Search Documents

By F Gervilla, J Laukkanen

The Kevitsa Ni-Cu-PGE deposit in northern Finland contains disseminated Ni-Cu-Fe sulfides, and platinum-group minerals (PGM). The 2.05 Ga-old ultramafic-mafic, funnel-shaped intrusion is intruded into a volcanosedimentary sequence. The major ore minerals are pentlandite, hexagonal pyrrhotite and troilite, chalcopyrite, cubanite and magnetite. Pyrrhotite and pentlandite are replaced by pyrite, millerite and heazelwoodite near the surface. Nickeline, maucherite and gersdorffite are locally abundant. A pilot feed sample of 575 t of the main orebody at Kevitsa had average grades 0.45 per cent Cu, 0.36 per cent Ni, 1.85 per cent S, 0.33 g/t Pt, 0.34 g/t Pd and 0.19 g/t Au, with 0.06 per cent Ni contained in silicates. Higher PGE contents (2 - 27 ppm) occur in a vertical N-S bearing fault zone. The PGM (n = 6022) mapped in specimens of four drill holes, consist of sperrylite 34.7 vol per cent, braggite and cooperite 18.5 vol per cent, geversite 17.2 vol per cent, moncheite 14.7 vol per cent, merenskyite 6.7 vol per cent, stibiopalladinite 4.3 vol per cent, sobolevskite 1.9 vol per cent, kotulskite 0.7 vol per cent, michenerite 0.6 vol per cent, keithconnite 0.3 vol per cent, rustenburgite 0.1 vol per cent, melonite, froodite, laurite together 0.1 vol per cent and only a few grains of sudburyite, irarsite, vysotskite, erlichmanite, hongishiite, Pt-Cu-alloys, three undefined Pd and Pt bismuthinides and antimonides and a Pd-Cu-bearing Pt-Ni-Fe sulfide. Most of the PGM, 62 per cent, are enclosed in silicates, 29 per cent are intergrown with sulfides, nine per cent are within sulfides. A portion of the PGE occurs in solid solution in sulfides and arsenides. Ni flotation yielded smelter-grade concentrates averaging 12.2 per cent nickel. The average sulfide Ni recovery is 78.8 per cent and total Ni recovery is 65.3 per cent. The average Pt is 10 g/t at 55 per cent recovery, Pd 7.7 g/t at 38 per cent recovery and Au 1.6 g/t at ten per cent recovery. Cu concentrates averaged 28.6 per cent Cu with an average recovery of 78 per cent and further 11 per cent in the nickel concentrate. The copper concentrate contains 4 g/t Au at 24 per cent recovery. The average Fe to MgO ratio 17.9 is well above the targeted minimum of 4.5. The pilot results show that the previously used TETA (triethylene tetramine) can be avoided and good quality, smelter-grade concentrates can be produced from the Kevitsa ore at economical levels of recovery by conventional flotation methods.

Jan 1, 2008

By M Zengerer

The Basil Cu/Co deposit comprises a 26.5 Mt Inferred Resource of copper and cobalt, grading 0.57?per cent Cu and 0.05 per cent Co. It lies in the Harts Range, Central Australia, within the Riddock Amphibolite of the Irindina Province. Analysis of drilling within the mineralised zone of the deposit determined a spatial association between pyrrhotite with high magnetic susceptibility and chalcopyrite, following a strong magnetic trend as determined from airborne geophysics. A study was commissioned to examine if geophysical inversion could predict the distribution of sulfide mineralisation based on pyrrhotite from drill hole intersections, as well as predicting further mineralisation at depth or in the vicinity of the deposit. Petrophysical and geostatistical analysis of drilling susceptibility and mineralisation provided a basis of property distribution inside the model. This was followed by 3D geological modelling of mineralisation based on domain kriging of drill hole susceptibility sensitivity testing of signal to source depth, and distribution was performed using 3D forward modelling. Stochastic inversion generated alternative 3D geological models, which were tested for behaviour and adherence to observed drilling data and geostatistical limitations using GeoModeller software. Predicted mineralisation distribution was compared with conventional geostatistical modelling and found to be in agreement in planar behaviour but exhibiting possibly isoclinally folded trends, with reliability increasing closer to the surface. Predictions of mineralisation at greater depth and beneath weaker anomalies were more diffuse due to small model cell size having limited influence on the signal at depth.The Blackbush uranium deposit comprises a 64.5 Mt Inferred Resource, grading 230 ppm U in the Pirie Basin south of Whyalla, South Australia. It directly overlies the radiogenic Samphire Granite and is considered a tertiary unconformity deposit. Sensitivity modelling was performed using high-resolution ground gravity to see if a deposit signature could be detected using gravity. This required 3D implicit modelling of the geology and mineralisation from drill hole data and characterisation of an associated physical property model using domain kriging in GeoModeller. Density models relied on exploiting an observed relationship between logged density and measured uranium oxide percentage. The residual gravity response of the background geology model identified the location of the uranium deposit. Stochastic inversion of the litho/property 3D model has refined the known distribution of uranium from drilling and provided structural insights into the deposit.These projects have become excellent case studies for exploiting the relationship between mineralisation and potential fields and for testing the applicability of using domain kriging of properties determined from drilling to build robust 3D geological models for stochastic geophysical inversion, leading to robust methods for exploration targeting and mineral deposit prediction.CITATION:Zengerer, M, 2014. Use of geostatistically-constrained potential field inversion and downhole drilling to predict distribution of sulfide and uranium mineralisation, in Proceedings Ninth International Mining Geology Conference 2014 , pp 281–290 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 18, 2014

By A G. L Pratt, J R. Grant

Mining companies face the ongoing challenge of sustaining and growing production. This paper outlines business investment concepts to grow reliable returns on investment from a portfolio of choices by:improved visualisation, diagnosis and tune up of the investment pipeline (pipeline management); good corporate decision making (governance) to select the right project mix, risks and sequence; and delivery strategies to enhance and reliably execute projects.

Jan 1, 2006

By J T. Sharp, M A. Styler, D McGowan, P W. Mayne

Static liquefaction is a geotechnical hazard in mine tailings facilities. Soils that are contractive in shear are susceptible to static liquefaction. Tailings facilities are dynamic structures, typically growing in height each year. Dilative tailings may become contractive under increased effective stress. In this paper we show that Cone Penetration Test (CPT) data can be used to estimate the future state of in-place tailings under changes in effective stress. Susceptibility to static liquefaction is typically evaluated with the CPT by using a clean-sand equivalent normalized cone tip resistance (Qtn,cs) or by estimating the state parameter (?). An alternative approach is to evaluate the soil-state using the yield-stress-ratio (YSR = ?’y/?’v0). If the YSR equals one it is on the normal consolidation line and the soil-state is contractive. YSR values greater than three are typically dense of the critical state line (CSL) and the soil-state is dilative. In this paper we review how to calculate Qtn,cs, ?, and ?’y; and how the YSR can be used to screen for contractive soil behaviour. Unlike Qtn,cs and ?, it is very simple to estimate how the YSR will change due to an increase in overburden stress. This YSR approach was evaluated at three locations that saw increases in overburden of 10 m, 20 m, and 25 m. We show that the ?’y calculations are consistent and the increase in effective stress moves the soil state towards looser soil states. CITATION:Styler, M A, Mayne, P W, McGowan, D and Sharp, J T, 2018. Predicting changes in static liquefaction susceptibility using cone penetration test results, in Proceedings Mine Waste and Tailings Stewardship Conference 2018, pp 317–332 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 23, 2018

By Y X. Xue, J Pan, D Q. Zhu

In order to reveal the correlation between the fundamental sintering characteristics of iron ores and their real sintering behaviours, a comprehensive evaluation index is proposed based on the measurement of four high temperature indexes, ie assimilation temperature, liquid phase bonding strength, liquid fluidity and calcium ferrite formation percentage, and the sintering pot tests of single ore fines and their blends. The results show that both the lowest assimilation temperature and liquid fluidity of ore blends appear to be the linear superposition of those of single iron ores except for the liquid phase bonding strength and calcium ferrite formation percentage. Furthermore, the tumble index of the sinter product obtained from blended iron ores also corresponds to a linear superposition of that of single ores, but not for the solid fuel rate and productivity. The comprehensive strength index YT exhibits a credible linear positive correlation with the four high temperature reactivity indexes, whereas the comprehensive productivity index YP possesses a lower correlation with the four high temperature reactivity indexes. The comprehensive strength index YT developed can predict the tumble index of the sinter product quite well, but the comprehensive productivity index YP cannot be used to evaluate the productivity effectively.CITATION:Zhu, D Q, Xue, Y X, Pan, J and Shi, B J, 2017. Correlation between high temperature sintering characteristics and sintering behaviours of iron ore fines, in Proceedings Iron Ore 2017, pp 123–132 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By D K. Weatherley, G R. Ballantyne, S Ali, M Yahyaei, M S. Powell

This paper explores development of a novel ore characterisation method for the precise measurement of practical minimum comminution energy. A monolayer of particles with a narrow size distribution is broken using a precision rolls crusher (PRC); an ore characterisation device developed to overcome the shortcomings of conventional tests. For energy measurement, PRC uses two shaftmounted rotary torque transducers. These transducers acquire precise torque and angular speed data in response to the load applied to the rotating shafts during breakage events, which is converted into energy. The test progressively crushes feed particles down to final product size in many controlled breakage stages. The generation of fines in each breakage stage is then plotted as a function of input energy. The inverse of the gradient of this plot provides the size specific energy (SSE) in kWh/t of material generated below a predefined marker size; -75 μm in this case. The PRC has potential to evolve as a geometallurgical ore characterisation test—it is simple, fast, requires small sample mass (200–300 g), covers a wide feed particle size range (10 mm to 115 µm), and provides ideal SSE measurements that can be used for the calibration of on-site production equipment.

Aug 24, 2022

By V Chamberlain, M Appeah Owusu, M Aniawu-Asumakah, A Anyimadu, R Peattie

This is an integrated geology and plant improvement study arising from the heterogeneity seen in mineralogy and gold association at the Obuasi goldmine in Ghana. This heterogeneity comes from the two ore types mined, the one being a sulphide ore, mainly composed of gold-bearing arsenopyrites. This gold is refractory and exhibits a strong relationship between gold and As. The other is quartz veins, that are high grade and free milling. The installed circuit consists of comminution – Gravity -Flotation – BIOX – Leaching and Adsorption processes. The opportunity tested involved improved mass pull - related flotation recovery of Au in the Sulphide stream; while balancing the need for a minimum Sulphide grade for the Bio-oxidation process, occasioned by the removal of 25 to 30 % of the (quartz) stream through preconcentration by Ore sorting. The current circuit is then utilized for the sulphide route, while a smaller grind-gravity circuit is utilised for the quartz stream in a relatively inexpensive way, followed by a common leaching and adsorption circuit. Added advantages of the strategy includes faster recovery of gold from the quartz stream, with less consumption of reagents from saving on flotation and BIOX reagents for this stream. Screening and Ore sorting was successfully tested with laser technology, achieving over 98% separation of quarts (containing up to 40% of the gold). The plant schedule of Ore, the suggested circuit design for the Ore sorting, the results obtained from the different flotation regimes, as well as consequent financial modelling have been presented and discussed in this paper. This illustrates the opportunity that arises out of a detailed analysis of material versus installed circuits, even if the gains in pre-concentration do not necessarily involve rejection of gangue material. An added opportunity for future investigation, briefly discussed but not tested in this paper, would be to maintain current mass pulls but with increase in throughput (by the space created by the sorted material). This will of course require the mining ability. It could also add LOM value by altering the cut-off grade.

Nov 10, 2020

By P M. Black, T Itaya

Arc-type volcanic activity has been a major feature of the late Cenozoic geological evolution of the Pacific-Australian plate boundary in the northernNew Zealand region. The time/space distribution patterns of arc-type rocks reflect changes in the nature of the plate boundary as it has evolved. Inception of volcanism began in the north during earliest Miocene times (26 Ma) following ophiolite emplacement and during the next 10 Ma developed into a volcanic arc segment extending south to the present position of the central North Island. The northern part of the arc became extinct about 15Ma ago, but activity continued in the central (Coromandel) part of the arc until about 5 Ma ago. In late Pliocene and Quaternary times volcanic activity has become concentrated in a northeast trending zone which is collinear with the Tonga-Kermadec Arc.   These time/space patterns can be interpreted in two ways. Firstly, if relative plate motion was essentially transform in the region prior to 26 Ma then a small change in the relative plate vectors may have initiated subduction and the associated volcanism. Southward evolution of the arc can then be seen as the straightening and extension of a single arc. Alternatively, the distribution of volcanic rocks can be interpreted as the capture of a relatively short lived arc by southward migration of the dominant Tonga-Kermadec subduction system.

Jan 1, 1995

By Atalla YM

Steel rolling mill product finishing pro cesses gradually become or often already are unsuited for current production and marketing conditions. Indications are made as to what has been done to (i) rectify situations of this kind and, (ii) to reduce both product finishing time and costs. The principal features of two separate case studies are reviewed, these being (a) the finishing-end of B.H.P.'s Newcastle o.2 Merchant Mill and, (b) a mixed functions finishing yard and warehouses group (known as he Merchant Mills Loading Yard) which has been perating for a number of years. The areas in ach case are identified as a system while the arious functions, principal product streams nd processing equipment are respectively iden- ified as sub-systems and system elements. etails are given of the models used in each Sub-system dependency on the system as a le is traced by means of an information and ision analysis or by time studies and the sonableness of the system elements is deter- ed by computer programming or by simple com- ison methods. The-accumulated data is used derive improved mill finishing-end or Load Yard,functioning concepts according to pro- rules whilst at the same time considering

Jan 1, 1975

By J Jackson, E Sellers

Blasting related indices were developed to quantify variation in rock strength and structure for each stope, and for each lift of each stope, as part of a Mine to Mill study at an underground open stope mine. The indices were derived from combinations of data from underground diamond drilling because the simplifying assumptions contained in the block model prevented sufficient differentiation in rock mass characteristics to enable adjustments to the blast design.Application of combinations of blasting related indices enabled the identification of stopes with a high potential for inconsistent and oversize fragmentation, underbreak and overbreak. The indices also fragmentation outcomes to deliver increased material flow within stopes, better digability and predict indicative mill throughput. The stopes with issuesCalibration of the results enabled adjustments to the blast design based on the rock mass conditions and accordingly improved the blast outcomes. This enabled improved productivity by reducing underbreak and overbreak, having a more appropriate fragmentation, which reduces unplanned rock handling and improves bogging. The reduction in recovery drilling creates huge opportunities to improve output by reducing production delays and decreasing the overall cost per tonne. By understanding the explosive performance and blast energy distribution in relation to rock mass blastability poor, performing designs in blind upholes and convex stopes were identified.The conclusion of the work is that value improvement, regarding increased revenue and reduced costs, can be achieved across the whole underground Mine to Mill process chain by developing stope based indices from the existing geological information to correctly tailor the blast design to the rock within, and surrounding, the stope.CITATION:Jackson, J and Sellers, E, 2017. Blasting related indices as the key to underground blasting improvements in a challenging rock mass, in Proceedings 13th AusIMM Underground Operators’ Conference 2017, pp 23–32 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 16, 2017

Rare-earth permanent magnetic roll separators, pioneered by our group a few years ago, have distinctly different operation characteristics compared to prior art electromagnetic separators of various types. Many new applications for dry high-intensity (or better: high-force) magnetic separation have been developed in a short time period. It has also been found that the new generation of separators generally are more efficient with regards to removal of weakly magnetic contaminants in glass and ceramic raw materials with minimum loss of valuable product compared to induced magnetic roll (lMR) separators. The latest development is in the area of production of clean magnetic concentrates at high recoveries. It is likely that the PERMROLLR magnetic separator will replace cross-belt and lift-type magnetic separators as a result of this most recent advance.   The paper will review the features of the PERMROLLR magnetic separator in comparison with other types of magnetic separators on the market and give examples on applications.

Jan 1, 1990

By Weber P, Sneyd S

The total world steel production in 1998 amounted to approximately 780 000 000 t. The share of electric steelmaking was in the range of 35 per cent and is expected to increase further to over 40 per cent of the world's production within the next ten years. As electric steelmaking is primarily based on the use of scrap and as it is progressing more and more into higher steel grades the need for low-residual metallics will become increasingly important. Consequently, the demand for scrap substitute material will increase, reflected in the world wide spate of interest for DRI (Direct Reduced Iron) and HBI (Hot Briquetted Iron). The increased significance of DRI/HBI as a substitute for steel scrap has obviously emanated also from its comparatively lower and more predictable costs per ton and definable chemistry. In 1998 already 37 million tons of DRI/HBI were globally produced.

Jan 1, 1999

By B Dodd

This paper details how the Australian Securities and Investments Commission (ASIC), as a disclosure and conduct regulator, approaches regulation of continuous disclosure, capital raising and control transactions in the mining and resources sector, and the reasons for the approach. In examining this topic the paper considers the Joint Ore Reserves Committee (JORC) Code (JORC, 2004), the VALMIN Code (VALMIN Committee, 2005), the relevant ASX Listing Rules and the relevant provisions of the Corporations Act 2001 (Corporations Act). This paper discusses ASICÆs approach to expert reports and disclosure with reference to Regulatory Guides 111 Content of expert reports and 170 Prospective financial information.CITATION:Dodd, B, 2012. Issues in capital raisings and disclosure, in Proceedings International Mine Management 2012, pp 3-14 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 20, 2012

When the Mining Bill came before the Victorian Legislature not so many months ago, the question arose whether mining managers required education, and to what extent. Some members of the House expressed themselves in a way which appeared to leave the impression that mining managers would be all the better if they were not brought up in a scientific school.To try and prove what we owe to science I will give a short history of colonial mining from the earlier period to the present time and compare results.I believe I am right in saying that South Australia is the pioneer colony in mining and to her belongs the credit of not dnly being the first mining colony, but also that her beginning turned out so successful, as the history of the Burra Burra copper mine will testify. At about the same time a little galena mining was carried on nearer to Adelaide, but as this did not prove a success and was only worked by tributing parties, little notice was taken of it.

By A G. L Pratt

Change and its relationship with the introduction of new technology is a constant of human history. The mining industry has many examples of this relationship. This record contrasts with its present day struggles to move beyond a public perception of being just ‘dirty, dumb and dangerous’. The drivers for the introduction of new technology are frequently listed as the occupational health and safety of people working in the mines, reductions in direct operating costs, and increases in productivity.This paper discusses the issues that a mining business needs to deal with to implement new technology with the best possible conditions for success. It comments on how the strategic and tactical components of technology planning relate to and interact with change management. The central discussion is directed at the role that people play in the successful implementation of new technology. The introduction of autonomous underground haulage equipment provides a background for the discussion of this topic.The paper uses case study references, equipment supplier information and research findings. The aim is to offer a high-level view of the issues a mine operator needs to consider when approaching the introduction of new technologies for underground mining.CITATION:Pratt, A G L, 2017. Technology change in underground mining – things to consider, in Proceedings 13th AusIMM Underground Operators’ Conference 2017, pp 103–114 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 16, 2017

By D Craw, N Newman

Previously published stream quality data and AMD (acid mine drainage) analyses have been collated into a database (DAME û Database for Assessment of Mine Environments) and additional samples including NMD (neutral mine drainage) have been collected from coal mine drainages on the West Coast. Variations in the chemistry of mine drainage samples can be related to four factors: 1.       regional geology (Brunner Coal Measures or Paparoa Coal Measures) 2.       mine type (open cast or underground) 3.       hydrogeology 4.       local geology   In general mines hosted in Paparoa Coal Measures produce NMD whereas mines hosted in Brunner Coal Measures produce AMD with highly variable chemistry. Differences in coal mine drainage chemistry between mines hosted in Brunner and Paparoa Coal Measure sequences can be measured with acid-base accounting geochemistry. Correlation of ANC (acid neutralising capacity) and MPA (maximum potential acidity) analysis of rocks with mine drainage samples is substantially better than correlation of NAG (net acid generation) analysis with mine drainage chemistry.   It is likely that NAG analysis over estimates acid generation potential of some samples due to release of organic acids that are not released under environmental conditions. In general, differences in mine drainage chemistry between Brunner and Paparoa hosted mines are attributed to the effect depositional environment and diagenesis on coal measure composition. Exceptions to generalisations relating mine drainage to Paparoa or Brunner host rocks are likely where local geological conditions cause increased deposition of pyrite in Paparoa rocks and additional analyses are required to confirm interpretations.   Based on the interpretation of these results a mine drainage chemistry hazard model has been constructed. The hazard model predicts likely variations in mine drainage chemistry based on the four factors listed above. The hazard model has implications for mine related water quality risks. For example, ecotoxicity, human health affects and selection of remediation techniques are all sensitive to mine drainage chemistry.

Jan 1, 2006

By S E. Munro, P D. Munro

The commonly traded base metals concentrates of copper, lead, tin and zinc are sold by miners to custom smelters using contracts whose terms were generally established at the beginning of the 20th century or even earlier. Technical clauses in these concentrates for items such as payable metals and penalty elements do not reflect current realities of extractive metallurgical technologies and hygiene/environmental issues.It is an axiom that the miners and smelters have a symbiotic relationship. While the existing antique and arcane commercial arrangements serve the purpose of transferring money from the buyer to the seller, they are not likely to result in the industry achieving better overall technical and economic outcomes. By examining the cases for copper concentrates and zinc concentrates in particular, it will be shown that the practical application of these antiquated technical clauses does not drive the miners to produce the better quality concentrates that should be desired by the smelters. This is despite development of mineral beneficiation and hydrometallurgical technologies that would allow the miners to make better products.The adage that any extractive metallurgical problem in the smelter is cheaper to solve in the concentrator still generally holds.While nickel concentrates are only touched on lightly in this discussion because sales terms are more opaque than those for the other base metals, it is expected that the same conclusions will apply.CITATION:Munro, P D and Munro, S E, 2015. Base metals concentrate sales contracts – change Pavlov and the dog, in Proceedings MetPlant 2015, pp 46–60 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 7, 2015

Geotechnical conditions in the Lochiel Deposit are somewhat unusual, and thus geotechnical and hydrological investigations have assumed a high priority. The cost of mining the deposit has been shown to be very sensitive to geotechnical design parameters, and it is now seen to be of paramount importance to establish a high level of confidence in the design parameters used for mining cost estimation. Geotechnical investigations in the Lochiel Deposit reached a crossroads in 1985, when there appeared to be several quite different and equally attractive routes to follow to establish a satisfactory level of confidence in geotechnical mine design parameters. Three main options were identified, referred to as the No Further Work Route, the Drill and Trench Route, and the Trial Pit Route. The No Further Work Route was ruled out as being technically unsound and as satisfying none of the Electricity Trust of South Australia's (ETSA's) or the State Government's requirements. The planning process for further geotechnical investigation involved: clearly identifying the current status of work and significant geotechnical and geological factors planning and costing the alternative schemes for improving knowledge assessing the increase in knowledge to be gained from the alternative schemes . choosing the preferred scheme This process resulted in ETSA's

Jan 1, 1986

By A D. Campbell, G R. Power

The objective of the draw strategy in a caving mine is to maximise economic return by minimising waste dilution3 and maximising ore recovery4. The draw strategy must also include suitable controls for air blast and mud rush hazards and is highly constrained until continuous cave propagation has been achieved. This paper details a three-year project at the Ernest Henry Mine (EHM), which used cave flow simulation software to develop a draw strategy that increased the mine value by 32 per cent.Dilution and ore loss can be significant in sublevel cave (SLC) operations and result in poor recovery and considerable economic losses. To minimise dilution and ore loss, cellular automata software was used to simulate cave flow over the mine life. The optimisation project required mining footprints for various cut-off grades to be developed. Draw strategies for each mine footprint were then generated using a range of shut-off grades. Economic assessment of each scenario was then conducted to determine the mine footprint and corresponding draw strategy that generated the highest NPV (net present value). The iterative simulation process was improved by developing automated software functions in the flow modelling software to reduce time taken to generate and assess life-of-mine (LOM) draw strategy scenarios.In addition to improving the NPV of the mine, the optimisation project also enabled a decrease in the mine cut-off grade which increased the ore reserve and extended the mine life. Overall, an iterative process of mine planning, cave simulation, economic evaluation and geotechnical analysis was used to significantly increase the economic return of the SLC whilst ensuring caving risks were controlled to an acceptable level.CITATION:Campbell, A D and Power, G R, 2016. Increasing net present value by a third at an operating sublevel cave mine using draw strategy optimisation, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 167–174 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By D S. Collins, Z Hosseini, I Pinnock, Y Toya

Microseismic monitoring is regularly used in the mining and geotechnical industries to provide detailed information about rock mass response to operational activities. This paper implements a variable 3D velocity model (VM) at a North American hard rock mine with the aim of further improving the accuracy of seismic event locations. A collapsing method is also used to help analyse two individual seismic event clusters at another North American hard rock mine. In the first case study, the location accuracy of events is shown to improve by moving from a conventional single VM to a variable 3D VM that accounts for voids and different geological domains. The modal average for the event location accuracy improved from 14 m to 5 m when the 3D VM was used. Additionally, the single VM failed to locate 26 per cent of the seismic events that were located by the 3D VM. In the second case study, the distribution of seismic events was further enhanced by using a collapsing method that highlighted planar structures. The collapsing method was performed on two large event sequences that occurred in close proximity and identified different seismic event distributions. One aftershock sequence aligned along a plane, suggesting an activated structure, while the other large event sequence had a more 3D distribution of events, suggesting a complex stress redistribution on smaller structures.CITATION:Pinnock, I, Collins, D S, Toya, Y and Hosseini, Z, 2016. Large event sequence analysis and 3D velocity models for seismic event location accuracy, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 879–884 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016