Search Documents

By M. D. Arnold, P. B. Crawford, P. C. Hall

An experimental study has been made to determine the optimum flooding pressures for four different oils. The oil formation volume factors ranged from 1.08 to 2.13, and solution gas-oil ratios ranged from about 200 cu ft/bbl to 2,250 cu ft/bbl. Viscosities ranged from 0.38 to 0.95 cp at the respective bubble points of the fluids and from 0.7 to 20 cp at atmospheric pressure. Water floods were conducted at various pressure levels from run to run. The recovery as a function of flooding pressure was found to be different for each fluid, with optimum gas saturations ranging from 7 up to 35 per cent. The data indicate that substantially higher recoveries may be obtained if water floods are conducted at an optimum pressure and that this optimum pressure is a function of fluid properties. The same core was used for all tests, and the reproduction of saturations for various runs indicates that wettability in the predominantly water-wet core did not change. INTRODUCTION A paper was presented by Bass and Crawford' which described an experimental study of the effects of flooding pressure and rate on oil recovery by water flooding. This work was conducted using high-pressure models operated in a manner similar to that of an actual reservoir, with gas saturations being obtained by a solution-gas-drive mechanism. They found that the greatest oil recovery was obtained for the system studied by flooding in the presence of a 5 to 7 per cent gas saturation. Another experimental study simulating field conditions was presented by Richardson and Perkins.' They used an unconsolidated sand pack containing kerosene-natural gas fluid and interstitial water. They flooded at various pressures and flooding rates. For their system it was found that the recovery was independent of the pressure level at which the water flood was performed. Kyte, et al," found that oil recovery by water flooding was increased as the free gas saturation at waterflood initiation was increased. However, after the initial gas saturation was increased above 15 per cent, the increase in oil recovery tended to level off. All of their runs were made at the same pressure using a light oil saturated with helium. The desired gas saturation was obtained by injecting helium into the core. Dyes' made calculations which showed that an optimum gas saturation of 12 to 14 per cent may result in an increase in oil recovery of 7 to 12 per cent over that obtained by flooding at the bubble-point pressure. Others have also found that the presence of a free gas saturation may increase the waterflood oil recovery. In each case shrinkage was small and changes in fluid properties with respect to pressure were small. A careful review of the literature reveals that at the present time there is a wide difference of opinion on the factors affecting waterflood recoveries. This diversity of opinion is probably due to the fact that very little research has been done which has taken into account the many variables existing in an actual field being water flooded. Since the literature contains little information on high-pressure waterflooding studies using various types of reservoir fluids, it was believed appropriate that such a study should be made. EQUIPMENT AND PROCEDURE All tests were made using the same consolidated sandstone core. Torpedo sandstone was used to turn a cylindrical core 13.5-in. long and with a 2.92-in. average diameter. The core had a porosity of 28 per cent and a permeability to brine of 146 md. This brine was made up by adding 20,000-ppm sodium chloride and 30,000-ppm sodium nitrite to distilled water. This was used as connate water and flooding water. No fresh water was ever brought in contact with the core, as tests showed the sandstone contained argillaceous material which swelled in the presence of fresh water and plugged the stone. The core was sealed in a section of 6-in. N-80 tubing with Woods metal filling the annulus. The core was mounted horizontally; an injection well was placed in the center of one end and a production well in the center of the other. Pressure control was maintained by placing a back-pressure regulator (upstream control) on the producing well. The "live" oil was stored in a separate bottle and water was injected into this bottle to displace the oil for saturating the core using a two-cylinder standard-proportioning pump. This same pump was used for water flooding the core at a constant rate. This system was enclosed in water jackets and the temperature was automatically main-

By C. J. Rodgers

The present day success of gravel packs to prevent or retard the migration of unconsolidated sands into the well bore is due to: (I) the use of a saline or non-aqueous, nonsolids drill fluid, (2) proper preparation of the well bore prior to gravel packing, and (3) pressure placement of the gravel. The experience gained from the "pressure pack" method of gravel packing indicates that sand-free fluid production can be maintained for a length of time sufficient to make the operation economically attractive. Data pertaining to the first 15 wells so completed by Gulf indicate that for each dollar spent to effect the completion, there will be a return of more than $2.92. The pressure pack technique of gravel packing is essentially the placing of gravel in and adjacent to the producing formations. This is done with fluid pressure and by the use of a drill fluid that will permit partial or complete loss of returns to the formation during placement. This technique was first intentionally used by Gulf in May, 1950, and since that time has been applied in more than 90 wells. Other advantages claimed for this type of completion are that the pressure placement of the gravel has a scouring effect on the casing perforations, that additional drainage channels to the well bore are created, and that the possibility of shifting of the formations adjacent to the casing is minimized and possibly prevented. During the past few years, the use of gravel to prevent or retard the migration of unconsolidated sands into the well bore has met with a favorable degree of success. Numerous methods and techniques of "gravel packing" have been used, each having its own relative merits, and with varying results. M. L. Cashion1 in 1939 ably reviewed the history of gravel packing to that time. As stated in his paper, ". .. the idea of gravel packing wells is not new." During the period 1939 to 1949, very little if any progress or change in technique in this type of completion was made. However, it was noted in some cases that during the placement of gravel, if there was a loss of drill fluid to the formation, there was a corresponding loss of gravel to the formation. Also, it was noted that in those gravel-packed completions (opposite casing perforations) that "sanded up," there was found to be an absence of gravel in the annular space between the liner and casing, although gravel had previously been placed in this space and no gravel had been removed from the well at the surface. These findings resulted in the placement of gravel with fluid pressure and by the use of a drill fluid that would permit partial or complete loss of returns to the formation during placement. Pressure placement of gravel became an accepted practice in late 1949 and early 1950. Another fact brought to light that has contributed to the current success of gravel pack completions is that drilling fluids containing solids will to some extent cause plugging of the screening medium or blocking of the producing section. The removal of these solids by chemical action, mechanical action, or a combination of the

Jan 1, 1955

By J. W. Downey, A. E. Dwight, R. A. Conner

In a previous paper' we have reported the existence of a number of AB2 Laves phases in which A is a member of the scandium group (including the 1an-

Jan 1, 1967

By O. M. McRae. Discussion by R. W. Jones

R. W. Jones (Senior Exploration Geologist, Standard Oil Co. of California, Box 250, Seattle, Wash.) -Mr. McRae6 and his colleagues are to be congratulated for providing a more coherent structural synthesis of the complex structure in the Courtland-Gleeson area, Cochise County, Arizona, than the "gigantic thrust breccia" concept of Gilluly. 4 However, a few problems of interpretation remain. It is the intent of this note to point out some of these problems, and, drawing on my own work in the area as well as the work of McRae6 and Gilluly, 4 to suggest some interpretations which differ from those previously published. GRAVITY SLIDES In an unpublished manuscript (Jones5) I previously argued that most of the complex structures in the Courtland-Gleeson area can be most reasonably interpreted in terms of gravity sliding caused by uplift and eastward tilting of Jurassic intrusives and associated Paleozoic rocks. Although the field work and drill hole data described by McRae6 provided excellent documentation for two important gravity slides, McRae6 interpreted the basic structure in the Courtland-Gleeson area in terms of major eastward directed thrusting. I continue to disbelieve the

Jan 1, 1967

By M. Shelef, A. W. Fletcher

The effect of alkali sulfates in promoting the sul-fation of nickel and copper in a bulk sulfide flota -tion concentrate by fluidized bed roasting has been studied in the laboratory, and it was shown that the various alkali sulfates promote sulfation to approximately the same extent. The sulfation of a mixture of synthetically prepared iron and nickel oxide and of nickel ferrite has also been studied. Nickel sulfation was promoted by high ratios of Fe:Ni and by the presence of sodium sulfate. THE work described in this paper was a continuation of earlier studies into the role of alkali sulfates in promoting the sulfation roasting of nickel sulfides1,2 in an endeavor to determine how the system was affected by the presence of compounds of iron and copper. The earlier work1 showed that, in the sulfation of NiO at 680°C, the reaction was limited by the formation of an impermeable film of nickel sulfate on the oxide surface. The relative effect of the various alkali sulfates in promoting nickel sulfation varied in the order: Li > Na >Cs > Rb > K A study of alkali sulfate/ nickel sulfate interactions at high temperatures showed that the promoting action was due to the fact that the nickel sulfate product layer sintered and agglomerated only when the more active additives were present. This resulted in the formation of discontinuities in the nickel sulfate layer so that diffusion of the sulfating gases to the NiO surface was no longer impeded and the reaction could proceed to completion. A similar explanation was used for the observation that sodium and lithium sulfates promote the oxidation of NiS to NiO at temperatures below 750°C since small amounts of nickel sulfate were formed during oxidation.2 It was of interest to study the effect of alkali sulfates on the sulfate roasting of a sulfide flotation concentrate which is typical of material treated commercially. In order to control temperature it is essential to roast sulfides in a fluidized bed and this technique was therefore used, although the batchwise operation of a small-scale laboratory reactor does not reproduce all conditions which prevail in full-scale continuous plant. The results obtained are therefore only comparative, and cannot be used for predicting the optimum conditions for metal extraction. The sulfation of synthetically prepared mixed oxides of nickel + copper and nickel + iron and of nickel ferrite was also studied to evaluate the relative effects of alkali sulfates with more complex systems. SULFATION ROASTING OF A SULFIDE FLOTATION CONCENTRATE The bulk sulfide flotation concentrate used in this work contained 7.92 pct Ni, 1.74 pct Cu, 35.66 pct Fe, and 31.28 pct S. The sulfide minerals present in order of abundance were pyrrhotite FeS, pyrite FeS2, pentlandite (FeNi)S, and chalcopyrite CuFeS2. Two samples described as coarse and fine were used. The coarse sample, which was a flotation concentrate (58 pct plus 300 mesh), was ground to 100 pct minus 350 mesh to produce the fine sample. Before roasting, the sample of sulfide concentrate was agglomerated by wetting witli a solution of the alkali sulfate (or water), thoroughly mixing, and drying at 110°C. This gave a cake which was gently crushed and screened, the -18 +100 mesh fraction being used for fluidized bed roasting. A similar-size fraction had been used by the authors in pilot plant work with a 4-in.-diam fluidized bed reactor.' In this work it was found that the molar ratio of additive to the total iron + nickel + copper content of the sulfide sample should be adjusted to a value of approximately 0.06, as this was the optimum amount necessary for nickel sulfation. Experimental. The fluidized bed reactor consisted of a quartz tube approximately 60 cm long and 30 mm in diameter resting in a vertical tube furnace. The sulfide bed (30 g) was supported on a bed of -4 +12 mesh quartz particles 3 cm high, which rested on a sintered quartz disc welded to the tube. The temperature of the furnace was controlled with a variable transformer to give a final bed temperature of 680°C. The bed was fluidized with air or mixtures of air + 10 pct v/v SO2, at a total apparent gas velocity of 60 to 65 cm per sec at 680°C. The SO2 was introduced into the fluidizing air stream only when the oxidation of the sulfides was completed. At the end of the roasting period the calcine was leached with boiling water and the

Jan 1, 1964

By S. Gilbert, G. R. Bailey

A further evaluation of the bomb-sampling method for determining the oxygen content of liquid steel is presented. The results of this study and their close agreement with the results of an earlier evaluation confirm the conclusion that the bomb-sampling method is valid for obtaining representative samples for the determination of the oxygen content of a liquid steel bath. WHAT constitutes the most desirable procedure for obtaining a sample suitable for determining the oxygen content of a liquid steel bath has been a controversial subject for several years. In 1952 Huff, Bailey, and Richards' described a modification of the bomb-sampling technique originated by McCutcheon and Rautio.' In both the modified and original techniques, a small cast-iron or steel mold containing aluminum wire and appropriately covered is inserted into the furnace, coated with slag, and then plunged into the metal bath. Upon entering the metal, the cover melts and a sample of the steel bath enters the mold. The data presented by Huff, Bailey, and Richards' indicated that reproducible samples could be obtained by their method. Furthermore, the oxygen analyses from samples obtained by their method agreed better with those from controlled laboratory experiments than did analyses from samples obtained by methods previously suggested for sampling large liquid-metal baths. Most techniques, other than bomb-sampling, require that a sample of liquid steel be removed from the furnace in a well slagged spoon and poured into an iron mold containing aluminum or into a massive copper mold for rapid chilling. Pouring in this manner requires that the sample pass through the air. The controversy, then, is somewhat as follows: Proponents of the spoon-sampling method and similar dip-and-pour methods feel that the introduction of a cold steel mold into a molten steel bath may result in a localized boiling condition that may deplete the steel of oxygen to a significant degree in the area where the bomb is introduced. Conceivably this boil could cause results that are, on the average, too low and nonrepresentative of the bath composition. On the other hand, samples that are spooned and then poured through the air may also be nonrepresentative because of oxidation by the atmosphere. The restrictions imposed in sampling with a spoon are much more stringent than those imposed when sampling with the bomb-type mold within the furnace. The spoon sample must be taken in a well slagged spoon, a requirement that depends on the condition of the slag in the furnace. Also, the samples must be poured as quickly as possible, without shaking the spoon and without allowing slag to enter the mold. The necessity of fulfill-

Jan 1, 1955

By Persifor Frazer

The '(author's edition" of the following paper, "subject to re vision," was received by him, and copies sent to Professor Geikie and others about two weeks before the date of the meeting at which it was to be read. A telegram, and subsequently a letter (both of which unfortunately arrived too late), apprised the present writer that the Director General objected to certain views ascribed to him as the reverse of those which he really held. These views, however interesting, had no very important bearing on the object of the fol lowing notes, which, as must be evident, are devoted to the conside ration of the close analogies between the Welsh and American rocks. Without being able, therefore, to account for the circumstance which Professor Geikie has mentioned, it is thought better in the present revised edition to omit all allusion to Professor Geikie, or Mr. Peach, or their views, except in this place, where I desire to thank them for their courtesy during the time which I had the pleasure of spending in their society. It appears sufficiently throughout the body of the paper that the writer had not the slightest intention of entering the controversy, which was about to commence, concerning the proper horizons of the St. David's rocks, for many reasons; and amongst others because he did not feel that a sojourn of a few days in a difficult region, which had been already studied by many of the foremost geologists of England, would warrant him in adding to the literature on the sub ject. The discussion of the analogies between these rocks and those of the Eastern Appalachians, which he has studied for twelve years, of which eight were spent in the service of the Second Geological Survey of Pennsylvania, was much more to his taste as it was more within his ability, and if he has added anything to the evidence of these analogies, the paper, however imperfect, will not have been written entirely in vain. Right or wrong, he assumes the entire responsibility of what follows.

Jan 1, 1883

By T. L. Johnston

MUCH has been said and written about deep mine shafts and deep drill holes as man in his search for mineral wealth digs deeper into the earth's crust. Each year some new extra depth is heralded as a record, but with unlimited possibilities of going still deeper. In contrast to "digging deep," "mining high" is limited by the height of the mountains (Mt. Everest being the maximum with its 29,000-ft. elevation) and also by the extent of human endurance. An ex- ample of what might be called near- stratosphere mining in what is probably the highest mine worked by compressed air in the world is seen in a recent project in the Andes mountains of southwestern Bolivia.

Jan 1, 1939

By N. Van Wingen

EFFECTIVE sand permeabilities can be ascertained from core analysis if the laboratory data are compensated to allow for the presence of connate or residual water. Such adjustments can be made by applying empirically derived correction factors. Effective sand permeabilities can be estimated also from analytical studies of field depth-pressure measurements. In one method the time rate of pressure build-up after a well is shut in from steady-state flow is required, and in the other the direct measurement of a steady-state rate of flow and the corresponding equilibrium pressure. The results of the investigation discussed in this paper demonstrate that these methods for determining mean effective sand permeabilities can be correlated.

Jan 1, 1942

By Gregory Comstock

THERE is a growing interest in the possibilities presented by the manipulation of metal powders, which justifies an attempt to summarize their character and potential value. A summary of this kind presents an opportunity for making a classification of metal powder products into several general types. Our present knowledge of the finer and more abstract aspects of many of the principles involved in metal powder technique is extremely limited. Any conclusions as to the ultimate value of the process will, therefore, for the present at least, be of doubtful value unless they are substantiated by its products. The number of such products is increas-ing. A study of their diverse and unusual characteristics; an examination of the methods by which they ale made, and a consideration of the reactions that take place during their fabrication, in so far as we can define them, should afford as good an evaluation of this interesting development as it is possible to make at this time. A critical study of this kind results in a formidable list of special attributes, which apparently are characteristic of applied powder metal-lurgy. A comparison of these special effects with the end products and well defined limitations of the melting and casting process indicate that often they may very well be considered as being special advantages. They are subject, of course, to certain not as yet so well defined limita-tions of their own. Based on current products only, a necessarily con-densed summary of the more striking special attributes of the metal powder process follows.

Jan 1, 1938

By R. W. Mancantelli, J. R. Woodward

In 1947 a large low grade deposit of uranium was located in the northwest corner of Saskatchewan, in the Beaverlodge property of Eldorado Mining & Refining Ltd. Most of the values occur as thin seams and as coatings on other minerals, and the ore, which is light and friable, is not amenable to the usual gravity methods of concentration. The acid leaching process developed to retreat the company's Port Radium tailings was also impractical, as the percentage of carbonates is high and the percentage of sulphides relatively low. Construction of the mill building and installation of equipment, both scheduled for 1952, awaited selection of a satisfactory ore dressing process on or before Oct. 1, 1951. An extensive research program on dressing of ores from the Ace mine therefore was undertaken by the Mines Branch in Ottawa, a research team at the University of British Columbia and an ore dressing group at the company's Port Hope refinery.

Jun 1, 1955

The Subcommittee on Manganese, of the A.I.M.E. Committee on Industrial Preparedness, prepared under date of Jan. 24, 1924, for and at the request of the War Department, a confidential report on manganese as an element in the problem of national defense. This report was later released and published, in slightly modified form, as a separate pamphlet. After the lapse of eight years, in view of the vital position of manganese in the problem of industrial preparedness agenist a war emergency, the War Department made a request to have the onclusions of 1924 reviewed and brought up to date. To comply wi' this request the manganese subcommittee was reconvened and ex' tive studies were once more made of the entire subject of mang? . A new report, with specific recommendations, was submitted + War Department in February, 1932. This second report, with 4. L specific conclusions and recomrnendations expressed to the War Department omitted, has now been released and is hereby published. Following a rather brief discussion of uses of manganese and classification of manganese ores, requirements and sources are dealt with at some length. Domestic ferro-grade reserves are estimated on the basis of price and are shown by means of a curve where tons of metallic manganese are plotted cumulatively against prices ranging from 50¢ to $1.00 per unit; thereby indicating at a glance the tonnage which the Committee believes would become commercially available at any particular price per unit. Foreign sources of ore are described and foreign prices which the domestic producer must meet are considered. The question of a war-emergency reserve is then analyzed, requirements are balanced against apparent resources, and the principal conclusion that emerges is that a war reserve or stockpile is still vital to national defense.

Jan 1, 1934

By Robert W. Thomas

LEACHING of mined-out areas at the Arizona property of the Ray Mines Division, Kennecott Copper Corp., was started on Jan. 20, 1.937, and by July 1, 1938, 10,000,000 lb. of copper had been produced by this method. Leaching operations at present are confined to the western portion of the ore body and over an area of approximately ten acres. The ore in this area was extremely high in pyrite and the copper content, which averaged slightly in excess of 1 per cent, was the result of incomplete secondary enrichment by solutions which apparently worked laterally from the main ore body. Above the ore was an unaltered zone of primary or protore averaging 125 ft. in thickness and containing approximately 0.6 per cent copper. Above this was the capping or leached zone averaging 50 ft. thick.

Jan 1, 1938

By Kiyoshi Azuma, Hiroshi Kametani

Dissolution of a ferric oxide in acid solution is divided into two different types In the accelerated type dissolution proceeds in three stages 1) an inittal reaction during which the dissolved amount of oxide is nearly proportional to the cube root of time ; 2) an accelerated reaction: and 3) a final stage during which dissolution approaches completion. This course of dissolution gives an S-shaped curve in the above sequence OH a log weight percent of dissolved oxide against log time graph. In the parabolic type dissolution proceeds in four stages: first and second stages similar to those of the accelerated type; 3) parabolic-rate dissolution during which the dissolved amount of oxide is nearly proportional to the square root of time: and 4) a final stage. The effect of the kind of acid, the temperature of solution, and the concentration of acid was investigated. The results are discussed and a rate equation is proposed. AN attempt has been made to obtain some information on dissolution of a ferric oxide in various acid solutions. In view of hydrometallurgical processes the dissolution of ferric oxide is of less importance than that of zinc oxide or copper oxide in general. One of a few processes which intend to dissolve ferric oxide is an elimination of iron impurity from acid-insoluble materials. However, most leaching processes of oxide ores and cinders are accompanied with more or less dissolution of iron. According to Pryor and Evans1 the rate of dissolution of a ferric oxide in various acids decreased in the order of hydrofluoric acid > hydrochloric acid > sulfuric acid > perchloric acid. This order was in accord with the order of decrease of the complexing affinity of the anion for ferric ion,

Jan 1, 1964

By W. H. Ode, W. A. Selvig

By plotting fixed carbon against British thermal units of coals free from mineral matter, and ranging in rank from anthracite to lignite, it is found that the coals of higher rank, from anthracite to the higher rank of the high-volatile bituminous coals, inclusive, can be separated into groups according to their degree of metamorphism by reference to their fixed carbon. Such charts show also that the coals lower in rank can be best separated into groups with respect to B.t.u., especially when plotted on the moist basis, that is, coal containing its natural bed moisture. A tentative scheme for coal classification was presented at the October, 1932, meeting of the Technical Committee on Scientific Classification, of the American Standards Association Sectional Committee on Coal Classification. This scheme was sponsored by Subcommittee IV on Tentative Classification of Coals, under the chairmanship of W. T. Thom, Jr. It proposed the grouping of coals according to rank by reference to fixed carbon and B.t.u., on the basis of coal containing its natural bed moisture but free from mineral matter. This scheme proposed classifying coals into four broad classes: (1) anthracitic, (2) bituminous, (3) subbituminous, (4) lignitic. The anthracitic class was divided into three groups designated as meta-anthracite, normal anthracite, and semianthracite. The bituminous class also was divided into three groups, low volatile, medium volatile, and high volatile. The high-volatile group was further subdivided into four subgroups according to moisture content, as fo1lows: (1) less than 5 per cent, (2) 5 to 10 per cent, (3) 10 to 15 per cent, and (4) 15 per cent and more. The subbituminous class was divided into two groups, group 1 including subbituminous coals having calorific values of 10,500 B.t.u. or more, and group 2 including those with less than 10,500 B.t.u. The lignitic class of coal was divided into two groups both below 8,000 B.t.u., the one group consisting of consolidated and the other of unconsolidated

Jan 1, 1934

By M. C. Cheney

The active development of the vast East Texas oil field, the attendant effects of the rapidly increasing flow from its prolific wells and the efforts to bring order out of chaos precluded or dwarfed other oil development in Texas during 1931. In a paper by Dr. F. H. Lahee1 presented at the October, 1931, meeting, the early history of the East Texas oil field is described and the sequence of events in connection with its development and efforts to control its production up to Sept. 25 is narrated. At that time the Railroad Commission of the state reduced the production of the field to a maximum of 400,000 bbl. per day by restricting the allowable daily production per well to 185 bbl. By further reduction in the daily production per well to 100 bbl., the field was held below that maximum figure during the remainder of the year. Meanwhile, as a result of an injunction against the Railroad Commission, its authority in the field was superseded on Oct. 13 by the Governor of the state, and after that date production was controlled directly by his orders issued under authority of martial law. Suits to contest this authority were brought in the Federal courts and were pending at the close of the year. On March 5, 1931, as a result of the East Texas production, posted prices for Mid-Continent 40' A.P.I. crude slumped from $1.07 to $0.67. As East Texas production continued to mount, posted prices in East Texas were reduced to $0.37 on June 3 and $0.22 on July 8, although in that field most of the oil was sold for much less, bringing the producer and royalty owner as low as $0.025 per barrel. Northeast Texas To the information contained in Dr. Lahee's paper, it can now be added that the East Texas field has produced over 105,000,000 bbl. and registered about 3700 successful completions during 1931. There may be some merit to the recent prediction that a large part of the field will have passed its flowing period by the middle of 1932 unless

Jan 1, 1932

By Robert Ammon

THE purpose of this paper is to present a brief sketch of the development of this hindered-settling classifier, but primarily to show the actual results obtained in practice with the classifier working on the Butte copper ores at the Boston & Montana Concentrator, at Great Falls and the Washoe Concentrator at Anaconda. The writer has endeavored to be as brief as possible, giving only the essential figures showing the efficiency of the classifier and leaving considerable interesting information to be derived by the reader from the statistics given. The paper deals with the practical work of the classifier under the following heads: 1. Desliming 4.0-mm. primary feed, overflow from 0.07 to 0.0 mm. 2. Desliming 1.25-mm. secondary feed, overflow from 0.07 to 0.0 nun. 3. Desliming Huntington Mill discharge, overflow from 0.07 to 0.0 mm. 4. Classifying 2.5-mm. deslimed secondary feed, overflow from 1.00 to 0.07 mm. 5. Classifying 2.5-mm. deslimed primary feed, overflow from 0.75 to 0.07 mm. 6. Classifying 4.0-mm. deslimed primary feed, overflow from 0.75 to 0.07 mm. 7. Classifying middling-tailing product from roughing tables, overflow coarse tailing. 8. Classifying 2.5-mm. trommel undersize, not deslimed, overflow from 0.75 to 0.0mm. 9. Remarks on the inner feel cone. In the following pages all overflows, are given in quartz dimensions; i.e., by a 0.75-mm. overflow 'is meant an overflow whose maximum particle is a 0.75-mm. quartz grain. By the term "slime" is meant all material which will pass through a 200-mesh screen whose average opening is 0.07 mm.

Jan 8, 1913

By Robert Ammon

The purpose of this paper is to present a brief sketch of the development of this hindered-settling classifier, but primarily to show the actual results obtained in practice with the classifier working on the Butte copper ores at the Boston & Montana Concentrator at Great Falls and the Washoe Concentrator at Anaconda. The writer has endeavored to be as brief as possible, giving only the essential figures showing the efficiency of the classifier and leaving considerable interesting information to be derived by the reader from the statistics given. The paper deals with the practical work of the classifier under the following heads: 1. Desliming 4.0-mm. primary feed, overflow from 0.07 to 0.0 mm. 2. Desliming 1.25-mm. secondary feed, overflow from 0.07 to 0.0 mm. 3. Desliming Huntington Mill discharge, overflow from 0.07 to 0.0 mm. 4. Classifying 2.5-mm. deslimed secondary feed, overflow from 1.00 to 0.07 mm. 5. Classifying 2.5-mm. deslimed primary feed, overflow from 0.75 to 0.07 mm. 6. Classifying 4.0-mm. deslimed primary feed, overflow from 0.75 to 0.07 mm. 7. Classifying middling-tailing product from roughing tables, overflow coarse tailing. 8. Classifying 2.5mm. trommel undersize, not deslimed, overflow from 0.75 to 0.0 mm. 9. Remarks on the inner feed cone. In the following pages all overflows are given in quartz dimensions; i. e., by a 0.75-mm. overflow is meant an overflow whose maximum particle is a 0.75-mm. quartz grain. By the term "slime" is meant all material which will pass through a 200-mesh screen whose average opening is 0.07 mm. The development of the classifier was commenced in the fall of 1910,

Jan 1, 1914

By OTTO HERRES

TO operate the bituminous coal industry in the United States in 1929 cost $770,237,000, of which $30,739,000 was paid for purchased power and $34,947,000 for new machinery and equipment. Equipment aggregated 3,124,000 hp. A mining industry that spends $65,000,000 a year for power and machinery is likely to be fairly well mechanized, and when the machinery in use takes three million horsepower to drive it, the probabilities are that mechanization has been in progress in at least some of the mines for quite a few years. Mechanization in its broadest sense implies machine cutting, power drilling, mechanical loading, electric haulage, mechanical sizing and cleaning, and lesser applications of machinery to mining operations. But the introduction and development of mechanical loading has been the feature of coal mining recently and its extraordinary progress is causing great changes within the industry. First, let us look at the records. The quantity of coal loaded mechanically in bituminous mines was:

Jan 1, 1933

By N. J. Grant, D. S. Bloom

N recent reports, Sully' and Beck and coworkers' I have advanced hypotheses concerning the formation of the phase. Both of these hypotheses are based on Pauling's theories of the electronic configuration of the elements of the first transition group. Sully considered that the number of electrons which can be absorbed in filling electron "holes" is the factor which determines whether or not the structure can form. Beck suggested that the presence of a certain concentration of electron "holes" is the controlling value. It can be shown that a similar criterion can be developed without making reference to Pauling's theories. Table I shows the elements of the first transition group and the incidence of the a structure in the binary systems of these elements according to the data presently available. Also appended is the number of electrons considered to exist in the 3d-4s levels of these elements. If the atomic percentages for the phase are listed as shown in Table 11, and if the number of electrons in the 3d-4s levels per atom is calculated for the a boundary values, the results are as shown in the last column. It can be seen that the numerical values are all in the vicinity of 7 electrons per atom. This is true also for the ternary Cr-Mo-Ni IT phase, which occurs in a system in which none of the binary compositions are known to develop the phase. In the Fe-Mo binary, the high temperature a phase, which occurs at a composition of 50 atomic pct of each element, also yields a ,;1 e of 7 electrons per atom. From inspection of Tables I and 11, it develops that any series of sequential numbers which is assigned to the elements under consideration will result in the numbers pertaining to a compositions grouping themselves around one specific number. It does not follow, however, that this random number necessarily has physical significance. Such a point has already been discussed by Hume-Rothery." One interesting point develops from this study, however, and that is the position of manganese with reference to the other elements and to the phase. In the system used here, the formation of phase is associated approximately with the value of 7 electrons per atom, which is also the number of electrons per atom that manganese has. Manganese, it will be recalled, exists in three different crystal forms, none of which are the usual, simpler metallic forms; on the other hand, elements just to the left of manganese (in Table I) generally have lower coordination-number structures (body-centered cubic) than do elements to the right of manganese (face-centered cubic). The contribution to a complex crystal structure by the interalloying of elements from opposite sides of manganese is significant in that the a phase is formed in binary systems including one element from each side of manganese, with manganese capable of participating with both sides. It is indeed an interesting coincidence that manganese, with 7 electrons per atom, solidifies in complex crystal forms, and that when alloys of the transition elements are made which have seven 3d-4s electrons per atom, they, too, tend to assume a complex crystal form. From the above, it might be deduced that the study of the a phase might be advanced by a critical examination of the element manganese and how its structure is affected by small additions of elements which change the 3d-4s electrons per atom number. The role of atom size would also be of interest in formation. References ' A. H. Sully: The Sigma Phase in Binary Alloys of the Transition Elements. Journal Inst. Metals (1951) 80, Part 4, p. 173. 2 S. Rideout, W. D. Manly, E. L. Kamen, B. S. Lement, and P. A. Beck: Intermediate Phases in Ternary Alloy Systems of Transition Elements. Trans. AIME (1951) 191, p. 872; Journal of Metals (October 1951). "W. Hume-Rothery, H. M. Irving, and R. J. P. Williams: The Valencies of the Transition Elements in the Metallic State. Proc. Royal Soc. (September 1951) 208A. p. 431.

Jan 1, 1954