Search Documents

By Wilhelm Rohn

IN discussing the influence of a content of gases on metals and alloys we should probably first consider the physical and chemical conditions under which these gases may be present. By a chemical analysis, such as the total extraction of gases from the liquid metal by melting in a graphite crucible in vacuo, we find only the sum of gaseous chemical elements contained in the metal in any form and no reference is made to the special form under which they have been present previously. CONDITION OF GASES IN METALS In considering gases . in metals we may first turn our attention to gases simply dissolved. Because the solubility of almost any gas decreases suddenly at the freezing point, most of them are released during solidification, developing rise of ingots and blowholes. If only a little gas is dissolved in the molten metal the size of such blowholes may be miscroscopical, or even submicroscopical, resulting in a certain reduction of the notched-bar impact test values. Hydrogen is believed to become less soluble as the temperature is lowered and therefore increasing quantities of this gas may be evolved during cooling between the freezing point and room temperature, leading to unsoundness of the ingot at weak spots; i.e., at the grain boundaries. This gas at the grain boundaries probably is present at high pressure and therefore impairs the mechanical properties to a degree similar to that found in the hydrogen embrittlement of copper. Usually we may trace such gases by observing rising ingots, or at least by the formation of a characteristic pattern of small grooves upon etching.

Jan 1, 1932

By Albert Phillips

As EARLY As 1824, Haidinger1 described crystals of native copper that were, according to Dana,2 "probably twinned parallel to the octahedral plane and normal to this axis." In 1837, Rose3 very clearly demonstrated that native copper crystals were commonly twinned on the octahedral plane. Lasaulx,4 in 1882, described polysynthetic octahedral twins and stated that enclosed twinning lamellae were observed. Even on crystals formed artificially by. electrolysis, twinning was observed as early as 1886, by Brown.5 Many other descriptions of twinning in native copper and in gold and silver are to be found in the literature, and in every case with which we are acquainted the twinning is conformable to the spinel law; i. e., the octahedral plane is both twinning and composition plane. Metallurgists have long been familiar with the straight-sided bars or bands that commonly occur within the irregularly outlined grains of metallic crystalline aggregates. They are certainly found in nearly all metals of the face-centered cubic type after cold working and annealing. If a specimen showing these bands is rotated, keeping the angle of incidence of the illuminating beam constant, they usually exchange color contrast periodically with their respective matrix crystals. Also slip lines, when produced in these specimens, nearly always show a change in direction upon passing through the bands, giving rise to the "stairway" effect often illustrated in metallurgical textbooks. Apparently the only quantitative observations on bands of this sort were made by Osmond and Cartaud6 on austenitic steel. They selected,

Jan 1, 1928

By Nathaniel Herz

IN the operation of any ore processing plant, no matter what beneficiation process or combination of processes may be used, certain fundamental figures are regularly needed for essential records and accounting. These include amounts of ore treated and products made, with their assays, as well as quantities of labor and supplies used, with their cost. Usually labor and supplies are broken down and allocated to certain operations by the accounting department, and resulting tabulations are available for study by the milling plant management. However, to avoid too many minor details that would make these reports cumbersome and involved, much information that could be useful to the plant operator is often consolidated in such a manner as to have lost a considerable part of its value. To clarify this point, it may be stated that top management is most concerned with production figures and cost of production, while the plant operator is also interested in quantities of labor in man- hours and amounts of supplies used. Due to varying unit prices of labor and supplies, comparisons on a dollar basis alone are often misleading. With rising unit costs of the past few years now about twice as high as they were a few years ago, constant study of quantities involved is required to improve efficiency and productivity.

Jan 6, 1957

ROBERT E. TALLY,* Jerome, Ariz. (written discussion ?).-Mr. Sherman's paper, entitled "Measures for Controlling Fires at the Copper Queen Mine," embodies two new and very important features: First, automatic closing of doors communicating with the dangerous area; second, the use of a portable storage-battery fan. His other procedures, such as giving a general fire alarm, getting workmen to the surface, etc., are equally important, but have long been in use in other places. Fire and ventilating doors in connections leading to shafts, air raises, and other large timbered areas, have been in use at other mines; but the method described by Mr. Sherman for operating these doors by compressed air, through a valve on the surface, is, so far as I know, original, and should be installed in every mine where there is danger of fire. Nearly all large mines are now using artificial ventilation, with the result that there are strong air currents in the shafts and other important workings. The most important feature in mine fires is a quick and positive control of the ventilation, for it takes but a few moments for smoke to travel over a large area, with the usual results of suffocation, and destruction of property. A strong air current in an upcast shaft acts as a draft in case of fire, and unless quickly cut off the fire would soon get beyond control. An upcast shaft usually changes to a downcast when large amounts of water are used. Human lives are in more danger from downcast currents, as the smoke travels into the workings.

Jan 4, 1918

By E. R. Parker, D. L. Martin

In a previous paper one of the authors observed that the rate of cooling from the anneal prior to testing greatly influenced the life of copper under sustained load at 200°C. Furnace-cooled bars of oxygen-free copper (with and without silver) had a life four to twenty-five times that of the water-quenched specimens. The addition of 0.054 per cent silver to the oxygen-free copper increased the life at a stress of 20,000 lb. per sq. in. from about 2 hr. to 50 hr. Fractures in these bars were intercrystalline. An explanation was advanced to account for the profound influence of cooling rate on the rupture properties at 200°C. The suggestion offered was that at the high annealing temperature the minor constituents are distributed at random. By water quenching, this condition is maintained at room temperature, whereas furnace cooling permits some segregation at the grain boundaries. The higher concentration of the minor constituents in the grain boundaries results in a. strengthening, so that a longer life at a given stress and .temperature results. Small amounts of cadmium or manganese have also been found to increase the life of copper at 200°C., and to a much greater extent than silver.2 The increase in the long-time strength of copper resulting from small additions of cadmium or silver appears to be related, indirectly at least, to the higher softening temperatures of such alloys. The elements, such as silver or cadmium, which greatly increase the rupture life of copper also cause large increases in the softening temperature. As little as 0.05 per cent of cadmium or silver is sufficient to raise the softening temperature more than 100°.3,4 The effects of cooling rate and of minor constituents on the rupture properties are of considerable fundamental as well as practical interest; therefore a more detailed study of their nature was conducted and is reported in this paper. Experimental Procedure Materials The materials studied in this investigation may conveniently be classified in two groups: one consisting of a wide variety of commercial coppers, and the other composed of special high-purity, laboratory-prepared coppers. The commercial materials were tested to determine whether or not the effect of cooling rate occurred with all coppers, whereas the high-purity coppers were investigated in order to establish a basis for evaluating the effect of minor constituents on the rupture properties. In Table I are given the analyses of the coppers tested. The samples I to 6 are commercial materials and were obtained for the most part from stock supplies.*

Jan 1, 1944

By D. L. Martin, E. R. Parker

In a previous paper one of the authors observed that the rate of cooling from the anneal prior to testing greatly influenced the life of copper under sustained load at 200°C. Furnace-cooled bars of oxygen-free copper (with and without silver) had a life four to twenty-five times that of the water-quenched specimens. The addition of 0.054 per cent silver to the oxygen-free copper increased the life at a stress of 20,000 lb. per sq. in. from about 2 hr. to 50 hr. Fractures in these bars were intercrystalline. An explanation was advanced to account for the profound influence of cooling rate on the rupture properties at 200°C. The suggestion offered was that at the high annealing temperature the minor constituents are distributed at random. By water quenching, this condition is maintained at room temperature, whereas furnace cooling permits some segregation at the grain boundaries. The higher concentration of the minor constituents in the grain boundaries results in a. strengthening, so that a longer life at a given stress and .temperature results. Small amounts of cadmium or manganese have also been found to increase the life of copper at 200°C., and to a much greater extent than silver.2 The increase in the long-time strength of copper resulting from small additions of cadmium or silver appears to be related, indirectly at least, to the higher softening temperatures of such alloys. The elements, such as silver or cadmium, which greatly increase the rupture life of copper also cause large increases in the softening temperature. As little as 0.05 per cent of cadmium or silver is sufficient to raise the softening temperature more than 100°.3,4 The effects of cooling rate and of minor constituents on the rupture properties are of considerable fundamental as well as practical interest; therefore a more detailed study of their nature was conducted and is reported in this paper. Experimental Procedure Materials The materials studied in this investigation may conveniently be classified in two groups: one consisting of a wide variety of commercial coppers, and the other composed of special high-purity, laboratory-prepared coppers. The commercial materials were tested to determine whether or not the effect of cooling rate occurred with all coppers, whereas the high-purity coppers were investigated in order to establish a basis for evaluating the effect of minor constituents on the rupture properties. In Table I are given the analyses of the coppers tested. The samples I to 6 are commercial materials and were obtained for the most part from stock supplies.*

Jan 1, 1944

By Mourad Aissa

From our previous work (Gardner, Aissa, and Verghese, 1982) on determining the residence time distribution of ball mi 11s from radiotracer data taken in closed-circuit operation without interruption of the process, it occurred to us that the data taken for this purpose also contained information on the breakage rates of all the sizes present. It is the purpose of the present work to evaluate methods to obtain breakage rates from this data. A numerical solution for the impulse injection and subsequent detection of radiotracer in a closed-circuit linear comminution process is developed and used with typical breakage parameters, residence time distribution, and classifier functions to study and evaluate these methods.

Jan 1, 1984

By Chas. F. Jackson

IN these days the headlines and spotlight have been focused largely upon the new processes developed and new plants erected to meet the multiplied demands for mineral products required for prosecution of the war. By comparison, the less spectacular achievements of the miner, who is meeting the demand for raw material without which these processes and plants would be useless, have received little attention. Attendance at the mining meetings here reported was small, averaging about 35 to 40, but interest was as keen as ever, and evidenced to your reporter that the miner is no less on the job than is the metallurgist. It is evident that the mine operators are not neglecting any improved methods and practices in their struggle to produce more in the face of diminishing labor supply.

Jan 1, 1943

By E. S. Machlin, W. R. Yankee

IN a previous study1 of the effect of heating com-mercial titanium in air on its subsequent friction coefficient against other metals, as well as itself, it was found that the friction coefficient markedly decreased from a value of about 0.7 to about 0.3. A tentative explanation was given that surfaces normally produced at room temperature are not contaminated sufficiently to prevent seizing or welding of the titanium to the softer mating metals. The latter tend to cleanse themselves during rubbing over the harder titanium. It was thought that the lack of a contaminant protective film on the titanium was due to the high solubility of titanium for oxygen and nitrogen and hence an inability to form a contaminant oxide or nitride. This explanation requires the ratio of the surface absorption rate to the diffusion rate to become much lower at room temperature than it is at high temperatures. In order to check the phenomenon further, commercial titanium specimens were nitrided or oxidized at 800°C for 20 hr in flows of prepurified N2 and 01, respectively, at about 1/2 in. H2O above atmospheric pressure. Friction runs were made in argon using a freshly cut copper hemisphere (cut in argon) on surfaces cut successively into the diffusion layers in the titanium (cut in argon) using the techniques described in a previous publication.' DPH values (100 gram load) were made as a function of depth into the diffusion layer using a Tukon tester. Also, micrographs were taken at separate cross sections to indicate the diffusion layers. The results obtained are presented in Figs. 1 and 2, which show the "static" friction coefficient vs hardness for the nitrided and oxidized specimens, respectively. A separate measurement of the friction coefficient of clean copper vs iodide titanium also was made. From results reported in the literature' giving the oxygen and nitrogen contents as functions of the hardness, cross plots were made showing the friction coefficients as functions of the amount of interstitial solute. These plots are given in Figs. 3 and 4. From micrographs of the diffusion layers and the phase diagrams, it was deduced that the data in Figs. l through 4 correspond to the single phase a region. The points observed on the compound regions have been excluded from the figures. It is apparent that nitrogen or oxygen in solution in the a titanium markedly affects the friction coefficient against a softer mating metal. Discussion of Results These results are extremely interesting from both a practical and theoretical viewpoint. The theoretical implications will be discussed first. According to Bowden, the friction coefficient should be given to a good approximation by the relation where a is the fraction of contact area that has welded, a is the shear strength of weaker component, and H is the hardness of softer component. Using this relation alone, it is difficult to understand the results because none of the terms should be affected by a variation in the oxygen or nitrogen content of the harder and stronger metal, titanium. Even if the ratio of S/H for titanium is used in Eq. 1, the ratio has been shown to be independent of oxy-gen or nitrogen content.' If a more rigorous equa-tion is used combining Eq. 1 and a result given pre-viously" for the case where welding is absent, then the relation obtained is µ = a S/H + (1-a) a W aß/H where a is constant and Waß is the work of adhesion between the two metals comprising the friction couple. This relation states that if a is less than 1/2 or so, variation in the work of adhesion Waß between copper and the titanium should affect the friction coefficient markedly. It is reasonable to expect that the work of adhesion will depend on the oxygen or nitrogen content of the titanium. Available data4 show that clean metals and oxides have much lower works of adhesion than the same metals against the

Jan 1, 1955

By R. A. Graham, R. W. Rohde

The effect of hydrostatic pressure upon the austenite start temperature of a commercial Fe-28.4 at. pct Ni-0.5 at. pct C alloy has been determined. For pressures to 20 kbar, the austenite start temperature decreased from its atmospheric pressure value of 380°C at the rate of about 4°C per kbar. These data are analyzed by two different thermodynamic approaches; first, considering the transformation as an isothermal process, and second, considering the transformation as an isentropic process. It was found that both these approaches fit the experimental data equally well. The effect of hydrostatic pressure upon the austenite start temperature is best described by considering the mechanical work done during the transformation as that work obtained by multiplying the applied pressure with the gross volume change of the transformation. It is widely recognized1 that strain has an important effect on the initiation of martensitic transformations.* For example, the martensite start tempera- *In this paper, use of the term martensitic transformation implies the reversal of martensite to austenite as wen as the formation of martensite from austenite. ture, M,, may be increased by plastic deformation. Similarly, plastic deformation is observed to lower the austenite start temperature, A,. The effect of uniaxial stress on the M, of iron-nickel alloys has been studied by Kulin, Cohen, and Averbach.2 They found that the martensite start temperature was significantly changed by stresses well within the elastic region. Moreover, the effect of tensile and compres-sive stresses differed. These effects were explained in terms of the interaction of the applied stress with both the dilational and shear components of the transformation strain. The magnitudes of the influence of uniaxial tension, compression and hydrostatic pressure on Ms were measured in 30 pct Ni 70 pct Fe by Pate1 and Cohen.3 Their thermodynamic calculations and similar calculations by Fisher and Turnbull4 predicted the experimental results when the transformation was assumed to occur isothermally at some fixed driving force. This driving force was assumed to be supplied by a combination of the chemical free energy difference between the austenitic and martensitic phases and the work performed during transformation by the applied stress. More recently, Russell and winchel15 reported the effect of rapidly applied shear stress on the reversal of martensite to austenite in iron-nickel-carbon alloys. They performed a thermodynamic analysis of this transformation based upon the assumption that the re- versal occurred adiabatically. They concluded that the applied shear stress did not significantly interact with the transformation strain and thus did not assist in inducing the reversal. Rather they concluded that the reversal was effected by localized strain heating which resulted from the gross local shear deformation of the experiment. In either the adiabatic or isothermal analysis it is necessary to compute the work performed by the interaction of the applied stress and the transformation strains. In the case of hydrostatic pressure this interaction has been treated by two different methods. In either case the applied pressure is assumed to remain constant during the transformation. In one treatment the applied pressure is assumed to interact directly with the dilatational strain associated with the formation of an individual martensite plate.3'4 This local strain has been measured at atmospheric pressure in iron-nickel alloys by Machlin and Cohen.6 In the above treatment this local strain is assumed invariant with temperature and pressure changes. In the other treatment the applied pressure is assumed to interact with the gross volume change of the transformation.7,8 The usefulness of this latter treatment has been demonstrated by Kaufman, Leyenaar, and Harvey7 who calculated the effects of pressure upon the martensite and austenite start temperatures of Fe-10 at. pct Ni and Fe-25 at. pct Ni alloys. Excellent agreement was obtained between their calculations and their experimental data on an Fe-9.5 at. pct Ni alloy. However, this treatment suffers from the fact that the data required to calculate the volume change of the transformation (i.e., the initial specific volumes, the thermal expansion and compressibility data for both the austenitic and martensitic phases) is, in general, not available for any material except pure iron. Thus the calculations of Kaufman et al.7 were necessarily performed by assuming that the volume change of the martensitic transformation in the iron-nickel alloys was that same volume change occurring during the a-? transformation in pure iron. While this approximation may suffice for very dilute alloys it is likely to be inaccurate in high nickel alloys. We have performed measurements of the effect of hydrostatic pressure to 20 kbar on the A, temperature of an Fe-28.4 at. pct Ni-0.5 at. pct C alloy. The composition is similar to the alloy used by Pate1 and Cohen3 to determine the effect of pressure upon the M, temperature. The present measurements permit calculation of the interaction between the applied pressure and the transformation strain. Additionally, measurements have been made which allow precise determination of the gross volume change of the transformation. The data allow direct comparison between the alternate hypotheses of the interaction between the applied pressure and a dilatational transformation strain characterized by either the formation

Jan 1, 1970

By Francis O. Blackwell

There are few industries in which power is more important to successful operation than mining, and none in which it is so difficult to ohtain power cheaply. Fuel is usually expeusive in mining districts, ana the ma chinery may be widely scattered and located in places difficult of access. The work is often so intermittent and variable as to prevent the economical use of steam. Mining operations are likely to exhibit accumulations of comparatively small and inefficient engines, numerous boilers and long lines of wasteful steam-pipes. Conlpressed air, as a means of transmitting power, is so handicapped by losses in the compressors and piping that it is limited to short distances and to the operation of apparatus requiring power, without regard to cost. To-day, electricity is rapidly replacing other methods of power-distribution, primarily because it is practically independent of distance. By selecting a potential proportional to the length of transmission, the cost of electric conductors and the e5ciency are the same for all distances within reasonable limits. For instance, a given amount of power can be delivered either 528 ft. away at 100 volts, or 50 miles at 50,000 volts, with the same total of copper per H.P. and with exactly the same loss of power in the transmissioo-circuk. This independence of distance permits the selection of the place most advantageous for power-development as a site for an electric power-plant, and the co~~centration there of the generation of all the power required within a radius of many miles. The powel.-site may be at a fall of water, if one is available, or a steam-plant can be built where fuel and supplies are cheapest, or where suflicient water is available for boiler-feed and condensing purposes.

Jan 1, 1904

By W. J. Taylor

FURNACE-MEN who have not taken advantage of the use of dynamite in certain blast-furnace troubles, as explained by Mr. Witherbee in his valuable papers read before the Institute some years since, cannot appreciate the quick relief and great advantage that may be derived at times from its judicious employment. Before giving my experience in the use of high explosives in blastfurnace troubles of certain kinds, I will record a method I have used with marked success in " blowing down." Had I not understood, however, the use of powder, I would have " salamandered " effectually the first time I tried it. Early in my straight-furnace experiments, last summer, at the Chester, N. J., Furnace, I wanted to blow down to within 3 or 4 feet of the tuyeres. To do this with a down-comer not lined, and without putting in any limestone to keep the gases cool enough to do no harm, was not an easy task. We could keep the bell and hopper cool by filling them with water, say 12 inches deep; but before we got the stock down 15 or 20 feet the pyrometer in the gas-flue on top mas up to 1300°, and the clowncomer was red-hot, with the heat still rising. In this emergency my assistant, Mr. N. M. Langdon, urged the trial of a plan lie had often advocated, viz., the introduction of water in some way under the bell in the proper quantity, in order that its evaporation might absorb and reduce the heat of the escaping gases to a point where it would not do any harm. He thought the bell

Jan 1, 1885

C. E. Dewey, Georgetown, Colo. (communication to the Secretary) : In his remarks on crushing-machinery, Mr. Douglas says (Twins., xxii., p. 322): "To insure a smaller and more uniform size of particles in the crushed material, the Dodge crusher still communicates motion to the upper extremity of tile movable jaw, which oscillates on fixed pivots projecting from its lower extremity!' The notion that, in order to obtain a fine and uniform product from a rock-breaker, the movable jaw must be pivoted at its lower extremity, seems to obtain generally among mill-men, as well as among manufacturers of machinery. My experience with machines of both types does not confirm this belief. It is true that, to obtain a uniformly fine product from a jaw-crusher, the stroke at the lower extremity of the crushing-surface must be short; but that the movement at that end must be less than at the other or receiving-end is, I think, an erroneous assumption. Figs. 1 and 2 are intended to illustrate the two types of machine. It is found in practice that the capacity and the nature of the product of either machine, as usually constructed, are governed by the opening, C D, and the length of stroke of the movable jaw at D. This being the case, machines of either type, of the same width of crushing-surface, running at the same speed, and having the same adjustment as to opening and stroke at D, should give, when fed

Jan 1, 1895

By H. W. Mead, C. E. Birchenall

The rates of growth of graphite nodules in cast irons are calculated for a model of a growing graphite sphere surrounded by a shell of austenite through which carbon and iron are diffusing. The carbon is supplied by a cementite-austenite mixture at the outer edge of the shell. The calculated rates from carbon diffusion agree fairly well with the measured values, but the rates based on iron self-diffusion are much too low. Because the iron must be removed for the process to continue, o plastic deformation mechanism is suggested. THERE has been an unfortunate tendency in the literature of growth and dissolution reactions to identify the slope of a plot of the logarithm of the growth or dissolution rate vs reciprocal of temperature with the activation energies determined by diffusion measurements in chemically similar systems. If the solubility limits at the growing or dissolving phase interfaces change appreciably with temperature, such procedures may lead to serious errors in specifying the mechanisms controlling the rates of these processes. A reaction involving the simultaneous growth of graphite from and dissolution of cementite in austenite will be discussed here to show that substantial oversimplifications have been made in earlier studies of this process. From a dilatometric study of the overall y-range graphitization process, Bunin and Danil'chenko' found an apparent activation energy of 90 kcal per g-atom. They concluded that, since this value was much nearer the approximately 68 kcal per g-atom observed for self-diffusion in pure iron than it was to 32 kcal per g-atom for diffusion of carbon in iron, the rate-controlling process must be the diffusion of iron away from the growth interface to provide space for graphite to grow. Bunin and Salli' bolstered this agreement with the observation that graphite forms preferentially at surfaces, cracks, and pores where free volume is present initially. Ziegler, Meinhart, and DeaconQ ad found an apparent activation energy for graphitization of 98 kcal per g-atom. This value, like that of Bunin and Danil'chenko, applies to nucleation and growth occurring simultaneously. It is not generally assumed that nucleation is entirely diffusion-controlled. Treatments such as prior cold-working and prequenching, which strongly affect the rate of graphitization, would be expected to have little effect on diffusion processes occurring at the graphitization temperature. In any case 90 kcal per g-atom is not particularly close to the 54 kcal or lower to be expected for diffusion of iron which is carbon-saturated.' The presence of silicon in iron is said to reduce the activation energy for diffusion,' so its presence in cast irons would be expected to have a similar effect. The growth rates of nearly spherical graphite nodules have been studied by Brown and Hawkes." The initial rate of growth before impingement of adjacent carbon-depleted areas was found to be parabolic, and rate constants were measured at several temperatures. Their apparent activation energy for the growth process only was roughly 45 kcal per mol. Burke and Owen' made growth-rate measurements on several alloys, recording appreciable induction periods, initial nucleation rates, and average radial growth rates based on an assumed linear rate of radial growth. They found that increased silicon content increases the ovel-all reaction rate and the initial rate of nucleation, and decreases the induction period. Assuming 1) spherical nodules. 2) constant volume rate of nucleation, 3) austenite in equilibrium with cementite at positions where the cementite is not depleted, and 4) a constant diffusion distance during the growth of a nodule, they calculated an apparent overall activation energy of 68 kcal per mol, which was related to an activation energy for nucleation of 79 kcal per mol and activation energy

Jan 1, 1957

By Oliver C. Ralston

This paper reports the results of the use of salt in some research work carried on during the past 3 years at the Salt Lake City Station of the Bureau of Mines, which is quartered in the University of Utah, whose Metallurgical Research Department cooperates with the Bureau. Only the work involving the use of salt is described. The authors wish equal credit given to J. F. Cullen, C. L. Larson, C. Y. Pfoutz, C. E. Sims, H. C. Neeld, R. W. Johnson, F. G. Moses, N. C. Christensen, and G. H. Wigton, who have all in some way contributed toward the success of this work, while connected with the station in one way or another. Lead Metallurgy Popularly Supposed to be Without Problems In lead metallurgy it is difficult at first to find metallurgical problems, as the prevailing conception has been that lead is so easily concentrated in its various ores and so easily reduced to its metallic form that the only progress possible is that involved in cheapening methods of mining and of reduction. Most of the problems usually considered are of minor nature and do not involve radical metallurgical changes. During the three years of work of the Salt Lake Station, the following classification of problems in the metallurgy of lead has been made: Oxidized Ores. 1. Ores containing only lead. 2. Ores containing lead and silver or gold. 3. Ores containing lead and zinc, with or without silver. Sulphide Ores. 1. Ores of pyrite carrying some lead. 2. Ores of complex zinc-lead-iron sulphides. 3. Complex sulphides containing precious metals.

Jan 1, 1918

By K. R. Weller

The Ardlethan Tin Ltd. concentrator typically recovers 55% of the tin in a gravity concentrate at 51% grade from fresh ore assaying 0.5% Sn. Coarse gravity concentration is performed in a complex circuit involving Reichert cones, spirals, shaking tables and two regrind mills. The paper describes how flow and size-by-size sample data from a steady-state survey were used to construct a computer model of the plant involving 46 process streams. The data reduction involved a computer- aided mass balancing technique, recovery-size modelling of gravity concentrators and the use of a mineral dressing flowsheet simulator. The model was used to simulate possible rearrangements of the available equipment. Early simulations indicated that improved performance could be obtained by using spirals to-treat cone middlings or tailings rather than cone concentrates. A test spiral rig was used at Ardlethan to determine typical performances for all cone product streams and the results were incorporated in new simulations. A revised circuit was recommended and implemented by Ardlethan Tin as far as physical restraints within the plant would allow. Production figures show that a substantial increase in tin recovery and 10-15% increase in milling rate were achieved following the circuit changes, and these improvements were sustained over a six month period.

Jan 1, 1984

By P. Duwez, C. B. Jordan

A. J. SHALER*—I should like to congratulate the authors for having carried out such a precise set of experiments. It has been found useful, in sintering experimental compacts in vacuo, to make certain that the residual gas is not one which reacts with the metal. Since traces of oxygen can be kept away only with great difficulty, the technique is often adopted of using a "getter " of powder in the vicinity of the compacts, and, in addition, of permitting a small hydrogen leak to flow into the vacuum chamber. Did the authors use similar devices? This paper brings up a question concerning the definition of the word ' sintering.' The authors restrict its use to the adhesion between particles. Kuczynski, in a paper presented at this meeting, applies the word to the growth of areas of contact between particles. I have used it to mean both these phenomena and also the dimensional changes which continue to take place after the first two have run their course. May I suggest that we should come to an agreement on the use of these words ? Fig 1 and 2 show an interesting feature: extrapolation of the curves to zero time does not give a densification parameter of zero. The higher the temperature, the higher is the intercept on that axis. These observations agree with the concept of a practically instantaneous densification taking place while the compact is being brought to heat. Such a change may be brought about by plastic deformation and primary creep. The stress pattern causing this first rapid flow is, to my mind, due to the force of attraction between the surfaces of opposite particles in the regions immediately flanking their common areas of contact. The stress is not temperature-sensitive, but at room temperature plastic deformation only proceeds until the metal in the area of contact can support it elastically. As the metal is heated, the elastic limit falls, and further plastic flow occurs. At the higher temperatures, this is followed by primary creep, and finally by the steady-state rate-reaction which the authors are seeking. If they were to recalculate their densification-parameter values, using, not the initial density of the cold compact, but the density after the compacts have been brought to temperature, the systematic deviations from linearity in Fig 3 and 4 might be eliminated. Such initial densities might be obtained by extrapolating the curves of Fig 1 and 2 to zero time. I am naturally pleased to see that such a very well done series of experiments leads to a heat of activation (for the densification process in hydrogen) that is much higher than that for self-diffusion, in confirmation of the less elaborate results reported by Wulff and myself (Ind. and Eng. Chem., (1948) 40, 838). J. T. KEMP*—I would like to comment on Dr. Shaler's remarks. There are apparently different interpretations of the word "sintering." It seems to me that an accurate definition of our word is essential in all metallurgy. May I point out, in this connection, that in practical metallurgy the word "sintering" has been applied to a bonding process in the preparation of ores and flue dust for fur-nacing. It would be unfortunate if in the area of powdered metallurgy we should establish a definition that is essentially different in meaning. F. N. RHINES*—I think that I can answer the question by saying that I see no essential difference between the use of the term "sintering" in extractive metallurgy and in powder metallurgy; physically the same things are going on. I admit sintering is used for different end purposes in the two cases. When we resort to the sintering of lead ore mixture we are doing so to obtain a chemically reactive, loose texture of some rigidity. This is only a difference in use. After all, in powder metallurgy we sometimes deliberately produce a very porous material which has just a little strength, just as in the case of sinter cake. P. DUWEZ (authors' reply)—We agree that it would be helpful to have well-established definitions of such terms as "sintering." Since the question has now been raised, the time might be appropriate for its consideration by some suitable committee of one or more of the metallurgical societies. In answer to Dr. Shaler's first question, no getter nor hydrogen leak was used in our vacuum experiments, except insofar as the guard disks (used to reduce friction between specimens and trays) may have acted as getters. Dr. Shaler's statement that extrapolation of the curves of Fig 1 and 2 does not lead to zero densification at zero time apparently overlooks the logarithmic

Jan 1, 1950

By William Metcalf

One of the first questions that naturally occurs to one who handles steel is, " Why does steel harden?" To answer this question the chemist and physicist have devoted much thought and experiment, and while they have enriched our store of knowledge of the nature and composition of steel, it cannot be said that they have yet solved the problem involved in its hardening. In this communication I desire to direct attention to a line of investigation yet new, in the hope that it may receive the attention. of those who have the time and ability to pursue it. I refer to magnetism. There are so many parallels between the action of magnetism on iron and steel and their behavior under different processes of manipulation that it would seem. as if there must be some connection between tile forces at work in the different cases, if, indeed, there be not an identify of force in all of these cases. Magnetism, as me know it, may be merely the visible manifestation of forces, which may serve as a guide to lead us to an exact knowledge of the structure, tile strains, and the resistances with which me have to deal in iron and steel. If a magnet be brought close to a pile of iron filings, the little pieces of iron will fly to the maguet and attach themselves to it, with their longer axes lying in the direction of the force. If molten cast iron be poured into an iron mould,—a chill,—the iron upon crystallizing will form needlelike crystals, with their long axes normal to the surfaces of the mould. • If the iron is at the proper temperatare and the quantity small, compared to the mass of the mould, the whole of it, will be chilled, or set, in 'the hard needlelike crystals

Jan 1, 1881

C. A. ROSE, New York, N. Y. (written discussion *).-Without doubt the excellent results obtained at Ajo will cause surprise among metallurgists; 75 per cent. average capacity and 80 per cent. extraction during the first year of operation of a plant using a new metallurgical process are figures that speak for themselves. It is obvious that the most troublesome feature of the process is the fouling of solutions. The effects of this are most evident in the electrolytic tank house; but apparently the solutions are so heavily loaded with salts that their dissolving power is also impaired. This is indicated by the fact that copper comes into solution during washing after the leaching of the ore is completed, as shown by the decreasing ratio of acid to copper in the various washes tabulated in Table 4, and also by the fact that 4.9 per cent. of the total copper in the ore remains in the tailings in a soluble form. Even though the extraction in leaching and the ampere efficiency in electrolysis would be benefited by keeping the salts in solution at a lower concentration, it is doubtful whether it would pay to decrease these salts by discarding more electrolyte without other changes in the, process, since this would increase the amount of cement copper produced, which is already very large. If, however, it would not disturb the process otherwise, this object could be accomplished by increasing the range of electrolysis, so that solution going to the tank house would contain, say, 4 per cent. copper and 1 per cent. acid, and the solution returned to the leaching plant 1 1/2 per cent. copper and 4.8 per cent. acid, and by increasing the volume of solution to be discarded, this to be taken from the electrolyzed solution returned to the leaching plant. By this arrangement, more salts will be removed from the system per ton of cement copper produced; and if sufficient solution is discarded to keep the iron content down to 1 1/2 per cent. it would he feasible to recover the copper from

Jan 4, 1919

By Richard E. Ellwanger

Methods of utilizing flocculents as settling and filter aids for mineral processing slurries are reviewed. Broad chemical classifications and techniques for proper dilution, multiple addition, and combination treatments are discussed. A variety of custom built and commercially available systems for makeup and delivery of flocculents to the application points are in use throughout the mining industry. Those concepts which, in the author's opinion, are particularly important to the successful makeup and we of flocculants are presented in relationship to the available makeup and feed systems. Actual industrial applications are included in the presentation.

Jan 1, 1982