Search Documents

By J. J. Pfeiffer, A. A. Oming, J. W. Myers

The method used to process washery refuse for use as a building material aggregate is described. Results of studies made in investigating this process are summarized. The Bureau of Mines, in cooperation with two commercial coal producers, studied the feasibility of using coal washery refuse in manufacturing lightweight aggregate for building materials. Lightweight aggregate is used in making masonry products of lower bulk density than can be produced from conventional aggregate such as sand, gravel, and crushed rock. Among the advantages of lightweight masonry are reduced deadweight loads which reduce materials cost, lower cost of construction labor, and improved thermal and sound insulation. A process for making lightweight concrete aggregate from coal-washery refuse appeared attractive because of the availability of raw material which contained sufficient fuel to carry out the processing. Vast quantities of such refuse have accumulated throughout the coal-producing areas of the U.S. Generally it is stored in unsightly piles, creating a problem of air pollution and using space that could be devoted to other purposes. Conversion of the refuse to lightweight aggregate could remedy these conditions and effectively utilize a material normally considered waste. The first part of the program was conducted in cooperation with the Truax-Traer Coal Co. to determine the feasibility of utilizing refuse from the company's coal preparation plant at Ceredo, W. Va., in manufacturing lightweight aggregate. The aggregate was to be used in making cement blocks comparable to those known in the building trades as cinder blocks. This project was completed in 1954. Based on the results of this work, the cooperator began commercial development and formed the Trulite Corp. for this purpose. A plant capable of handling 120 tpd of refuse was constructed for approximately $120,000. It began operating on June 1, 1955.' In 1959 a similar study was made, under a cooperative agreement with the Carbon Fuel Co. of Charleston, W. Va., to rrscertain the suitability of refuse from its plant for conversion to lightweight aggregate. Under this program various modifications of equipment were made, and the investigation of process variables begun in the previous project was extended. PROCESSING METHOD The formation of lightweight aggregate from coal-washery refuse js governed, in part, by the fusion characteristics of the mineral constituents of the refuse when heated above their softening temperatures. The heat required for this purpose is supplied by the combustihle matter in the refuse. Some of this combustible matter is coal with high ash content, but most of it is carbonaceous shale. Whereas the density of aggregate prepared from clay or shale depends largely on expansion, the density of aggregate made from refuse is reduced by burning out the combustible matter and, to a lesser extent, by expansion of the residue in the fuel bed. A chain-grate stoker with an updraft air system was chosen for the conversion process in preference to a downdraft sintering machine or a rotary kiln. In down-draft sintering, which operates on the overfeed burning principle, the volatile matter from the refuse would distill off without burning, resulting in inefficient combustion and interfering with proper operation of the equipment. The rotary kiln is designed primarily for processing material that lacks, or is low in, combustihle matter with the heat of reaction supplied from external sources. Washery refuse, which is relatively high in carbonaceous material, could burn at the wall of the kiln causing clinker formation with resultant decrease in throughput and increase in production cost. With an up-draft air stream on a chain or traveling-grate stoker, the volatile matter would be carried into the ignition and burning zones where the heat could be utilized more efficiently. The combustion procedure in this type of unit may be considered as consisting of four periods: 1) initial ignition of the top of the bed by furnace radiation, 2) ignition travel through the bed until the whole bed is ignited, 3) burnout of the combustible material with high air rates to fuse and expand the residue, 4) a cooling period. Investigation of the process required a study of the variables that affect both

Jan 1, 1962

By W. A. Anderson

Recrystallization of cold-worked metals has long been known to proceed by a process of nucleation and growth.' When a cold-worked metal is heated to a temperature at which recrystallization will ensue, nuclei of new grains, essentially strain-free, appear and grow. As the process proceeds, nuclei continue to appear and to grow, until the cold-worked matrix has been entirely consumed and recrystallization has been completed (Fig. I). Conducted isothermally, a measurement of the fraction of the matrix recrystallized plotted against time, yields an isothermal recrystallization curve, showing the time course of the recrystallization process (Fig. 2).2 Evidently, then, the rate of recrystallization is determined by the rate at which nuclei form and the rate at which they grow. The rate of nucleation N is the number of nuclei that form in unit time in unit volume of the unrecrystallized matrix, and the rate of growth G is the increase in radius of the recrystallized grain per unit time. In recent years attempts have been made to determine N and G as these vary with the well-recognized variables affecting recrystallization: time, temperature, degree of deformation, etc.1 Such studies yield information that is more fundamental than that conveyed by the conventional recrystallization diagram,' since the rate of recrvstallization is thus analyzed into its two component rates3 Methods are now available by which N and G can be measured, and analytical expressions have been developed for the interrelationships among N, G, the isothermal recrystallization curve, and the final grain size, which greatly facilitate analysis.2-4 The application of these methods has been demonstrated recently for the recrystallization of silicon ferrite.2 Data on N and G in dependence upon the recognized recrystallization variables are, however, very fragmentary;" values of N and G have been determined for some metals, but the effect of temperature, which would yield the fundamentally important activation energies, has been too little studied. Thus far there has been no detailed study of the recrystallization of any one metal in terms of X and G ovcr appreciable ranges of the variables time, temperature, degree of deformation, and original grain size. It is the purpose of the present paper to provide such a study, employing aluminum.

Jan 1, 1945

By Carl H. Samans

THE INFORMATION AVAILABLE on the rolling characteristics of the precious metals-gold, silver, the platinum metals and their alloys-is incomplete and mostly from scattered sources. In the present paper an effort has been made to assemble and correlate it and to fill in some of the gaps that exist. GENERAL ROLLING CHARACTERISTICS SOME EFFECTS OF IMPURITIES Gold and its alloys are generally considered to be hot short and hence are usually rolled cold. Cold rolling of the yellow, green, and pink gold alloys. Which customarily contain gold, silver, copper and zinc and frequently some nickel as well, introduces no new problems since reasonable reductions are quite feasible and the alloys show little tendency to fire crack in subsequent annealing. The white gold alloys. which usually contain little or no silver and 10 pct or more nickel, are very susceptible to fire cracking1 and hence wrist he given relatively heavy reductions, i. e., 8-10 pct or more per pass with a total reduction of about 50 pct between anneals, to minimize this tendency. In addition, it is preferable to keep the bar as flat as possible during rolling. Although no comprehensive study appears to have been made of the effects of impurities on the cold rolling characteristics of gold alloys, the observations of Nowack2 on the effects of small

Jan 1, 1948

Accurate modeling of the semivariogram is an extremely important step in the geostatistical analysis of mineral deposits. Automatic fitting of a mathematical model is often possible but not necessarily desirable. Significant geologic and statistical information must be taken into account in the fitting process, which is not always available to the computer. Manual model fitting is, on the other hand, extremely time consuming. Interactive graphics are best suited to optimize the process. Many interactive methods are described, which are adapted to modeling semivariogram in one-, two-, or three- dimensional environments.

Jan 1, 1985

By E. T. Turkdogan, J. H. Swisher

bi the fivst part of the paper results ave given on the rate of decarburization of Fe-C melts ln CO2-CO atmospheres at 1580°C. The rate -controlling step is believed to he that irvlloluing dissociation of curbotz dioxide on the suvfuce of the melt. 4 genevral reaction mechanistm is poslnlated jor gels-t11eta1 veactions oc-curit~g on the surface of iron coutcotamncited with chemi-sovbed osygesL. Oxygen the present work on decavbuvization of liquid iron and previous studies on the kinetics of nitrogen absorption and desorplion are discussed in terms of the postulated mechanism, ManY of the early studies of rate of decarburization of liquid steel were of an exploratory nature and laboratory exppriments carried out pertained to open-hearth or oxygen steelmaking processes. References to previous work on this subject may be found in a literature survey made by Ward. Using more sophisticated experimental techniques, several investigators have recently studied the kinetics of decarburization of molten Fe-C alloys in oxygen-bearing gases. For example, Baker et al2.' reported their findings on the rate of decarburization of liquid iron, levitated by an electromagnetic field, in carbon dioxide-carbon monoxide-helium atmospheres. In these levitation experiments the samples used were small in size, e.g., -0.6-cm-diam spheres weighing -0.7 g, and the rates were measured for decarburization from about 5 to 1 pct C at 1660°C. The rates obtained under their experimental conditions were considered to be controlled primarily by gaseous diffusion through the boundary layer at the surface of the levitated melt. Parlee and coworkers3 measured the rate of absorption of carbon monoxide in liquid iron. The rates were found to follow first-order reaction kinetics, yielding a reaction velocity or a mass transfer coefficient in the range 0.2 to 0.4 cm per min. The coefficient was found to decrease with increasing carbon content of the melt. These investigators attributed the observed rates to the transfer of carbon or oxygen through the diffusion boundary layer adjacent to the surface of the melt. In the work to be reported in this paper, an attempt has been made to study the kinetics of gas-metal surface reactions involved in the decarburization of liquid iron. EXPERIMENTAL The experiments consisted of melting 80-g samples from an Fe-1 pct C master alloy in an induction furnace and decarburizing in controlled CO2-CO mixtures at 1 atm pressure and 1580°C. The master alloy was prepared by adding graphite to electrolytic "Plastiron" melted in racuo. None of the impurities in the master alloy exceeded 0.005 pct. The reacting gases were dried by passage through columns of anhydrone; in addition, CO2 impurity in carbon monoxide was removed by passage through a column of ascarite. A schematic diagram of the apparatus is shown in Fig. 1. A 1.25-in.-diam recrys-tallized alumina crucible containing the sample was placed inside a 3-in.-diam quartz reaction tube, all of which was surrounded by an induction coil. A 450-kcps induction generator was used as the power source. Water-cooled brass flanges, which contained the gas inlet, gas exit, and sight port, were sealed to the top of the reaction tube with epoxy resin. The reacting gases were metered with capillary flowmeters and passed through a platinum wire-wound alumina preheating tube, 0.25 in. ID and 11 in. long. The gases were preheated to about 1300°C. A disappearing-filament optical pyrometer was used to measure the melt temperature. The pyrometer was initially calibrated against a Pt-6 pct Rh/Pt-30 pct Rh thermocouple. The temperature was controlled to within +10°C by manually adjusting the power input to the induction coil. In a typical experiment, an 80-g sample of the master alloy was melted in a CO2-CO atmosphere having pcO2/pco = 0.02 and flowing at 1 liter per min. A negligible amount of carbon was lost and no significant reduction of alumina from the crucible occurred during melting, e.g., 0.005 pct Al in the metal. After reaching the experimental temperature of 1580°C, the gas composition was changed to that desired for a particular series of decarburization experiments. The duration of the transient period for obtaining the desired gas composition at the surface of the melt was about 20 sec . The flow rate of the reacting gas was maintained at 1 liter per min. After a predetermined reaction time, the power to the furnace was turned off. During freezing, which took about 10 sec, the amount of gas evolution was not sufficient to result in a significant loss of carbon. The samples were analyzed for carbon by combustion and in a few cases they were analyzed for oxygen by the vacuum-fusion method. RESULTS A marked increase in the rate of decarburization of iron with increasing pcO2/pco ratio in the gas stream is demonstrated by the experimental results given in Figs. 2 and 3 for pco2/pco ratios from 0.033 to 4.0. In one series of experiments, denoted by filled triangles in Fig. 2, the reacting gas was diluted with argon (48 vol pct) resulting in a slower rate of decarburization. Samples from two series of experiments with pco2/pco = 0.033 and pco2/pco = 0.10 (with argon dilufion) were analyzed for oxygen. In these Samples the oxygen content increased with reaction time

Jan 1, 1968

By Roland J. Lapee

A history of the progress made in copper refining in Montana is presented. The casting furnaces and the newly rebuilt electrolytic refinery are descmbed and operating details are given. Experiences with various addition agents, effects of rernoval of chlorine from the electrolyte, and effects of separan on electrolyte and on copper deposit are discussed. Observatzons are made on the effect of various impurities in anode copper and behavior of thezr salts in electrolyte and in slime, on treatment of slime for removal of copper, and on electrolyte puriification problems. The improved method for production of starting sheets is described. Attention is given to new materials for construction and to improvement in matrials handling ad quality control. COPPER refining at Great Falls, Montana, dates back to 1892. The original plant produced 65,000 lb. of cathodes per day at a current density of 16 amp per sq ft. In this plant anodes and cathodes were handled to and from the cells by means of hand-operated chain blocks and were moved about the plant by hand trucks. Cathodes were melted in coal-fired, reverbera-tory furnaces, were charged by hand, and refined copper was dipped by hand and cast in iron molds. In 1916, a new, modern plant with capacity to refine 18 million Ib. copper per month was built. Two refining furnaces were built, and each was provided with a twenty-mold Clark casting wheel. In 1922, the furnaces were converted to the use of pulverized coal: in 1923, to the use of oil; and in 1928, to the use of natural gas. In 1926, the plant was enlarged 50 pct. The use of pulverized coal for refining copper at Great Falls was discussed1 in a paper presented at the Salt Lake City meeting of the Institute in September 1925. Also, a comparison of the use of various fuels in copper refining furnaces was discussed 2 in a paper presented at the New York meeting of the Institute in February 1932. Prior to 1943 the cellroom was operated with twenty-five 720-lb. anodes and 26 cathodes per cell. Four cathodes, each weighing about 165 lb., were produced from an anode. In 1943 the weight of the anode was reduced to 460 lb., and two cathodes, each weighing about 190 lb., were produced from an anode. In 1949, a Billet Casting Wheel for the production of 3 in. diam phosphor deoxidized billets was built. A paper, presented at the New York Meeting of the Institute in February 1956, describes3 this plant and operation. In the electrolytic refinery, production is controlled by variation of the current density. In 1956, germanium rectifiers on a separate electrical circuit were provided for the starting sheet section so that current density could be maintained at any desired figure. Also in 1956, a program of modernization and enlargement of the Electrolytic Copper Refinery was started. This program, when completed, will raise the capacity of the Great Falls Electrolytic Copper Refinery approximately 33 pct, to 33 million lb. of cathodes per month. Furnace capacity for melting cathodes and anode scrap is ample to take care of the increased production from the electrolytic refinery. This fortunate condition came about primarily as the result of the three following changes: 1) The furnaces were lengthened 10 ft in 1922 when the fireboxes were found unnecessary for burning powdered coal. 2) Furnace life, and hence furnace capacity, was increased by the successful efforts of the Copper Refinery staff to develop a method for sanding furnace side walls and roof. 3) The natural gas being used has a very low sulfur content. As a result, it is possible to reduce time spent rabbling and poling and thus greatly increase tons per furnace charge. TANKHOUSE AND TANKS The Great Falls Electrolytic Refinery is 535 ft long by 252 ft wide. The cells are arranged in four crane bays in which are operated seven 10 ton Whiting Cranes. The old cells are in groups of ten, with circulation of electrolyte through five cells in cascade and with aisles between the groups of ten cells. The new cells are nested in groups of sixteen with no aisles, are all on one level, and have individual circulation to each cell. Present plans call for 1792 commercial cells and 128 stripper cells. To reduce confusion during the construction period, and to use the cranes, cars, and other equipment already on hand, the cells in the rebuilt section were designed to have approximately the same inside dimensions as the cells in the old part of the

Jan 1, 1962

By V. N. Mackiw, D. E. Weir, D. J. I. Evans

The world's largest reserves of nickel are found in lateritic ores. Commercial exploitation has been carried out for almost one hundred years; however, none of the plants currently in operation produce pure nickel but rather ferronickel, matte, impure nickel oxide or mixed sulphide precipitate. Over the past decade Sherritt has studied various processes, including the modified reduction roast-ammonia-ammonium carbonate leach process, for the production of pure nickel powder and briquettes from laterites. Nickel can be reduced to the pure elemental form at elevated temperatures and pressures from impure basic nickel carbonate slurries. Several methods were studied in the development of the process for working up the pregnant leach liquor and basic nickel carbonate to produce feed for the aqueous hydrogen reduction step in which pure nickel powder is produced. This paper is concerned only with the laboratory studies using the basic nickel carbonate slurry reduction procedures.

Jan 1, 1973

By W. T. Bishop

For many years pine oil has been used extensively as a frother for the flotation of minerals, particularly sulphides, yet the published information available to the average user on its composition, chemical and physical properties, has been rather meager. It is the purpose of this paper to discuss these points and their relationship to the frothing properties of pine oil used in flotation processes. Pine oil, as the name implies, is a liquid obtained from the processing of wood of the longleaf and other southern pines. It is a complex mixture of naturally occurring terpene derivatives, primarily alcohols, and a smaller amount of terpenes, which has found many uses in various industries. Its use as a frother in flotation processes was the first large-scale application in industry and today the mining industry still consumes large quantities of pine oil but the textile and disinfectant industries consume comparable volumes. Much is used in soap manufacture and laundry operations. The surface-active properties of pine oil are in a large degree responsible for this versatility. History The name "Naval Stores" goes back to the days when pine tar and pitch were used to caulk leaky ships and 'Oat their ropes and rigging. Today this term is still used to include not only the oleoresinous products of the pine tree—rosin and turpentine— but other products such as pine oil, pine tar, and the many terpene and resinous compounds obtained by extracting the pine wood or tapping the tree. That part of the industry known as "wood naval stores" dates from about the beginning of this century and today produces a large part of the country's rosin and turpentine by processing pine wood. In addition, all of our natural pine oil is supplied by the wood naval stores industry, as tapping of the live tree gives only rosin and turpentine. This latter phase is known as the "gum naval stores " industry. The first successful commercial operation of the steam and solvent process of the wood naval stores in industry was carried out by Yaryan at Cadillac, Mich., in 1909.1 This operation did not prove profitable, so Yaryan went south to utilize the longleaf pine, and built a plant at Gulfport, Miss.2 Soon after, another plant was built at Brunswick, Ga., which is still in operation, and in 1914 was reported to have processed about 500 tons of wood per day.' In 1921 Hercules Powder Co. acquired the Yaryan interests, at which time the production of pine oil was only 3 to 5 million pounds per year and flotation was the largest customer. As time went on, technological advances were made, other companies entered the field, and the production of pine oil increased many fold. The growth of the industry was especially marked during the past 10 years, and in

Jan 1, 1947

By W. T. Bishop

For many years pine oil has been used extensively as a frother for the flotation of minerals, particularly sulphides, yet the published information available to the average user on its composition, chemical and physical properties, has been rather meager. It is the purpose of this paper to discuss these points and their relationship to the frothing properties of pine oil used in flotation processes. Pine oil, as the name implies, is a liquid obtained from the processing of wood of the longleaf and other southern pines. It is a complex mixture of naturally occurring terpene derivatives, primarily alcohols, and a smaller amount of terpenes, which has found many uses in various industries. Its use as a frother in flotation processes was the first large-scale application in industry and today the mining industry still consumes large quantities of pine oil but the textile and disinfectant industries consume comparable volumes. Much is used in soap manufacture and laundry operations. The surface-active properties of pine oil are in a large degree responsible for this versatility. History The name "Naval Stores" goes back to the days when pine tar and pitch were used to caulk leaky ships and 'Oat their ropes and rigging. Today this term is still used to include not only the oleoresinous products of the pine tree—rosin and turpentine— but other products such as pine oil, pine tar, and the many terpene and resinous compounds obtained by extracting the pine wood or tapping the tree. That part of the industry known as "wood naval stores" dates from about the beginning of this century and today produces a large part of the country's rosin and turpentine by processing pine wood. In addition, all of our natural pine oil is supplied by the wood naval stores industry, as tapping of the live tree gives only rosin and turpentine. This latter phase is known as the "gum naval stores " industry. The first successful commercial operation of the steam and solvent process of the wood naval stores in industry was carried out by Yaryan at Cadillac, Mich., in 1909.1 This operation did not prove profitable, so Yaryan went south to utilize the longleaf pine, and built a plant at Gulfport, Miss.2 Soon after, another plant was built at Brunswick, Ga., which is still in operation, and in 1914 was reported to have processed about 500 tons of wood per day.' In 1921 Hercules Powder Co. acquired the Yaryan interests, at which time the production of pine oil was only 3 to 5 million pounds per year and flotation was the largest customer. As time went on, technological advances were made, other companies entered the field, and the production of pine oil increased many fold. The growth of the industry was especially marked during the past 10 years, and in

Jan 1, 1947

By H. C. Casey, M. B. Panish

The roles of the phase diagram and the diffusion and solubility analyses in the selection of sources for the diffusion of zinc into GaAs are discussed. Isothermal sections of- the phase diagram are described at 1000°, 775°, 744°, and 700°. Below 744° the three solid phases, Zn3As2, GaAs, and ZnAsz, may be in equilibrium. In the composition regions where the three solid phases are in equilibrium, the partial pressures of the components do not vary with composition and there is no liquid phase. A diffusion source composition within that region containing 5, 50, and 45 at. pct Ga, As, and Zn was selected to yield reproducible diffusion profiles without surface damage. The 5/50/45 ternary source Provides a significant improvement in the reproducibility and planarity of- the zinc diffusion as compared with other zinc diffusion sources that result from starting with elemental zinc, dilute solutions of zinc in gallium, or various combinations of zinc and arsenic. Several experimental diffision profiles for the 5/50/45 diffusion source have been determined. The profiles are very steep in the region of the junction and produce devices that exhibit step junction behavior. The junction depth varies as the square root of time. Diffusion at 700°C for 4 hr gives a 5-µ junction depth and a surface concentration of 2.4 x1020 cm-3. The surface concentration is enhanced by a factor of three and the junction depth decreased by a factor of ten as compared with diffusion with a starting source 01- elemental zinc. The differences in dijyusion behavior with these two sources are due primarily to the approximately 10' greater equilibrium As4 partial pressure for the 5/50/45 source. ThE most common technique for the preparation of GaAs p-n junctions for diverse applications ranging from switching diodes to injection lasers has been to diffuse zinc into the solid from the vapor phase. The zinc impurity has generally been provided by introducing into a diffusion ampoule elemental zinc, dilute solutions of zinc in gallium, or various combinations of zinc and arsenic. For the purpose of eliminating surface deterioration, zinc has been diffused into GaAs through SiO2 films1 and from zinc-doped SiO2 films.2 During a study of the injection and recombination mechanisms in GaAs junctions, we found that these diffusion techniques either resulted in nonreproducible diffusion profiles and nonplanar junction interfaces or were extremely inconvenient to use. An unpublished report by Allen and pearson3 emphasized that an understanding of diffusion requires relating the diffusion conditions and system compositions to the ternary phase diagram. Recent studies have made it possible to relate the effect of starting source composition on the GaAs sample surface and diffusion profile reproducibility and, in addition, to estimate the expected surface concentration and zinc diffusivity. These studies include the Ga-As-Zn phase diagram,415 the determination of the incorporation reaction for zinc as a substitutional impurity,6 and the analysis of the concentration dependence of the diffusion coefficient.' In this paper the role of the phase diagram in the selection of the starting diffusion source composition is illustrated, and an application of the diffusion and solubility analyses is used to demonstrate their utility in the estimation of surface concentration and diffusivity for various starting source compositions. Consideration of the isothermal sections of the ternary phase diagram shows that below about 744° C a composition region exists where the three solid phases Zn3As2, GaAs, and ZnAs2 are in equilibrium without a liquid phase. In this region the partial pressures of the components do not vary with composition, and thus the surface concentration and diffusivity depend only on temperature. A diffusion source composition within that region containing 5, 50, and 45 at. pct Ga, As, and Zn was selected. As will be described in detail, this diffusion source yields reproducible diffusion profiles without surface damage, planar junction interfaces, and steep profiles that result in devices with step junction behavior. Only closed diffusion systems are considered. Open or flowing vapor systems require the maintaining of constant vapor pressures in the flowing gas and represent control problems outside the scope of this discussion.

Jan 1, 1969

By William C. Cooley

INTRODUCTION Considerable research has been conducted on the use of steady and pulsed jets of water at high pressures to produce slots or holes in rock, and to fracture rock. The primary objectives of prior research have generally been to determine the feasibility of excavating or drilling rock or minerals and to determine the optimum jet parameters for this purpose. The present study was undertaken in order to identify the pertinent dimensionless parameters involving jet and rock properties which characterize the liquid jet penetration process and to develop empirical correlations of the existing test data which would permit engineering prediction by means of scaling relationships. The present paper is in the nature of a progress report, because not all the existing test data have been processed. Also effort has been concentrated on correlation of data on the specific energy (jet kinetic energy per unit volume of rock removed or broken), rather than correlation of jet penetration depth, hole diameter, kerf depth or kerf width. However, it is clear that this method of correlating data on specific energy in terms of dimensionless parameters shows great promise and provides insight into the nature of the physical processes of jet erosion and fracture. It therefore can help to avoid drawing incorrect conclusions from limited experimental data. DIMENSIONAL ANALYSIS The method of dimensional analysis is particularly valuable where the mathematical relationships controlling a physical process are unknown or complex. The grouping

Jan 1, 1971

By Whitman E. Brown, Louis J. Erck

L. A. ROE*—This paper is one of great value to the iron ore industry. The Humphreys spiral is a relatively new tool and gives promise of being quite useful in solving certain problems of iron ore beneficiation. Spirals have been tested on a martite ore at the Benson mine of Jones and Laughlin Steel Corp. in northern New York State. Our New York ore is considerably different, physically and mineralogically, than the one mentioned in this paper, and contains only 25 pct iron. This ore can be processed on spirals to give a concentrate containing 62 pct iron with an 85 pct recovery. On our particular ore we found operating difficulties when the spiral feed was coarser than 14 mesh. These were chiefly due to excessive "build-up" of locked middlings in the spiral circuit. In extreme cases these middling particles would accumulate to such an extent that the plant had to be shut down and the spiral surge tanks cleaned out. It is interesting to note that there exists a close relationship between the results of tabling a given iron ore and concentration of this same ore on Humphreys spirals. The size range of the ore must, of course, be within those limits acceptable to spiral concentration. Comparative tests on several of our mar-tite ores showed tabling results to be the same as spiral results. The authors make no mention of the use of a tailing stream splitter (now available from the spiral manufacturer) which is a useful tool in studying iron losses in the tailings stream. 011 our particular martite ore we found a considerable accumulation of fine-sized iron ore particles in the outside portion of the tailings stream. This fraction may be amenable to further treatment. E. H. ROSE*—The authors have concluded an interesting piece of work and this paper is an excellent factual account of a rapid and somewhat unusual transi-;ion in practice in the plant described. Perhaps it was modesty on their part which caused them so casually to limit to one sentence the fact that "several other methods of concentration on the fine ores representative of the Hill Trumbull group . . . failed to produce consistently an acceptable grade and recovery of finished product." The fact is that they were confronted by a difficult mineral-dressing problem and they are to be congratulated on their courage and persistence in staying with it until a satisfactory solution was evolved. A visitor to the plant might have been mildly astonished, as I was, to see one type of concentrator handling that part of the load early in the 1947 season, its experimental replacement by another a little later, and then in 1948 to see that both types had simply disappeared and their place taken by the spirals which were operating as placidly as though they had been there all the time. In working out economic methods of beneficiating Alabama red ore, most of which development is still ahead of us, it is likely that we also will pass through a period of successive disappointments, for we too have a problem where it is next to impossible either to "guess 'end right in the first place," or, because full-scale operating cost is such an important factor, to lay the ultimate answer on the line in advance by means of laboratory experimentation. Iron ore being what it is instead of what it used to be, it is encouraging to have the example the authors have given us today that a tough nut that will not crack on the first blow or the second is apt to do so on the third or fourth.

Jan 1, 1950

By H. S. Price, D. A. T. Donohue

The system of equations describing displacement of a hydrocarbon liquid by a hydrocarbon vapor in a porous medium where mass transfer takes place between the phases is solved numerically for a variety of gas injection processes. Even though the method of solution is quite general, only systems with three hydrocarbon components are considered. Computer simulations of displacement processes wherein mass transfer between phases is both considered and neglected are compared, and it is shown that neglecting mass transfer can give pessimistic displacement efficiencies. INTRODUCTION The role of the gas displacement process in the recovery of petroleum has been subjected to a series of detailed analyses; as a result, a number of predictive models have been published in the literature. However, because of major simplifying assumptions, most of these models do not completely represent the physical system. As a result, the effect of making the simplifying assumptions is unknown. Therefore, a complete representation of this process — one without major simplifying assumptions —should lead to a fuller understanding of the process, and perhaps to methods of improving it. The general method of developing a model for two-phase fluid flow in a porous medium is to solve simultaneously the continuity equation, the energy equations and the equation-of-state for each phase under the prescribed initial and boundary conditions. For an isothermal system, the energy equations reduce to the momentum equation. Darcy's law. However, since natural gas is the vapor state of the reservoir liquid, interphase mass transfer may take place with concomitant changes in both the intensive and extensive thermodynamic properties of each phase. It is this phenomenon that has often been omitted in previous mathematical models. An additional relation, then, which accounts for mass transfer between the phases, must be included with the other equations to specify a complete model. Completely formulating the equations to be solved is not a difficult task1 but obtaining their solution has been intractable up to now. Availability of large-memory, high-speed digital computers now makes an attack on this formidable problem possible. This paper presents a preliminary study of the problem. Since this investigation is intended to be exploratory, it is restricted to the linear, horizontal, isothermal, two-phase viscous flow of oil and gas in an oil reservoir. In the early development of predictive models of this process, the reservoir system was considered as a unit and various forms of the material balance equation were proposed.2-4 Pressure and saturation gradients were then added in the Buckley-Leverett model.5 The Buckley-Leverett formulation considered the fluids to be incompressible; thus, the mathematical model reduces to a steady-state system. In the 1950's, studies incorporating numerical techniques were being published.6-9 These mathematical models differed in the efficiency of finite difference techniques, the inclusion or exclusion of capillarity or the number of space dimensions considered. To solve these nonlinear, partial differential equations, each phase was considered to be homogeneous with time; therefore, mass transfer between phases was neglected. The effect of mass transfer on the gas displacement process was first reported by Attra. 10 He simulated the one-dimension flow system by a series of cells in each of which the fluids were equilibrated during a time step. In addition, the pressure throughout the system during each time step was predetermined and constant-phase velocities were calculated according to the Buckley-Leverett incompressible fluid flow model. Welge et al.11 developed a model for the displacement of oil by an enriched gas where composition is considered to be a dependent variable. Fluid

By A. D. Hoagland

The Flat Gap mine is located on Copper Ridge in the Appalachian Valley of East Tennessee. Large zinc orebodies occupy zones of solution and collapse breccias in Lower Ordovician Kingsport limestone and dolomite. The principal ore mineral is sphalerite and the principal gangue is dolomite. The ore-bearing horizons are considerably more than 95% covered by thick residual clay. Geochemical prospecting under these conditions is an effective exploration technique which played an important role in the discovery and exploration of the Flat Gap mine. The Flat Gap mine, an important zinc deposit of the Appalachian type, is located in the Copper Ridge Belt in the Valley of Tennessee approximately 30 miles northeast of the Mascot-Jefferson City zinc district (Fig. 1). The ore is found in large stratigraphically linked deposits in solution and collapse breccias of the Kingsport, Longview and, to a minor extent, Mascot formations of Lower Ordovician age. The principal ore mineral is sphalerite and the principal gangue minerals are dolcrmite and accessory pyrite. There is local minor galena and very rare barite and fluorite. The ore-bearing horizons are covered by about 20 to 100 ft or more of residual clay except where active streams have exposed bedrock. Considerably less than 5% of the favorable host rocks are exposed in outcrop, and this nearly complete soil cover creates a serious obstacle to exploration. Comprehensive surveys of the base metal content of soils furnish a useful substitute for outcrop geology, and under favorable conditions, this technique is a very valuable prospecting tool. The analysis is carried out by a titrametric dithizone method modified after the procedure described by E. B. Sandell.' This method detects

Jan 1, 1962

By Eben E. Olcott

The Mine.—For some years attention has been drawn to the copper deposits of the Appalachian range of mountains, and especially to those in that portion crossing the corners of Virginia, North Carolina, and Tennessee. Certain it is that in many places in this locality available deposits of copper await the miner, and one after another are being opened and worked. The parts of these three States alluded to are but sparsely settled, and communications are insufficient to meet the demand for transportation. Railroads are wanted, as the existing wagon roads are unfitted for heavy hauling; these circumstances increase very much the difficulties in the way of mining enterprises. Notwithstanding this, the success of some of the mines of this section is an established fact, and Ducktown has for some years held a high rank among the copper-producing localities of the United States. of all these deposits, however, none is more interesting or more deserving of attention than the one now under consideration. The works of the Ore Knob Copper Company have been energetically pushed forward, since the reopening of the mine, in the spring of 1873, by Mr. J. E. Clayt,on, the superintendent and one of the chief owners of the property, and if one thing more than another can insure success it is the combination in this gentleman of rare business capabilities with the deepest personal interest in the prosperity of the undertaking. The copper vein at Ore Knob* is a clearly defined fissure traversing the gneissic rocks of Pre-silurian age in a direction 61' east of north.

ON p. 499 of the December issue Of MINING AND METAL-LURGY plans were announced for a memorial to en-gineers who died in overseas service during the World War and a gift to the University of Louvain on behalf of the engineers of America. In this connection it is proposed to erect a memorial tablet giving the names. of engineers who died in the foreign service. Members of the A. I. M. E. who gave their lives, so far as they are known, are listed below. It will be much appreciated if notice be given of any omissions and also if the name of some surviving relative be supplied in each case. Louis Baird, Lieut., Royal Field Artillery, British Army, killed on the battlefield, 1915. John H. Bellamy, Capt., Regimental Staff, 103rd Engi-neers, killed near Fismes, Aug. 9, 1918. Martin F. Bowles, Lieut., 1st Battalion, 355th Infantry, 89th Division, killed on the battlefield, Sept. 3, 1918. Andrew Burt, died in .active service, 1916. Stanley B. Carlisle, Machine Gun Battalion 346, 91st Divi- sion, died in France, Oct. 24, 1918.

Jan 1, 1928

THOSE MARKED THUS * ARE MEMBERS, MARKED THUS t ARE ASSOCIATES THESE SIGNS DOUBLED INDICATE LIFE MEMBERS AND ASSOCIATES RESPECTIVELY THE FIGURES AT THE END OF THE ADDRESS INDICATE THE YEAR OF ELECTION HEAVY FACED TYPE SIGNIFIES HONORARY MEMBERSHIP ` *AARONS, JULIAN B , Mine Supt, The Boulder Deep Levels, Ltd , Boulder, Western Australia, '05 *ABADIE, EMILE R, Cons and Min Engr, 1004 James Flood Bldg, San Francisco, Cal '76 *ABBE, CLEVELAND, JR, GeOl Aid, U S Geological Survey, Washington, D C '00 *ABBOTT, AI ARTHUR, Cerro de Pasco Mining CO , Cerro de Pasco, Peru, So America '95 *ABBOTT, ARTHUR V , Electrical Engr , Westinghouse, Church, Kerr & CO , 8 Bridge St, New York, N Y '82 *ABBOTT, CLARENCE E, Chief Min Engr, Care Fayal Mine, Eveleth, Minn '04

Jan 1, 1910

By A. Kaufman

More than 3 trillion gal of water are used annually by the mineral industry. Of this, approximately 21/2 trillion gal are recirculated, the rest constituting intake water. The major users are natural gas processing plants and phosphate rock, sand and gravel, and iron ore producers. Water was used by the mineral industry for mining (6%), processing (64%), cooling and condensing (27%), and miscellaneous uses such as boiler feed and sanitary purposes (3%). Whereas total water use is dependent on the quantity of material processed and on the particular process requirements of an industry, recirculation is dependent on processing, as well as cooling and condensing requirements, quality of new water intake, and the necessity for treating new and discharged water. Consumed water, on the other hand, is dependent on the quantity of water recirculated, and temperature and humidity in the area. Based on this analysis, an increase in water use by the mineral industry of 21/2 times by 1985 is forecast. Wster intake, however, will only rise 62%, because of a substantial increase in recirculation. In one report of a special series concerning the water resources of the United States, the Senate Select Committee on National Water Resources, 87th Congress, estimated that water demand would double by 1980 and triple by 2000.' In view of the possible water deficiencies that might result from such expanded usage and the need for research guidance, the Bureau of Mines organized and carried out a statistical canvass of water use in the mineral industry for calendar year 1962. The data used in this paper, unless otherwise noted, are derived from that canvass.' The efforts in this paper are devoted toward summarization of the canvass and analysis of the data. SOME DEFINITIONS Intake: Water introduced from an external source for the first time into a given mine or plant regardless of quality. Intake water is also called new water, water withdrawn, or makeup water. Fresh Water: Water suitable for cooking and drinking. Saline Water: Water containing more than 1000 parts per million of dissolved solids. Contaminated Water: Water not suitable for domestic use, but excluding saline water. Recirculated Water: Water reused to conserve intake water. Solutions that are recycled primarily because of fixed metallurgical practices, such as copper leaching solutions containing sulfuric acid, are excluded. Gross Water Used: Recirculated water plus intake water. Also called total water used. Consumed Water: Water that is lost by evaporation, as well as water lost in product. Seepage and transferred water are not considered consumed. The use of either intake or recirculated water may result in consumption. However, because of difficulties in measuring consulmption, consumed water is defined as the residual between intake and water discharged from the mine or plant. Mineral Industry: For the purposes of this paper, mineral industry includes all metal and nonmetal surface and underground mines and their associated processing plants, as well as custom mills, coal washing plants and associated mines, petroleum and natural gas well drillers, natural gas processing plants, and secondary recovery operations. WATER USE IN THE MINERAL INDUSTRY Water used by the mineral industry constitutes a relatively minor fraction of the water withdrawn by all users. Data compiled by the U.S. Geological Survey in 1960 indicate that water withdrawals, exclusive of that used to generate hydropower, approximate 99 trillion gal annually.3 Our data indicate that water withdrawals by the mineral industry comprise only 1% of this total, or 2% of the water withdrawn by industrial users. Use by Industry: Water used by various mineral industries is shown in Table I. The table indicates that close to one-half of the gross water used by the mineral industry in 1962 was used by natural gas processing plants, followed by sand and gravel, phosphate rock, and iron ore producers. The largest aggregate users of water are also the largest users per dollar of product. For example, Fig. 1 shows that the natural gas processing and phosphate rock industries are very large users of water per dollar of product. Their recirculation per

Jan 1, 1968

[ASSETS Equity in Engineering Societies Building $491,642.36 Books in Library 40,000.00 Investments: Life Membership Fund $ 16,381.18 James Douglas Library Fund 99,999.36 Robert W. Hunt Fund 7,497.33 J. E. Johnson, Jr. Fund 3,000.00 James Douglas Medal Fund 3,250.00 General Reserve Fund 13,896.75 144,024.62 Cash 47,467.02 Paper on hand 5,253.83 Accounts Receivable 1,124.49 Supplies on hand 163.84 $729,676.16] [ ]

Jan 1, 1925

By G. M. Willis, F. L. Hennessy

The oxygen pressure in equilibrium with silver and Ag2O-B2O3 melts has been measured between 800' and 900°C, to obtain the thermodynamic properties of the liquid. The compound Ag20. 4B20:1 appears to exist in the liquid, which shows marked heat content and entropy effects. A KNOWLEDGE of the thermodynamic properties of binary liquid silicates, borates, and phosphates would be of considerable assistance in the interpretation of the behavior of multi-component metallurgical slags. However, the literature contains comparatively few studies of the thermodynamics of binary slags. The system Ag20-B,O, attracted our attention as it was known to give a single liquid phase,',' in which high contents of silver could be obtained (up to 61 pct Ag according to Foex2). Further, it would be expected that the partial pressure of oxygen over melts in equilibrium with metallic silver could be used to determine the activity of Ag2O in the Ag,O-B,O, system. In many respects, it may be expected that the reaction of a basic oxide with boric oxide would be analogous to its reaction with silica. Liquid immiscibility frequently occurs in both borate and silicate systems. With B2O3 and SiO reaction with a basic oxide presumably involves a breakdown of the three-dimensional network of the acid oxide by reaction with oxygen atoms common to more than one silicon or boron atom. Ag2O-B2O3 was therefore investigated as a model of a slag system in the hope that its thermodynamic properties would assist in understanding those of other systems. Several methods for determining the activity of a component in a slag have been described in the literature. Chang and Derge" used high temperature electromotive force measurements to obtain the activity of SiO2 in CaO-SiO2 and Ca0-Al203-Si02 slags, but the cell reaction in their work is not clear. low has used rate of volatilization and vapor pressure measurements combined with phase diagrams to obtain activities in the systems KO-SiO,, Na,O-SiO, and Li,O-SiO," and PbO-SiO26 Taylor and Chipman7 extrapolated their results for the distribution of FeO between liquid iron and CaO (+Mg0)-FeO-SiOl slags to obtain the activity of FeO in the binary FeO-SiO2 system. In principle, one of the most direct methods for obtaining the activity of a metallic oxide in a phase is by comparison of the equilibrium oxygen pressure for the system metal-pure oxide with that of metal oxide-containing phase. Schenck and othersa have studied the stabilization of Ag2O on combination with other oxides (MO,) in the solid state by measurements of the oxygen pressure in systems of the type Ag-Ag,O-xM0,-MOy-0, (gas). Schuhmann and Ensio" have determined the activity of FeO in iron silicate slags in equilibrium with solid iron, using CO/CO2 mixtures to establish known partial pressure of oxygen. Although the method gives the activity of FeO without ambiguity, the slag is not a binary system, and interpretation of the results in terms of the hypothetical binary system FeO-SiO, is not possible. If a metal is solid at temperatures at which the properties of the slag containing its oxide are to be studied, this method has the considerable experimental advantage that the metal can be used as the container for the slag, and contamination by contact with refractories is avoided. In this work, crucibles for Ag2-B,O, melts were made from silver, and the liquid brought to equilibrium with definite pressures of oxygen gas. The oxygen pressure PO, thus fixes the activity of Ag20 in the liquid silver borate. For the reaction at a given temperature. is substantially constant, is directly proportional to the square root of the equilibrium oxygen pressure. Varying the oxygen pressure changed the silver oxide content of the liquid and it was possible to obtain the activity of Ag2O over a range of composition. Experimental Procedure In principle, the method consisted of bringing melts in silver crucibles or boats to equilibrium at a fixed temperature under a definite pressure of oxygen and analyzing the glass after solidification. Materials: B2O3 glass was prepared from A.R. quality boric acid by fusion in platinum. The silver

Jan 1, 1954