Search Documents

By M. Hajian Heidary

In this investigation, effect of pressure depth on the globulizations of AZ91 magnesium alloy was studied. Cylindrical samples of AZ91 alloy with 1 cm and 2cm in height and 2.5cm in diameter (H/D = 0.4 and 0.8) were prepared, then the samples were hot pressed at 10 and 30% strain at a constant temperature of 200°C; subsequently reheated at 555°C in different times. Results obtained from optical microscopy (OM) showed that the thickness of the samples and consequently, depth of strain affected regions have remarkable effect on the degree of globulization. In addition, it was found that at a constant strain and holding time, structure of thinner samples is more globular than thicker ones.

Jan 1, 2007

By L. G. Smith, C. A. Shook, W. H. W. Husband, W. Schriek

"The flow of slurries in pipelines is governed by many variables, and the study of the influence of each of these variables is difficult, if not impossible, in some cases. Many correlations are available which fit data within a given range. However, no one method is yet available to design a slurry pipeline for all desired conditions without at least some physical measurements on the slurry itself. For this reason, the slurry pipeline facilities at the Saskatchewan Research Council have been developed during the past 12 years and it is hoped that the development will continue until the process is thoroughly understood and test facilities are no longer necessary. This paper outlines methods currently used and under development at the Saskatchewan Research Council for measurement, control and study of the variables governing the flow of slurries."

Jan 1, 1973

By W. A. Kracht

The McGill Bubble Size Analyzer, with the original image-capturing device (digital video camera), has a proven record for measuring bubble size distributions that are relatively narrow, such as in mechanical cells with frother. However, some problems arise when dealing with bubble size distributions characterized by a bi-modal shape and wide range of sizes such as found in some flotation columns. To measure wide bubble size distributions it is necessary to increase both the resolution to image the small bubbles and the viewing area to include the large bubbles. This can be done using a digital still camera: digital still cameras can have higher resolution than the digital video cameras currently used and with the proper lens the viewing area may be increased without resolution loss. The digital still camera approach was used to measure bubble size distributions in flotation columns at different operations in Chile. A comparison with typical bubble size distributions generated with mechanical cells is presented.

Jan 1, 2007

By James Stenhouse

Abstract The aqueous oxidation of pyrite in caustic solutions under oxygen pressure was investigated by measuring that effect of reaction variable on oxygen consumption by the reactions. From the results of this investigation, a model for the process has been proposed. In this model, sulphur diffuses as a positive ion through an oxide layer which forms on the sulphide particles and is then oxidized to sulphate ion. Iron is oxidized by substitutional diffusion of oxygen atoms into the oxide layer. The effect of most reaction variables on the rate of oxygen consumption can be explained with this model. Introduction Recent investigations (1,2,3) have shown that certain sulphide ores can be readily leached by agitating the ore in the form of a pulp under pressure in the presence of oxygen. Since very little was known of the mechanism of this oxidation, a programme of investigation was inaugurated in 1949 in the laboratories of the Department of Mining and Metallurgy of the University of British Columbia. Financial support for the investigation was received from the National Research Council in the form of student grants and bursaries, from the Canadian Liquid Air Company, Limited, and from the Consolidated Mining and Smelting Company of Canada, Limited. The first objective was to devise a technique to study the primary oxidation reactions in aqueous solutions and to apply the technique to a detailed study of the oxidation of pyrite in caustic solutions.

Jan 1, 1952

The reliability of mining systems is generally low due to their harsh working conditions. Currently, efforts for improving mining system reliability are often made in isolation. This practice could substantially limit the effectiveness of the efforts on overall reliability improvement of the mining system. To enhance the overall reliability of mining systems, an integrated improvement approach is necessary. In this paper, we developed a framework for integrated mining system reliability improvement to address this issue. In this framework, there are five major components including data integration, business process integration, hardware integration, software integration, and analysis/decision integration, but we only focus on the integrated reliability analysis which is important to the analysis/decision integration. The reliability analysis considers the interactions between machines, and the impacts of design, operation, maintenance, automation and working environment on the overall system reliability. These multiple interactions present a big challenge to accurate reliability prediction. In this paper, we for the first time systematically investigated integrated reliability analysis approaches for dealing with this challenge using novel models and methods, including covariate hazard models, intelligent reliability prediction approach, and complex system modeling methods. While these models and methods have found some successful applications in other industries, they in general have not been effectively used for the reliability analysis of mining systems. Our study results show that the system integration approach is applicable to mining systems and can be used for developing a computer aided integration system for the implementation of the integrated reliability improvement approach.

Aug 1, 2013

By Wei Huang, Anh V. Nguyen

"Potash flotation is an industrially proven success of flotation of soluble salts, but its collector adsorption mechanism remains elusive. In this paper, specific ion effects in NaCl-KCl flotation with carboxylate collectors were investigated. Flotation recovery and contact angle were determined as a function of brine composition of NaCl and KCl. The experimental results have shown that wettability of KCl and flotation of the soluble salts with laurate collectors were dependent on brine ion composition. Specifically, adding Na+ to brines decreased hydrophobicity of KCl crystals and their flotation recovery. Both KCl and NaCl could be floated with laurate collectors. However, flotation of NaCl was greatly enhanced by adding K+ to brine whereas flotation of KCl was significantly suppressed by the presence of Na ions. The decrease in KCl recovery upon adding Na+ is attributed to the counter-ion binding in the pulp. The flotation recovery enhancement of NaCl in the presence of K+ is explained by two effects: 1) increasing K+ concentration leads to a better dispersion of collector colloids in the pulp and 2) K+ enhances the collector adsorption at NaCl crystal surfaces. The water affinity matching rule can explain the specific ion binding behaviors and supported by the SFG spectroscopic results.INTRODUCTIONPotassium is an important fertilizer. Its primary source comes from potash ores, which are a mixture of sylvite (KCl), halite (NaCl) and many other complex double salts such as carnallite (KCl·MgCl·6H2O), alkali nitrates such as KNO3 and NaNO3, and sulfates-langbeinite (2MgSO4·K2SO4) with water-insoluble minerals such as clay and carbonate minerals. Previously, these salts were recovered with a lengthy hot leaching method, with further crystallization of potassium salts from saturated saline solutions. Selective flotation has been preferred since 1940s. Various collector adsorption mechanisms have been proposed soon after the industrial introduction of potash flotation. These include the formation of the insoluble compound model (Halbich, 1933; Singewald, 1961), an ion exchange model (Fuerstenau and Fuerstenau, 1956), a heat of solution model (Rogers, 1957), the surface hydration model (Schubert, 1988), the surface charge model (Roman, 1966; Miller et al., 1992), the interfacial water structure model (Hancer and Miller, 2000) and the colloid adsorption model (Leja, 1983; Burdukova and Laskowski, 2009). Most of the early exercises attempting to propose a unified rule on collector adsorption mechanisms can be seen as heroic endeavors due to the consideration of a vast number of salts in the pulp including alkali halides, nitrates, and sulfates, even the practically insoluble heavy earth metals. Additionally, several types of surfactants with different polarization features and alkyl chain length have been employed. As for the recent models, due probably to the preferential application of long chain amines as collectors in industrial potash flotation, most researchers are only devoted to collectors with low polarization features like amines and sulfonates (Hancer and Miller, 2000; Du et al., 2014). Collector adsorption mechanisms are therefore proposed based largely on a neglect of carboxylates as collectors. However, carboxylates remain an important collector type in soluble salt flotation systems where both salt minerals can be floated using anionic collectors and cationic collectors. Fatty acid type collectors are still one of the widely used collectors for soluble salt flotation and also one of the first to be applied on an industrial scale for the separation of potash ore (Hernáinz et al., 2003; Titkov, 2004). Here we examine some recent models that are relevant to our study to reveal a long neglected specific ion binding effects in potash flotation."

Jan 1, 2016

By Farid Mirahadi

Forecasting productivity of construction operations is a difficult but crucial task in planning construction projects. Over the past decades, many models have been developed to forecast productivity for different construction operations. Models made up of several functional relations and controlled by a specific number of control rules are more in line with human reasoning and logic. Neural-Network-Driven Fuzzy Reasoning (NNDFR) structure as one of these models shows a great performance for modeling datasets among which clear clusters are recognizable. Lack of the compatibility of conventional NNDFR with fuzzy clustering algorithms besides the insufficient attention paid to the optimization of number of clusters in this model, created a potential area for further research. The main contribution of the proposed model is to develop a modified NNDFR system to model construction data. To this end, Fuzzy C-Means (FCM) algorithm is substituted for K-means in NNDFR structure, and its parameters such as the number of clusters and weighting exponent are optimized through genetic algorithm. The proposed model is further verified through simulation of a construction operation in which several qualitative and quantitative factors are considered. Its implementation to the case study shows a considerable improvement of model performance with lower Mean Squared Error (MSE). The developed model assists researchers and practitioners in utilizing historical construction data to forecast productivity of construction operations with a high accuracy that could not be obtained by traditional techniques.

Aug 1, 2013

By Michael S. Moats, Alex Luyima, Tomas Oliveira

Some commercial copper electrowinning facilities use Cyquest N-900 (a polyacrylamide) or HydroStar (a modified polysaccharide) to improve the density and smoothness of copper electrodeposits. However, the effects of these additives have not been studied extensively in the open literature. Thus, the electrodeposition of copper at 40 oC from a non-stirred synthetic electrowinning electrolyte (40 g/L Cu2+, 160 g/L H2SO4, and 20 mg/L Cl-) in the presence of various concentrations of either additive was evaluated using cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS). CV results show that neither additive has much effect on the nucleation overpotential of copper electrodeposition on stainless steel. However, Cyquest N-900 polarized the copper deposition reaction upon the return sweep. The EIS data indicates that Cyquest N-900 increases the reaction’s charge transfer resistance and creates a second low frequency loop. HydroStar had minimal effect on the electrochemical data generated by CV or EIS. Thus, the mechanism by which HydroStar affects the copper deposition reaction still needs to be determined.

Jan 1, 2014

By J. A. Finch, A. M. Elmahdy

Blending frothers is becoming common in flotation practice apparently enhancing performance. However, there have been no studies to understand the blend mechanism. In this paper, the effect of two frother blends ofF150 (polyglycol) with MIBC or pentanol (both alcohols) on bubble size, gas holdup and froth height is reported. The blends focused on a small addition of the polyglycol to the alcohols as base frother. The tests showed that the bubble size at blend concentration below the critical coalescence concentration (CCC) of the base frother was decreased but was significantly larger above the base CCC. Froth build-up showed a strong synergistic effect.

Jan 1, 2009

By J. Shibata, N. Murayama, H. Yamamoto

As one of effective usages of wastes discharged in the non-ferrous metal industry, the syntheses of AlPO4-5 and hydrotalcite were carried out using aluminium dross as a raw material. AlPO4-5 is an aluminium phosphate condensate with properties of zeolitic materials and large pore size. Hydrotalcite is an inorganic anion exchanger and has a layered structure of complex hydroxide. They were synthesized in an autoclave at high temperature and pressure. Various physical properties such as crystal structure, surface texture, and specific surface area were measured. AlPO4-5 can be synthesized from aluminium dross under hydrothermal conditions at 180°C-200°C, and 3h. At the same time, AlPO4-34 and non-porous AlPO4 were also formed as by-products. The crystals of AlPO4-5 have a hexagonal structure. Lt is desirable to heat the reaction product at around 550 °C to remove tri-ethyl amine. The specific surface areas of the reaction product before and after heat treatment at 550°C were 17.9m2/g and 358m2/g, respectively. Hydrotalcite can be obtained by a co-precipitation method from the aluminium dross and waste MgCl2 solution discharged in the aluminium regeneration process. Small amounts of SiO2, Al2O3, and Fe2O3 remain in the reaction product as an impurity component. The interlayer distance of the obtained reaction product is about 0.3 nm. Hydrotalcite changes to Mg-Al oxide during calcination at 500 °C for 3h, and then hydrotalcite is formed again by a rehydration operation. The physical properties of the reaction products obtained from the wastes were very similar to those from fresh reagents.

Jan 1, 2004

By J. G. Schofield, R. C. Francki, K. M. Donaldson, F. E. Ham

"Developments in pyrometallurgical technology have led to larger furnaces operating under more intense process conditions. In order to maintain the reliability of these furnaces, which are frequently single-line units, the design of the refractories, cooling systems and bindings has become more critical. Traditional thermal and chemical requirements for the refractory to resist slag attack must still be carefully determined. The larger, modem furnaces have placed a new emphasis on the structural properties of the refractories as well as their thermal properties to suit the extensive cooling systems. Based on operating experience, supported by computer models, the refractories and bindings are designed to work together to accommodate the thermal expansions and contractions in order to minimize permanent furnace growth and the risks of leaks. IntroductionElectric furnaces are used extensively in smelting copper and nickel ores and concentrates. Laterite nickel ores and high-magnesia copper, nickel and platinum sulphide concentrates are smelted virtually exclusively in electric furnaces to accommodate the high melting point of the slags produced. Although a number of smelting processes using oxygen-enriched and/or preheated air have been developed to replace reverberatory furnace smelting of conventional copper and copper-nickel concentrates, (lnco, Noranda, Outokumpu, Mitsubishi) electric matte furnaces remain a strong process alternative for these concentrates, either as the primary smelting vessel or for cleaning the slags produced from these processes.The development of large, high-powered furnaces has been an important factor in the growth of electric smelting technology, as evidenced by the list of operating matte and ferronickel furnaces shown in Table I. Because the compressive forces required to maintain a tight, leak-free furnace increase with furnace dimensions, the selection and design of the furnace refractories, cooling systems and bindings require increased attention."

Jan 1, 1993

By Fulchand Shende

Around the world many potash mines experience brine inflow problems. The presence of brine in underground excavations may induce structural and stability problems. A study has been carried out to simulate the effect of brine on the performance of pillar support. The testing program consisted of loading potash specimens in a creep frame, and simulating inflows by continuously pumping brine into an experimental cell. Brine temperatures and load conditions were varied to simulate several mining and inflow conditions. Specimens were fitted with acoustic emission transducers to monitor energy emissions during an eight-hour test duration. Samples of brine were also collected to provide K+ and Na+ concentration data necessary for an accurate assessment of the dissolution process. Test results indicated that dissolution rates are highly dependent on brine temperature and load conditions. Loads approaching 50% UCS tend to generate very high rates of energy emissions, often leading to the failure of the simulated pillars. This study demonstrated that acoustic emission could be effectively used for predicting the performance of pillars when exposed to inflow brine.

May 1, 2001

By Seungwoo Park, Whuisu Shim, Roe-Hoan Yoon, Kaiwu Huang

"A comprehensive froth model has been derived from first principles. It is based on predicting the kinetics of film thinning in the presence of particles of varying sizes and surface hydrophobicity. According to the Reynolds lubrication theory, the thinning of a horizontal film is driven by the excess film pressure (p), which is determined by the capillary pressure (pc) and the disjoining pressure (II). In the presence of particles, macroscopic capillary pressure (pc) is affected by the local capillary pressure (pc,local) in the vicinity of a particle and the number of particles in the film (N1,film), which in turn vary with the hydrophobicity and size of the particles. The Reynolds equation corrected for pc,local and N1,film is then used to predict the time (or froth height) at which a film is thinned to a critical rupture thickness (hcr), which in turn can be predicted using the Vrij’s capillary wave model (1966) after a modification to incorporate the contributions from hydrophobic disjoining pressure (IIhp). The model can predict bubble coarsening represented by the bubble size ratio between the top (d2,t) and bottom (d2,b) of a froth as functions of particle size and hydrophobicity, ? -potentials, frother dosages, froth height, gas flow rate, salt concentration, etc. The model predictions have been verified in experiments.INTRODUCTIONFroth flotation is regarded the best available technology today for upgrading minerals and coal fines. In the pulp phase of a flotation cell, air bubbles collect hydrophobic particles dispersed in it and rise to enter the froth phase on the top. Once in a froth phase, the bubbles coalesce with each other and become larger, resulting in a decreased bubble surface area. Under conditions of limited surface area, less hydrophobic particles drop off the bubble surface and return to the pulp phase. Thus, bubble coarsening provides a useful mechanism of increasing product grades. On the other hand, uncontrolled coarsening results in a decrease in bubble carrying capacity and hence throughput."

Jan 1, 2016

The recovery of fine hydrophilic gangue in flotation is related to the recovery of water. Water is carried by bubbles as a film and wake into the froth. The amount carried (entrained) depends on bubble size, gas rate and the subject of this paper, frother type. To isolate the effect of frother type from that of bubble size and gas rate, gas holdup is used as the correlating variable. Measurements were made using a bubble column (no solids) operated continuously with the overflow recycled. Continuous operation meant some foam depth was required to ensure only entrained water is recovered. Using an automatically controlled 7cm foam depth the overflow rate of water is used as a measure of 'water carrying rate'. It is shown that the common frothers can be grouped into four families based on the water carrying rate-gas holdup relationship.

Jan 1, 2006

By Mustafa Kumral

Monte ? Carlo simulation is often used to assess the risks associated with uncertain variables in mining operations. The success of Monte-Carlo simulations depends upon reproducing the dependencies among variables to some extent. However, some variables may exhibit different dependency patterns. In these cases, classical techniques for dependency quantification cannot capture dependencies. As an alternative, the copulas allow modeling nonlinear dependencies. Furthermore, any choice of marginal distributions can be used. Especially, for the data, which is sensitive to extreme case such as financial crisis, the copulas arise as a means to reproduce the correlations among variables. In this paper, the copulas are introduced to mining practitioners using Monte-Carlo simulations for risk assessment. Then, a case study is given to show the superiority of the copulas over classical techniques using ModelRisk Software. In conclusion, it was observed that the copulas enhance the quality of Monte-Carlo simulations by capturing variable dependencies.

Aug 1, 2013

By Y. Zedan

Cutting fluids play important roles during machining, including the reduction of friction and temperature. Using a cutting fluid, however, degrades the quality of the environment and increases machining costs. The aim of the present research work is to study the effect of cutting fluids and their interactions with cutting parameters on the quality of holes during the drilling of 6061-T6 aluminum alloys. The lubrication types and modes investigated are dry machining, flood lubricant machining and minimum quantity lubrication machining (MQL), while the part quality criteria include the surface finish, the dimensional accuracy, and burr forms and sizes. A scanning electron microscope (SEM) was used to investigate the formation of built-up edges (BUE) in the drill flutes as well as the surface texture of drilled holes. It was found that dry machining and MQL machining can produce parts having quality levels comparable to those obtained in wet machining, when using the optimal cutting conditions.

Jan 1, 2011

By Ting An Zhang, Chengzhi Jiang, Xiujing Zhai, Feng Xie

The extraction and concentration of nickel from aqueous solutions by emulsion liquid membranes (ELMs) using tributylphosphate (TBP) as extractant has been investigated in this research. The emulsion liquid membrane consists of a diluent (kerosene), a surfactant (Span 80), a mobile carrier (TBP), and a stripping solution (ammonia solutions). Important factors influencing the separation process including membrane composition, feed composition, and mixing speed have been examined. The results show that more than 90% of nickel in the feed solution could be extracted by ELMs under the experimental conditions, indicating the feasibility to use the designated ELMs to detoxify nickel-containing industrial waste solutions.

Jan 1, 2014

By CRO CRO

Elk Valley Coal?s Cheviot Project is located in the Alberta foothills south of the town of Hinton. The mine has been in operation now for the 3 years. The start up and subsequent operation of the Cheviot project has been directly influenced by the Cardinal River Mine. As the Cardinal River Mine was winding down due to reserve depletion in 2004, the price of seaborne traded metallurgical coal jumped to record levels and customers began aggressively seeking new sources of supply. Several months later, the owners of Elk Valley Coal decided to begin mining at the Cheviot mining area, extending the life of the area?s operations by over 25 years. The Cheviot Project had been delayed by low coal prices, ownership changes and a complicated and lengthy regulatory process fueled in large measure by stiff opposition from a number of major environmental organizations. Chief to the startup of the project was the construction of a 23-kilometer-long haul road that would connect the new coal measures to the existing Cardinal River processing and rail facilities. Construction of this road was completed with the first coal truck making its first trip in October 2004. This paper will look at some of original assumptions, the actual mining experiences and the lessons that were learned while moving from the drawing board to the current development as it exists today.

May 1, 2007

By G. G. Li

"A dynamic ventilation-modeling package, VREX, was used to simulate the mine activities through tracking the equipment movements in underground workings and determine the airflow demand for a new production scenario in a ventilation-on-demand (VOD) system. It incorporates the mine development data from a discrete event simulation and balances the ventilation network using the CANVENT ventilation solver. A case study was performed to demonstrate the capabilities of the software, evaluate the performance of the network and determine the potential energy savings for implementing VOD in a deep mine operation.INTRODUCTIONThe ventilation cost of an underground mine can be significant—up to 50% of the mine’s energy consumption could be used to run fans and provide heat/refrigeration to meet the specified production environment for workers and equipment. The VOD system has proven to be more efficient in operating the fans and supplying the amount of air corresponding to the mine activities taking place in underground workings (Hardcastle, Kocsis, & O’Connor, 2006). In order to properly solve and evaluate the VOD system, a dynamic ventilation modeling software VREX—the ventilation rules engine has been developed to simulate the mine activities and determine the airflow demand for each production scenario within an operation period (Dasys & Cameron, 2011).VREX is a decision support tool, backed by the CANVENT mine ventilation solver (Li, Kocsis, & Hardcastle, 2009), for determining the outcomes of network configuration changes over time. The software incorporates the mine development data with ventilation modeling through the discrete event simulation (DES) performed by SimMineTM. As it simulates the air requirements for different vehicles and activities, VREX can evaluate both the performance of the ventilation system and the potential economic benefits of making operational or technological changes (Pritchard, 2010). For example, the model can be used to assess the economic and environmental impacts arising from modifying regulations to support the use of electric or lower emission vehicles. The combination of DES and ventilation modeling provides a new technology to generate the production scenarios according to mine schedules and activities and to determine the potential benefits for various levels of ventilation control, such as time interval and work shift change."

Jan 1, 2019

By Doug Milne

Linking Classification Systems with each other Similar Parameters between systems Different Rock Mass Properties Rock Mass Classification parameters and geology Different sources of data Commonly Used Rock Mass Classification Systems Q? = Q with SRF = 1.0 RMR? = RMR with no joint orientation correction RMR76 = 9lnQ + 44 RMR?76 = 9lnQ? + 44 RMR76 = RMR89-5 RMR?76 = GSI = RMR89-5 MRMR = ??MRMR

May 1, 2013