, Monl ABADIE, Henry G (M 43) Asst to Supt of Oper Long Beach Oil Dev Co 925 Harbor Plaza, Long Beach 2, Calif ABBE, T Waldo (A 56) Asst Dist Oper Supt Sun Oil Co PO Box 66, Stowell, Tax ABBOTT, Fred E Jr (M 59) Abqaiq Dist Mgr Arabian American Oil Co Dhahran, Saudi, Arabia ABBOTT, Clifton T (A 60) Apartado 677, Maracaibo, Venezuela ABBOTT, J L (M 56) Partner Pritchard & Abbott 1010 Ft Worth Natl Bk Bldg, Fort Worth 2, Tex ABBOTT, Richard H (J 51) Partner Abbott & Howard 422 W Hermosa San Antonio 12, Tex .ABBOTT, William G (M 50) Div Mgr Rice Engrg & Operating Inc Box 1142, Hobbs, N. M. ABDERHALDEN, Ronald R (J 59) Prod Engr Continental Oil Co Box 100, Carmi, III ABEL, Malcolm D (J 50) Gen Partner Abel & Bancroft PO Box 865, Midland, Tex ABEL, Ramond L (M 28) Prof of Chem Eng Univ of Pittsburgh, Pittsburgh 13, Pa ABEL, Wayne K (M 57) 1513 Patton Drive, Odessa, Tex ABELL, Joseph M (J 55) Petr Engr Tennessee Gas & Oil Co Box 1772, Casper, Wyo ABELS, Thomas A (J 60) Exploit Engr Shell Oil Co Box 193, New Orleans 3, La ABENDROTH, G F (M 46) Dring Prod Supt Lyons & Logan 1500 Beck Bldg, Shreveport, La ABERCROMBIE, Bolling A (M 60) Mgr Product Planning Axelson-Garrett PO Box 2427, Longview, Tex ABERCROMBIE, C T (160) Prod Engr Cities Ser Petr Co Box 472, Brownfield, Tex ABERCROMBIE, H L Jr (J 55) Prod Engr Mobil Oil Co Room 1800 Gr PI Life Bldg, Lubbock, Tex ABERCROMBIE, Robert (J 57) Prod Engr Mobil Oil Co PO Box 1770 Shreveport, La ABERG, Richard S (M 57) Area Prod Geol Shell Oil Co of Canada, Box 100 Calgary, Alta, Canada]

Jan 1, 1961

By J. B. Umpleby

The function of gas in the development and production of oil has far-reaching consequences that should be emphasized. The technical aspects of the subject have recently had a great deal of attention but less thought has been given to fundamental concepts underlying oil and gas law and the many customs and practices that have grown up in the industry. I shall review briefly the advance in knowledge of the subject and attempt to relate these concepts to legislative, judicial and operating problems. Early writers on oil and gas in Pennsylvania noted their close association in oil pools and their contemporaneous decline in output; also, that as gas pressure decreases so does production, that new offset wells reduce the output of existing wells, and even that tubing a well lengthens its flowing life. Expanding gas was deduced as the principal expulsive force. These fundamental observations had been made at least as early as 1880.1 They were treated, however, as academic considerations and did not greatly influence law or practice for many years except to instill into all operators an urgent desire to hasten offset drilling in order to obtain as much of the flush as possible. The most noteworthy later advance in knowledge came in 1926 when Beecher and Parkhurst published their paper on Effects of Dissolved Gas upon the Viscosity and Surface Tension of OiL.² This paper added to the old idea of an expelling force the concept of a modifying agent that actually changes the physical characteristics of the oil and facilitates its movement through the pore spaces of the reservoir rock. Largely since the publication of this paper, intensive study and concerted effort have been given to means of using to a maximum, in producing oil, these combined properties of gas. This is shown clearly by the number of papers dealing with the subject, and the new and revived terms now widely used to express thought, such as the expressions gas energy, reservoir pressure, reservoir energy, gas-oil ratio, bottom-hole pressure, beaning, tapered tubing and back-pressure. These terms, some of which are

Jan 1, 1932

By Ralph D. Parker

The Frood mine (Fig. 1) is 2½ miles north of Sudbury, at a general elevation of 1000 ft. above sea level. It includes the original Frood location, which was the No. 3 mine of the Canadian Copper Co., and the adjoining Frood Extension, which until 1929 belonged to the Mond Nickel Co. Mine Openings The mine is operated from two vertical shafts and one underground incline shaft. No. 3, for men, supplies and ore, is a vertical six-compartment shaft in the footwall of the south mining area and extends froin surface to a depth of 3045 ft. No. 4 is a vertical three-compartment shaft, 2500 ft. north of No. 3 and adjacent to the north mining area. It extends from surface to a depth of 3345 ft., and is used exclusively for hoisting ore. No. 5 shaft, inclined at 65' to the horizontal and of three compartments, is near No. 4 and extends from the 2600-ft. level to 77 ft. below the 3100 level. It is used for development below the 2800 level. The ventilation shaft, No. 1, with which this paper is directly concerned, will be described fully in the following pages. Mining Methods The orcbody is laid out in 80-ft. sections at right angles to the gcneral strike and numerically indicated from the southern extremity toward the north. Each section consists of a 45-ft. stope and a 35-ft. pillar, extending the full width of the orebody. Pillars and stopes are superimposed from level to level. The present mining territory is divided into two vertical areas, a north and a south area. Both areas have the same number of stopes on each level, the two areas being separated by 10 sections to be mined later. In a few instances, at the ends of the south area, where the orebody has narrowed, longitudinal stopes are used, of more than the usual 45-ft. width. It will thus be seen that mining operations hare been concentrated in two relatively small areas, offering

Jan 1, 1934

ST. LOUIS SECTION H. A. BUEHLER, Chairman, CHARLES T. ORR, Vice-Chairman., THOMAS T. BREWSTER, Vice-Chairman, L. L. HUTCHISON, Vice-Chairman, W. E. McCOURT, Secretary-Treasurer, Washington University, St. Louis. CHARLES J. ADAMI, EUGENE MCAULIFFE, A. C. TERRILL, JAMES A. CASELTON, JAMES D. ROBERTSON. The annual meeting of the St. Louis Section was held at the St. Louis Club, Saturday evening, Mar. 10, 1917. Philip N. Moore, President, and Bradley Stoughton, Secretary of the Institute, were the guests of the Section. The meeting was preceded by a dinner, at which 70 were present, and was presided over by F. W. DeWolf. Addresses were made by Mr. Moore and Mr. Stoughton. The routine reports of the officers were- presented and the Executive Committee named above was elected for the current year. The special business of the meeting was a report of progress concerning the arrangements for the Institute meeting to be held in the St. Louis Section district, Oct. 8 to 13, 1917. The general program for the meeting met with the cordial approval and cooperation of the members of the Section. It was evident that the members are united in an endeavor to arrange a successful meeting. W. E. McCOURT, Secretary.

Jan 4, 1917

By Charles Clayton

A study of the literature shows that the greater part of research work on annealing of cold-worked iron has been for the purpose of studying the effect on grain-size and properties other than hardness. No reference has been found of experimental work of the same nature as that explained in this short paper. The material used throughout was Vismera iron, an iron containing 0.03 carbon and made several years ago by the Inland Steel Co. One-half inch stock was cut into cylinders ¾ in. long. The cylinders were then compressed for 60 sec. in a Reihle testing machine under loads as indicated below: COMPRESSION, AVERAGE LENGTH, SERIES POUNDS INCHES 1 10,000 0.693 2 15,000 .599 3 20,000 .501 4 25,000 .426 5 30,000 .378 6 35,000 .351 7 40,000 .311 Fig. 1 shows these cylinders after compression. Each series con¬sisted of 17 specimens lettered 0, B, C, D, E, E:, G, H, I, J, K, L, M, N, P, Q, and R. One specimen of each series was reserved for study of the properties in the cold-worked condition. The other specimens were annealed in a Hump furnace for ½ hr. at the following temperatures:

Jan 2, 1926

By John Griffen

This paper records over twenty years' experience with the use of the Rheolaveur system in the United States, showing its ability to meet changing conditions caused by the dirtier mine output of present-day mechanical mining methods. Data are given on size ranges handled, number and capacity of units installed, maintenance experience, and operating results on two-product and three-product separations. IT is not the purpose of this paper to discuss the principles employed in the Rheolaveur system of fine-coal cleaning as these have been fully covered in the technical literature of the Institute."2 Rather, our purpose will be to record the highlights of over 20 years' experience in the United States with Rheolaveur fine-coal launders, which will indicate their capabilities and costs of cleaning and their adaptability to meet the changing conditions caused by present-day mechanical mining methods. Rheolaveur fine-coal launders are used in the United States to treat a wide variety of size ranges of fine coal, the coarsest being 1/2 in. to 0 and the finest about 1/8 in. to 0. In Europe feeds as coarse as 5/8 in. and as small as 1/2 mm (28-mesh) to 0 are being cleaned. The size ranges usually handled in this country are 3/8 to 1/4-in. round to 0. Thirty five units with a combined hourly feed capacity of 3200 tph have been installed in the United States. Individual units are cleaning as little as 25 tph, while others are cleaning as much as 200 tph. Rheolaveur fine-coal launders offer cleaning units of high capacity and are outstanding in requiring a minimum of building space per ton of input. Experience has shown that maintenance costs are low. Several installations were made in the Pittsburgh district from 1928 to 1930, and since that time operation has been largely two shifts per day. Minor repairs to liner plates and Rheo boxes have been required during the intervening years, but no major replacement of launders was required until 1947 and 1948. At one of these plants, launders operated for 17 years before they were replaced and during that period over 26,000,000 tons of —5/16-in. coal were cleaned. The effect of the much dirtier raw coal produced by mechanical loading of the Pittsburgh seam is shown by the following tests. The data in table I summarize the performance of a Rheo fine-coal unit when cleaning hand-loaded raw coal. The —4-in. raw coal fed to the cleaning plant analyzed only 8.16 pct ash and 1.31 pct sulphur and contained 4.6 pct sink, 1.55 sp gr. Two years later, in 1945, mechanically-loaded coal from the same mine was cleaned in the same plant. The feed, —4 in., then analyzed 20.10 pct ash and 1.53 pct sulphur and contained 20.2 pct sink, 1.55 sp gr. The performance of the Rheo fine-coal unit when cleaning this coal is given in table 11. It will be noted that the +48-mesh coal is cleaned almost as thoroughly as in table I. The large amount of high-ash slimes produced from the dirtier feed are responsible for the higher ash of —--48-mesh washed coal in table 11. In this plant the Rheo fine-coal unit did not get the full load of refuse resulting from mechanical

Jan 1, 1951