Search Documents

By M Dorricott

This paper describes the design, construction and performance of sill pillars using cemented development mullock at the Crusader Gold Mine. The orebody is some 35 m - 60 m in length, 5 m - 8 m wide, dipping at 60¦ - 85¦ and plunging at about 40¦ to the north. It is accessed via a footwall decline. The ore occurs at the contact between basalt and ultramafic. This contact is characterised by shearing and alteration; and is prone to unraveling failure. The cut and fill mining method at Crusader extracts 25 m high ore blocks in four flat back lifts and one 8 m thick crown pillar. To enable full recovery of these high-grade crown pillars with minimal dilution, a 5 m thick sill pillar is constructed using cemented rock fill (CRF), after mining of the bottom two lifts in each block. Uncemented development mullock is used as rock fill (RF) for subsequent lifts. Development mullock and cement/water slurry is mixed underground to produce CRF. The fill is transported to the stope in LHDs and dumped on the floor. The sill pillar is advanced progressively, with compaction provided by the loader driving over the previously placed fill. Old jumbo rods are installed as shear pins along the flat dipping hangingwall to reduce the risk of rotational failure of the pillar. A fan of cable bolts is installed into the hangingwall to prevent unraveling failure in the sheared ground. Buffer blasting is used to minimise damage to the CRF sill pillar when the crown pillar below is extracted. At the time of writing, extraction of the crown pillar underneath the CRF has taken place at the 930 stope. The crown pillar was extracted successfully with dilution from the backfill and hangingwall minimised and 98 per cent of the gold recovered. This compares with pillars that were mined beneath uncemented backfill where only 70 per cent of the gold was recovered and where there was significant dilution from the backfill and from hangingwall failures. Where no CRF was placed, there were also numerous production delays caused by large rocks from the hangingwall blocking the stope brow.

Jan 1, 2002

By Zenari L, Kent D

As our mines introduce more sophisticated production technology into their operations, the dependence on communication systems is markedly increased to allow the management of the technology. However the attention given to the communication systems has lagged that given the production equipment - namely LHDs, trucks and jumbos. At times it was treated as after thought. However, this is changing as the degree of automation increases in our mines. The communication system is now being given much more priority and is genuinely becoming a part of the mine design. The transfer of information around underground, as well as between the surface and underground, is an essential day-to-day activity, with the aim being a smoothly run operation. However the mine environment is far from static, and situations arise - such as breakdowns or other incidents - that require swift analysis of the issue, its cause and its remedy. Also, as communication systems become more sophisticated their use in areas, other than direct data flow, become available. The importance of communication, its development, and new areas being impacted by communication is the subject of this Paper.

Jan 1, 1997

McLeod: Without getting into the argument as to how well we can know our resource levels specifically in the immediate short term, I would like to make one or two points about the future, and perhaps try and persuade people that they are not really facing a doomsday. It is fair to say that over the last few years the rate at which we have increased our resources has far exceeded the rate at which we have used them, and this is likely to continue for quite a few years yet. As people are now looking for a substitute for petroleum, later on we will be looking for a substitute for coal, should the position get serious. After all man is pretty versatile, has plenty of initiative-and makes allowances for experience. It has been demonstrated here by the way people are looking at use of low quality coals and better use of the coals that are available. It would be fair to say that what now we regard as economically submarginal deposits will, by the time we need them, become economic. I think that there is quite a lot in front of us in exploration and finding new reserves. I would like to have comment from yourself sir, because I recall reading a report of a meeting, here in Wollongong I think it was, in which you addressed the local branch on the future of coal in Australia, and you said that the coal basins of Australia had been well explored and there was not much chance of new discoveries. Since that time we have seen some thousands of millions of tonnes turned up in the Galilee Basin of Queensland, we have seen five hundred million tonnes turned up in Lake Phillipson in South Australia. Do your previous comments still apply? I would like to hear from some of the exploration people, who are operating on an Australia-wide basis, as to how they regard our chances of discovering significant new deposits and significant extensions of known deposits. H,artnell: Mr. McLeod has asked me to comment on what he has just said. I think that the important thing is that our knowledge of the main coal basins in Eastern Australia is increasing in detail but for the most part the extent of coal basins is not being increased in respect of their superficial areas. There are additions but they are not substantially changing our expectation of what the main coal basins will be. I believe that our task is essentially to intensify our knowledge of the main coal basins that we know about. This is important for example for the various reasons that Mr. Roach was talking about, that is the problem of surface alienation, jeopardising the chance of recovery when you go to underground operations. My approach to this whole problem is predicated on the belief that coal has a special destiny to perform in the next fifty years. I believe that it is going to take up to fifty years and maybe a little longer before the enormously demanding technology for nuclear power recovery is in fact achieved. When it is achieved the supply of energy to the world will be enormous, much beyond what we have ever even dreamed about. The mind boggles at what the people of the middle of next century, of two thousand and fifty, will command in the way of physical resources. It is going to be, I believe, tremendous, but the technology involved is very demanding. I mentioned to Mr. McLeod the other day that according to the information that I got in November last, 60% of the nuclear power stations in the United States were out of action, by automatic cut offs because of safety requirements. The technology of breeder reactors seems each year to be a bit further off. In the meantime coal I am sure is going to be called on to supply power directly to fluidised bed and other technologies for power generation. It is going to be called upon in the near future, I believe, to supply liquid fuel on a vast scale and the only thing in my view that we should be thinking about is whether the coal producing countries of the world will succeed in producing as much coal as is going to be demanded. I believe the real challenge to the coal mining industries of the world is that they may fail to do what is going to be demanded of them. This is a challenge I believe to mining technology. I think that we should be working deliberately and energetically finding ways and means where underground recoveries, instead of averaging 50%, can average 50% plus, plus, plus, and this is the first requirement. We should be spending many millions every year, here and overseas, on increasing our means of winning coal because every tonne of coal that is alienated and left irrecoverable in the earth is going to weaken the capacity of the coal mining industry to fulfil, what I believe to be its destiny in the next 50 years.

Jan 1, 1975

By Leigh J. H

A history is given of the dust control techniques developed and applied by the mining companies at Broken Hill. A history of the regeneration works undertaken since 1936 is out- lined. Particular emphasis is placed on the stabilization of mine residue dumps which are located throughout a belt of mining leases in the middle of the city and which began in 1937. The establishment of vegetation for dust control techniques is discussed in detail and a case study is given of the successful revegetation of the sides of a 650 metre long, 350 metre wide and 35 metre high residue dump.

Jan 1, 1976

Future depth and production limitations of an ore hoisting system are fixed by its initial design criteria. There is little scope to extend these limitations once installation is completed. Depth and production rate upgrades from the initial duty to the hoistÆs practical limitations require capital expenditure in stages, each of which can be defined when assessing the initial system design criteria. A means of presenting and assessing the design criteria, the limiting factors in each option and the relative present and future capital costs is necessary to arrive at a solution that delivers the best value to the mine. Application of this technique to recent friction winder installations and upgrades in the Australian mining industry is of particular interest; however, the analysis methods are also applicable to drum hoists. It is usual to specify a minimum hoisting capacity and depth, based on mine ore handling design and production needs. The final hoist depth and production rate are usually a result of the initial hoist design and hence it is useful from the outset to specify a required production versus depth envelope for the mine. Technical solutions can then be modelled within this envelope at their initial and final duties and a comparative analysis made against the cost of installing and progressively upgrading each solution. Understanding the factors that constrain each solution to a maximum production rate at a given depth is important, as the costs of overcoming limiting parameters such as rope tread pressure and motor power can be significant. The task of understanding and evaluating the options open to the hoisting system designer is simplified using this approach. Communicating the results of a multi-dimensional problem such as hoist specification is also made easier using the graphical methods inherent in the analysis.

Jan 1, 2005

By Shuqing L

The application of single liquid cement for fracture grouting in base rock may have history more than 120 years. The disadvantage of it is difficult to increase the grouting efficiency, because the jelling time of it is very long and hard to control. The double liquid grout, such as chemical grouts and cement water glass grout was developed at the end of 1960.'s Although the jelling time of this kind of grout can be controlled, it mast adopt double liquid grouting technology, use complicated equipment and is not easy to control component's ratio of the grout. Another disadvantage for chemical grout is high price, and have pollution to environment. OCE series single liquid grout is the effective grout material developed recently by making large efforts in Ohina. Main feature of it is that the jelling time is easy to control, materials from cement and clay are very cheap and without pollution to environment, and the grout can be injected by single liquid technology. The effect of QCE series grout has been proven by its application in China. It can be believed that QCE grout has great economic efficiency and will give a push to develop grout material.

Jan 1, 1988

The application of single liquid cement for fracture grouting in base rock may have history more than 120 years. The disadvantage of it is difficult to increase the grouting efficiency, because the jelling time of it is very long and hard to control. The double liquid grout, such as chemical grouts and cement water glass grout was developed at the end of 1960.'s Although the jelling time of this kind of grout can be controlled, it mast adopt double liquid grouting technology, use complicated equipment and is not easy to control component's ratio of the grout. Another disadvantage for chemical grout is high price, and have pollution to environment. OCE series single liquid grout is the effective grout material developed recently by making large efforts in Ohina. Main feature of it is that the jelling time is easy to control, materials from cement and clay are very cheap and without pollution to environment, and the grout can be injected by single liquid technology. The effect of QCE series grout has been proven by its application in China. It can be believed that QCE grout has great economic efficiency and will give a push to develop grout material.

Jan 1, 1988

More than in any other way, the community judges the minerals industry by its environmental performance. Minerals Council of Australia web site www.minerals.org.au/media/code Time is overtaking us. What was good enough yesterday is not good enough today. What may be acceptable today wonÆt be tomorrow. So we need to leap forward. We need to begin to move towards sustainability. Dick Zandee, Managing Director, Placer Dome Asia Pacific The competition for access to exploration and mining opportunities is intense. So is competition for the best people, capital and community support. Poor environmental performance damages a companyÆs ability to attract these. Quite simply, good environmental management is good business. Hugh M Morgan AO,Chief Executive Officer,WMC Limited. Decisions made by private industry and international corporations are increasingly determining the fate of the environment. ...Nothing could be more shortsighted than for todayÆs conservationists to neglect cooperation with business and industry as a means of moving company philosophy and public accountability ahead in favour of the environment. Dr Claude Martin,Director General,WWF International The four quotes above well illustrate the challenges faced by companies and conservationists in attempting to achieve the societal goal of sustainable development. That this aspirational goal itself is far from clearly defined, although it has been widely accepted and endorsed by governments, business and civil society, exacerbates the challenges. Sustainable development has as its central thesis the integration of environmental, social and economic policy. Its attainment by business has been described John Elkington (1998) as the pursuit of the ætriple bottom lineÆ - the achievement of social and environmental targets, in addition to the traditional economic bottom line. It is self-evident that business is both competent and comfortable defining and measuring economic performance and reporting that performance to internal and external audiences. As long as information has been prepared according to the established standards of measurement and reporting of economic performance, all audiences can have confidence in its accuracy. Business does not enjoy the same competence and comfort with regard to social and environmental performance. This is no startling condemnation of business, any more than it is a criticism of governments, non-government organisations (NGOs) or academia. It is a statement of fact that the tools to allow for credible definition and reporting against the other two components of the ætriple bottom lineÆ have yet to be fully developed and are, therefore, far from being widely accepted. Crucial to achieving sustainability is the ability to measure progress toward the goal. The task is to develop means to define appropriate performance standards and to credibly measure and report company environmental and social performance against those standards.

Jan 1, 2000

WHEN reading reports on reefs and lodes, one often comes across the statements "short shoot," "narrow shoot," "wide shoot," & c.From a number of reports in the writer's possession, some by members of the Geological survey, it is plain that the words "short," "narrow," "wide," "long;" &c., are used somewhat carelessly.In one official report on a certain field, for instance, the reefs are described as having "short, rich shoots"; another report on the same field states that "the reefs were characterized by narrow shoots, rich at the surface." Again, Charters Towers is described as having "wide shoots"; another writer says they are "long shoots. "The writer has read again of "short shoots which went down like pipes," and of "narrow shoots of limited extent." No doubt one can make out what is really meant, but the language is mixed. It is apparent that "narrow" is meaning the same as "short," and that the shoot has not much length in a horizontal direction. Nothing is said about the thickness or width of 'said shoot, or its depth. The "wide" shoot is evidently a "long" one; its thickness 01' width and depth is not specified. When we consider these terms, it is seen that only a few words are needed, and that these few should (as they do) have a definite meaning. In the course of his mining experience, the writer has seen shoots of almost all sizes, and some have been very long (in horizontal measurement), and have been followed down for great depths, these shoots being the best type-Charters Towers, Walhalla, &c., are examples.

Jan 1, 1909

Geotechnical practice combines the site engineering geological model with engineering design and operations to control risk. The responsibility of the geotechnical professional is to present relevant engineering geological information to an engineer to effectively impact an outcome. Return is enhanced by understanding expected operating and capital cost due to ground conditions.   Risk is effectively communicated by a successful geotechnical practitioner. In a mining environment the need is to assess ground conditions accurately and quickly, and to effectively communicate expected ground response due to mining. A good engineering geological model includes a description of geotechnical engineering parameters to design assuming reasonable expected soil, rock and water conditions. Pit slopes are steepened, stope spans widened and waste foundations and land forms are constructed all under geotechnical control.   The responsibility of the geotechnical professional is to collect, assess and disseminate relative engineering geological information. The geotechnical professional is a person advising on ground related engineering, and generally operates within geology and engineering end members.   Return is better assessed on an understanding of ground cost. In operations the goal is to meet production at lower cost. In evaluation, regional and exploration geology, mine design and expected operational factors influence expected cost and project return. Return allows companies to meet shareholder expectations, attract equity to develop and add value to the community.   This paper presents a discussion with some examples to present an approach and design philosophy for geotechnical practice in the mining industry.

Jan 1, 2004

By Bowmaker MD

Zinc and lead sulphide flotation con centrates containing from 0.02 to 0.20% Cd are roasted on an updraught sinter machine at the Cockle Creek Works of Sulphide Corp- oration Pty. Limited to provide sinter for simultaneous smelting of zinc and lead in an Imperial Smelting Furnace (I.S.F.). The major portion (about 85%) of cad- mium in concentrate feed to the Sinter Plant is eliminated with sinter fume and is rec- overed by weak acid leaching in the Cadmium Plant'followed by counter-current decantat- ion, ion exchange concentration, precipitat- ion of cadmium sponge and partial refining to caustic refined cadmium metal. Cadmium not eliminated during sintering is volatilised in the I.S.F. and subsequently recovered as zinc alloy by distillation in the zinc ref- ining columns of the Zinc Refluxer. The partially refined cadmium metal and cadmium- zinc alloy are blended as feed to the cadm- ium refining column where separation and recovery of cadmium is effected. Condensate from the column is further refined under caustic soda flux and cast into anode shapes. Production is 200 t.p.a. at 85% recovery of cadmium in concentrates. Emphasis is placed on changes from the practice described by Baker and Munro (1965) and upon operation

Jan 1, 1972

By W Gale

Rock and coal fractures together with micro seismic vibration is a common occurrence during mining, however, it is very uncommon for coal and rock to be propelled into the roadway. Irrespective, such occurrences do occur and appear to require significantly more energy than is available from strain energy release during coal cutting. The sources of energy which can contribute to the propulsion of coal from the face or ribs are typically strain energy from the surrounding ground, seismic energy from a rapid rupture of the ground in the vicinity, or rapid expansion of gas from within the burst source area. The aim of this presentation is to briefly review the mechanics of a coal burst and to discuss the mining situations for which the energy is sufficient to create bursts. A brief discussion of alleviation strategies is discussed. This is an abstract only. No full paper was prepared for this presentation. CITATION:Gale, W, 2018. An overview of coal burst phenomena, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), p 2 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

The phrase "Total-Energy" has, during the past few years, become widely used to describe a wide range of very different operations. However, if accurately described they all have one basic factor in common - energy usage is optimised with the prime mover being powered by gas or oil to generate shaft horsepower and the products of combustion being put to some use. The item which distinguishes a Total Energy system from any other engine or turbine driven project is that orate pains are taken to utilize the waste heat, whether this be in the form of exhaust gases and/or engine jacket ling water. n areas where grid supplies of electricity are readily available, the economics of most projects undoubtedly hinge upon the successful application of waste heat. However, there has been a growing awareness of other benefits, such as reliability of supply, which can be incorporated into the system. In particular these factors sway managements of hospitals and companies with complex computer facilities to examine closely the feasibility of Total Energy, Consequently, in America for example, where many systems have proved themselves the list of applications is wide - shopping centres, apartment blocks, office buildings, airline terminals, universities, schools, motels. And these do not cover the industrial sectors where the range is wider. The total number in North America is now approximately 500 and this to some extent-speaks for itself. In Australia, the real work involved in carrying out feasibility studies for Total Energy is only just beginning. 'in some quarters, the concept is not well received in that it is too new. Therefore, a typical approach is to play safe and wait until some other company has proved its operation "under Australian conditions". This is certainly a realistic approach when considering something revolutionary but as far as Total Energy.is"concerned all the individual components and sometimes combinations, (engines, generators, boilers, air-conditioning units) have been in operation for many years. The only innovation is that they are now all being brought together under one roof. This should not be forgotten when the question "where can I see something like this operating?" is asked.

Jan 1, 1970

The issue of flyrock is critical to the operation of all mineral extraction sites that use blasting. This paper takes a risk-based approach to identifying, analysing and managing the flyrock hazard. The basic cause of flyrock generation is a mismatch between the energy available and the work to be done. It should be noted that the energy available depends on the charge confinement. This mismatch can be caused by an abrupt decrease in rock resistance (geological weaknesses), overcharging, inadequate delays between holes and rows, inappropriate blast design and inaccurate drilling. The mismatch can come about from two sides; either too much energy (charge) for a fixed burden (work to be done), or insufficient burden (work to be done) for a fixed charge. The main mechanisms of flyrock generation are rifling, cratering, face bursting and secondary blasting. Each source mechanism has different characteristics in terms of vulnerable locations and each requires different control measures. However, all controls require a high level of quality control and assurance. A range of different approaches for managing flyrock risk and determining blast clearance zone dimensions are presented. A prescriptive consequence-based approach is discussed. A conventional risk matrix based approach is outlined with some innovation regarding controls rating and uncertainty ratings. A published semi-empirical approach is discussed. Two examples of quantitative flyrock risk analysis are presented; one involves bench blasting based on a published paper and the second is a cratering example developed by the author based on consulting projects. Finally, a stochastic approach based on published work is presented which simulates cratering superimposed on face bursting mechanisms. Also, a stochastic analysis undertaken by the author of the cratering example is presented. Effective blast emission management is required for two reasons; firstly to reduce and/or eliminate safety risks and secondly to manage public perception of blasting risks such as flyrock. The conclusion of the current research is that the wild flyrock risk can be estimated using existing techniques. Furthermore, both qualitative and quantitative risk management methods as discussed in this paper can be used for flyrock management for a given blasting situation. A combination of both is considered to be best practice.

Jan 1, 2007

By Hyde L. J

Blasting is one of the available technologies to be employed in underground excavation systems. In many instances it can be the only technology which is suitable. The recent moves towards more mechanised working systems is resulting in a reduced awareness of new blasting practices and technologies on the part of many excavation engineers. Recent developments in blasting systems can be utilised to significantly improve operating efficiency, reduce total cycle times, better comply with regional environmental constraints and reduce the total cost of underground excavation. Blasting is and will remain, a very adaptable and exciting alternative which is far from boring.

Jan 1, 1987

The attachment of a spherical particle to a bubble is theoretically investigated under the condition of a mixed sorption coating of a collector. It is shown that the attachment is determined primarily by the hydrodynamic factor involving the displacement of liquid from the gap between a bubble and a particle. The dependence of the attachment on the state of the surface of particle (sorption coating) is due to a change in the boundary conditions on the interface with water both in the case of surfactant chemical sorption and in that of the physical adsorption of oil. It is demonstrated that at large distances the thinning of a interlayer is facilitated by a physically sorbed collector, while near the bubble this is done by a chemically sorbed one.

Jan 1, 1993

By A G. Thompson, E Villaescusa, D Howard

The Western Australian School of Mines (WASM) has developed a facility for the static testing of full-scale ground support elements (Morton et al, 2007). The test facility consists of several stiff steel frames used to support the sample and a screw feed jack is used to load the sample. A large-scale punch test method has been developed to load various shotcrete configurations. The shotcrete is sprayed on to a rock substrate containing a centrally located circular disc. The rock and shotcrete sample is placed on to the sample frame and restrained on all sides. The circular disc is displaced at a constant rate by the screw feed jack which in turn loads the sample. Instrumentation measures the displacement and the load being applied to the sample through the loading disc. The testing method is described in detail and the results from the testing program are presented. The results show that it is possible through laboratory testing to simulate some of the mechanisms of shotcrete support reactions better than conventional beam and panel tests.

Jan 1, 2008

By T Jones, K Karunaratna

The Kalgoorlie Consolidated Gold Mines (KCGM) Fimiston Open Pit is located on the eastern boundary of the Kalgoorlie-Boulder City and is mining an area traditionally known as the Golden Mile. The pit area has been continuously worked since 1893, predominantly by underground mining methods and more recently through open cut mining. There are over 2000 km of old mine headings and numerous stopes under the open pit area. KCGM has interpreted and digitised the underground mine plans and stope sections into a common database. A 2D-model software package, called Pits, was developed in-house and allows old workings to be displayed at any bench level; this is integrated with 3D Vulcan modelling software, which allows triangulated surfaces to be displayed. Almost every mining activity is affected by underground workings. The effective management of the interaction between current mining and the underground workings is very important for safety and production. A specific ævoidÆ management department has been formed and its broad objective is to minimise the impact of underground workings upon production while maximising safety. Special criteria and procedures have been developed and implemented to keep personnel and machinery from being exposed to unsafe ground. It is of primary importance to accurately define the location and outline of underground workings in advance. Probe drilling has been used as the key tool for that purpose. Various geophysical methods have also been trialled on site to detect underground workings; these are discussed in some detail. This paper discusses ævoidÆ management issues such as data integration, void detection and flagging. The impact of underground workings on mine planing, production and slope stability is also discussed.

Jan 1, 2003

FaulIing west of the Mount Isa mine is described and is shown to be related to three groups of folds that have been recognized in the area. The first period of faulting postdates the first generation folding; these faulIs are regional faults (tectonic discontinuities) which are folded by second generation folds. The faulting accompanying the second generation folding divides the area west of the Mount Isa mine into four structurally and metamorphically identifiable blocks. The most prominent of these second generation faults is the Mount Isa Fault, which is characterized by a number of distinct zones of intense second generation folding and the presence of localized layers of mylonite. Only limited evidence for brittle deformation has been observed and the major movement appears to be associated with the plastic deformation of the rocks. Confined to the areas of second generation folding in the Mount Isa Fault are numerous third generation kink folds. A detailed description of the Mount Isa and other faulIs is presented together with evidence for their existence. The displacement accompanying this faulting cannot be established because of the complexity of the structure.Postdating these faults and all the folding of the area are minor cross faults.

Jan 1, 1973

A useful sampling device can be constructed using three movable flaps. One is moved between its two extreme positions as material is flowing past it; the other two are only moved while no material is flowing past them. Material commences to flow into a sample container as the primary flap is moved from right to left, continues to flow into the sample container as the primary flap is moved from left to right, and the flow is terminated as the primary flap is next moved from right to left. As for several other sampling devices, an argument that there is no delimitation error can be made on the basis that the sampler conceptually divides the stream up into discrete portions and takes a set of equally-spaced portions as a sample.

Jan 1, 2008