Search Documents

By Marcel M. Djivre

Electromagnetic wire rope testing is the only practical non-destructive method to evaluate the current condition of wire ropes in general, and in the mining industry in particular. The method has been successfully used worldwide for decades. In mining it has considerably improved the safety of operations. Yet, problems persist. In particular both the Loss-of-Metallic-Area (LMA) readings, as well as the Local Fault (LF) readings, as obtained by different instrument operators, were found to be unacceptably diverse. Consequently, large sums have been spent internationally, as well as in Canada, comparing a whole range of these instruments in an effort to rate their performance. The published results clearly confirmed operational experience, namely that the LMA and LF readings were, indeed, unacceptably diverse. Excellent pertinent conclusions were also published. In Canada the authors? conclusion was that while the divergence in the LF signal based results could, possibly, be attributed to both hardware and human-error related factors, the LMA signal related quantitative uncertainties were human-error related. Consequently, much attention was paid in Canada to developing novel control methods, namely computerized ones to replace the more error-prone analogue ones. In addition new sensor-heads were developed, both for portable as well as for permanent installation with remote control operations. While these efforts were of considerable benefit, the situation must again be carefully reviewed with very special reference to deep-level mining, now of immediate concern in Canada as well. In this paper the authors supply an overview of the results obtained by three of the four major international projects referred to previously. Relevant conclusions/comments are also restated. Moreover, specific recommendations are put forward as to how current problems might best be remedied.

May 1, 2004

By C. Pelley, S. Kelebek, G. Kunzel, S. Gregersen, M. Pollanen

A series of small-scale tests was conducted to evaluate the effect of micro-fracture development, imposed by blasting, on the material properties of the rock as well as its resistance to crushing and grinding. The uniaxial compressive strength, tensile strength, Poisson’s ratio, Pwave, S-wave velocity, point load test index, crushing, and grinding work indices were evaluated for samples without any blasting load and for samples which had received a variety of blast loads ranging from a single impact with a lowstrength detonating cord to a combination of impacts at different times and significant impacts with powder factors close to those used in practical blasts. It was shown that the rock mechanics parameters change even at low impacts, suggesting easier crushing of the rock. Damage values appear to be affected by timing as stress wave superposition affects the damage process. Fragmentation is achieved at higher impact levels while work index modification of the fragments is also observed when high powder factors are used, suggesting improvements in grinding.

Jan 1, 2006

By P. V. Golde, R. A. Poole, G. R. Baiden

"INCO is committed to proceed into the next century using automation and robotics to achieve safety and productivity goals necessary to enhance its competitive position. Stobie Mine, decades old, is the first of its mines to change from labour-intensive to automationassisted techniques. This paper is a synopsis of the progress made during the transition period including overviews of some of the projects as well as some of the difficulties in the assimilation of the technology. BackgroundThe ObjectiveThis paper is an update on remote control and LHD automation installation at Stobie mine. The communications system installed at the mine and the ability to remotely control underground equipment from surface is reviewed (Poole et al., 1996, 1997). It discusses some of the experiences and processes required to further the concept to consolidate the operation of multiple machines under a single operator. It considers the communications systems requirements and their focuses, particularly on the development of systems for the tele-operation of LHDs and drilling machines from surface."

Jan 1, 1998

By Jan E. Nesset, Julie Fournier, Jorge Torrealba, Colin Hardie

"Gas dispersion studies have been used to benchmark and optimize plant flotation performance for more than a decade, although this technology is not as widely in use as it likely should be based on the significant improvements that have been reported. Part of the reason may be a general lack of awareness within the industry of just what these improvements have been. This paper reviews a number of the reported case studies, groups them into categories of improvement, and draws some general conclusions. The paper will be of interest to plant engineers and technology providers seeking new approaches and tools for improving their own and clients’ processes.INTRODUCTIONThe sector of flotation hydrodynamics that is now known as gas dispersion technology, and the corresponding terminology, had its beginnings in the 1980’s and early 1990’s in the laboratories of McGill University where the students of Prof. J.A. Finch and Dr. C. Gomez conducted studies of gas holdup, superficial gas rate and water recovery on laboratory flotation columns (Laplante et al., 1983; Xu et al., 1991;, Banisi and Finch, 1994; Finch et al., 1999; Nesset, 2011). Sensors were developed for gas holdup (eg), gas rate (Jg) and bubble size (Db) distribution (Tavera et al., 1996: Finch et al., 1999; Dahlke et al., 2001; Chen at al., 2001; Hernandez-Aguilar et al, 2002, 2005). The sensor measurements were rapidly adapted for use in mechanical flotation machines in plant environments (Gomez and Finch, 2002; Gomez et al., 2003; Cooper et al, 2004; Torrealba-Vargas et al, 2004; Nesset et al., 2007). Somewhat parallel developments were being conducted by Gorain and colleagues at the University of Queensland’s JKMRC on pilot and industrial flotation machines using the McGill approach but utilizing alternate sensor designs for eg, Jg and Db (Gorain et al., 1997, 1999; Schwarz and Alexander, 2006) to link flotation kinetics to bubble surface area flux (Sb). Early industrial applications were those led by the university teams from McGill (Canada), the JKMRC (Australia) and the University of Santa Maria (Chile) at plants in North and South America, Australia, South Africa, Asia and Europe. Industrial organizations that brought the technology on-board in the early 2000’s included Teck Resources (then Teck Cominco), COREM, Vale (then Inco), Anglo American Platinum. Several of the major flotation cell manufacturers also purchased the McGill bubble viewer technology for their own equipment studies. The sensors have continued to evolve with multiple and continuous measurement of Jg (Torrealba-Vargas and Finch, 2006, Bartolacci et al., 2008), gas holdup by acoustic means (O’Keefe, 2007) and a combined Jg-Db device called the Anglo Bubble Sizer (Harbort and Schwarz, 2010). A review of the gas dispersion technology use and development have been provided by Gomez and Finch (2002), Harbort and Schwarz (2010) and Nesset (2010)."

Jan 1, 2015

By David Seaman, J-P Franzidis, Emmy Manlapig

"A new device has been developed to directly measure the bubble loading of particle-bubble aggregates in industrial flotation machines, both mechanical flotation cells as well as flotation column cells. The bubble loading of aggregates allows for in-depth analysis of the operating performance of a flotation machine in terms of both pulp/collection zone and froth zone performance. This paper presents the methodology along with an example showing the excellent reproducibility of the device and an analysis of different operating conditions of the device itself.The device has been used to investigate the froth selectivity of attached particles. Simultaneous measurements were made using a different froth recovery measurement technique in the same flotation cell. A comparison of these techniques shows that in this case, particles are selectively detached from bubbles at or near the pulp-froth interface.INTRODUCTIONA flotation cell can be considered to operate in two distinct phases or zones; namely the pulp or collection phase and the froth phase. The pulp zone is responsible for the formation of hydrophobic particle-bubble aggregates, whilst the froth phase is responsible for the separation of these aggregates from surrounding suspended hydrophobic and hydrophilic particles. Thus, the froth phase is the grade determining phase in flotation. A measurement of the bubble load (the mass of particles attached to air bubbles in units of mass/volume) will enable the analysis of the performance of both the collection zone at creating bubble-particle aggregates and also the froth zone at separating these aggregates from surrounding pulp.A measure of froth zone performance that has been used extensively in flotation research is the Froth Recovery, Rf, of a particular system. Froth recovery is defined as the mass of particles collected in the concentrate launder by true flotation as a fraction of the mass of particles entering the froth phase. The measurement of bubble load allows for this term to be calculated easily, rather than having to go through the laborious task of, for example, changing froth depths to determine this performance criterion (Contini et al., 1988; Vera et al., 1999b; Feteris et al., 1987)."

Jan 1, 2004

By F. A. McLean

The past decade has witnessed a rapid increase in the number and variety of uses found for internal combustion engines in mining operations. Gasoline engines are now widely used for operating core drills, pumps, compressors, small hoists, switching locomotives, tractors, boats, and other equipment. The heavy-oil engine is employed for operating compressors, generators, shovels, ore-milling machinery, and- in the iron, copper, and coal districts- in connection with that' latest newcomer in modern railroading, the oil-electric locomotive. Each of these applications could well form a subject for a lengthy treatise in itself. This paper, however, will be confined to a discussion of some of the features of internal combustion engines as applied to mine compressing plants and mill drive. Perhaps at no time in the history of mining in Canada has the search for new mines been more vigorously carried on, more old properties rejuvenated, or more remote districts exploited than during the past three years. The mine operator of today has a far wider range of equipment and facilities at his disposal than had the pioneers of Rossland, Cobalt, or Porcupine. Each year now witnesses the hinterland driven farther and farther back as improved forms of transportation, machinery, and methods make possible the exploration of properties once considered too inaccessible to warrant serious attention. Howey, Sherritt-Gordon, Callinan-Flin Flon, Jackson-Manion, Picard Gold Mines, and a number of properties in British Columbia, afford excellent examples of work carried out on an extensive scale miles from a railway, or in comparatively inaccessible mountain regions.

Jan 1, 1928

By Craig M. Sams

"Variable speed mill popularity has grown during the last 10 years with almost every SAG mill fitted with a variable speed drive. In addition, many of today’s larger ball mills are running a variable speed drive for various reasons. In the past, motor suppliers, especially gearless drive suppliers, have considered mills as being an overpriced rotor. This has lead to mills demanding more torque than what a motor can generate. This paper identifies the reasoning of what has happened and how to mitigate the mismatch in the future. Technical and economical issues are discussed, allowing mill operators to make an informed decision of which path to take in deciding what motor to put on a mill.INTRODUCTIONIt has been generally accepted in the past that motor suppliers and specialists in engineering companies understand the workings of a SAG mill or a ball mill and although there is a fair knowledge within the industry, in regards to mill torque requirements, the advent of variable speed drives in ball mills has shown the writer that a complete understanding of the mill torque requirements are not fully understood.This paper will discuss two aspects of mill torque requirements, (operating torque at various charge levels and start up torque), and how it relates to specifying the proper motor torque requirements.MILL OPERATING TORQUEMill operating torque at a given charge level and density in a mill is essentially constant throughout the entire speed range. For the purpose of this paper, we will take a 38’x 22.5’, 20’ EGL, SAG mill and provide the power draw at variable speeds but fixed loading conditions.The power draw and mill torque of this mill at 8% ball charge and 28% total loading (Highlighted) is shown below as Figure 1, at variable speeds."

Jan 1, 2007

By M. J. Fairweather, Keith Lee, Naseem Mian

"The initial metallurgical response of the lead flotation circuit at Cominco Alaska's Red Dog Mine was substantially below feasibility expectations. A program of diagnostic mineralogical analysis pointed the way to a number of process improvements, including simplification of the flow sheet and installation of a large flotation column as a lead cleaner. A diagnostic mineralogical analysis of the improved circuit shows that inadvertent activation of both sphalerite and pyrite has been substantially reduced, resulting in significant improvements in metallurgical performance. Directions for further improvements to the circuit performance are suggested by the recent analysis.IntroductionRed Dog is a high-grade, sedimentary exhalative (sedex) deposit with relatively simple mineralogy. The primary non-sulphide gangue minerals are quartz and barite, with minor barium carbonate (witherite). The iron sulphate minerals, siderotil, rosenite and copiapite occur variably throughout the deposit. Mineral texture is variable ranging from liberated sphalerite grains visible to the naked eye to intergrowths, particularly between sphalerite and galena, to less than ten microns. Both pyrite and marcasite are present. To date no enhanced reactivity of marcasite has been observed. For this discussion, ""pyrite"" will be used to refer to both iron sulphide minerals. In common with other sedex deposits, Red Dog contains organic and sulphur impurities."

Jan 1, 1997

By Ray Walton, Ron Colquhoun, Ken Thomas, Dwayne Fentie, Barney Burke

"The new Roasting Facility at Barrick’s Goldstrike Mine in Nevada, U.S.A. was developed to process 12,000 tons per day of refractory gold ore. The process consists of crushing, dry grinding, roasting, extensive gas purification, calcine quenching and leaching in the presence of activated carbon. The new plant is integrated into the existing Goldstrike facility, treating ore from both open pit and underground sources.The process design, procurement, construction and commissioning of the Roaster facility was performed successfully over a 3% year period with peaks of 400 engineering personnel and 950 construction personnel supporting the project. The US$330,000,000 project was completed ahead of schedule and under budget. The commissioning was well planned and proceeded smoothly through a rapid start-up to achieve all primary goals within three months of the start of processing of ore.BACKGROUNDAs early as 1992, Barrick’s Goldstrike Mine, located north of Carlin, Nevada had indications of the ore becoming ever increasingly carbonaceous in nature. As the open pit and underground exploration programs proceeded to step out over the years that followed, the accumulative amount of carbonaceous refractory ore and tons had become significant. By 1997, 29 million tons of double refractory carbonaceous ore containing an estimated 11.6 million ounces of gold had been identified. By 2000 the resource had increased to 14.3 million ounces."

Jan 1, 2001

By Q. H. Bui

The elastoplastic self-consistent model is one of the effective models to study the initial microstructure effect on the mechanical behavior of bulk materials. However, the use of this micromechanics-based model which takes into account only the Hall-Petch relationship at grain level for predicting the grain sized effects on the strength of the deformed materials is not accurate yet because of the fact that the dislocation density contributes also to the strengthening of this kind of materials. In this study, a modification made to the Hill-Hutchinson elastoplastic self-consistent model was proposed for investigating the microstructure dependence of the mechanical behavior of cold-drawn 6063 aluminium tubes. Because of the novel modification, an estimation procedure with two steps was required to identify the parameters of this micromechanical model. An acceptable agreement between experimental and theoretical stress-strain curves was achieved.

Jan 1, 2011

By J. Zhang, T. Oleniuk

It is well-known that Saskatchewan has the world’s richest uranium deposits and advanced processing technologies. Unlike the Saskatchewan deposits, complicated mineralogy is common for other places in the world. Mineralogy dictates the process. Mineral Processing at the Saskatchewan Research Council has been working with the uranium industry worldwide since its inception to develop effective processing technologies to suit the unique mineralogy of each deposit. This paper reviews the research and development of uranium processing technologies in the current major uranium production areas such as Canada, as well as the potential development regions like Argentina and Sweden. Acidic and alkaline leaching processes, as well as by-product recovery technologies are discussed based on mineralogy.

Jan 1, 2020

By N. Behnood

"This paper describes how material selection, quality assurance, and failure investigation play important roles in the efficiency and safety of mining and metallurgical operations.INTRODUCTION Material selection, quality assurance, and failure investigation are all complementary elements of materials engineering in the application of materials technology for failure prevention. Based on commodity price increase of 300% between 2002 to 2013 [1] and increased cost ofcapital projects and operation, equipment failure, which in some cases causes complete shutdown of the operation, becomes a vital importance in mining and metallurgical plants. The following sections present a number of examples from many failure cases experienced by the author during his three decades of work as a materials engineer in the mining industry."

Jan 1, 2015

By Anton Gronningsater

AT the present time we hear a great deal about organization of labour, collective bargaining, workmen's councils, and company unions; about C.1.0. with its principle of vertical unions and A.F.L., largely based on craft unions; and about provincial and federal laws for protection of labour's right to collective bargaining. What we perhaps hear too little about is corresponding organization of the employers, although it recently is mentioned more frequently. I will only mention W. H. Davis, Chairman of the United States War Labour Board, who has had and is having plenty of experience in this field and has also studied labour conditions in Europe-in Sweden for instance. He has repeatedly expressed the opinion that where employer-employee problems are involved, a thing badly needed in America is organization of employers as well as employees to get some order in the present chaos. With this I agree. I believe a strong organization on one side necessitates a correspondingly strong organization on the other side; that has at least been the experience in the industrialized countries in Europe. I happen to be fairly familiar with conditions in Norway, where they have struggled with these problems for fifty years, and a talk on the history, development, and present state of employer-employee relations in that country might perhaps be of interest as giving a general picture of the development of such relations in the northwestern European countries as a whole. The talk was originally given to the Fourth Year students in Mining and Metallurgy at the University of Toronto. I have changed it somewhat to fit a different audience, but I hope you will make allowances if you now and then are reminded of the school auditorium. I will try to be as objective and factual as possible, but it is probably unavoidable that some of what is said is coloured by personal opinion.

Jan 1, 1943

By P. J. Mehrfert

"Recovery of mineralized coarse particles is notoriously low in conventional concentrators that treat copper porphyry ores. The application of coarse particle flotation techniques has the potential to achieve comparable metallurgical performance at significantly coarser primary grind sizings. ALS Metallurgy has been conducting both internal research and commercial test programs to investigate the potential of Eriez HydroFloatTM technology on copper sulphide ores. Test data indicates that significant improvements in the recovery of copper sulphide bearing particles between 200µm to 850µm can be achieved using Hydrofloat technology compared to conventional flotation techniques. This paper summarizes the results from a selection of test programs that includes recovery by size data from both conventional flotation and HydroFloatTM tests. An explanation of the apparatus and test procedure will be given. Mineralogical analyses of the test products and characteristics that limit metallurgical performance will be discussed.Description of Apparatus and Test ProtocolThe HydroFloatTM laboratory cell is a clear plastic column with an internal diameter of 14 cm. Water and air are introduced to the cell through a circular manifold located in the lower portion of the cell. The cell has a conical bottom which directs slurry to a pinch valve that controls the discharge of tailings. Feed solids are introduced to the upper portion of the cell in slurry form. The cell is operated in a manner such that the manifold water creates a teeter bed zone of suspended solids in the middle portion of the cell. Tailings exit the bottom of the cell at a high pulp density, and most of the introduced water overflows the top of the column and is collected in a launder. Particles with a hydrophobic surface may attach to air bubbles that percolate through the teeter bed, rendering them sufficiently buoyant to be transported to the overflow launder.Three significant features of this arrangement enhance the potential to recover coarse, low grade particles by flotation techniques. Firstly, the hindered settling conditions created by the rising column of water allow coarse particles to become buoyant once attached to a modest sized air bubble. Secondly, the flow conditions within the cell are relatively quiescent compared to a conventional flotation cell that utilizes an agitator. This allows particles that have limited hydrophobic portions of their surface, due to a low content of exposed sulphide mineral, to maintain a somewhat fragile attachment to air bubbles long enough for successful recovery to the overflow. Finally, the absence of a froth phase at the top of the cell allows particles attached to air bubbles to immediately exit the vessel, reducing the potential to drop back into the pulp phase as bubbles burst or coalesce."

Jan 1, 2017

By E. L. Martheleur

The use of electricity in coal mines dates almost from the time when it was realized chat it could be used to produce mechanical power. The first motor put in service underground was installed to drive a small pump nearly 40 years ago, and since then the use of electricity in mines has reached an extent undreamed of at that time. We now find its universal adoption in all the mining countries of the world. Great progress has been made in the development of mining electrical apparatus in the last decade, and excellent and adequate material is now available for the use of electricity underground. Although mining accidents, due to the use of electricity, are not frequent, the miner is justified in demanding chat all electrical apparatus for installation below ground be constructed with a greater degree of safety than that used on the surface. That this view is shared by the authorities of the different mining countries is evidenced by governmental regulations relative to the use, erection, and maintenance of electrical apparatus below ground. Those with which we are specially concerned are the regulations for the installation and use of electricity in the coal mines of Nova Scotia. The potential dangers of electricity in coal mines are: Shock or burns by contact from live parts. Shock or burns by contact with parts which, although normally dead, have become accidentally alive. Fire. Explosion of gas or coal-dust Explosion of apparatus.

Jan 1, 1928

By A. Roca, G. Ríos, I. Ruíz, M. Cruells

Flash Smelting Furnace (FSF) hot dust-laden is cooled in a waste heat boiler (WHB) and then dedusted in electrostatic precipitators (ESP’s) before being treated, together with the Peirce Smith Converters off-gases, in the sulfuric acid plants for SO2 removal. FSF dust is sulfated by SO2 and O2 in the WHB. Typically, 70% of the dust from the FSF drops in the WHB while the remainder is caught in the ESPs. The collected dust is recycled to the FSF for Cu recovery. Some smelters have developed hydrometallurgical treatments to recover Cu from the dust; impurities, such as As and Bi, are bled as leach plant residues. This paper presents a study (laboratory scale), of leaching the FSF dust, generated in Atlantic Copper Smelter using the weak acid bleed from the gas scrubbing/cooling section (GSCS) of sulfuric acid plants. Leaching was performed with 0.5 mol L-1 sulfuric acid concentration, 60ºC, and a solid/liquid ratio 1/3. After leaching, H2O2 was used for arsenic and iron oxidation. pH was adjusted for precipitation of arsenic and iron as scorodite or as scorodite and arsenical jarosite. The precipitation was carried out at 95ºC during 3-6 h. Liquids after precipitation are suitable for subsequent treatments of electrolysis. INTRODUCTION The copper smelter dusts are usually recirculated totally or partially to the flash furnace. This practice increases the amount of impurities feeding the furnace. Some authors have developed processes for treatment of these materials for copper and zinc recovery and for arsenic, antimony and bismuth inertization. The processes for the treatment of copper smelter dusts can be pyrometallurgical (Yu, 1987; Carter, Vance, Aldridge, Zaw, & Khoe, 1994; Fu, Jiang &Wang, 2000), hydrometallurgical, or mixed processes (Yin et al, 1992; Mulale, Mwema, & Mashala, 1999; Gorai, Jana, & Khan, 2002). Hydrometallurgical processes have been extensively studied and, in some cases, applied to an industrial scale. The most important chemical reagent proposed for leaching the dusts has been sulfuric acid (Roman-Moguel, Plascencia, Pérez, & Garcia, 1995; Gabb, & Evans, 1997; Larouche, 2001; Morales, Cruells, Roca, & Bergó, 2010; Cáceres, Cruells, Morales, & Roca, 2012; Ecometales, 2013; Yang, Fu, Liu, Chen, & Zhang, 2017). Processes developed in alkaline media, and in some cases with the presence of sulfide, have also been carried out (Gabler, & Jones, 1988; Morales, Hevia, & Cifuentes, 2009; Alguacil, Garcia-Diaz, Lopez, Rodriguez, & Alonso, 2013), as well as by using a bioleaching process (Massinaie, Oliazadeh, & Seyed Bagheri, 2006; Bakhtiari, Atashi, Zivdar, Seyedbagheri, & Fazaelipoor, 2011).

Jan 1, 2019

By R. J. Hundermark, K. van der Merwe, L. R. Nelson

Taphole integrity is critical to all furnaces, but it is especially important in high intensity electric furnaces processing matte and metal of high superheat. Key furnace dimensions are the electrode proximity to the taphole, hearth sump below the taphole and the shape and location of the taphole in the furnace wall (e.g., circular versus rectangular furnace). In addition, electric furnace power density needs to be matched appropriately to any configuration to achieve operational reliability and furnace integrity. The role of furnace dimensioning is generically reviewed across many pyrometallurgical processes to explore potential impact on furnace taphole performance. Some empirical furnace dimensions and power density ratios of industrial furnaces are then compared to explore to what extent they may indeed influence taphole integrity.

Jan 1, 2015

By C. Gerow

THIS paper is entitled "Some" problems, rather than "The" problems, met in selling coal, since the problems to be met in selling any commodity have to deal with an infinite number of circumstances and conditions. These are believed to be more varied in the case of coal than probably any other commodity. This is due, perhaps, to the fact that coal has been one of the basic materials in the guiding of industrial and national achievement for the past two hundred years. During this time its use has developed from a most haphazard one to uses involving all modern scientific methods, which, rather than simplifying matters as regards the marketing of coal, have added many fresh problems, and these vary according to the particular market served. Since the concern of this paper is primarily the selling of Nova Scotia coal, it is proposed to deal chiefly with some of the specific conditions met in the markets presently served by this coal. For the purpose of discussion, these markets may be considered as divided into three main groups, namely, the Maritime market, the Quebec market, and the Ontario market. THE MARITIME MARKET First of all, let us consider the Maritime market. This is a market which has been regularly served by Nova Scotia coal since coal mining became the first industry in Cape Breton, slightly over one hundred years ago. Conditions as applying to the use of coal have naturally tended to adjust themselves to the characteristics of the coal most readily available, and, therefore, marketing problems are fewer in the Maritimes than in districts where many coals of varied characteristics are offered. Up to recent years, the problems involved were chiefly those of providing satisfactory service insofar as de-liveries were concerned. However, with the speeding-up of manufacturing processes and the necessity of reducing costs to a minimum, users of coal have become interested in obtaining coal that will give the most economical service. It is, therefore, now of importance that the salesman should have full knowledge of the particular conditions applicable to each customer's use in order to deal to the best advantage.

Jan 1, 1936

By P. S. Capper

"Generally speaking, the most intensive efforts at dust control in the mining industry have, in the past, been concerned with underground operations and where uranium ore or high silica material is processed. In the past several years, Stoop Rock has made Intensive efforts to reduce dust levels in it's Iron ore pelletizing complex. There have been no great engineering break-throughs with regard to dust control in such plants, and certainly no new engineering techniques have had to be applied at Steep Rock. This paper deals with how significant improvements in dust levels have been achieved through minor modification to dust collectors and ventilation units, improvements in operating practices, and education of supervisors and hourly personnel.PROCESS DESCRIPTIONSteep Rock Iron Mines is located 120 miles west of Thunder Bay near Atikokan. (fig. 1) Run-of-mine ore is pelletized along with some -1"" concentrate that has been processed in the concentrator (a summer operation only), which utilizes gravity separation to upgrade a mechanical mixture of ore and waste."

Jan 1, 1976

By J. Chlopas, D. J. Barratt, M. V. Sharp

"This paper describes the modifications made to the Fox Mine copper concentrate bin in order to obtain a continuous flow condition. The design of these modifications is based on test results obtained on Fox Mine concentrate using the flow factor testing machine in the research facilities of Cominco at Trail, B.C.The original design consisted of a cylindrical steel bin on a concrete slab with two slot-discharge openings. Based on predictions of the maximum mass flow hopper angle for conical and wedge shaped hoppers for the concentrate on various potential bin lining materials, Ultra-High Molecular Weight (UHMW) Polymer was selected as a liner.Using the recommended angles for conical and wedge shaped hoppers, the profile of the bin base was changed to suit the existing slot openings.The initial method of fastening the liner resulted in failure of the connections. Subsequent modification to the zinc concentrate bin fastener system proved satisfactory and it has now been in operation for over one year without any separation of the lining material.Utilization of flow testing procedures on concentrate samples has demonstrated that proper design of storage bins or hoppers to achieve continuous flow can be incorporated into the design of new plants."

Jan 1, 1978