Search Documents

By Steve McAlister, Colin Sprake

"Enhanced gravity concentration machines have been applied successfully in the following areas of precious metal recovery flowsheets:1. Primary Grinding Circuits2. Shaking Table Tailings3. Pre-Concentration of Leach Feed4. Flotation Concentrates -•, Flash•, ConventionalAlthough great progress has been made, the ability to produce directly smeltable concentrates still remains elusive. Even without this ability, centrifugal concentrators are finding wideningapplications in precious metal concentration:1) PRIMARY GRINDING CIRCUITSEnhanced gravity concentration technology has largely replaced jigging as the technology of choice in precious metal grinding circuits worldwide. The benefits of using a centrifugal field to concentrate both coarse and fine gold are well documented but the placement of these machines within grinding circuits is still evolving. Conventional wisdom dictates that the best location for enhanced gravity machines is cyclone underflow on account of the elevated grade found in this stream when compared to cyclone feed or overflow. Plant operating experience at both large and small scale indicates that there are compelling arguments to place ENHANCED GRAVITY MACHINES on cyclone feed instead. At least two new plants, presently in the detailed design stage will incorporate gravity circuits that treat mill discharge or cyclone feed, Teck Cominco’s Pogo and Newcrest’s Telfer Expansion.Current Conventional PracticeThe current stream of choice for enhanced gravity concentration within grinding circuits is cyclone underflow although recent information indicates a swing toward cyclone feed. Here are some of the arguments for treating a portion of cyclone underflow:"

Jan 1, 2003

By K. G. Stowe

"1. Introduction Mattagami Lake Mines and Orchan Mines operate zinc copper mines adjacent to one another near Matagami, Quebec, situated approximately 300 kilometres north-east of Rouyn-Noranda. (Note: Mattagami Lake and Orchan are in the process of being absorbed by Noranda Mines and will become Noranda Mines-Matagami Division). Both concentrators began operations in late 1963.The Mattagami Lake concentrator is capable of treating up to 3,500 metric tons per day of massive sulphide ore with a mineral composition shown in TABLE 1. The Orchan concentrator consists of two separate circuits - the Orchan circuit with a capacity of 1,050 metric tons per day and a custom circuit with a capacity of 825 metric tons per day. Throughout its operation, Orchan has custom milled ore from several smaller deposits in the Matagami district."

Jan 1, 1979

By Suman Giri

Non-Intrusive Load Monitoring (NILM) is a method of extracting appliance-level power consumption information from aggregate circuit-level data with the goal of giving users feedback regarding their energy consumption so they can take control of their consumption habits. In this paper, we present a novel algorithm for classification of on and off states of appliances. We compare the performance of our algorithm in on state detection with a pervious paper that evaluated the same dataset and show that it performs up to 13% better. We also present the results of a case study where we collected data for different modes of a cooktop, microwave and dishwasher and used our algorithms to perform power estimation. The error on ten different setups in the test bed ranges from 1% to 32%. We discuss our results and lay out ideas for future work.

Aug 1, 2013

By J. J. Denny

IN November, 1932, an investigation of silicosis was undertaken at the Mcintyre Porcupine mine, Schumacher, Ont., after a discussion of the p"roblem with Sir Frederick Banting and his staff. As a result, it was decided to carry on dusting experiments with animals at the mine in a manner that would duplicate as far as possible actual industrial conditions. At that time 50 guinea pigs were placed in the crusher house tunnel of the mill where a considerable quantity of fine dust, containing approximately 35 per cent of free silica, was being constantly produced. These animals lived in this atmosphere for periods up to one year, and, while on autopsy large amounts of dust were found in the lungs, not a single case of silicosis had developed. These negative results suggested, among other things, that the mine gases might be a predisposing factor in the production of silicosis, and the results of this investigation (1) led us to undertake the study of the hydrogen-ion concentration of the condensate of the atmosphere, both in the mine and in various sections of the mill. The CO, combining power of blood serum on a series of 400 miners was also studied at this time. While these results were inconclusive, the variation in the hydrogen-ion concentration of the condensate between the surface and underground atmospheres encouraged us to investigate the effect of neutral, weak acid, and alkaline solutions on the solubility of siliceous materials. Gye and Purdy (2) were the first to point out that the chemical reaction, and not the physical presence of siliceous material, was responsible for the production of the fibrosis in silicosis. This work was investigated by Gardner and Cummings (3), who showed that the tissue reaction to quartz was definitely proportional to the size of the particle. They found that 1-3 micron particles of quartz produced an acute proliferative fibrotic response, while the 10-12 micron particles produced only a foreign-body reaction up to a period of three years. It is accepted that the dangerous silica particles retained by the lung are under 5 microns in diameter.

Jan 1, 1937

By A. Dogan Paktunc

Abstract - The Mechanic Settlement pluton is a small body of mafic and ultramafic rocks of tholeiitic affinity, occurring in the Late Neoproterozoic volcanosedimentary rocks of the Avalon terrane of the Appalachian Orogen. The lenticular-shaped intrusion is layered and consists of ultramafic and mafic lithologies in at least six cyclic units that are relatively thin or short-lived. The lowermost exposed portion of the intrusion is characterized by the cumulate sequences of olivine and olivineclinopyroxene and display relatively flat rare earth element profiles. In the overlying lithologies, plagioclase is the dominant cumulus phase following olivine in the crystallization sequence. Olivine ranges in composition from Fo73 to Fo85 and plagioclase from An62 to An89. Variations in the compositions of orthopyroxene and clinopyroxene are within Wo0-4En52-87Fs11-45 and Wo39-50En23-50Fs3-19. These mineral compositional variations in part reflect cryptic patterns and correspond to normal fractionation trends in cyclic units. Elevated Pt and Pd concentrations of up to 2.6 ppm occur in ten zones within the central cyclic series in association with both the peridotitic and gabbronoritic rock types. The mineralized zones are about several meters thick and appear to have lateral continuities over several hundred meters, suggesting that they are stratiform. Platinum-group elements (PGE) occur as discrete platinum-group minerals (PGM) including vysotskite, merenskyite, michenerite, sperrylite, stillwaterite, and hollingworthite that are associated with magmatic sulfides composed of pentlandite, pyrrhotite, and chalcopyrite. PGM grains range in size from a few micrometers to well above 20 µm. Sulfur isotope ratios and the Se/S ratios of the mineralized rocks are typically higher than the mantle values. Sulfide saturation probably occurred as a result of assimilation of crustal rocks and magma mixing during emplacement of subsequent pulses of magma. Repetition of the PGE mineralization in rather thin cyclic units suggests that the replenishing magma probably had high PGE levels and was saturated with respect to sulfide during emplacement. Ingression of the replenishing magma into the chamber in a turbulent plume and its mixing with the resident magma was probably responsible for the formation of the PGE mineralizations in the Mechanic Settlement pluton.

Jan 1, 2000

By S. Haggarty

"Wholly owned by Corona Corporation, the Nickel Plate Mine is an open pit, gold mining operation located near Hedley, 50 km west of Penticton, in Southern British Columbia.Milling capacity is 3,400 SDT /Day with an average feed grade of 0.080 Oz Au/Ton. Gold processing involves three stage grinding including tertiary pebble milling, two stage cyanide leaching and filtering and Merrill-Crowe zinc precipitation.A summary of process improvements required to increase milling capacity above the initial design tonnage of 2, 700 SDT /Day are described -Installation of a 42"" x 65"" Allis Chalmers Gyratory crusher replacing a 42"" x 48"" Traylor jaw crusher.Installation of polyurethane screen panels replacing woven wire cloths on an 8' x 20 ft triple deck screen.Installation of a hopper clarifier to reduce filtrate turbidity.Automated control of solution balancing and effluent treatment circuits.INTRODUCTIONThis paper describes mining and milling practices at the Nickel Plate Mine and details post start-up process modifications which were required to attain design tonnage.Wholly owned by Corona Corporation, the Nickel Plate Mine is an open pit, gold mining operation located near Hedley, 50 km west of Penticton, in Southern British Columbia.Mining capacity from the open pit is approximately 32,000 TPD with an average waste/ore ratio of 8.4:1.Milling capacity is 3,400 SOT/Day, above initial design tonnage of 2,700 SOT/Day. Feed grade averages 0.08 Oz Au per ton yielding 85,000 troy ounces of gold per year."

Jan 1, 1991

By Brenda M. Dixon

A matrix analysis of the differences between the camps and communities associated with the Britannia Mine is used to develop an analytical tool. The tool is intended to assist the mining industry as it embraces the many facets of sustainable development. A case study is used to support the identification of key factors that may predict the sustainability of a new mine town. Sustainable communities, like Britannia Beach, are discussed in the context of three pillars of sustainability: value of mining products to society; creating wealth; and, environmental integrity. A sustainable mine town may be viewed as a socio-economic asset as well as an asset to the mining industry.

May 1, 2006

By B. G. Cousins, B. O’Rourke, C. Spence

"Some non-flotation chemicals are added to flotation circuits directly and indirectly to control issues such as scaling and dust in other areas of the operations. Since dosage levels are generally not high, a standard laboratory float test may not be able to determine the effect of a specific chemical on the productivity of the flotation circuit. This paper presents a laboratory testing protocol that uses kinetic float studies to test the effect of normal to extreme doses of antiscalant and dust chemistries (5–100 g/t). Results indicate that this protocol helps to predict potential interference by a particular chemistry on the flotation circuit.RÉSUMÉ Certains produits chimiques ne servant pas à la flottation sont ajoutés directement et indirectement aux circuits de flottation afin de contrôler des problèmes tels que l’entartage et la poussière dans d’autres secteurs des opérations. Étant donné que les niveaux de dosage sont généralement faibles, un essai standard de flottation en laboratoire pourrait ne pas être en mesure de déterminer l’effet d’un produit chimique spécifique sur la productivité du circuit de flottation. Le présent article définit une procédure d’essai en laboratoire qui utilise des études cinétiques de flottation pour vérifier l’effet de doses normales à extrêmes de produits chimiques antitartre et anti-poussière (5 à 100 g/t). Les résultats indiquent que ce protocole aide à prédire l’interférence potentielle d’un produit chimique particulier sur le circuit de flottation."

Jan 1, 2016

By P. C. Lighthall, D. W. Zandee, W. Shukin

"IntroductionThis chapter deals with the on land disposal and storage of fine tailing in slurry form behind dams. Other types of tailing, such as coarse dry cobbs from magnetic separation of iron ores and other dry materials, have special problems and are not addressed in this paper. The disposal of mine waste is not included, except as such materials may be of value in the construction activities related to tailing disposal.In earlier North American mining, mines were smaller and frequently disposed of their tailing by direct discharge into neighbouring streams or bodies of water. Where that was not practical or not permitted, the solids were collected in tailing ponds and only the effluent liquids were released or decanted. The dams used for these early impoundments were fragile structures and failures were common. With the advent of large, low-grade open pit mines, and increasing awareness of environmental and safety considerations, recently established mines have carefully-designed tailing disposal systems, with wellconstructed dams and attention given to protection of the environment. Older mines are being improved or at least being examined critically with a view to upgrading as necessary to meet the new standards.Modern tailing disposal systems are highly variable and unique to each mine. Tailing pond selection and design is dependent on available topography as also is the design of transport and water reclaim systems. Suitable sites that are at higher elevations than the mills or distant from them may require that the tailings be pumped. Dams, either earth or rock structures built of the most convenient and economic material, are usually a suitable mix of local borrow, mine waste and coarse tailings. The most economic structures are those built mostly of coarse tailing."

Jan 1, 1989

By Euler De Souza

This paper presents a study conducted to assess sillmat behaviour during undercut mining and to provide a comprehensive understanding of the effects of arching and sillmat thickness on stability. The design study investigated the effects of such parameters as stope width and height, closure strains, orebody geometry and inclination, wall roughness, fill properties and cure time on the stability of cemented sillmat during undercut mining. Arching effects have been quantified based on centrifuge modeling studies for the different mining conditions. Observations have indicated that the degree of arching is a function of stope geometry, wall roughness, fill cohesion, and wall closure. Arching effects increased with decreasing stope width, increasing backfill cohesion and frictional resistance, increasing wall roughness and with wall closure.

May 1, 2002

By Johnna Muinonen

"The Thompson Mill processes ores from the Thompson and Birchtree Mines. While the Thompson ore has very little magnesium containing gangue, the Birchtree orebody consists of veins of massive sulphide in a rock matrix that contains a high proportion of magnesium silicate minerals. A significant fraction of the magnesium is floatable, which lead to MgO levels varying from 3-11 wt% in the Birchtree concentrate. The magnesium in the concentrate causes a higher operating temperature in the smelter, reducing furnace life.Birchtree ore represented 20-30% of the mill ore receipts prior to October 2003. Since then the fraction of Birchtree ore has increased to 50%. A reduction of the MgO in concentrate to less than 3% in the total mill concentrate was required to allow safe and economic smelter operation.In October of 2002 a miniplant was set up to simulate the Birchtree plant circuit. Several flow sheet modifications were tested that led to a proposal for a circuit having increased cleaning capacity for the scavenger concentrate and a recleaner on this concentrate. Addition of CMC in rougher cleaner feed was also found to be required. The solution was confirmed through pilot plant testing in the mill in December of 2002. A full-scale installation was designed, engineered, and installed between February and September of 2003 with commissioning in September and October of 2003. Target metallurgy was achieved one week after start-up on slurry to coincide with the Birchtree Mine tonnage increase. This paper highlights the development, design and commissioning stages of the project.The new MgO rejection circuit has successfully allowed the processing of Birchtree ores producing concentrate consistently below 3% MgO. In addition, the new circuit increased overall nickel recovery in the mill.INTRODUCTIONThe Thompson Nickel Belt located approximately 700km north of Winnipeg was discovered in the early 1950’s. Inco first produced nickel from the area in 1960. Over the years the mill has processed several ores from different ore bodies in the area. Currently the Thompson Mill processes two significantly different ores from two mines, Thompson and Birchtree. The Thompson ore is a massive sulphide orebody hosted in schist, containing feldspars, quartz and biotite. Thompson Ore is characterized by high nickel recoveries and clean, low MgO containing concentrates (<2.5% MgO). The Birchtree ore is ultramafic and contains a high percentage of Mg-silicates such as serpentine, chlorite, biotite, amphiboles and talc. Some of these Mg-silicates report to the nickel concentrate and prior to commissioning of the MgO rejection circuit the Birchtree nickel concentrate typically contained 5-8% MgO"

Jan 1, 2006

By M. Maccagni, J. Nielsen

"The recovery of lead from battery paste has been investigated for a long time and with the use of many different electrolytes. A number of processes have been presented, but none of them reached even the demonstration step. Engitec has developed a new concept for the battery paste electrowinning using a chloride electrolyte fed through a very innovative flow cell. The process has passed the lab and the demo scale and it is ready to be introduced on the market. In this paper, a description of the process will be provided.INTRODUCTIONThe need for improved energy storage systems as well as the introduction of commercially viable electric vehicles is providing a strong compulsion toward the research of new batteries. The lead battery is playing an important role because it is inexpensive, reliable and it is the most recycled material. This last aspect marks the lead acid battery as quite peculiar making it both the primary lead based product and the main raw material for lead production.In the last years the legislative pressure has become very strong and has forced the lead production to react through the introduction of important process innovations and market changes. The dispersive products, such as additives for paints and for fuel as well as bullets, have been practically banned all over the world while the battery market continues to grow. The lead acid battery remains the cheapest and most integrated energy storage system available and is improving to meet the new technical challenges. This is testified by the news coming from the development of new and more efficient lead acid batteries which are confirming their leading position.Unfortunately, the image of lead is very negative in the public opinion and some important actions are required to try changing this sentiment. Among them, better information to the market and users and the introduction of new and cleaner technologies in the production of lead can help."

Jan 1, 2016

By D. Farrish, W. A. Grell

"IntroductionMost base metal mines sell their concentrate to a custom smelter. The two parties concerned therefore draw up a contract which would detail the conditions under which concentrate sales will take place. The contract will identify treatment and marketing charges (including escalations), deductions for metal losses in the smelter, pricing formula, timing of payments, penalties for deleterious elements, etc.An understanding of the smelter contract is important to the mineral processor, for it will determine how he operates the plant to maximize economic return.Description of Contract ClausesUsing copper concentrate as an example, the smelter contract generally contains the following three basic charges:I. Metal Deductions- as the smelting process does not recover all the metal contained;2. A Smelting Charge- expressed per ton of material to cover costs on the bulk material such as receiving, unloading, thawing in winter, sampling, roasting to drive off sulphur, smelting through the matte and blister stages to recover mostof the copper and precious metals;3. A Refining Charge- expressed per pound of copper.The following is a review in some detail of a number of clauses which could be considered typical of a treatment and marketing type of copper concentrate sales contract. Most normal considerations in an agreement could be covered by the following types of clauses.Terminology- covers definitions, units of measurement to be used (e.g. short tons, troy ounces, etc.), currency (Canadian dollars). The term ""unit"" may be defined - l OJo of a ton of concentrate, e.g. one unit of copper means 20 pounds of copper per short ton of concentrate."

Jan 1, 1989

By Robert J. Shank

This paper describes the Federal Government assistance available for northern mining development. The paper commences with a discussion of why the Federal Government should give assistance to northern mining development. It then uses a hypothetical case of a company which has a property it wants to develop to list the sectors within the . Federal Government that would have to be consulted in order to obtain federal financial assistance. The paper also outlines the type of information a company must be willing to provide the government in order to qualify for such assistance.

Jan 1, 1978

By N. C. Karmakar, Y. V. Rao, M. Aruna

No one can properly work without sufficient light and this is especially so in mines where conditions are difficult. Artificial lighting is very important for the night shift to provide a safe and efficient working environment, which must be evenly illuminated with no obvious dark spaces and a minimum amount of glare. During an illumination survey of a large mechanized surface mine, it was found that the illumination level varied and was not uniform throughout the length of the road; it was high at one side of the road instead of at the centre. There were also different combinations of lamps, with angles of light arm varying from 35º to 70º. In this respect, an experimental study was carried out with a fabricated telescopic light pole to uncover the optimum design parameters of lighting installations. The analysis was done by plotting isolux contours for fixed installations and drawing graphs for various combinations of luminaries, reflectors, light arm angles, and height of lanterns by plotting the horizontal angle of the light arm along the abscissa, and the contour area along the ordinate. The study revealed that the design parameters of the lantern are mainly dependent on the type of luminaires. It was revealed that the pot reflector with a combination of tubular bulbs produces a wide distribution of light, and contributes towards a reduction of luminaries when installed in longer roads.

Jan 1, 2005

By F. Chiesa

The permanent mould process, which is a favoured process for producing premium quality aluminium casting, is rarely used to produce magnesium alloy parts. This may be attributed different factors such as: the reservation with which the automotive industry considers using magnesium in structural castings; also the relative hot shortness of most magnesium alloys when compared to aluminium A356/357 is another factor. A third reason stems from the fact that the "heat content" of magnesium is much less than that of aluminium, resulting in the difficulty, for a relatively slow process such as permanent mould (versus pressure die casting), to reach a mould dynamic equilibrium temperature sufficiently high to avoid premature freezing and misruns. The present work will address this problem by carrying out controlled cycling of a laboratory mould, poured with aluminium and magnesium alloys. The influence of insulation of the mould and artificial electric heating on the run-in mould temperature will be determined experimentally. A thermal model will be sought for these thermal devices that will allow to predict the thermal behaviour of moulds of different geometry before a single casting is poured. The model will be tested on an industrial casting in a workshop environment.

Jan 1, 2006

By A. Robles-Vega

Personnel of Mexicana de Cobre, a subsidiary of Southern Copper located in Nacozari, Sonora Mexico have been working in the past few years on the development of a process to treat and manage, in an environmentally accepted practice, the residues and effluents generated during the process. To date, this team has been reviewing existing technologies and also has explored new alternatives. At the end of this phase, a novel, efficient and complete process has been configured which will be able to treat some solid and liquid streams such as Teniente converter dust, Peirce Smith converter dust, a Sb-rich precious metals slag, copper refinery electrolyte bleed, acid plant blowdown and an acid bleed of the precious metals plant. The process will consist of a leaching stage, followed by a very selective copper precipitation using novel technology which has been named as back reactions. After copper precipitation, impurities (As, Sb and Bi) will be precipitated mainly as arsenic trisulfide (As2S3) using H2S(g) which will be generated by means of a new process developed in our company. At the end of the process, small volumes of arsenic trisulfide will be vitrified and then disposed as a stable residue.

Jan 1, 2007

By O. Matwijenko

"The Kidd Creek concentrator is located twenty-six kilometres east of Timmins, Ontario, within a metallurgical complex including a 109,000 MTPY zinc plant and a new 59,000 MTPY copper smelter and refinery. A complement of 159 persons is employed in the operation of the concentrator.Ore from the Kidd Creek Mine is crushed underground to minus 15. 0 cm, then transported twenty-seven kilometres by rail 1:0 the concentrator. After being crushed to minus 1. 6 cm, the ore is further processed by grinding and flotation.The concentrator commenced operations in November of 1966 at a designed capacity of 8,200 MTPD. Two parallel flotation and grinding circuits treated copper-zinc ore (2.28% Cu, 5.63% Zn) and a third treated silver-copper-lead-zinc ore (230 g/MT Ag; 0.57% Cu, 0.88% Pb, 7.89% Zn).By 1975, the concentrator was treating 9,100 MTPD of ore. Seven concentrates were being produced, namely, high silve1: copper, low silver copper, lead, low silver zinc, high silver zinc, pyrite and tin.Planned minesite expansion to a second underground mine required increased concentrator throughput. Expansion of the concentrator enabling a thirty-three percent increase in copper-zinc ore throughput occurred during the period 1975 through 1978. This expansion included increased load-in capacity, major redesign in the crusher house, the addition of a fourth grinding and flotation circuit, the building of a fourth dryer, and numerous expansions of services."

Jan 1, 1980

By D. A. Livingstone

"INTRODUCTORY REMARKS BY PANEL CHAIRMAN - D. A. LIVINGSTONEThe mining industry has progressed significantly from the dusty mines and mills of decades past to the modern processing complexes of today, and improved technology has made great strides in eliminating debilitating lung discuss. More recently, the public's environmental awareness is also working to enforce more stringent regulations and controls in tl1e matter of dust in working places.There are numerous excellent texts and handbooks outlining the principles of collection of dust produced in the various unit operations entailed in the crushing, screening and the transport of ore. However, it is painfully obvious that dust emanating from belt return idlers and scrapers, take-up pulleys, skirting, larger and deeper chutes, clean-up operations, etc., which I choose to refer to as fugitive dust, presents some seemingly unmanageable difficulties, or at least difficulties inordinately costly to correct. Possibly static electricity is adding to the difficulties. In my view, these problems are magnified in many of our B. C. operations where ore from open pit mines in cold climates is frequently crushed in unheated buildings, thereby precluding the simple and obvious use of water sprays for dust suppression.It is hoped that the presentations and discussion which follow will emphasize some of these unusual problerr.s and suggest corrective measures, either tried or planned."

Jan 1, 1976

By A. A. de Gast, R. B. James

"The metal content of ore blocks can be calculated by the use of many different methods. These methods range in sophistication from manual calculation to computer. oriented techniques. In this case a cubic polynomial regression model is developed to depict the grade distribution of an orebody. Mine production, in stope dimensions, is then simulated on a computer to predict the output of metal content. The volume, grade and variance of the grade are estimated by triple integration and matrix algebra. A case study shows reasonable agreement between the results from the mathematical model and the mine geologists' estimate of production and ore reserve grade and tonnage."

Jan 1, 1972