Search Documents

By M. A. Tomlinson, A. Di Feo, T. C. Cheng

"Goldcorp is evaluating the potential for economic reprocessing of historic tailings at several sites, including the Aunor A facility located in Timmins. The overall project is investigating the ability to recover value, remove sulphide minerals and alternative tailings re-deposition strategies. Desulphurization of tailings will eliminate potential acid generation while improved tailings re-deposition could reduce long-term liabilities and closure costs. Through a task-share project between CanmetMINING and Goldcorp, tailings obtained from Aunor A site have been characterized using mineral association analysis and diagnostic separation techniques. The selected tailing samples contain about 2 g/t of gold. Mineralogical analysis has identified coarse agglomerates bound with gypsum and significant free gold, confirmed by high recoveries in cyanide leach tests. However, despite no evidence of surface passivation on the minerals, conventional flotation techniques were found to be ineffective in concentrating gold or sulphides due to the high fines content and highly agglomerated particles.INTRODUCTION Aunor Mine is one of the historic mines that belongs to Porcupine Gold Mines (PGM) in Timmins, Ontario. PGM has undertaken an extensive mine closure program to remediate the legacy and closed mines with the funding supported by operating mines since 2006. Over the course of 100 years of operation in the Porcupine camp, it is estimated (Stevens et al., 2013) that about 130 million tonnes of tailings have been generated. Aunor Mine produced 2.5 million troy ounces of gold between 1940 and 1984, while processing over 7.6 million tons of ore. The original gold grade of Aunor Mine ores was about 10 g/t. With 95% gold recovery at the time, an estimate of 0.5 g/t of gold remains in the Aunor Mine tailings. Aunor Mine has two tailings impoundment areas: designated as Aunor A and Aunor B. The two sites are similar in size, about 7 hectares each. The amount of tailings in the Aunor A site alone is about 3.2 million tonnes. In 2017, bulk tailings were sampled from five designated locations in Aunor A. They were characterized using mineral association analysis and diagnostic separation techniques. The bulk tailings samples contained about 10% total sulphur, 10% iron, 2% arsenic and 2 g/t of gold. The prime objective of this collaborative work between CanmetMINING and Goldcorp is to facilitate the timely development and deployment of innovative tailings reprocessing solutions, specifically in the areas of desulphurization, and recovery of metals. This work targeted specific tailings of interest to Goldcorp which goals are to improve its environmental footprint and to reduce long-term liability. Thus, it is imperative to look for innovative reprocessing options that can overcome not only technological challenges but also achieve economic benefits to offset the costs associated with reprocessing the tailings. Moreover, the greater goal is to demonstrate and deploy tailings reprocessing solutions to solve one of the industry’s most difficult challenges for a sustainable mining industry in Canada."

Jan 1, 2019

By Ashu Garg, Anirban Bhattacharya

"Friction stir spot welding of aluminum alloy AA6061-T6 sheets was performed with circular (plunge depths 0.4 and 0.6 mm), square and triangular tool pin (plunge depth 0.4 mm) with constant 0.2 mm shoulder penetration to characterize various zones of weld nugget. It was observed that the depth of the stir zone formed below the tool pin is comparatively similar for different tool pins but wider for circular tool pin. The size of another stir zone formed at the interface of tool pin and a tool shoulder is observed to be larger for triangular and square tool pin due to the higher swept rate. Predicted strain from finite element analysis, calculated strain rate using Zener-Hollomon relationship and experimentally measured grain size distribution indicates severe amount of plastic deformation in-and-around the nugget/spot region. Finer grains in various stir zones were observed than thermo-mechanically and heat affected zones. Grain size (at distribution peaks) in stir zones varied around 2.54 µm to 3.69 µm for different tool pin profiles as compared to base metal grain size of 20 µm. Microhardness results indicate that the welded region is quite softened than base metal and maximum hardness is mostly observed around the thermo-mechanically affected zone.INTRODUCTION Friction stir spot welding (FSSW) is widely used for joining the sheets of materials like aluminum, copper, magnesium, etc. The process begins by plunging a rotating tool (generally having a pin and a shoulder) into the sheets to be welded. Continuous stirring of the tool and downward plunging force generates localized heat due to friction at the tool-sheet interface and plastic deformation of the sheet metal. The material gets softened and the plasticized material adjacent to the tool pin starts flowing due to the action of tool rotation and tool plunge thereby causing intermixing and bonding between the overlapped sheets. The tool stirring also promotes grain refinement in the weld nugget associated with high strain, strain rate and thermal cycle. The formation of new microstructure also affects the mechanical properties and efficiency of FSSW joints. Studies also showed that the tool pin design and tool shoulder feature exerts a noteworthy influence on the material flow and intermixing during the FSSW process (Reilly et al., 2015; Hirasawa et al., 2010). Sarkar et al. (2016) studied the material flow and intermixing during FSSW using tracer material method and reported that the size and width of flow zone increases with tool penetration depth. The influence of tool rotational speed on microstructure and stir zone temperature was investigated during FSSW of dissimilar AA6061-AA5754 alloys (Gerlich et al., 2007). They reported that the average grain size in stir zone of AA6061 weld increases with increase in tool rotational speed. In another work, Gerlich et al. (2008) studied the local melting and tool slippage during FSSW of Al alloys. Tool slippage was investigated by calculating the strain rate using Zener-Hollomon relation. Garg and Bhattacharya (2017a) studied the effect of dwell time, tool pin profiles and tool rotational speed on shear strength, microstructure, temperature and strain distribution during FSSW of AA6061. In another work, Garg and Bhattacharya (2017b) analyzed the effect of different tool pins and pinless tools on the shear strength and microstructure during similar and dissimilar FSSW of AA6061-T6 and pure Cu. Chang et al. (2004) proposed mathematical relationship between the average grain size and Zener-Hollomon parameter during friction stir processing of Mg alloy. Solhjoo (2010) presented a mathematical approach to determine the critical strain as a function of peak strain required for initiation of dynamic recrystallization in austenitic stainless steel. Fratini and Buffa (2005) also proposed the numerical model to determine the grain size during continuous dynamic recrystallization phenomenon."

Jan 1, 2018

By G. Zárate, G. Tapia

Anglo American Chile has been doing copper concentrate leaching studies at the laboratory and small pilot plant scale since 1992. Among the processes evaluated are bacterial leaching and pressure leaching using Mantos Blancos, Salobo Project and Quellaveco Project concentrates. Late in the nineties, it was decided to focus the research on pressure leaching, either medium or total pressure oxidation. Preliminary scouting tests were run with Mantos Blancos concentrate samples during 2000, which were repeated during 2003 together with samples of Los Bronces and El Soldado concentrates, in order to define the most suitable concentrate for running a pilot plant campaign at AARL, which was carried out in two campaigns, a first one from November 2003 through January 2004 and a second one during April 2004. Mantos Blancos was the selected concentrate and the laboratory and pilot plant results are discussed in this paper together with some preliminary economic estimates.

Jan 1, 2004

By N. Shi, T. G. Joseph

ABSTRACT One-twentieth-scale field trials for conventional and concept dipper designs were compared to mid- and ultra-class-sized conventional dipper performance. Digging effort was used as the performance indicator for comparison. It was shown that linear relationships exist between dipper capacity, suspended hoist load, and peak hoist load. A ratio of conventional and concept dipper performance at the 1/20th scale was then evaluated to allow prediction of the performance of an ultra-class concept design using an independent ultra-class conventional dipper dataset. The outcome indicated a peak hoist requirement of 15.5% less to achieve the same production as the conventional design.

Jan 1, 2011

By L. M. Dwarkin

Introduction Avital factor in the success of any coal mining operation is the method of roof support employed. A coal seam in? place has been described as the filling in a geological sandwich and the process of mining as the art of snatching the filling from the midst of the sandwich. The difficulty of this task can be appreciated -in the realization of the tremendous weight bearing on a coal seam due to overlying strata; a weight that can exert pressures of several thousand pounds per square inch. Over the years that mining has been carried on, methods have been evolved by arduous trial and error, making possible the successful extraction of billions of tons of coal. However, these time-proven methods are not enough. The constant demand for faster and cheaper production, the necessity of mining under increasingly difficult conditions, and the requirement for higher standards of safety, call for ever better and more efficient roof support. A recent and very promising development in answer to this need is that of Roof Bolting. Roof Support in General Before proceeding to the subject proper, a brief discussion of the older roof support methods is of value in illuminating the difficulties involved and the problems to be solved.

Jan 1, 1951

By G. Reuben Yourt

THIS paper is chiefly a description of the improvements in dust control chat have been brought about in the assay office grinding room at Wright-Hargreaves. The fume exhaust systems are briefly included because they also are important to the health of the employees. There are three chief factors which determine the efficiency of a dust control system: First, the amount of time and thought spent in designing it. Second, how close! y it is kept up to date with the growth of the plant-a system that is adequate for the number of machines operating when it is installed may fall short of fulfilling its purpose as the plant expands. Third, unless someone is held directly responsible, a system is likely to get out of repair and gradually lose its efficiency-this can easily be detected by regular dust surveys. In designing the present system at Wright-Hargreaves, the object kept in mind was to reduce the dust concentration of all operations to a safe limit, chat is, well under 300 particles per cubic centimecer of air. By doing this, a condition would be attained chat would make it possible to discontinue the use of respirators, which at best are not very comfortable and do not remove all of the hazardous fine-dust particles.

Jan 1, 1941

By S. Bozorgi, K. Anders

"The automotive applications of heat treatable AlCu cast alloys are designed for performance at high temperature, which can be improved using specially alloying element as well as different heat treatment. In this research work an effect of alloying element such as Cu, Ni and heat treatment on microstructures and mechanical properties of AlCu alloy were investigated using optical microscope (LIMI), scanning electronic microscope (SEM) equipped with energy dispersive X-ray detection (EDS), Differential scanning calorimetry (DSC) and mechanical testing. It was found that during solidification most of the elements Cu, Mg and Ni segregated at the grain boundaries in the form of Al2CuMg or Al7Cu4Ni and a very small part of Cu and Ni element dissolved in the FCC-Al matrix. The latter is not completely reclaimable for strengthening mechanisms in FCC-Al matrix in its as-cast state. The results of mechanical test show that yield strength and ultimate tensile strength increases after heat treatment significantly compared with the as-cast state. Furthermore the mechanical properties at elevates temperature (240°C) is higher with higher Cu+Ni+Si containing alloys compared with the less Cu+Ni+Si containing alloy.INTRODUCTION Due to the high strength-to-weight ratio, high strength and ductility at room- and elevated temperature, AlCuSi cast alloys are widely applied in the automotive industries specially for producing cylinder head and engine block, where modified alloys with enhanced metallurgical properties are always needed to satisfy the ever increasing demands for the applications. The AlCu based cast alloys can be strengthened by age hardening. The precipitation processes from which this hardening is derived can be attributed to the presence of selected trace element additions or micro alloying, which can change the process or kinetics of precipitation in age hardenable AlCu cast alloys (Polmear, 1998; Morris, 1991). Furthermore their strength is mainly controlled by the aging process through the precipitation and growth of very fine precipitates of the ?'-phase (a semi-coherent, metastable form of the equilibrium Al2Cu phase) from the Al and Cu Guinier-Preston (GP) zones. Several studies have shown that solute clustering occurs prior to the precipitation of GP zones, and this modifies both the nature and kinetics of the precipitation process. The typical size of GP zones is in the order of tens of nanometers, and the chemical composition of these precipitates is not easily measured, even with a typically analytical electron microscope (Polmear, 1989)."

Jan 1, 2018

By J. J. Quinn

Several mineral flotation plants utilize process water with high soluble salt content. The processing of semi-soluble minerals, the use of recycle streams, sea or well water give rise to this situation. It is unclear as to the overall effect on flotation response though there does seem to be evidence of bubble size reduction, increased froth stability and reduced reagent dosage. The present work aims to quantify the effects of salts present in process water on gas dispersion (bubble size and gas holdup) and froth properties. The salts examined were NaCI, CaCl2, Na2SO4, Na2S2O3 and Al2(SO4)3. Tests were conducted to determine the effects of salt type and concentration on gas holdup and bubble size distribution. The salts containing multivalent ions had a greater impact than the monovalent ions, in keeping with the literature. A relationship between gas holdup and ionic strength was established. The concentration of frother (methyl isobutyl carbinol, MIBC) giving equivalent gas holdup was determined. The effect of salt and frother combinations was also explored.Proposed mechanisms for coalescence inhibition in salt solutions are briefly reviewed in light of the current findings.

Jan 1, 2006

By D. S. Salonine

Aluminum alloys are widely used in modern industry. Tubes and hollow shapes give great opportunities for structural purposes as well as fluid transport due to their stiffness and lightness, Extrusions on a mandrel or through a bridge die, that requires splitting of the billet with re-welding, produce hollow shapes with varied contours, fins and multiple cavities. Moving and stationary mandrels, mandrel lubrication, tooling for ribbed-tube heat exchangers, and for drilling pipes are considered. Bridge dies can be classified by the bridge position relative to the die face, by mandrel support structure, and by assembly type, The main parameters influencing the quality of the die-welded seams are considered, The difficulties of extruding various alloys through bridge dies are discussed in terms of metallurgical factors, Some approaches to the calculation of the stresses in a bridge are presented.

Jan 1, 2005

By R. Kumar, A. K. Verma

"In this paper, an anisotropic shear behavior of rock joints is investigated under constant normal load condition (CNL). The natural rock joint roughness is transferred to artificial rock samples using room temperature vulcanizing (RTV) silicon rubber. Artificial cylindrical rock joint samples (90 mm diameter and 50 mm height) are made by mixture of cement, sand, and water in the ratio of 1:1.5:0.45 (by weight). Direct shear tests are conducted on these samples in twelve directions at 30º apart at four different normal stresses (250kPa, 500kPa, 1000kPa, and 1500kPa). Thus, 48 samples are tested in laboratory. Test results shows that the peak shear strength (?) of rock joints is anisotropic in nature due to change in morphological features in particular shearing direction. Joint roughness coefficient (JRC) is determined in each shearing direction by trial and error method using Barton’s model (1973). Further, cohesion ( c) and angle of friction ( ? )of joint surface in each direction is determined. Finally, a relationship between angle of friction ( ? ) and joint roughness coefficient (JRC) is developed. Experimental shear strength and Barton’s shear strength is compared and it is found that effect of anisotropic decreases with increasing normal stress. INTRODUCTIONRock mass is generally composed of discontinuity which refers collectively to joints, faults, bedding plane and folds etc. ISRM (1978) defined joint as a line of break of geological origin along which there is no visible displacement. Joint is three dimensional discontinuity which composed of two matched/mismatched surfaces. The presence of joints in rock mass plays an important role to define its overall shear strength, deformability behavior, in-situ stresses and hydro-geological properties. The shear strength of rock joints is important in the design of near surface/ deep geotechnical works (mining excavation, dam foundation, power plants, underground caverns, and slopes).In last 40 years, many constitutive models are developed to predict shear strength of rock joints under CNL conditions (Patton 1966; Landanyi and Archambault 1969; Barton 1973; Goodman 1976; Barton and Choubey 1977; Plesha 1987; Desai ad Fishman 1991; Amadei and Saeb 1992; Maksimovic 1992; Wibowo et al. 1993; Huang et al. 1993; Amadei et al. 1998; Indraratna 2000; Homand et al. 2001; Wang et. al. 2003; Samadhiya et. al. 2008; Asadollahi and Tonon 2010; Ghazvinian et al. 2012). These constitutive models have limitations to predict shear strength of rock joints in one direction. Till date, among all constitutive models, Barton (1973) model is widely used in practice due its simplicity. It includes parameters such as joint roughness and joint compressive strength (JCS) to quantify joint surfaces."

Jan 1, 2015

By Ann Bigué

Outline of Presentation 1. Impacts and Benefits Agreements Defined 2. Elements that determine the content of an IBA: ? the nature of the project ? the identity of Aboriginal communities affected by the project ? the legal environment 3. Content of Impacts and Benefits Agreements Impacts and Benefits Agreements Defined Have emerged in response to effects of major mining projects located on or close to Aboriginal lands and close to Aboriginal communities Are negotiated between the mining project proponent and one or more Aboriginal groups May include government May be known under other names

May 1, 2004

In the flotation of a copper ore, entrainment of fine silicate and iron sulfide gangue minerals resulted in poor copper concentrate grade. In the cleaning stage, rejection of these gangue minerals was particularly difficult due to severe mechanical entrainment when the rougher concentrate was ground to 10 µm. To reduce gangue entrainment, polymeric depressants were tested. The rationale being that with the use of such polymeric depressants that also possess flocculation power, not only minerals-to-be-depressed can be made hydrophilic, but their particle size can also be enlarged. In this manner both the "genuine" flotation and the mechanical entrainment can be reduced. An effective polymer to reduce entrainment of silicate gangue mineral in sulfide flotation was identified from bench flotation tests conducted on single minerals. It was then applied to the flotation of a copper-gold ore confirming the beneficial role of the polymeric depressant in the reduction of fine gangue entrainment.

Jan 1, 2007

By S. Mohammadnejad, M. Olizadeh, B. Mehrabi

A new method using a combination of comprehensive mineralogical and analytical approach which includes optical and electrical microscopy and several analytical techniques with diagnostic leaching has been used to characterize the associations and distribution of gold in a variety of minerals from the Zarshuran refractory gold ore, NW Iran. Zarshuran ore with an average of 7.9 g/t Au-grade and about 8% arsenic with gold recovery less than 20% in direct cyanidation is considered as high arsenic, high au-grade refractory gold ore. In most of the refractory ores, gold is associated with arsenopyrite and co-para genetic ore minerals, while in Zarshuran ore; gold is associated with orpiment, realgar and arsenian-pyrite. Considering its mineralogy and As content, it can be considered as the most difficult refractory ore for characterization and processing. Results from the mineralogical examination and diagnostic leaches indicate that there is only a small amount of free gold (17-19%) that is present in cyanide-soluble sulfo-arsenides compounds, predominantly orpiment and realgar. Diagnostic leaches also indicate that little gold is occluded within the silicate structure (14%). Overall, the gold is mostly included in sulfides, arsenic sulfides and sulfo-arsenides (50%). The results also have shown how the technique can be used to gain a good initial understanding of potential metallurgical problems for a refractory gold ore.

Jan 1, 2005

By W. E. Armstrong

Gypsum was first exploited as ?a commercial proposition in this province by the Union Mining Company which, in 1900 opened quarries on the east shore of Lake Manitoba, near the present site of Gypsumville. This company established a mill at the head of Portage Bay on the lake, and the manufactured plaster was carried by the companies boats to McArthur's siding on the Whitemouth river near Westbourne, Man., from which point it was distributed. In 1904 a reorganization took place and the Manitoba Gypsum Company Limited bought out the original company, and operated the original mill for about one year when it was destroyed by fire. There were many factors which rendered the operation of a mill at the quarries very difficult; lack of rail transportation for bringing in supplies, and the impossibility of local power development made manufacturing costs very high. Satisfactory distribution could not be affected because of water transportation and poor terminal facilities at McArthur's siding. For these reasons the new mill was built at Winnipeg, where cheaper power and better distributing facilities permitted the industry being placed in a better position. The company continued to bring the gypsum rock by steamer to Totogan, from which point it was transported by rail to Winnipeg. This period was one of steady expansion as the product became better known and more universally accepted as a wall finishing material. Unfortunately, in 1909, this new mill was destroyed by fire, causing a serious set-back to the company, at a time when the steady growth of the western market gave every promise of the industry being placed on a profitable basis.

Jan 1, 1925

By C. F. Gleeson

"Geochemical stream-sediment reconnaissance can be a useful exploration tool from the point of view of rapidly and cheaply evaluating the mineral potential of an area. This is particularly true of rugged and mountainous areas such as are found in Gaspé. For the past two years, SOQUEM has been carrying out such surveys over favorable geological regions in the Appalachians of northern New Brunswick and Gaspe. To date, about 4,000 square miles of terrain has been systematically covered by reconnaissance geochemistry. Jeeps have been used as a means of transportation in the easily accessible areas and a helicopter equipped with a winch has been used to lower crews into the more difficult-to-reach regions. Such surveys have been successful in finding metallic mineralization which otherwise might not have been detected.Electronic computation of analytical information has been used to construct regional metal maps, rolling mean maps and residual metal maps. These maps have helped in evaluating anomalies, in relating the regional geo-chemistry to the regional geology and in comparing the distribution patterns of metals. To date, some 30,000 stream-sediment samples have been collected from the Gaspe region and analyzed for Cu, Pb, Zn and Mn. These analyses are being subjected to computer analysis."

Jan 1, 1969

By R. P. van Hille, N. Mooruth

Remediation of acid rock drainage (ARD) was performed within a linear flow channel reactor (LFCR) via a floating sulphur biofilm (FSB). A full sulphur species material balance was conducted in order to characterize the sulphide oxidation. The reactor was able to achieve an 82% and 93% conversion of sulphide with a hydraulic residence time of 2 and 5 days respectively. 92% and 55.5% of the converted sulphide reported to the biofilm as sulphur for the 2 and 5 day residence times respectively. The mass transport limitations within the biofilm were identified via a dissolved oxygen gradient profiling system.

Jan 1, 2011

By Maria D. Mastalerz, Wei Wang, Maria E. Holuszko, Amit Kumar

In this study, the micro-FTIR analysis was used to investigate in-situ surface properties of coal and its components (macerals) and these were directly correlated to the coal hydrophobicity as measured by the contact angle before and after reagent addition to understand the suitability of the reagent for flotation. The micro-FTIR technique can provide a semi-quantitative analysis of the chemical functional groups on coal surface, exactly where the contact angle is being measured. Selected functional groups and their ratios that provide information about aromaticity, the contribution of oxygenated groups, and aliphaticity are used to evaluate the reactivity between reagents and various coal components. The observations made in relation to the susceptibility of some reagents towards certain coal components should lead the way to a smarter way of using process design in terms of reagents selection for coal flotation.

Jan 1, 2017

Roasting of molybdenite concentrate is an important stage in the production of commercial molybdenum trioxide. The oxidation kinetic and mechanism of molybdenum sulfide concentrates from two plants were investigated at temperatures from 444 °C to 640°C. The rate of reaction was determined for thin layer samples in a muffle furnace at controlled temperatures, oxygen excess and removal of sulfur dioxide. For both concentrates the rate of reaction is fairly slow at temperatures below 500°C and remains fairly constant from 540 to 600 °C. It was observed that the concentrate from the first plant presents a tendency for sintering or glazing at temperatures above 620°C, whereas the same phenomena was observed at 20 or 30 °C higher temperature for the second concentrate. A kinetic model of two reactions, involving the formation of Mo02 as intermediate oxide for the production of Mo03 is proposed and activation energies of 23.0 and 20.8 kJ/mol for the first and second reaction were calculated for temperatures between 520 °C to 600 °C. These low values of activation energies indicate that the overall rate of oxidation is controlled by mass transfer, particularly in a porous layer of oxides. Therefore, the renewal of the surface by mixing and motion of the concentrate layer is of great importance. Sublimation of Mo03 becomes significant for temperatures above 650 °C.

Jan 1, 2007

By J. R. Kish, J. Dabrowski

"The susceptibility to intergranular corrosion modes is a major technical issue preventing widespread utilization of higher strength welded AA7xxx extruded beam profiles, in the peak-aged T6 condition, in automotive bumper assemblies. A study was undertaken to evaluate the relative exfoliation corrosion resistance (ASTM G85-A2) as a function of joint design parameters, namely the base alloy composition, heat-treated condition and beam orientation after exposure to a cyclic acidified salt spray test. This paper documents the major findings extracted from this study.INTRODUCTIONBumper systems play a predominant role in the passive safety of an automobile, since they are one of the main structures for absorbing the collision energy in the event of an automobile crash. Heattreatable AA6xxx-series (Al-Mg-Si) and AA7xxx-series (Al-Zn-Mg) Al alloys, with relatively high strength, toughness, energy absorption, weldability and formability, make it possible to design costcompetitive bumper systems to crush in a controlled fashion. In this context, Cu-lean AA7xxx extrusions, such as AA7003 and AA7108, which exhibit higher strength than AA6xxx extrusion, such as AA6082, represent an attractive light weight material from which to fabricate bumper assemblies (Clausen et al., 2000; Pedersen et al., 2008; Chen et al., 2009).Arc welding is a key joining process for AA7xxx alloys within the transportation industry. A major technological issue preventing widespread utilization of arc-welded AA7xxx joints is the susceptibility to severe localized corrosion (Kent, 1970, Reboul et al., 1985; Holroyd et al., 1987). It generally occurs as exfoliation corrosion within a heat affected zone (HAZ) a few millimeters from the weld bead, or a type of stress corrosion cracking (weld-toe cracking), which initiates at the weld toe and propagates into the interfacial region between the weld bead and the HAZ (so called “white zone”). In addition to the micro-galvanic cell activity induced by the intermetallic compound constituent and strengthening particles present, there is strong evidence that macro-galvanic cell activity between the weld bead and base AA7xxx alloy may be playing a controlling role. Electrochemical profiles taken across fusion welded joints, in cross-section, during exposure to saline solutions suggest that a significant potential difference exists across the AA7xxx arc-welded joint (Shumaker et al., 1967; Grauer and Wiedmer, 1980; Tuck, 1985, Onoro and Ranninger, 1993). These studies consistently show that the HAZ and base alloy are more electronegative with respect to the weld bead (arc-welded with AA5xxx filler wire). Despite this initial important work, the majority of the recent corrosion research effort on welded AA7xxx alloys has focused on the performance of friction stir welds (Lumsden et al., 1999; Wadeson et al., 2006; Hatamleh et al., 2009)."

Jan 1, 2012

By Qing-hua Tian, Li-then Cheng, Xue-yi Guo

In order to recycle valuable metals from silver separated residue, a novel method using alkaline smelting at low temperature was proposed. The main factors affecting the main metal recovery such as the smelting temperature, smelting time, liquid-to-solid ratio and alkali addition were investigated comprehensively. The behavior of the main metal elements, such as Pb, Sn, Sb and Bi in silver separated residue was also discussed. The results indicated that amphoteric metals such as Pb and Sn can be smelted into the melt, while other metal elements, such as Sb and Bi were left in the residue.

Jan 1, 2011