Search Documents

By B. A. Watters, G. A. Parslow, F. H. Mcdougall

Carbonate-rich rocks occur at several localities within the Flin Flon volcanic sequence of the eastern Amisk Lake area. The rocks occur in two areas: as a group of small occurrences on islands within Amisk Lake and as two much larger linear belts running parallel to the regional structure east of Amisk Lake. Mineralogically, the rocks consist of talc and Ca-poor ankerite with occasional graphite. Segregation of these minerals and colour variation impart a well-defined planar fabric to the rocks and where the units are fairly continuous (e.g. Mosher Lake), their trend and attitude suggests a concordant relationship to the volcanics. Major and trace analysis of22 samples confirms the presence of two types, with one type being represented in each of the two areas. Most of the elements studied can be used to characterize the two groups, but three elements in particular give a clear separation: Mg, AI and Ni. Recalculation of the major element analyses, on a water and carbonate-f ree basis, indicates that one group (large concordant bodies with high MgO, high Ni and low AI20.J is altered ultrabasic material of peridotitic or dunitic composition. Because no relict igneous material is observed, and the contacts are apparently very sharp, it is possible that the hydration-carbonization process occurred simultaneously with intrusion, .in a closed system. The other group (small occurrences with relatively low MgO, low Ni and high AI203J represents alteration of basaltic rocks. AIthough some analyses suggest the introduction of calcium, as carbonate, along with the volatiles, the major oxides have remained remarkably stable during the alteration process(es).

Jan 1, 1981

By C. Campero, C. Nicolau, L. Pagliero

The Chilean Congress has recently promoted desalination as a solution to meet the mining industry’s growing water demand. However, this rapid expansion of desalination infrastructure comes with trade-offs. This includes a significant energy cost for treatment, as well as socio-environmental impacts on indigenous communities, tourism, fisheries, and the marine ecosystem. This paper advances a regional-scale model for analyzing competing trade-offs through a case study in the Antofagasta mining region of Chile. Through geospatial data analysis in ArcGIS, new desalination infrastructure investments supplying water to mines are overlain with features of concern raised by communities during the environmental impact assessment (EIA) process, such as national parks, fisheries and exploitation areas for benthonic resources. The resultant model provides a test-bed for analyzing the cumulative effects associated with desalination expansion and for investigating scenarios to mitigate negative social-environmental impacts. The model simulates alternative scenarios for desalination locations and pipeline routes according to competing constraints (i.e. to minimize cost and energy constraints while also avoiding ecological and social hotspots). The ultimate contribution of the work is a demonstration of how the proactive adoption of a regional-scale infrastructure planning might have led to different desalination investment decisions. INTRODUCTION Chile represents the largest producer of copper globally, and holds approximately a third of the world’s estimated copper reserves. However, access to water represents a major constraint to industry expansion and creates conflicts with competing water users (Aitken et al., 2016; Côte et al., 2010). Recently, the Chilean Congress has promoted desalination as a solution to meeting the industry’s growing water demand, which is likely to lead to significant growth in desalination infrastructure to support large-scale mining projects that extract freshwater over a rate of 150 l/s1. By most recent projections, the Chilean copper mining sector is set to increase seawater use by 230% by 2029 (Faversham House Group Ltd, 2019). By the year 2015, Chile had 11 projects serving the mining industry and there are at least other 12 planned plants (Cochilco, 2015). While the use of seawater allows continued expansion of the sector without depletion of scarce underground aquifers, it is nonetheless accompanied with important socio-environmental drawbacks. One such challenge with desalination is the associated energy costs, expressed, both economic and environmental (e.g., CO2 emissions). This includes the energy required for reverse osmosis treatment facilities, as well as to pump water to inland regions at high elevations around 3.100 m.a.s.l in Chile. (Dixon, 2013; Knops et al., 2013). Additionally, the impacts of desalinated water use on flotation chemistry are generally poorly understood, necessitating the need for further research into the impacts, both positive and negative (Cisternas and Gálvez, 2018; Liu et al., 2011).

Jan 1, 2019

By D. K. Fountain

"High metal prices and advanced technology in open-pit mining methods have resulted in considerable interest in the development of large, low-grade mineral deposits. Brenda Mines Limited is presently testing such a deposit of copper-molybdenum mineralization near Penticton, British Columbia.The mineralization of economic interest at Brenda has a total metallic sulphide content of between 1 and 1.5 per cent. This sulphide content approaches the limits of detectability of standard geophysical methods. How-ever, due to a favourable geological environment, it has been possible to utilize the Induced Polarization Method to outline the mineralization at the Brenda property."

Jan 1, 1968

By R. K. Mishra, A. Kula, X. Jia, M. Niewczas

The mechanical properties of Mg-Gd and Mg-Y solid solutions have been studied under uniaxial tension and compression between 4K and 298K. The results reveal that Mg-Gd alloys exhibit higher strength and ductility under tension and compression attributed to the more effective solid solution strengthening effect and grain boundary strengthening. Profuse twinning has been observed under compression, resulting in a material texture with strong dominance of basal component parallel to compression axis. Under tension, twining is less active and the texture evolution is affected mostly by slip. The alloys exhibit pronounced yield stress asymmetry and significantly different work-hardening behaviour under tension and compression. Increasing of Gd and/or Y concentration leads to the reduction of the tension-compression asymmetry due to the weakening of the recrystallization texture and more balanced twinning and slip activity during plastic deformation. The results suggest that under compression of Mg-Y alloys slip is more active than twinning in comparison to Mg-Gd alloys.

Jan 1, 2015

By Z. Bibak, S. Banisi, A. Ghasemi, E. Nematollahi

"The major importance of liners in grinding is their role in providing an appropriate trajectory for the charge. Since it is not possible to study the charge movement by direct observation in operating industrial mills, this task is accomplished by physical (laboratory), and/or, mathematical (software) methods. Because of the high cost and a longer time required for a physical analysis, mathematical simulations have become more common. Simulation of the effect of liner shape on the charge movement has provided a means to select a proper design based on the operational objectives and conditions. Furthermore, the liner shape changes due to wear and impact during operation, which will influence the charge trajectory. This adds more of an incentive to use simulation. These changes in liner could be predicted through liner profile measurements during operation and/or simulation. In this research, an inhouse developed DEM software called KMPCDEM © was used to simulate the charge movement in industrial plant SAG mills. A geometrical method of implementing the shell liners on SAG mills at the Sarcheshmeh (9.75×4.87 m) and the Gole-E-Ghohar (9×2.05 m) operations facilitated the software simulation. Point by point implementation of the measurements of liner profiles of these mills enabled the study to trend the change in the charge movement as the liners wear. Comparison of the simulation to a laboratory mill (1 m diameter) showed that the difference between the measured and predicted charge impact point, shoulder angle and toe angle were 6, 4 and 3°, respectively.INTRODUCTIONComminution is the most energy intensive operation constituting the major portion of operating and capital costs of a mineral processing plant. In the last decade, a vast number of research was aimed at studying various aspects of grinding with the aim of performance improvements (Davis, 1919; Mishra & Rajamani, 1990; kalala, Breetzke, & Moys, 2008). Mill liners transfer the input power to the charge and play a significant role in affecting the motion of the charge (Mclvor, 1983; Mishra & Rajamani, 1990; Radziszewski, 1997; Van Nierop, Glover, Hinde, & Moys, 2001; kalala et al., 2008). Lifters are usually used with mill liners to extend their life and to enhance the grinding and impact breakage efficiency. Mill lifters are used to raise the grinding media and ore to transfer the energy from the mill to the load (Rezaeizadeh, Fooladi, Powell, & Weerasekara, 2010)."

Jan 1, 2016

The Carboniferous sedimentary rocks of southwestern Newfoundland merit investigation because of petroleum, salt and gypsum possibilities and indications of base metallization along the equivalent of the Horton-Windsor con-tact. In this paper, Lower Mississippian (Anguille) strata are divided into three formations: (1) the Cape John below, (2) the Snakes Bight and (3) the Seacliffs. A correlation between these formations and the Craignish, Strathlorne and Ainslie formations of the Horton group? in western Cape Breton Island is suggested. The criteria for the Anguille subdivision are essentially lithological, but preliminary study of included spore assemblages suggests more precise interformational correlations between Anguille and Horton sequences. The re-measured lower portion of the type section of the Codroy group is presented to define more clearly the stratigraphic position of numerous gypsum and limestone beds. Because of rapid facies changes within the Codroy group a simplified two-fold division into upper and lower units is proposed on the grounds of

Jan 1, 1964

By B. J. Keating

"AT PRESENT, it is not certain that any of the sulphide de in the Province of Nova Scotia attain the lower grade limit of 60 per cent sulphides over the minimum area of 1,000 square feet suggested as cut-off specifications for inclusion in this Symposium. However, several of them do include massive sections of substantial size and others represent concentrations of sulphide material that are well above average. It is felt, therefore, that a tentative classification of the deposits and presentation of their geological settings are justified and may help round out the genetic aspects of this study. Accordingly, data considered to be the most pertinent are assembled here in the event that some may fit into larger-scale patterns of mineralization that may take shape as a result of this investigation.The three principal massive sulphide deposits in Nova Scotia are the Stirling, the Smithfield, and the Walton. The locations of these are shown on the accompanying key-map (Figure 1).Three other deposits, the locations of which are also indicated on the map, are the Meat Cove, Rocky Brook, and Gays River de¬posits. Although these fall far short of the minimum dimensions and grade specifications referred to above they are singled out because they have received more than passing attention and are illustrative of the mineralization types to which they belong."

Jan 1, 1960

By F. T. Mooney

Introduction The Flin Flon mine of the Hudson Bay Mining and Smelting Company, Limited, is on the interprovincial boundary between Manitoba and Saskatchewan, about four hundred miles north of the Canada-United States boundary. The orebodies are gold, silver, zinc, and copper replacement deposits occurring as irregular lenses of massive sulphides, arranged en echelon, and irregular masses of disseminated copper sulphides in chlorite. The country rocks are of Precambrian age, dominantly lava flows. Development of the Mine The mine is opened by two vertical main shafts- the North Main and South Main shafts- 3,800 feet apart. The North Main shaft has a depth of 2,210 feet and the South Main shaft is completed for stoping operations to the 3,250-foot level (see Figure 1). These shafts are connected by main haulages driven, on the footwall side of the orebodies, at 520-foot intervals down to the 2,210-foot level. No. 3 (subsidiary) shaft is on the footwall side of the orebodies at a point between the North Main and South Main shafts, 2,400 feet south of the former. It has a depth of 3,250 feet and connects with all main haulage levels- with both Main shafts down to the 2,210-foot level and with the South Main shaft on the 2,750-, 3,000-, and 3,250-foot levels. Other openings tO the mine include B North fan raise, the opening due to the recovery of the open pit sill pillar, and several back-fill raises.

Jan 1, 1949

By M. Bélanger, H. -L. Jacob

"The province of Quebec has a strong tradition in industrial minerals. Ten commodities are produced and the annual total shipments have exceeded $600 million in recent years. Quebec is a world renowned producer of chrysotile, titanium slag, graphite, and ilmenite. Quebec is an important North American producer of mica, talc, and peat moss. This paper reviews the main minerals and commodities that have been the object of exploration or development in recent years, namely graphite, wollastonite, dolomite, and silica. Some of the leading projects concerning magnesium minerals and apatite-ilmenite are described. IntroductionQuebec has a strong tradition in industrial minerals. It goes back to the second half of the 19th century when the first graphite and apatite mines in the Gatineau area and asbestos mines in the Eastern Townships were opened. Since then, more than 25 commodities have been produced in Quebec, making industrial minerals an integral part of the Quebec mineral industry. Today, industrial minerals and building materials count for one third of the total mineral production in Quebec.Present industrial mineral production includes 10 commodities (Table 1). In the last five years, the value of industrial mineral shipments has varied between 500 and 700 millions dollars annually, which represents 20% to 25% of Quebec’s total mineral production. For many years, Quebec has been a major producer of chrysotile and titanium slag, the only producer in eastern North America of mica, graphite and ilmenite, and a leading Canadian producer of talc and peat moss. Quebec also produces, mainly for domestic markets, dolomite, limestone, salt and silica.Quebec’s industrial mineral sector has been quite active in the recent years. Exploration by government geologists and companies has led to the outlining of new deposits, some of which are now in production; others are currently being evaluated. Technical and economic studies are also underway to determine the feasibility of various development projects."

Jan 1, 1999

By M. S. Badollet

Introduction Very little fundamental research has been done on asbestos fibre to cake maximum advantage of its properties and to determine in what commercial products it can best be utilized. For the research chemist who is associated with asbestos development work, a thorough study of mineralogical information on asbestos deposits would furnish reliable information on the rock formations and the mineral impurities closely associated with the asbestos. Furthermore, ?he must have an intimate knowledge of the uses of the fibre in various products so that he can visualize the importance of the fibre and the role it plays in industry. Some of the properties of asbestos fibres such as strength, composition, length, harshness or softness, and mineral associates are of considerable importance to the manufacturer because they are responsible for many production difficulties. Fibre Strength It has been known for some time chat asbestos filaments have considerable tensile strength. These strengths have been referred to merely as 'weak' to 'very strong'. Not until recently have numerical values been applied to the strengths of asbestos fibres. But today we can take a thin fibre filament and mount it between two holders and apply a gradually increasing load or pull until the fibre breaks. By measuring the cross sectional area of the filament and the amount of load applied, we can calculate the tensile strength of the fibre in terms of pounds per square inch. This type of test is slow and rather difficult, but the fundamental data obtained furnish important basic information that can be applied to mechanical processing equipment and to certain asbestos products.

Jan 1, 1948

By K. K. Dehn

This study focused on determining the stability of thin shotcrete fill fences at a hard rock mine in northwestern Ontario during increased pour rates of paste backfill. Determination of the stability of the fence is needed for both personnel safety and to avoid failure of a fence. Failure of a fill fence during backfill activities would have severe impacts on production and potential hazards to nearby workers. Approved fill fences at the mine are a slender design of 10.5 centimeters of shotcrete applied to a rebar framework with burlap lined ?bedspring? backing. Approved mine standards dictate that fill rates may not exceed 1.5 meters of paste depth per 10-hour shift when pouring behind a flat fill fence. To decrease the backfill cycle time the study looked at fence stability during increased pour rates of 2.5 meters paste depth poured within a 10-hour shift. An instrumentation design was developed including pressure cells, strain gauges, and tilt-meters that were built into experimental fences to observe the effects of increased pour rates on lateral wall pressures, strain development in the rebar and shotcrete reinforcement, and physical deformation patterns along the face of the fence. The data was analyzed for overall stability.

May 1, 2007

By L. A. Jameson, J. Awmack, P. J. Lind

"Peñasquito is a polymetallic deposit containing gold, silver, lead, and zinc. The operation is currently the largest producer of gold in Mexico. Over the next few years, the process flowsheet will be expanded beyond the flotation of lead and zinc to include flotation of pyrite from zinc tails and subsequent leaching of the pyrite concentrate. This paper outlines mineralogical leach characterization that has been carried out to improve the understanding of the complex hosting of gold and silver minerals in the ore. Organic carbon that is present in the ore can have an impact on flotation and leaching. Mineralogical techniques used to characterize this deleterious component of the ore are introduced.INTRODUCTION Goldcorp’s Peñasquito operation is located in the Mexican state of Zacatecas, approximately 200 km from the city of Zacatecas as shown in Figure 1. Peñasquito has been in operation since 2009 and is currently Mexico’s largest gold mine. Mining is carried out by open-pit methods, with oxide ore proceeding to a heap leach facility and sulfide ore treated in the sulfide processing plant.The processing capacity of the sulfide plant is 130,000 tonnes of ore per day and in 2016 production amounted to 450,000 ounces of gold, 17.6 million ounces of silver, 109 million lb of contained lead, and 263 million lb of contained zinc in lead and zinc concentrates. GEOLOGY The Peñasquito deposit is hosted in and adjacent to two breccia pipes; Peñasco and Breccia Azul. The two breccia pipes are branches of a larger intrusive-related complex, which is hosted in the sedimentary Caracol formation as illustrated in Figure 2. The regional geology is dominated by Mesozoic sedimentary rocks which comprise a thick series of marine sediments deposited during the Jurassic and Cretaceous periods. A 2 km thick sequence of carbonaceous and calcareous siltstones and interbedded sandstones is underlain by a 1.5 to 2 km thick limestone sequence (Goldcorp Inc., 2015)."

Jan 1, 2017

By Denis Blackburn

La Direction générale du développement de l?Industrie minérale (DGDIM) du ministère des Ressources naturelles et de la Faune (MRNF) du Québec tient un inventaire de toute l?activité minière sur le territoire. Cet inventaire s?est enrichi, au cours des dernières années, d?un grand nombre de projets dédiés au fer ou à des substances qui y sont associées (titane, vanadium, phosphate). Actuellement, cinq régions du Québec sont principalement touchées par la recrudescence de projets dédiés au fer : Fermont, Schefferville, Baie d?Ungava, Baie-James et Chibougamau. Fermont et Schefferville sont les régions les plus actives. Les infrastructures en place, telles que les routes, les chemins de fer, les ports, les lignes électriques et les municipalités, ont atteint, dans certains cas, leur capacité et de nouvelles infrastructures devront être construites pour satisfaire les besoins. À la Baie-James et sur le flanc ouest de la Baie d?Ungava, des projets d?exploration sont aussi en cours. Le manque d?infrastructure pourrait peser lourd sur le développement de projets miniers dans ces régions. Enfin, dans le secteur Chibougamau/Matagami et à quelques sites ailleurs au Québec, des projets d?exploration qui visent le vanadium, le titane ou le phosphate pourraient aussi fournir comme produit secondaire des concentrés de fer. Tous les projets, décrits dans cet article, sont situés sur le territoire du Plan Nord du gouvernement du Québec.

May 1, 2011

By S. B. Ballantyne, D. R. Boyle

"Detailed studies have been conducted on the dispersion of uranium in stream waters and sediments around various types of mineralization and hitherto unexplained anomalous areas in the Okanagan Valley and Highland region of south-central British Columbia. These studies were part of the jointly funded and planned Federal-Provincial Uranium Reconnaissance Program of the Geological Survey of Canada and the British Columbia Ministry of Energy, Mines and Petroleum Resources. Statistical analysis of regional data indicates that U in stream waters and sediments varies considerably for different rock types, thus affecting data interpretation. In addition, the data demonstrate a poor correlation between U in stream waters and their associated sediments which can be largely accounted for by variations in climate and water and sediment composition. Regional trends in the distribution of U can be explained in terms of the above secondary factors as well as primary metallization phenomena.Significant correlations between U and F, and U and Mo can be explained by certain magmatic and mineral-forming processes. U shows little correlation with other base metals.The dispersion characteristics of U in the vicinity of Miocene "" basal type "" mineralization ; uraniferous pegmatite terranes, anomalous lineaments in granitic terranes and high-background volcano-sedimentary areas are discussed. Highly anomalous U concentrations in waters and sediments may not always be indicative of mineralization, and guidelines for interpretation require a sound knowledge of the geological and secondary processes operative in the area."

Jan 1, 1980

By G. Viramontes-Gamboa, A. Encinas-Oropesa, S. Velázquez-Roque, L. A. Ibarra-Bracamontes

Some industrially relevant applications for pyrite nano/micro-particles have been proposed in the literature, such as the catalysis of chalcopyrite leaching, the removal of As(III), As(V) and Cr(VI) from solution, as photovoltaic devices, and others. Even though pyrite can be recovered from solution by flotation, for some applications it may be beneficial to provide pyrite with magnetic properties. In this work, a methodology to synthesize magnetic shell/core composites made of pyrite as the shell and either natural or synthetic magnetite as the core is presented. The size of the magnetic composite may range from tenths to hundreds of microns. The synthesis is basically made by stoichiometrically mixing iron nano/micro-particles with sulfur microparticles with magnetite particles, and bringing the mixture in an oxygen free atmosphere from 200 to 300 °C for 4 h. The composites were characterized by optical microscopy, Scanning Electron Microscopy and X-Ray diffraction.

Jan 1, 2014

By Jirí Faltus

The paper deals with studying the impact of structural properties and anodizing of surface on the corrosion properties of extruded rods from commercial aluminium alloys: AA6082, AA6262, AA6012, AA2007 and new lead-free aluminium alloys AA6023, AA2015 and AA2111B. Samples were exposed to the corrosive atmosphere NSS, AASS in the chamber by EN ISO 9227. Surface of samples were either in the original state or anodizing by selected mode. The depth of corrosion attack and the form of corrosion attack are evaluated depending on the type of alloy, the metallurgical condition and surface treatment of the samples.

Jan 1, 2015

By G. A. Gross

Nearly 90 per cent of the iron ore produced in Canada is derived from iron-formation or bedded iron deposits. About 70 per cent of this consists of concentrates obtained fom iron-formation; another 20 per cent was formed by natural enrichment processes. Four principal varieties of iron-formation are recognized -the Algoma, Superior, Clinton and Minette types. Differences in their geology, mineralogy, chemical composition and environment of deposition are of special significance in their evaluation as ore.

Feb 1, 1966

By S. P. Lowe

Introduction In the following pages a general description is presented of the concentrator and cyanide plant of the Hudson Bay Mining and Smelting Company, Limited, at Flin Flon, Manitoba, together with some account of the steps which have led to the adoption of the present practice. For an account of the preliminary test-work and pilot-mill operation, the reader is referred to a recent paper by R. E. Phelan on the History of Flin Flon Mine up to Construction (1). Additional notes may be found in a paper which the writer presented at the Annual Meeting of the Institute in 1930 (2). The first ore was crushed in the present plant on July 1st, 1930, and the first ball-mill was started one month later, on August 1st. Since that time, production has been continuous with the exception of one month lost during a strike in the summer of 1934. There have been no major changes in equipment or methods of treatment since the present plant was built, but many minor changes have contributed to the improvement in results obtained and to the increase in capacity to the large tonnage now being milled. The accompanying flow-sheets indicate the equipment used in the several plants, with the average life and repair cost. As originally built, the concentrator was to treat 3,000 tons per day, but the capacity has been increased to 4,400 tons. The methods adopted to make possible this increase in tonnage will be referred to below. It was the intention to produce two classes of ore: (1) a heavy sulphide, and (2) a disseminated ore. The mill was consequently divided into two sections, each adapted for most efficient treatment of one particular type of ore. However, it was soon found that it would be impossible to mine the two classes of ore separately, so it was decided to treat open-pit ore, which varies greatly in character, in the sulphide section, and underground ore, which is fairly constant, in the disseminated section. This segregation is still maintained.

Jan 1, 1935

By M. Dadvand, G. Kipuros, A. Dadvand

"The ability to codeposit fillers within a nickel matrix has led to the production of a new generation of cermet coatings with properties useful for various applications. Hexagonal boron nitride (hBN) is a ceramic-type particulate matter with thermal conductivity, thermal stability, inertness, and lubricity properties that allow it to be codeposited. In this paper, a method was developed for modifying hBN surfaces to allow them to be uniformly dispersed in water-based solutions such as an electroless nickel plating bath. hBN surface modification improved wear performance of the electroless plated cermet due to enhanced interaction between the particulate and nickel matrix. RÉSUMÉ La capacité à effectuer un dépôt simultané de charges dans une matrice nickel a abouti à la production d’une nouvelle génération de revêtements cermet (une combinaison de céramique et de métal) dotés de propriétés très utiles pour diverses applications. Le nitrure de bore hexagonal (h-BN) est une matière particulaire de type céramique utilisée pour ses excellentes conductivité et stabilité thermiques, son inertie ainsi que son caractère lubrifiant, qui permettent son dépôt simultané. Cet article explore une méthode mise au point pour modifier les surfaces du h-BN de manière à ce qu’elles se répandent uniformément dans des solutions aqueuses telles qu’un bain de dépôt autocatalytique de nickel. La modification des surfaces du h-BN a amélioré la résistance à l’usure du placage autocatalytique du cermet en raison d’une interaction accrue entre la matière particulaire et la matrice nickel.INTRODUCTION Electroless nickel alloy coatings can be used for many applications; however, the need for improved tribological properties such as higher wear resistance and better lubricity has increased interest in incorporating particulates (fillers) into the nickel matrix by codepositing the particulates with nickel during the plating process. The selection of the particulate type depends on the desired properties (Sahoo & Das, 2011; Sudagar, Lian, & Sha, 2013). In terms of tribological applications, electroless nickel-based composites are categorized mainly into lubricating and wear-resistant composite coatings depending on the type of particles incorporated. The electroless nickel-phosphorus (Ni-P) composite coatings are composed of codeposited solid lubricants such as polytetrafluoroethylene (PTFE), graphite, WS2, MoS2, and hexagonal boron nitride (hBN) and, compared to nanocomposite electroless Ni-P coatings, they demonstrate a lower coefficient of friction. On the other hand, the nickel-phosphorus wear-resistant composite coatings are composed of hard particles such as silicon carbide (SiC), aluminum oxide (Al2O3), boron carbide (B4C), silicon nitride (Si3N4), diamond, tungsten carbide (WC), and zirconium oxide (ZrO2) and, compared to nanocomposite electroless Ni-P coatings, they have higher hardness and better wear resistance (Sahoo & Das, 2011; Sudagar et al., 2013; Parucker, Klein, Binder, Ristow, & Binder, 2014; Chakarova, Georgieva, Petrova, Dobreva, & Stoychev, 2016)."

Jan 1, 2018

By P. Pal Roy, R. B. Singh

"This paper focuses on a number of interesting results to establish the theory and principle of air-deck blasting. It also gives the mechanism of breakage that takes place in air-deck blasting under varying charge load conditions. With these aspects in mind, the mine management can implement this up-coming technology to enhance safety and higher productivity. IntroductionThe method of air-decking has become an increasingly popular technique in production and presplit blasting. In the blasthole, an explosive column is combined with an airchamber. The main aim of the technique is to control breakage through effective distribution of explosive energy and thereby enhance uniform rock fragmentation. An air column lowers the initial pressure of the explosive products and simultaneously increases the time of interaction for the detonation front with the surrounding rock, which enhances rock breakage.To study air-deck blasting, CMRI initially conducted experiments using indigenously developed, low-cost wooden spacers of different sizes and strengths. Air-deck blasting was first tried using these spacers in 1993 at Jambad OCP, ECL and Chasnalla OCP, IISCO. The experiments were extended in 1994 at Bermo Mine, DVC. The results were subsequently published by Pal Roy et al., in 1995. It is worth mentioning that the performance of air-deck blasting during this period was only compared with conventional blasting practices without going into detail of the theory behind the process."

Jan 1, 2001