Search Documents

The Boddington Gold Mine orebody is a large tonnage, low grade gold deposit located within the Archaean Saddleback greenstone belt within the south-western region of Western Australia. The orebody consists of laterite caprock (30 per cent) and clays (70 per cent) produced by lateritisation of felsic volcanics and intrusives. The caprock comprises gravel, hardcap and B-zone which have a specific gravity of 1.8, 2.4 and 1.8 respectively. The clay has a specific gravity of 1.5.

Jan 1, 1993

By Matsushita Y, Maeda M, Sano N

The present study was carried out to explore the possible separate recovery of iron and phosphorus (as gas) from BOF slag using graphite crucibles or graphite powders in the presence of a tin bath. The last is consider- ed to enhance the activity of phosphorus in iron reduced from slag or not to absorb the phosphorus vapour readily. When the slag was reduced in a graphite crucible in contact with a tin bath, the phosphorus reduced from the slag was carried away in CO explosively generated by the reduc- tion of iron oxide. When graphite powder was used as the reductant instead, 78% of the phosphorus was removed from slag, only 3% of which was absorb- ed into the tin bath. The rest left the system as gas. Gaseous dephosphorization depends on the area of contact between slag and reductant as cll n.u the amount of the latter. the reduction behaviour was directly observed, using an X ray transmission technique, to conlirm the reaction mechanism.

Jan 1, 1980

By M Stephens, T A. Sutra

Currently, there are several open pit mines with production rates of about 200 000 tpd of ore that are reaching the end of their economic lives. In most cases, the remaining orebody extends to depths greater than 300 m below the pit limit, leaving hundreds of millions of tons of reserves that can only be recovered by means of an underground mining method. One such method used for mass production is block caving. This paper presents a ventilation system for a four-zone block cave mine operation developed on a footprint 1000 m wide and 1200 m long. The system is designed for a mine with a nominal production rate of 120 000 tpd of ore using diesel powered units on the production and reduction levels. It discusses the air quantity requirements for the worst case scenario, which is anticipated to occur five years after the mine has reached its full production capacity. Finally, it summarises the results of computer modelling exercises that were carried out to determine an economic ventilation infrastructure that includes shafts, drifts, main fans, and ventilation control devices.

Jan 1, 2005

By Wright R. J

The Commission called tenders for a four boom hydraulic jumbo, plus basket, on an art- iculated carrier in Sept. 1977. Atlas Copco submitted the successful tender in Jan. 1978 for the supply of a three boom jumbo, plus basket. The Promec TH470 jumbo was commiss- ioned in the 2000 m long Sophia tunnel in Nov. 1978. Adequate spare parts were not available during the first three months of operation and the hammers could not be overhauled at the recommended interval. One hammer was removed after drilling 13 600 m due to a crack in the intermediate housing. Tests were conducted with different types of drilling consumables. Both rope and Hi-teed threads were tested and found compar- able. The average penetration rate in the granite was 1.1 m/min. Initially the drillers were not experienced enough to operate the BUT 15ERH booms without causing damage to the booms and hoses. Drilling deviation espec- ially of the perimeter holes was greater than expected. It is now obvious that greater attention must be given to attracting, train- ing and retaining the right type of operator and maintenance fitter.

Jan 1, 1981

By Beer G

The recent re-emergence of an Integral Pressure Stripping system which operates with both cell and column in closed circuit at elevated temperature and pressure, requires no cyanide in the eluate solution and has greatly reduced carbon reactivation requirements in seen as a progressive step in this area. Several of these re-configured IPS systems have been placed in service in Australia and overseas in the last three years, with the first of the new generation units constructed and commissioned by Como Engineers Pty. Ltd. at Mt. Fisher in the East Murchison of W.A. in September 1987. This plant was relocated to a new ore body at Darlot W.A. in February 1989. Use is made of a data base of raw plant performance figures from both Mr. Fisher and Darlot and its performance compared with other operating plants. Initial commissioning difficulties of the Mt. Fisher prototype and dis- cussed together with the modifications and operational procedures required to overcome these problems. Stripping times of less than 6 hours at 145 degrees have been achieved with barren carbon values less than l O ppm from loaded carbon values above 3000 ppm and with cell pass efficiencies reaching 90 per cent.

Jan 1, 1991

By Riley S. J

The basic aim of mine planning is to design mine layouts and schedules that achieve optimisation of operations, minimum cost and maximum resource recovery. Successful accomplishment of this aim is facilitated by timely and comprehensive rehabilitation planning commencing at the pre-feasibility stage and continuing until the end of mining. Incorporation of a final landfomt design for waste rock dumps in a mine plan requires a prediction of surface stability, which may be achieved through erosion modelling. Erosion prediction models can be placed in two broad categories: soil loss prediction models eg USLE and CREAMS, and geomorphic models such as SIBERIA. A waste rock dump landform design based on selected slope form and grade and drainage systems should be developed as part of planning. A digital terrain model (DTM) of the landfonn should then be produced which can be modelled for long-term erosional stability using pre-determined parameter values. If acceptable standards of stability are not achieved, the landform should be redesigned and remodelled until the desired result is obtained. The planning process incorporating models requires knowledge of spoil or waste rock properties and model parameter values. This information is site specific and can be obtained from drill cores or costeans at the pre-mining stage and from spoil or waste rock during the mining stage. Realistic model parameter values are critical in post-mining landfonn design and can be obtained by several methods, including rainfall simulation, monitoring, geochemical analyses and grain size analysis.

Jan 1, 1994

Australia, with its fast-growing economy and high standard of a~ living, has a high and rapidly increasing per capita consumption of energyIn total terms, Australia's energy requirements are doubling every 15 years, and among mature Western economies Australia ranks behind only Italy-and Japan in the rate of increase of energy consumption.The use of energy is often accepted as a yardstick of development and on this basis Australia might well congratulate itself on its high energy consumption. However, it is less well recognised that the resources absorbed in the production of energy represent a real cost to the* community, and that just as we strive for industrial efficiency or farm productivity we should strive for economy in the use of energy fuels.Australians spend annually an estimated ú500 million.on all forms of energy, a sum which represents about seven per cent of the Gross National Product. In all, energy production and distribution absorb the employment of more than 100,000 persons. In addition, the annual capital investment by.the oil industry amounts to some E55 millions, by the coal industry about ú12 millions, and by electrical and gas authorities some E108 millions, in total representing more than ten per cent of annual investment in other than private motor cars and housing,

Jan 1, 1962

By Doig ID, Phillips HR

As a prelude to studying the sorption desorption and permeability behaviour of coal cores in a triaxial stressing rig using sorb- able gases, the air permeability of typical cores was measured. Lump coal samples were obtained from three gas-troubled collieries in Queensland and New South Wales. These were cored in the laboratory and a simple laboratory permeameter employed which accepted 38 x 40 mm cores in a thick rubber sheath. Air pressure of 500 kPa was applied outside the sheath to provide suitable sealing between the rubber and the coal. Differential driving pressures up to 100 kPa were employed and the air flow measured by displacement of water columns in inverted graduated cylinders. Flow measurements accurate to + 2% could thereby be achieved. Coal lumps were cored both parallel and perpen- dicular to the bedding plane, and were observed prior to measurement for any notable features, in particular for the presence of fissures. Between samples an overall variation of from 100 milliDarcy was found in Appin, Westcliff and Leichhardt coals. Significant variation was observed both from section to section of a core and between regions of a

Jan 1, 1982

About 20 percent of world gold production has been contributed by gold deposits in Archaean greenstone belts, of which ca 2100 tonnes of gold has been produced from Archaean greenstone belts in Western Australia (Phillips, in press). These deposits are, therefore, important exploration targets and an under-standing of their nature and genesis can help to formulate exploration strategies and delineate potential targets.A literature survey of Archaean granitoid-greenstone terrains indicates that a wide variety of lithologies host gold deposits. The major part of production from the Yilgarn Block, Western Australia, has come from mafic volcanics andintrusives (70% of production),with significant contributions from BIF-hosted ores (15%) and low production from sediments, felsic volcanics, porphyry intrusives and granitoids (Groves et al., in press). Similarly, most

Jan 1, 1984

By Martin T

High methane content of the medium volatile metallurgical coal mined from the Coal Basin mines causes very difficult mining conditions. Rapid desorption into the mine ventilation system limits coal production, requires huge fresh air quantities and creates mine safety problems. In workings deeper than 2000 ft (600m) gassy coal and heavy cover create outbursting conditions. Cross-measure methane drainage has reduced ventilation requirements on advancing faces, but degasifica- tion of virgin coal is needed to improve mining Conditions.

Jan 1, 1982

By Pitkajarvi J

Waste rock dilution causes mill feed grade to be lower than mineral resource grade. In nickel mines relative grade decrease (dilution) may be tens of per cent because of irregular ore boundaries and weak wall rocks. Five per cent dilution costs millions of dollars annually in medium size underground mine. In Outokumpu Group selective bench and fill stoping, cable bolting/shotcrete-skin support and fast ore boundary definition (OMS-logg in-hole logging or sludge sampling) are the key tools in dilution control. Commitment of the whole organisation to keep dilution low is also needed. Dilution sources and effects are discussed with examples of the dilution control methods applied in Outokumpu mines.

Jan 1, 1996

The efficient design of carbon-in-pulp (C.I.P.) plants involves the integration of both process engineering and design engineering.Many recently constructed plants have not recognised the above interrelationship, and as such have incurred higher capital and operating costs than were in reality necessary. This has been compounded in some cases by slavishly following the design of plants where process conditions are different for the ore characteristics in question, thus perpetuating design errors that finally become industry "accepted practice".In the paper that is to be presented the unit operations of crushing, grinding, classification, leaching, adsorption, desorption and electrowinning in C.I.P. plants will be discussed with reference to the integration of process and design engineering.

Jan 1, 1986

By Palmer C. G, Rowe P. G

Ore handling improvements at Mount Isa Mines Limited were necessary to keep abreast of technological advances in all phases of sublevel stoping practice.In the early 1930s an efficient ore handling system was in operation.However in 1936 excessive water encountered in deepening the hoisting shaft necessitated the sinking of a second hoisting shaft. Financial difficulties prevented abandoning the original shaft and surface ore handling and crushing facilities, so ore was transferred underground and underground crushing deferred. It was not until 1951 Jhat multilevel crushing permitted increased efficiency in the handling of ore from stopes. Ore was then hoisted in one shaft and transferred on the surface by conveyor belt to a new crushing plant.In 1956 a planned production increase from 5,000 to 11,000 tons per mining day made possible further improvements in ore handling. Larger equipment was installed and existing equipment modified to capacitate the handling of larger sized ore at increased daily tonnages.INTRODUCTIONThe intensive exploratory programme commenced in 1954 disclosed large reserves of both lead and copper ores and in 1956 an expansion programme was initiated to increase production from 5,000 to 11,000 tons per mining day. The increased tonnage would result in decreased costs per ton and further cost reductions would result from increased mechanisation underground. The combined effect would permit larger tonnages of lower grade ores to be included in ore reserves. To achieve both cost reduction and the scheduled production increase, improvement in ore handling was of vital importance.For efficient and low cost sublevel stoping it is necessary to maintain an economic balance between...

Jan 1, 1961

By G Forbes, D J. Bradshaw, G S. Heinrich, D

Traditionally, operators on mineral flotation plants have relied on visual inspection of the froth surface when making adjustments to process set-points. Machine vision systems are being developed to relate froth surface descriptors, which can be consistently measured in real time, to flotation performance. By investigating the impact of various selected operating variables on both froth surface characteristics and metallurgical performance it is possible to develop a management strategy for the control and optimisation of the process. This paper presents the results of testwork conducted at Kennecott copper mine which investigates the relationship between the froth colour and the concentrate grade and discusses the factors which affect the froth colour. This work shows that the main factors that influence the froth colour in this system are molybdenum, copper and iron concentrate grade, pulp and concentrate per cent solids and pulp iron grade.It goes on to develop models to predict the concentrate grade based on colour information and velocity and stability information. It also shows that the most accurate prediction is made with combined colour and stability information.

Jan 1, 2005

A review of the factors controlling stope wall behaviour such as excavation geometry, rockmass strength, induced stress, ground support, blast damage and drill drive layout is undertaken. In addition, the advantages and disadvantages of single lift stope geometries linked to vertical crater retreat are also analysed. Finally, key components of multiple lift stoping such as cut-off slots, production rings, stope undercuts and drawpoints are studied in detail.

Jan 1, 2000

The paper provides an overview of the development and content of APCOM symposia since their inception in 1961. This development is set within the context of the academic environment in which much of the research published at APCOM symposia is conducted. This environment includes rigorous external assessment of research quality at national levels and against international benchmarks, which carries significant consequences for funding and for the continued existence of the academic minerals industry disciplines. Adverse consequences that undermine the academic provision of mining and resource engineering will impact negatively on the minerals industry by reducing the level of research and education resources available to it.The traditional reductionist approach to research is contrasted with the inter-disciplinary approach that is required to address the complex systems problems that the minerals industry will have to address to ensure its technical, economical and environmental sustainability. Such an approach offers a means of raising research profiles, of establishing mutually beneficial academic-industry engagement and provides an opportunity for APCOM to take a lead role in identifying the research and development agenda for the future

Sep 26, 2011

By Sauer P

The paper deals with the method of operat- ion, types of construction and sizing of screening machines as well as the selection of suitable screen decks. The application of novel screening mac- hines in hard coal preparation plants is explained in detail by way of examples.

Jan 1, 1984

The addition of a thallous salt to the cyanide leach of a calcined pyritic concentrate causes a marked increase in the"rate of extraction of gold. This probably is due to the activation of passive gold by.th,e. thallous ions'.''Lea'd, bismuth, and mercury salts, which should produce ' a, similai effect, fail to do so. It is postulated that'this latter result, together with'the reprecipitation of silver at low cyanide levels, is due to the presence of soluble sulphide. The use of thallous salts to reduce leaching time is discussed briefly.

Jan 1, 1964

By Robins R. G

The dissolution of metallic copper powder in aqueous solutions of cupric sulphate under the influence of ethylene gas was investigated. The dissolution reaction stoichiometry obtained was: Cue+(aq) + Cu(s) + 2C2H4(g) = 2(CuC2H4)+(aq) The rate of formation of the copper (I)-ethylene complex in the above reaction was studied in a laboratory autoclave and the effect pH, temperature, ethylene partial pressure and initial concentration on the dissolution rate was measured experimentally and expressed theoretically in terms of several simple conceptual kinetic models. The results led to the selection of optimum conditions for the reaction and the suggestion of an "ion-molecule reaction" mechanism to explain the very low activation energies for the reaction system. The area of application of this reaction lies in the direction of refining impure copper such as cement copper. Several experiments were performed in which an acidified solution of cupric sulphate under ethylene pressure was used to dissolve copper from the cement copper powder in the form of the copper (I)-ethylene complex, followed by the release of gas pressure to disproportionate the complex and precipitate a purer metallic copper.

Jan 1, 1987

The need to schedule ore production to make maximum use of the strength gained by cem- ented fill during curing is discussed, to show how cement content and hence fill cost can be kept down for any particular operation. Results from laboratory testwork on Isa Mine fill conducted by the author while employed by Mount Isa Mines Limited form the basis of the Discussion

Jan 1, 1973