Search Documents

By Weiren Lin

The Mw 9.0 Tohoku-Oki, Japan earthquake occurred on 11 March 2011 produced a maximum coseismic slip of >50 m near the Japan Trench. To investigate why the plate boundary fault between the subducting Pacific Plate and overriding North American Plate which caused the earthquake had such unprecedented large coseismic displacement and slipped to the trench, Integrated Ocean Drilling Program Expedition 343 called Japan Trench Fast Drilling Project (JFAST) drilled three boreholes at Site C0019 through the earthquake fault about one year after the earthquake. Borehole C0019B dedicated to loggingwhile- drilling (LWD) penetrated ~850 meters below seafloor (mbsf) at a water depth of approximately 6890 m. The plate boundary fault is located at ~820 mbsf in the borehole and has been identified as the slip zone during the Tohoku-Oki earthquake. Borehole wall resistivity images obtained from LWD show that drilling induced borehole breakouts are available in a wide depth range above the fault but are not available below the fault. Breakouts are reliable indicators of the orientations of current maximum and minimum horizontal stresses and can also be used to constrain the horizontal maximum and minimum stress magnitudes. As results of breakout analyses, the maximum horizontal stress orientation highly varied in the upper part of the borehole, but has a clear preferred orientation in a northwest – southeast direction in the deeper part just above the fault. This orientation is approximately parallel to the direction of the Pacific Plate subduction. Stress magnitude constraints indicate that the post-earthquake stress states in the hanging wall are either in or close to the normal faulting stress regime. By inferring the pre-earthquake stress state and comparing with the constrained post-earthquake stress state, a significant coseismic stress change was interpreted. The stress change suggests an active slip of the frontal plate-interface consistent with coseismic fault weakening and a nearly total stress drop.

Jan 1, 2015

By J. R. Johanson, A. W. Jenike

"A solid flows out of a bin provided that the outlet is sufficiently large so that stable obstructions to flow do not develop. The geometry and surface finish of a bin and the construction of the feeder determine the type of flow pattern which then develops within the bin. The pattern, in turn, affects the uniformity and consistency of the stream, segregation, caking, degradation, live capacity and the action of level measuring devices.In most bins now in operation, material flows toward the feeder through a channel which forms within the stationary solid. This is referred to as funnel flow. If the hopper of the bin is sufficiently steep and smooth and the feeder capable of drawing material across the whole area of the outlet, all the solid flows whenever the feeder is in operation; this is referred to as mass flow. Mass-flow bins are usually far superior to funnel-flow bins; their initial cost is also usually higher.The paper describes the design criteria used in deter-mining the minimum bin outlet needed for flow and the bin geometry needed for mass flow."

Jan 1, 1970

By Bill Dupley

We believe that the inability of employees to effectively manage information has reached an epidemic problem throughout the corporate world. ? All the available knowledge in the world is accelerating at a phenomenal rate. ? The whole world's codified knowledge base (all historical information in library books and electronic files) doubled every 30 years in the early 20th century. ? By the 1970s, the world's knowledge base doubled every seven years. ? Information researchers predict that by the year 2010, all the world's codified knowledge will double every 11 hours.

May 1, 2003

By Sadan Kelebek, Gerhard W. Heinrich, Peter F. Wells, Peter J. Whittaker

"Based on plant mineralogical data & circuit modelling, a pilot plant campaign was conducted at Strathcona Mill to identify options for improving the performance and operating flexibility of the copper-nickel separation circuits. Emphasis was given to options for combined treatment of the two feed streams (primary nickel ore rougher concentrate and copper ore circuit concentrate) to obtain more flexibility in the use of existing column flotation capacities. The pilot test results demonstrated that circuits which incorporated preconcentration prior to column flotation gave the best metallurgical results. Maximum column carrying rates were also related to the preconcentration. Predictions that increased circulating loads from the column scavengers would improve copper-nickel separation performance were confirmed.IntroductionThe copper-nickel separation circuits at Falconbridge's Strathcona Mill produce a high grade (>30% Cu) copper concentrate most of which is treated at the Falconbridge Kidd Creek smelter near Timmins. The remaining nickel concentrate which still contains approximately 20% of the feed copper is combined with other lower grade nickel/copper concentrates and shipped to the Falconbridge nickel smelter. The separation is required because of the limited capacity for copper processing in and downstream from the nickel smelter. Since no nickel is recovered at present in the Kidd smelter, the challenge is to minimize the nickel content of the copper concentrate.At present there are two independent separation circuits treating the rougher concentrates from the copper and nickel circuits as shown in Figure I. The minerals treated are mainly chalcopyrite and pentlandite but there is up to 25% of the copper present as cubanite in the copper ore. The circuits were kept separate because the flotation rates and froth characteristics were very different, probably because of the presence of cubanite and the large difference in the concentrate grades feeding the circuits."

Jan 1, 1995

By O. Moselhi

This paper describes a method for selection of most suitable project delivery systems for capital projects. It expands upon the method advanced by the Construction Industry Institute (CII) in 2003, and incorporates additional decision criteria and project delivery systems in a multi-tier decision computational platform. The paper integrates the analytical hierarchy process to alleviate the inherent subjectivity associated with the assignments of relative weights to selection criteria used in the CII method. It also expands the range of project delivery options to include Public Private Partnership (PPP) and Integrated Project Delivery (IDP). The range of selection criteria was expanded by 60, beyond the 20 criteria of the CII method. Relative effectiveness values are proposed for the added project delivery systems making use of recent project cases in Canada and the USA. The method was implemented in a spreadsheet application. Multiple scenarios were considered for one of the cases presented in the CII study and a sensitivity analysis performed based on the developments made in this paper. The differences in outputs between the CII method and the proposed method are discussed. This is the first decision framework that incorporates both the presently used PPP and the recently introduced IDP, along with the widely used project delivery systems. The developed method allows users to filter out the factors and alternatives that do not apply to the case at hand, based on key inputs at the upper tier. The method is flexible and can easily be expanded upon and customized by the user.

Aug 1, 2013

By Bert Taylor

"The Mining concessions of Quemont Mining Corporation, Limited, are located at 48°16'N latitude, 79°00'W longitude, in Rouyn township, northwestern Quebec. Six hundred and forty acres in area, they lie directly north of, and contiguous to, the Horne mine of Noranda Mines Limited. The north arm of Osisko Lake covers a large area of the southern part of the property. The orebodies lie below the Jake with one body extending through to the bedrock surface.The property was staked in 1922, and was originally known as the Murray Claims. The group attracted interest from numerous exploration companies because of the proximity of the Noranda orebodies.The United Verde Extension Company, of Arizona, optioned the claims in 1926. They sank a shaft to a depth of 235 feet, at a short distance from the Noranda boundary. From a level established at a depth of 215 feet they completed 3000 feet of exploratory driving from which 6000 feet of diamond drilling was done. Only a small body of siliceous gold ore was found before they dropped their ·option.In 1928, The Mining Corporation of Canada purchased a 90 per cent interest in the property. An operating company, later named Quemont Mining Corporation, was formed. An electrical survey was carried out on a portion of the property, followed by deepening of the shaft to 922 feet. Levels were established at 500 and 900 feet, and 4,800 feet of driving and more than 3000 feet of diamond drilling were carried out from them.Geological knowledge at that time recognized that a major break, the Horne Creek fault, lay not far inside the south boundary. Striking north 80 degrees east, the fault dipped south at 85 degrees. The rock on the north side of the fault was massive rhyolite; to the south, meta-diabase and a little rhyolite. A left-handed movement was indicated by a 600-foot offset on a north striking diabase dyke. The small body of siliceous gold ore, referred to previously, was confined to the 215 level."

Jan 1, 1949

By F. L. Pellet, S. Maiolino

"The determination of rock bolt contribution to reinforced joint shear strength is still a challenge, especially for assessing reinforced rock mass stability. For this purpose, several experimental studies have been performed during the last decades, mostly on small scale rock joint and bolt specimens. However, to accurately assess the rock bolt contribution, scale effect has to be accounted for. For this reason full scale lab tests are required as an alternative to in situ tests for which boundary conditions are more difficult to control.In this paper the results of an experimental program carried out with a large shear box, dedicated to test bolts in full scale conditions is presented. Different rock bolt diameters and different rock bolts inclination with respect to the shear plane were tested Experimental results were satisfactorily compared with an analytical model which is able to compute the contribution of the rock bolt to the shear strength of the joint as well the associated displacement of the joint. These conclusions allows us to validate the model in order to help the designer of reinforced rock engineering structures, such as slope or underground openings, to precise the optimum installation of rock bolts. INTRODUCTIONFully grouted rock bolts are commonly used for rock masses reinforcement to ensure the stability of rock slopes and underground cavities. For this purpose, the determination of rock bolt contribution to reinforced joint shear strength is of the utmost importance. During the last decades, several experimental studies have been performed to investigate the behavior of bolted rock joint. For obvious reasons, almost all the experiments were achieved on small scale bolted rock joint specimens (Bjurström, 1974; Azuar, 1977; Dight, 1983; Egger & Fernandes, 1983; Schubert, 1984; Spang & Egger, 1990; Egger & Zabuski, 1991). These studies made it possible to assess the influence of different parameters such as the bolt’s diameter, the number of bolts, the angle between the bolt and the joint, the nature of the rock, the friction and the dilatation angle of the joint. However, to accurately assess the rock bolt contribution, scale effect has to be accounted for (Vallier et al., 2010). For this reason full scale lab tests have been performed as an alternative to in situ test for which boundary conditions are more difficult to control."

Jan 1, 2015

By John C. McKay

"The five papers which follow, under the heading of ""Technology Transfer-Universities to Industry"", were originally presented at the 20th Annual CIM Conference of Metallurgists in Hamilton, Ontario. They are a unique group of papers, unique because each paper is concerned with applied research done wholly or partly in a university environment and then translated into industrial practice.Universities can rightly be regarded as one of our nation's greatest resources-a veritable storehouse of knowledge and expertise. Yet, too often, this resource is overlooked or, at best, sparingly used by Canadian industry. Of course, university-based research cannot supplant industry-based research, nor vice versa; each type of research activity has its proper role in the over-all process of technology development.University-based scientists are best equipped to conceptualize, innovate, determine viability of basic premises and to verify these at the bench or small pilot-plant level. Industry based scientists are best equipped to develop ""bench-scale"" innovations into mature manufacturing practices. Thus, university-based scientists and industry-based scientists do not compete with, but rather complement, each other. Active, relevant university research enhances industrial research provided good communication between the two ""solitudes"" is continually nurtured.Good communication between industry and university is a prime objective of CSIRA/ACRIS (Canadian Steel Industry Research Association /Association Canadienne pour la Recherches dans d'Industrie Siderurgique), The directors of CSIRA/ACRIS foster improved communication by making regular visits to universities, by sponsoring projects and by providing lists to professors of uncharted areas where basic research is needed. More can be done to improve communication between industry and university, and it is the intent of the Association to do more.The five papers sponsored by CSIRA/ACRIS are examples of good communication and healthy cooperation. It is interesting to note when reading these papers that the cooperation arose, in each instance, as a result of different circumstances. However, there is a common thread and it is personal acquaintanceship-the university scientist/professor and the industry investigator/manager knew each other prior to the initiation of the project."

Jan 1, 1982

By Emile D. L. Rienks

We have studied the interaction of NO with the quasi-hexagonally reconstructed Au(100) surface. Using variable temperature scanning tunneling microscopy we have observed formation of the unreconstructed phase of Au(100) after NO exposure. This NO adsorption induced phase transition is observed in a window of temperatures around 170 K. Under the same conditions, CO and O2 cannot drive the phase transition, suggesting weaker interaction. Thermal desorption spectroscopy experiments provide an estimate for the strength of NO chemisorption on Au(100) of 57 ± 4 kJ mol-1.

Oct 1, 2003

By R. B. STEWART

A few days ago, while reading a report of the late Dr. Robert Bell in preparation for this afternoon's meeting, I found some impressive figures concerning the magnitude of the Hudson Bay basin. From the waters of the Bay itself, this great territory extends eastward 500 miles, westward l,300 miles to the Rocky mountains, and southward to the source of the Red river. It has a width of 2,100 miles from east to west, and a length of l,500 miles from north to south. Its area is almost three million square miles. It is not, of course, my intention to review the natural resources of this vast territory, but to confine my remarks to that portion of it adjacent to the waters of Hudson bay. A number of erroneous ideas exist in the minds of many concerning this northern country, especially as regards its latitude and climate. Burwell, at the entrance of Hudson strait, is in the latitude of 60 degrees or roughly that of the north of Scotland. The southern end of James bay has about the same latitude as the northern end of Vancouver .island.

Jan 1, 1928

By So-Yeong Lee, Moosang Lee, Seung Hwan Ahn, Ho-Sang Sohn, Jongshin Chang

It is necessary to understand the characteristics, phase changes and chemical reactions of flue dusts introduced from a furnace to an off-gas line in order to achieve the stable operation and the improvement. This study is to develop the dust reaction model for chemical reactions of dusts in an uptake shaft of smelting furnace and a waste heat boiler. Phase equilibria and reaction paths in this system were determined by thermodynamic calculation with experimental and industrial data. The oxidation reaction rate of dusts was determined by the gas film mass transfer controlling. And the sulfation reaction rate was evaluated by the unreacted shrinking core model. Kinetic parameters were estimated by reference data including industrial ones. The present study with the developed model shows various effects of temperatures, dust particle sizes, and O2 gas partial pressures on dust reactions. INTRODUCTION The flue dusts from a copper smelting furnace move along a furnace off-gas stream into an uptake shaft and a waste heat boiler (WHB) and electrostatic precipitator(s). It is necessary to control the dust quality in order to stabilize the operation because the sticking behaviors differ depending on the phase of dusts. Phase changes of dusts are caused by chemical reactions at given conditions such as temperature and partial pressure of gases. Therefore, it is required to understand the phase changes and chemical reactions of dusts in order to perform the improvement and stable operation. The present study carried out the investigation to understand their fundamental knowledge. Especially, this study was focused on the kinetics of chemical reactions of flue dusts, developed the model. In particular, the scope of development and utilization of the model was defined as the uptake shaft of the Mitsubishi S furnace and the S-WHB radiation section in the Onsan smelter. Information needed for the modeling work referred to data from these processes.

Jan 1, 2019

By Deni Côte, Michel Dagbert, Marcel Vallée

"Greater reliability of mineral deposit and reserve estimates can be attained through better quality control of the data and information acquisition, and the estimation processes. This paper reviews the following key requirements:1. greater awareness of the significant figures of both data and estimates, and better understanding of the probabilistic aspects of the estimates, their confidence limits and margins of error;2. greater reliability of the information that supports the estimates, by more explicit and more rigorous methods and standards for data acquisition and for interpretations;3. more quantitative estimations of geological/mineral continuity, based on improved three dimensional sampling patterns and the use of geostatistics; and 4. better integration at the project engineering and mine production stages, of the mineral deposit characteristics and mining method constraints, for more efficient mineral recovery and mine quality control.RÉSUMÉUne plus grande fiabilité des estimations des gisements et des réserves minières requiert plus d'emphase sur le contrôle de la qualité de I ‘acquisition de l'information et du processus d'estimation. Les exigences suivantes sont revues:1. le respect du niveau d'exactitude des données et des estimes en n'utilisant que le nombre approprie de chiffres significatifs des observations et mesures, et en exprimant le niveau de confiance et la marge d'erreur des estimations;2. l'amélioration de fa fiabilité des données par des normes plus rigoureuses pour leur acquisition et leur vérification, et par des méthodes plus systématiques d'interprétation et de modélisation;3. l'estimation plus rigoureuse de la continuité des minéralisations dans les trois dimensions des gisements, par des patrons échantillonnages mieux adaptes awe paramètres géologiquement minéralogiques, et par l'utilisation des méthodes géostatistiques; et4. l'intégration plus poussée, particulièrement lors de la planification de l'exploitation minière, des caractéristiques des gisements avec les contraintes des méthodes d'exploitation, pour améliorer la récupération et le contrôle de la qualité en exploitation."

Jan 1, 1993

By Sigmund J. Andersen, Eva A. Mørtsell, Jostein Røyset, Randi Holmestad, Oddvin Reiso, Yanjun Li, Øyvind Paulsen, Calin D. Marioara

"With the purpose of increasing the extrudability of lean alloys, we reduce levels of the alloying elements Mg and Si in a 6xxx extrusion alloy. To avoid sacrificing strength, we investigate the compensating effect of smaller amounts of lithium and germanium, alone and in combination. Recent studies by atomically resolved high angle annular dark-field scanning transmission electron microscopy (HAADF-STEM) together with density functional theory (DFT) calculations have demonstrated that while Li replaces Mg, Ge substitutes Si in the columns in the hardening ß’’-phase. Several studies have shown that Ge replaces Si in other precipitates as well, and that both Li and Ge promote precipitation and can improve macroscopic properties, like strength and thermal stability. The scope of the current work has been to investigate and document the combined effect of the two alloying elements. Of the investigated alloys, the one containing both elements displayed highest hardness, corresponding with a significant increase in precipitate number density. We used HAADF-STEM to determine the extent of Li and Ge in the precipitate structures.INTRODUCTION The two most important alloying agents, with respect to age hardening of the 6xxx alloy series, are Mg and Si. In general, 6xxx alloys are formed into their final shapes by rolling or extrusion, before being age-hardened at elevated temperatures around 180°C. The hardening effect during this stage is due to the formation of metastable, semi-coherent, precipitate needles along the three < 001>Al directions generally following the precipitation sequence (Marioara, Nordmark, Andersen, & Holmestad, 2006): Supersaturated solid solution ? atomic clusters ? Guinier-Preston-zones (pre-ß”) (Edwards, Stiller, Dunlop, & Couper, 1998) (Marioara, Andersen, Jansen, & Zandbergen, 2001) ? ß” (Andersen, et al., 1998) (Hasting, et al., 2009) ? ß’ (Vissers, Huis, Jansen, & H. W. Zandbergen, 2007), U1 (Andersen, Marioara, Vissers, Frøseth, & Zandbergen, 2007), U2 (Andersen, Marioara, Frøseth, Vissers, & Zandbergen, 2005), B’ (Vissers, Marioara, Andersen, & Holmestad, 2008) ? ß, Si (stable)"

Jan 1, 2018

By Stephen G. Hardcastle

Worldwide, metal mines are going deeper. For example in Canada there are six such mechanized mines planning production at 3000m (10,000?). Working at such depths challenges all aspects of mining including the provision of ventilation to supply an equitable working climate for personnel and machinery. This paper explores the overall challenges of supplying ventilation in Canada?s deepest mines and how the volumes required could be minimized. This is essential because it must be remembered that ventilation and refrigeration are not only costly items to supply, but the magnitude of their cost is also very sensitive to the volume supplied. For ventilation this is obvious because of the cubic relationship between volume and cost. In deep mines, the main function of ventilation is the removal of heat transferred from the strata and generated by the mining machinery, and the air volumes supplied are designed accordingly. The second consideration is the removal of other pollutants that could be harmful to humans such as diesel and explosive fumes. However, the need for ventilation at its present design levels could be reduced. This paper discusses the implications of such technologies as: teleremote mining and alternatives to diesel equipment on the magnitude of the volume supplied; ventilation-on-demand which recognizes ventilation as a costly and limited resource; plus other aspects, such as the benefits of controlled recirculation, local cooling, and heat rejection back to the strata to gain further advantage from new developments. Furthermore, this paper advances the need to be able to design ventilation systems more cost effectively and how such new advances as process simulators can be used in conjunction with ventilation simulators to explore the diverse options that could affect the air volumes required and provide more realistic economic data upon which to base design decisions.

May 1, 2003

By Bruno Bussière

Acid Mine Drainage (AMD) from mine wastes is one of the most environmental challenge currently facing the mining industry. AMD is the result of the natural oxidation of sulphides exposed to air and water. When mining wastes have the potential to produce AMD, these reactive wastes have to be managed to meet existing environmental regulations. The LTA site (property of Barrick Gold Corp.) contains sulphide tailings that have the potential to generate AMD. The closure option Barrick selected was to construct a multilayered cover with capillary barrier effects (CCBE). The main objective of this CCBE is to prevent the production of Acid Mine Drainage (AMD) from the tailings stack covering an area of approximately 60 ha. Since its construction in 1996, the cover has been monitored to evaluate its performance. Two of the measured parameters are volumetric water content and matrix suction. This paper presents some of the main results from the monitoring program that started seven years ago. The results show that the cover is largely able to maintain a high degree of saturation (greater than 85%) in the moisture-retaining layer. The actual performance of the CCBE on the flat surface of the 60 ha site is even better than expected at the design stage. The area that requires more specific attention with the LTA cover is the influence of slopes that can reduce the performance of the CCBE during dry periods. However, these effects seems to be local and do not significantly affect the overall performance of the CCBE to mitigate the production of AMD at the LTA site.

May 1, 2003

By C. R. Lattanzi, M. J. Davie, L. D. Smith, J. R. Goode

"The feasibility study determines the technical and economic viability of a project at the level of accuracy required by the owner to make an investment decision. The economic analysis usually includes calculation of the discounted cash flow. Key components of the cash flow include the project capital cost, the operating costs, construction schedule, production rate, product prices and financial details.This paper examines the feasibility study for a typical mining project. The paper discusses acceptable methods for the determination of the geological and mineable are reserves. The prerequisites for the development of suitable designs, and the calculation of capital and operating costs for the mine, processing plant, and infrastructure are reviewed. Important features of the cash flow analysis and its interpretation are presented.IntroductionThe commercial development of a mineral deposit invariably requires the investment of capital in preparing the deposit for production. It has always been necessary, therefore, to demonstrate to the investor of capital that production of a saleable commodity is both technically feasible and economically viable. The instrument typically used to make these determinations is the feasibility study .Traditionally, mining companies have been rather conservative in their approach to financial management. Until about thirty years ago, the capital required to develop a new mine was most frequently provided by internal corporate cash now and virtually all of the necessary technical and economic studies were performed &apos;in house&apos;. Under these circumstances, there was little standardization as to what constituted an acceptable feasibility study, and even less as to what constituted an acceptable measure of economic viability."

Jan 1, 1991

By D. L. Churcher, R. J. Perry

"In recent years much work has been don e to examine alternate underground backfill support systems with the objectives of improving ground support and reducing mining costs. This report deals with the work conducted at Placer Dome Inc.’s Dome Mine to develop a high density backfill system, taking advantage of the unique properties of this fill material, to address a backlog of large open stopes to sustain stable minewide ground conditions for future generations of Dome miners.IntroductionDome Mine began its existence in 1909 with the discovery of visible gold on a dome shaped outcrop located west of Porcupine Lake in northern Ontario. The orebody beneath this outcrop has supported one of Canada’s premier gold mining operations for 80 years. Production during this time of over 46 000 000 tons of ore has resulted in the recovery of II 500 000 ounces of gold and 2 000 000 ounces of silver. Mining continues today at a production rate of 3500 tons per day, with ore coming from both underground and open pit operations.During the life of the mine, different underground mining methods have been used to extract the ore from a complex deposit consisting of single and multiple vein structures.Cut-and-fill mining was introduced in the 1930s using sand fill and later hydraulic fill for support and to provide a working platform. A total of 1 800 000 tons of sand fill and 7 300 000 tons of hydraulic fill have been placed underground in cut-and-fill stopes. Until the late 1960sshrinkage mining was used extensively, particularly in narrow, steeply dipping zones. Bulk mining with small diameter longholes was introduced about this time, to take advantage of low production costs. Longhole blasting has often been used to recover low grade ore from the walls or sills of old shrink stopes, resulting in large open stopes. Backfilling of these open holes has been restricted to smaller stopes and associated with local ground conditions.In the late 1970s it was recognized that the number of large open holes which were being generated presented serious regional and minewide stability problems for future operations. With higher gold prices, economic ore reserves were being tied up in areas adjacent to multi-level open stope complexes. To stabilize these stopes and allow access, backfilling would be required."

Jan 1, 1990

By R. M. T. Raja Ismail

Shipping and stevedoring industry is going to witness a massive increase in the amount of containers to be handled while land constraints become more critical. Offshore transfer operations hence offer a preferable solution to deal with the surge in cargos rather than to expand the port outwards. Recently, there has been increasing research interests on offshore crane automation. Suspended cargos in a ship-mounted crane system are caused to swing due to the vibratory motion of the ship induced by ocean waves, which can lead to collision between cargos and deck. Therefore, it is vital for offshore crane systems to satisfy rigorous requirements in terms of safety and efficiency. This paper presents the modelling and control development for offshore boom crane systems. A second-order sliding mode control law is proposed for trajectory tracking and sway suppression control, making use of its capability of actuator chattering alleviation while achieving high tracking performance and preserving strong robustness. The asymptotic stability of the closed-loop system is guaranteed in the Lyapunov sense. Simulation results indicate that the proposed controller can significantly reduce the effect of disturbances coming from gusty waves and other dynamic loadings.

Aug 1, 2013

By Frank D. Shepherd

THE Gunnar Gold Mines property is on the west shore of Beresford lake, in the Rice Lake mining division, southeastern Manitoba. Gold was first discovered in place in the Rice-Beresford Lakes area in 1911 on the Gabrielle claim, now included in the San Antonio Mines property at Rice lake. Following an eastward trend of favourable prospecting ground, promising showings were next staked in the vicinity of Long lake during the years 1915 and 1916. At that time, William Walton and associates, among them Gilbert LaBine, staked the Eldorado vein, north of Long lake, and Eldorado Gold Mines, Limited, was formed to develop the property a Company that, later, was to become widely known through successful operation of its radium-silver mine at Great Bear lake, Northwest Territories. Continuing eastward from Long lake, Walton and his partners, Gunnar Berg, Leo Seaberg, and Wm. Quesnel, staked claims during the years 1920-24 in the vicinity of Beresford lake which, later, were to become incorporated into the Gunnar Gold Mines property. The presence of gold-bearing quartz on these claims had been known from the time they were staked, but an opportunity to consolidate them into a group was not forth-coming until early in the year 1933. Although promising gold showings had been disclosed during the performance of assessment work on individual claims, no continuous mineralization having mine-making possibilities was discovered until after the consolidation of the entire group. From this stage onward, progress was rapid. Active exploration was begun on August 1st, 1933, and late in October James Houston reported favourably on the property. On October 27th, Gunnar Gold Mines, Limited, was incorporated in the Province of Ontario to develop and operate the property. The Company is also registered in Manitoba. The authorized capitalization is 3,000,000 shares of $1.00 par value. Gilbert LaBine was appointed president of the Company, with James Houston as mine manager. Following completion of a diamond-drilling programme, planned in 1933, it was decided to install a mine plant capable of carrying development to a depth of 1,000 feet. A transmission line, 5 miles in length, was built to the Great Falls-Central Manitoba line of the Manitoba Power Company, Limited.

Jan 1, 1939

By R. K. Sidhu, N. L. Richards, M. C. Chaturvedi

Nickel base superalloy IN-738LC, strengthened mainly by the precipitation of y&apos; phase, is extensively used in hot sections of land-based and aero gas turbine engines. Fusion welding, which is one of the most commonly used joining techniques for the repair and fabrication of superalloy components, however, finds a very limited application in case of IN-738LC components, as the alloy suffers from HAZ cracking during welding and during subsequent postweld heat treatment (PWHT). The present paper reports on the two methods studied to reduce the HAZ cracking in as-welded and postweld heat treated GTA welded IN-738LC, viz., the use of various fillers during welding, and the use of appropriate heat treatments prior to welding. The results of the microstructural analysis and crack measurements indicated that the HAZ cracking in GTA welds of IN-738LC was significantly reduced by using age-hardenable fillers with Al+Ti concentration less than that in the base metal in conjunction with a preweld heat treatment developed by the authors.

Jan 1, 2006