Search Documents

By Onal G, Celik MS, Dogan MZ

Chromite tailings assaying 21.2 per cent Cr2O3 was upgraded to 48.7 per cent Cr2O3 at a recovery of 72.0 per cent using column flotation with a mixture of anionic collectors at pH 11. Electrokinetic methods were used to elucidate the mechanism of collector adsorption and correlate the findings with the optimum flotation conditions. Multivalent constituent ions such as Cr3+, A13+, Fe2+ and Mg2+ were found to adsorb on chromite surface and shift the zpc of chromite in the direction of oxide form of the mineral. The anionic collectors also imparted a negative charge to chromite in the entire pH region. The higher zeta potentials obtained upon adding the anionic collectors is ascribed to the adsorption of anionic surfactant onto the positively charged chromite surface. The positive sites are generated through formation of significant amount of hydroxy complexes of magnesium at pH 11. Complementary infrared data reveal the absence of a shift in the spectra indicating the possibility of physical adsorption in the system.

Jan 1, 1993

By E House, V Lisitsin

Recent whole-rock geochemical data from nearly 900 fresh drill core and underground samples taken from seven central Victorian gold deposits confirm the presence of distinct and identifiable primary alteration haloes surrounding the deposits. Ferroan carbonate alteration extends for up to several hundred metres away from turbidite-hosted gold mineralisation outside of contact metamorphic aureoles. A less distinct phyllic alteration zone can be identified using geochemical molar ratios or short wave infrared analysis. It generally overlaps a sulfidic halo characterised by disseminated pyrite and in close proximity to mineralised structures, arsenopyrite. The extent of the sulfidic halo can be traced using low-level analysis of pathfinder elements such as S, Au, As and Sb. Recognition of these alteration features enlarges the target for exploration and provides a tool by which drilling can be directed towards mineralised structures. An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation.

Jan 1, 2008

Studies of the morphology of seamounts within the Hawaiian, Line Islands, Gilbert and Phoenix Seamount groups indicate that the morphology and size distribution of seamounts vary significantly from one seamount group to another. The Line Islands group appears to be the most complicated of all the groups studied thus far. This group is complicated by reactivation of volcanism, which has superimposed volcanics on sedimentary rocks. These seamounts display abundant volcanic features on their summits. Seamounts within the Hawaiian seamount chain display a marked absence of volcanic features due to the . presence of thick carbonate caps. Reef platforms and sealevel benches are very common on these seamounts but are absent from seamounts in most other seamount chains in the central Pacific. Slope angles vary regionally between seamount groups. The minimum slopes are found on Necker Ridge in the central Pacific basin. The maximum slopes are found on ridge-crest seamounts. Roughness increases proportionally with mean slope angle.

Jan 1, 1987

This paper deals with a few aspects of town planning and town management which affect human relationships within that town. Its scope is limited to the consideration of towns forming an adjunct to a mining operation, and particularly considers these aspects at the Hamersley Iron Pty. Limited, town of Parabur doo, Western Australia. Planning and standards of a new town and amenities are-discussed and related through living comfort to an effect on human relation- ships. Town administration and the promotion of many forms of social activities are dealt with in detail to illustrate the importance of quickly forming a cohesive community from a large number of newly arriving individuals. The results achieved by the planning and administration at Paraburdoo are highlighted by involving many residents by way of answers to a questionnaire.

Jan 1, 1973

By Y Peng, D J. Bradshaw, G Long

As copper reserves deepen, they are becoming increasingly less pure. Penalty elements such as arsenic, antimony and bismuth are occurring in increasing concentrations. Environmental issues with smelters are leading to increases in penalty rates for these elements such that some concentrates may become difficult to sell. Arsenic concentration in Rosebery copper concentrates during 2010 varied between 3000 and 8500 ppm. Arsenic levels above 5000 ppm can preclude import to some customer countries. Optical mineralogy has indicated that arsenic in Rosebery copper concentrates is most commonly associated with tennantite (Cu12As4S13) in solid solution with tetrahedrite (Cu12As4S13). In addition, silver reports to concentrate as freibergite (Cu12As4S13 ). A reduction in arsenic content will therefore lead to a concurrent reduction in the silver content.A literature review by Long, Peng and Bradshaw (2012) indicated that arsenic bearing minerals could be removed using potential controlled flotation. Some success in reducing the amount of arsenic had also been reported using either roasting or chemical depression using reagents such as lime and cyanide. Due to the location of the Rosebery concentrator adjacent to world heritage listed temperate rainforest, the use of a roaster or cyanide was immediately discounted. Lime is already used as a reagent in the Rosebery flow sheet, so could be considered as a potential arsenic depressant.In order to determine a method of separating out the high arsenic bearing minerals, two series of flotation tests were conducted. The first series investigated the effect of pulp potential on the recovery of copper, silver and arsenic minerals; a second series investigated the effect of pH, froth depth and regrind.CITATION:Long, G, Peng, Y and Bradshaw, D J, 2012. Production of a low arsenic copper concentrate at MMG Rosebery, in Proceedings 11th AusIMM Mill OperatorsÆ Conference, pp 347-354 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 29, 2012

Improvements in mechanisation should not be considered independently of safety and of environmental hazards. The need to keep gas contents within statutory limits may make the time needed to partially drain a gassy seam the effective control on face development times. Dust levels may provide an effective control on coal extraction rates on any one face. The combination of gas and dust on high output longwall faces may make it necessary for each one to be treated as a separate mine in terms of ventilation, and the faceworkers may need special protection. Mechanisation and safety can be mutually beneficial when mechanisation combined with systematic safety assessment reduces accidents, and when a thorough study of how to reduce accidents and health risks indicates the best method to improve mechanisation.

Jan 1, 1988

By Toffeg A. N, Abdul-Hameed I

More than 1000 Ian of seismic reflection data correlated to ten exploration wells along with geological, gravity and magnetic data are used to construct the subsurface structure, in particular the crystalline basement, along a corridor approximately 100 Ian wide that traverses central Iraq in SE-NW direction for a distance of about 500 km from Baghdad in the central part of Iraq to Dohuk near the Turkish border. This transect is one of few such transects that represents the Iraqi contribution to the Global Geoscience Transects (GGT) project. The transect crosses two out of three major tectonic elements of Iraq: the unfolded zone and the folded zone.

Jan 1, 1990

By Yoshii Y

Many kinds of shield machines are being driven in the soft ground of Tokyo metropolitan area. Tunnel alignments for underground power transmission lines are generally planned to pass under public roads where facilities, especially life-line facilities, are densely located. Therefore, it is frequently required to drive the shield machines along very sharply curving routes. This paper reports on the performance of the new shield machine - the Sharp Curve Excavation Shield Machine - developed by Tokyo Electric Power Co., Inc., which can freely drive along a much sharper curve than conventional machines. Some of features of the developed devices of this machine are, maximum flexing angle of 6.5 degree in all deirection at the middle of shield body, maximum bending angle of 3.5 degree in all direction at the cutter disc, and so on. This shield machine can there- fore drive along curve of minimum radius 15m. The machine was confidently applied to the const- ruction of tunnel in soft clay strata at N values 2 to 5. Outer diameter 3.7m. Length 202m. Horizontal curve; radius 15m, length 20m x 2. Vertical curve; radius 30 m, inclined driven up 29%. The behaviors of the shield machine, segments and surrounding ground were monitored during construction for safety and efficiency check of this machine.

Jan 1, 1987

An algorithm is described which leads directly to a unique set of coal washing parameters which, in two or more parallel streams, will give maximum yield of product at a given ash. This occurs when all parallel streams are washed to the same incremental ash. This strategy is shown to offer a considerable increase in yield compared to the simpler strategy of washing each stream to the same sumulative ash.

Jan 1, 1987

An extensive study was carried out to evaluate the performance of Outokumpu OK50, OK38 and Maxwell MX14 cells at ComincoÆs Red Dog flotation concentrator in Alaska. Tests were conducted by varying operating conditions of the cells installed in different circuits in the plant. The hydrodynamic and gas dispersion properties were measured and the metallurgical performance of the cells was evaluated for each condition used in the tests. This paper highlights the importance of superficial gas velocity, bubble surface area flux, gas hold-up, power consumption, residence time distribution and froth flow behaviour in optimising cell performance. The findings of these tests provide valuable insights into selection of the best cell operating conditions to optimise circuit performance.

Jan 1, 2000

In recent decades the awareness of environmental issues by the general public has developed at an accelerat- ing rate. This is the result of a number of factors including more scientific knowledge of environments and of the impacts of modern society upon them, higher levels of education, the opportunity for people to travel more, and the success of the various communication media in bringing in- formation to the communities of the world about such environmental crises or threats as the smogs of Los Angeles and London, the Torrey Canyon and Santa Barbara oilspills, Minamata disease in Japan, the spread of the Crown of Thorns starfish, the disposal of toxic industrial wastes into the Upper Rhine, the discovery of high mercury and zinc contents in marine foods in southern Australian waters, and the proposal to mine limestone at Precipitous Bluff in Tasmania.

Jan 1, 1975

By C Deacon

It is common practice to include microspheres or similar density reducing agents in inherently insensitive water-based commercial explosives to achieve detonative sensitivity in the absence of chemical sensitisation. It has recently become possible to similarly include microspheres in LDAN (low density ammonium nitrate). Further to previous studies and publications to determine the benefits resulting from the use of microsphere enhanced LDAN technology in blasting, additional advantages are described in this document. These include range tests at independent testing facilities (Universal Tech Corporation û USA) which reflect results observed in the field, and support theoretical assumptions made when the products were introduced. Additionally, on-site studies in opencast pits using Heavy-ANFO blends incorporating modified LDAN, show that monetary savings can be realised through significant advantages gained in plant throughput and explosives use.

Jan 1, 1999

The passage of a vast array of new State and Federal environmental legislation over the last couple of years has required many mine operators to sharpen their focus on environmental requirements. Established requirements, such as environmental impact assessment, minimising disturbance and rehabilitation must now be complemented by mine environmental management plans. These may not only require regular monitoring of mine operations and detailed forward planning to prevent or reduce environmental harm caused during mine operation, but annual updating. It is likely that in future these plans will be required to incorporate general principles such as pollution prevention, sustainable development, waste minimisation and conservation of biodiversity and ecological integrity.

Jan 1, 1993

By Boger D. V

Two industrial case studies in which detailed investigation of the flow behaviour of mineral slurries is used to assess the feasibility of pipeline solid transport are described. The first example deals with the pumping of highly concentrated bauxite tailings to disposal, while the second exam- ple examines the possibility of transporting high-density Victorian brown coal slurries which previously has been thought as uneconomical. It is demonstrated that these typical solid handling problems can be solved by a good understanding of the rheology of suspensions.

Jan 1, 1989

Erosion of unprotected batters, spoil banks, slopes, and stockpiled material creates a multitude of environmental problems. Winds blowing across these denuded surfaces can generate dust clouds capable of depositing un- desirable particulate material a considerable distance from the source. Water eroding these areas continually exposes new surfaces which may be oxidized. Iron pyrites can be dissolved in the flowing water, resulting in the addition of pollutants to streams and water sources. Silting of water sources can also occur as a result of this erosion. Valuable topsoil can be blown or washed away. In addition, the after-effects of erosion leave a visual pollution which is more difficult and expensive to correct than to prevent.

Jan 1, 1976

By Waghorn EP, Gleeson HB

The Loy Yang Optr, Cut is a brown coal mine bring developed in the Latrobe Valley region located some 160 kin south-east of Melbourne, Victoria. The mine has been designed to supply a mine mouth power station at a rate that will rise to 32 million tonnes per year by the mid 1990's. Continuous mining metnuds are employed using bucket Whtel excav- ators and conveyors. This paper describes the basis of the design of the Loy Yang continuous mining system ano cne experience of four years of initial operation.

Jan 1, 1987

By Pollard D. M

The removal of nickel from lead by sulfur drossing was investigated using a technique which models industrial batch decoppering practice. Successful denickeling to 0.005% (Ni)pb was consistently obtained in the absence of silver, well below the experimental equilibrium value of 0.015% but still above levels obtained in industrial practice. Silver appeared to have little effect upon denickeling. The final nickel content was dependent upon the initial nickel content, the total sulfur addition and the stirring time. The presence of nickel was found to give no assistance to successful decoppering. Simul- taneous removal of nickel and copper was observed at silver contents in excess of 0.02%. Extended stirring resulted in a further lowering of the nickel content but reversion of copper to the bullion was observed. Experimental work has shown that nickel can be removed by a standard decoppering operation; a procedure which is used in secondary lead re- fining. Alternatively nickel can be removed during initial decoppering in primary lead re- fining operations.

Jan 1, 1987

In a stipulated hard rock situation, drilling and blasting costs per tonne in open cutting or underground operations are comparable. In open cuts the drilling and blasting costs per tonne of ore are multiplied by the waste ratio.Conventional underground loading and haulage practices are so batch-oriented that the cost per tonne of ore handled is a large integral multiplier of open out costs per tonne loaded and hauled.If underground costs are to be reduced to compare favourably with open out costs then loading and hauling practices underground must be converted to a non-batch continuous system. This can be achieved by utilising gravity to control ore to mobile crushers feeding conveyors running direct to surface.

Jan 1, 1985

The efficiency with which it is expected that a particular coal may be burnt in a power station boiler significantly affects the value of the coal. Consequently many laboratory tests have been developed to provide data on the combustibility of coal. Computer modelling of coal combustion has also provided insight into limits on coal burn- out. Such modelling suggests that burnout of bituminous coal in a power station boiler will be strongly influenced by physical limits on the diffusion of oxygen to the individual coal particles. Coal chemical reactivity appears to be relatively less important. As a consequence of the diffusional limits, significant improvement in burnout is achieved either by producing less large p.f. particles or by providing sufficient furnace residence time to burn the large particles. Field data from a variety of power stations supports these cn.clusions. Burnout was also found to correlate well with volatile content for a number of coals from widely different sources. This is expected as the high vola- tile coals produce less residual char to be burned by the relatively slow heterogeneous Combustion.

Jan 1, 1987

By McCarthy P. L

With production at Olympic Dam scheduled to commence in June 1988, it has been necessary to install a complete underground ore handling system capable of removing two million tonnes of material annually from the mine. The system comprises mucking from stope drawpoints, truck haulage to underground storage, primary crushing, conveying and hoisting. On the surface, material is conveyed to stockpiles at the Metallurgical Plant. Mining of the numerous special excavations within the system was incorporated into the mine's ongoing development program prior to the underground construction phase. Utilisation of a decline from the surface enabled versatile construction equipment to operate at the underground sites as well as simplifying the transportation and delivery of construction Materials.

Jan 1, 1988