Search Documents

By Bruce C. Smart

"Very little attention was given to the regulation of uranium mills by the Atomic Energy Control Board prior to 1974. The ore grade treated by Canadian mills in the past was in the order of 0.08 - 0.3% U and it was not difficult to keep the exposure of workers well below regulatory limits. Furthermore, uranium milling has also been substantially free of occupational illness because environmental control has been generally satisfactory (l).The discovery of higher grade ore bodies in Canada has resulted in higher radiation levels in one mill and this has partly contributed to a need for increased radiation monitoring in the mill. In addition, as greater insight is gained on the effects of radiation, the implementation of the ALARA principle is being stressed at all mills.The concept of ALARA was emphasized by the ICRP (International Committee for Radiological Protection) in 1977 and stands for '""as low as reasonably achievable'"". It is based on the premise that no proven threshold for potential effects of radiation exists and that the actual individual exposure should therefore be kept as far below the regulatory limit as possible, economic and social factors being taken into account."

Jan 1, 1982

By T. R. Yu, D. B. Counter

"Kidd Creek Mines primarily employs sublevel blasthole stoping for underground mining operations. During pillar recovery in No.1 Mine and panel mining in No.2 Mine, the free standing fill exposures may reach a height of 100 m or more. Consequently, a competent consolidated rockfill has been required to fill the mined openings.Since 1976, a total of more than fifty stopes and pillars have been filled with over four million tonnes of backfill. Fill exposures, up to heights of 100 m, have stood up well after blasting adjacent to the backfill.The fill material consists of a graded aggregate, Portland cement and ground slag. Sand has been occasionally mixed in the fill material to serve as avoid filler. The aggregate is prepared in a fill crushing plant, transported underground through raises, and hauled to the filling stopes by conveyors in No. 1 Mine and by trucks in No.2 Mine.Two mixing methods are currently in use. No. I Mine utilizes the free fall of gravity; the fill materials are sprayed with cement slurry as the aggregate departs from the conveyor into a mixing culvert. The other is the use of a rotary mixer on a batch basis in No. 2 Mine.This paper describes the fill systems, filling operation s, and the backfill quality control practice, together with various testing results related to improving fill quality as well as reducing fill costs.IntroductionThe Kidd Creek minesite, located 27 km north o f the city centre of Timmins, Ontario, produces 4.5 million tonnes of copper, zinc, lead, and silver ores annually from its No. 1 and No.2 underground mining operations. Both mines employ a sublevel blasthole stoping method."

Jan 1, 1983

By Melissa Whellams

?? What is a social risk assessment (SRA)? ?? Why do a SRA? ?? When do you do a SRA? ?? How do you do a SRA? What is a social risk assessment? ?? SIA vs. SRA ? SIAs determine how a company?s project will affect social/cultural conditions in a region ? SRAs determine how social/cultural conditions will affect the risk profile of a company?s project Social risk context includes: ? review of human rights record ? analysis of conflict situation ? analysis of political climate ? stakeholder identification ? stakeholder concern/interest identification ? And so on?

May 1, 2008

By Christopher McElman

Real-time mine management solutions have evolved over time from closed, proprietary solutions, to a "system of systems" that may include a wide variety of off-the-shelf components and technologies. Modular Mining Systems has embraced open standards for their NextGen products to bridge the technology gaps between these systems. However, the remaining logical gaps must be overcome, in order to achieve truly seamless integration between discrete systems. When dealing with volatile real-time management problems, the effectiveness of business process modeling and middle-ware can break down. Scientific principles of military command and control applied to mining domain help to achieve better alignment and reach the highest level of integration. The combination of open standards and off-the-shelf hardware and software with a deliberately structured command-and-control approach provides a clear evolutionary path from ad-hoc connected systems towards real-time management of a seamlessly integrated digital mine.

Oct 1, 2009

By J. L. Blaylock

Normally, the hydraulic system and structures are considered to be unrelated items. In reality, the two cannot be separated because one affects and depends on the other to function properly. This paper explores the potential failure areas of hydraulic cylinders, and suggests possible methods to prevent failures from occurring. The use of high-strength low-alloy steel in frames is reviewed and the benefits discussed. Fabrication techniques and handling of material are noted in the hope that this knowledge will aid in the repair of frames in the field.

Jan 1, 1979

By Ken Wood, Luc Duval

"The development and operation of the milling circuits treating the different Selbaie orebodies are discussed in this paper. The project is reviewed from metallurgical evaluation through construction to present operating status. The current flowsheets are described, with discussion of some unusual features.IntroductionThe Selbaie concentrator commenced initial production in August 1981, treating underground B zone copper ore in a single 1500 t/d circuit. Throughput was increased to 1650 t/d in 1985. The mill was expanded in 1986 to treat ore from the A-I zone open pit; an independent circuit was added to selectively treat 5000 t/d of copper-zinc ore. Current total mill throughput through both circuits averages 7200 t/d with the production of approximately 270 t/d of copper concentrate and 230 t/d of zinc concentrate.This paper describes the stages involved in bringing the project from initial laboratory testing to its current status as one of the most important producers of silver, copper and zinc in Quebec and a major employer in the region."

Jan 1, 1990

By B. W. Snyder

INTRODUCTORY THE earliest known case of transmission of natural gas by pipe lines was early in the Christian era when the Chinese used bamboo pipes to transport natural gas from surface seepages to heat brine for the recovery of salt. Since that time many materials have been used as conduits-hollow wooden legs, wood stave pipe, day tile, cast iron, and, finally -since about 130 years ago - steel pipe. Even then, this new material came into use rather . slowly for, as recently as 80 years ago, wood pipe was still being used. However, as techniques were developed to take advantage of the properties of steel, this material gradually replaced all ethers for the transportation of gas for longer and longer distances at ever increasing pressures. In 1912, one of the longest pipe lines of its size at that time was built-this was a 16-inch line bringing gas from Bow Island to Calgary, a distance of 170 miles. We have been able to find records of only two ether such lines at that time-one a 185-mile 16-inch line from Vivian, Louisiana, to Little Rock, Arkansas, completed in the summer of 1911, the ether a 280-mile line from West Virginia to Toledo, Ohio. This last ? mentioned line was reported in a magazine article of September, 1912, but no indication was given of its size on completion date. It is apparent, therefore, that modern high pressure transmission of natural gas is a technique less than forty years old.

Jan 1, 1951

By G. R. Haiden, E. Henderson

"An LHD teleoperation and guidance system, developed at the Ontario Division of Inco Limited, has been demonstrated in operation at Copper Cliff North Mine (CCNM) since late September, 1993. The tests performed to date have evaluated the feasibility and production viability of multiple LHD operation, from surface by one operator.The systems technology required to accomplish this consists of an electronic monitoring and control package mounted on the LHD; a high bandwidth mining computer network capable of providing radio frequency coverage; and an operator control console which provides an operator workstation for multiple LHD operation.This paper discusses the systems required to accomplish the task of LHD teleoperation and guidance, the benefits of multiple machine operation and future research and development directions. IntroductionSince underground mining began, persolU1el have entered the mine workings to mine ore. Today, however, the rapid advancement of modem telecommunications, computer hardware and software technology has opened the door to remote mining technology that was considered unfeasible a few years ago. This paper discusses the ingredients of remote mining technology that have been developed at Inco Limited.Figure I represents an historical view of the application of electronics to LHD operation at Inco Limited. In 1980, the first radio remote controls for the operation of LI-IDs in large open stopes were tested. The successful application of this technology at Inco went hand-in-hand with the development and application of the Vertical Crater Retreat mining method. The combination of these two advances had a very positive effect on the productivity in the mid-eighties at Inco. In 1991, the Mines Research Department of the Ontario Division advanced remote control technology by developing a high capacity underground mining telecommunications system. This system is capable of moving voice, data and video information throughout the mine workings. The system is based on broadband communication technology found in most automated factories, with the added benefit of providing the information to and from mobile equipment through radio interfaces. The first test of the system consisted of an operator teleoperating a single LHD (on the 3000 ft level) from the surface. The next test on September 13, 1993, demonstrated the first production application of multiple LHDs being run from surface with a single operator."

Jan 1, 1994

By Y. C. Kim

This paper discusses Air Liquide's patented SPALTM (Surface Protection Air Liquide) technology and process for the inerting of coreless induction furnaces using cryogenic liquid gas. Air Liquide Canada Inc., in collaboration with Riverside Brass and Aluminum Foundry Limited (Riverside Brass), conducted plant trials to demonstrate the applicability of the SPALTM technology for copper-based alloys. Results showed that with SPALTM, Riverside Brass benefited from a significant increase in metal yield as the level of dross formation was drastically reduced. Together with the many other benefits of this technology, SPALTM demonstrated to be a non-negligible cost-effective solution to reduce metal production costs. In an effort to optimize the argon flow, different flow rates were used and the oxygen level above the metal bath was measured to pinpoint optimal flow. The results of metal yield, charge mix, dross formation, and melt temperature are compared with and without argon. The metal yield improvements are dramatic and calculated net savings are presented hereunder.

Jan 1, 2007

By J. W. Matousek

Tonnage oxygen plays a critical role in the primary production of two of the most important industrial metals - copper and iron - and minute quantities of oxygen play equally critical roles in determining the properties of the market products. For refined copper, oxygen in the final metal is balanced between maximizing electrical conductivity, neutralizing the effects of harmful impurities, and ensuring that the metal takes on the desired "set" during casting - the surface texture and physical properties required for subsequent rolling and drawing. For refined iron, oxygen must be removed to minimize reaction with carbon during cooling from the molten state with the generation of CO and CO2 - leading to a loss of carbon and the creation of "blow-holes" in the solid ingots and the potential for defects in rolled and forged products. This paper reviews the thermodynamics of oxygen in molten copper and iron at the levels of primary interest to production metallurgists.

Jan 1, 2014

By James E. Rider

"Fractures in mine hoist drumshafts are rare. We know of no previously reported attempts to repair a fractured drumshaft; any feasible method would involve welding and the associated problems of distortion, crack formation and strength.In June 1984, a fracture was discovered in the drumshaft of the production hoist in the Teck Corporation, Lamaque Division Mine at Val d'Or, Quebec. Delivery time on a new shaft would have been at least six months. The shaft was repaired in ten days and the total out -of-service time was four weeks.This paper describes why the shaft failed, how it was repaired, and the special alignment procedures employed during re-installation to minimize stresses in the repaired area.IntroductionThe performance of a mine hoist drumshaft is absolutely critical to mine operation. An inoperable drumshaft means no hoist, which in turn means no production or mine operation.Fractures in mine hoist drumshafts are rare. Previously when they have occurred, no one has seriously considered attempting a repair because of problems involved. Any feasible method would involve welding, which raises several major problems - namely, metallurgical, alignment, and strength.In July 1984 this very situation occurred at the Teck Corporation, Lamaque Division Mine in Val d'Or, Quebec.It was recognized that a new shaft would take at least 6 months' fabrication and delivery time. However, having had some experience at repairing broken shafts in other machines under similarly desperate circumstances, and after due consideration, it was concluded that by applying the correct techniques and engaging the right expertise, it would be possible to perform a repair and have the mine back in operation within a month.Thanks to outstanding efforts by all, the repair was accomplished in ten days and total out-of-service-time was only four weeks. The causes of the failure were determined and the calculated stress levels confirmed by strain gauge measurement during operation.The success of this project was achieved by adhering rigorously to fundamental management and engineering principles."

Jan 1, 1988

By Donald J. MacNeil

The commercial carbonate industry of Cape Breton Island, Nova Scotia, began about eighty years ago with the opening of the Sydney steel plant. Significant carbonate deposits are confined to the Precambrian George River Grav" and the Mississippian Windsor Group. George River Group carbonates are thought to have formed as part of a stable platformal sequence. They are crystalline and lie within a dominantly quartzitic sequence. Of the four major sites for George River carbonates on the island, the most commercially promising are the dolomite at Kelly Cove and the limestone and dolomite at Glencoe. Kelly Cove dolomite has good potential for metallurgical, agricultural and fettling purposes; reserves approach 13.6 million tonnes. Windsor Group carbonates were deposited as marine sediments in basins formed by pre-Carboniferous fault blocks. Windsor dolomite reserves at Stoney Creek are only fractionally retrievable and hence are of little economic value. The Windsor Group's Irish Cove limestone has been quarried on a large scale since 1964; no undeveloped commercial deposits, however, remain in the group.

Jan 1, 1984

By M. Stelter

Since the first years in copper electrorefining natural products have been used as so called "additives" in the electrolyte. Glue as one of these additives offers a lot of different reactions with the metal ions and also with other additives like thiourea in the electrolyte. For a deep understanding of the effect of these additives it is important to know the routes of possible reactions in the electrolyte as well as the basics of electrocrystallization. Using this knowledge the interpretation of nodulation or inclusions of electrolyte in the cathodes in copper electrorefining is easier than before. Setting up on physical and chemical properties of the electrolyte and the additives practical investigations of the effects of additives in copper electrorefining and their impacts on copper crystallization and cathode quality are presented in this paper. Chemical deposition of glue against time and temperature are only few of the effects that are mainly caused by the use of natural products. In fact parameters like anodic and cathodic polarization are strongly affected by the additives as well as the effects of the additives are strongly affected by current density. This second part of the paper presents results concerning interactions of the above mentioned parameters.

Jan 1, 2007

By Shamil Shaikhutdinov

CO adsorption on gold particles deposited on well-ordered alumina and various iron oxide films has been studied with temperature programmed desorption (TPD) and infrared reflection adsorption spectroscopy (IRAS). Structural characterization has been performed with scanning tunneling microscopy. Data show that the CO adsorption exhibits a size effect in that small particles adsorb CO more strongly. The effect generally vanishes after annealing to 500 K. For annealed samples, CO TPD and IRAS spectra are nearly independent of the particle size and supports studied. The results indicate that the CO interaction with gold surfaces is essentially similar and involves low coordinated atoms.

Oct 1, 2003

The North Saskatchewan River flows southwest to northeast through a 22-km-long valley in the City of Edmonton, supplying the drinking water to dozens of downstream communities. During heavy rains, combined sewers occasionally overflow into the river, which has a significant negative impact on the water quality and the sensitive environment. The West Edmonton Sanitary Sewer (WESS) W12, a syphon connecting the Rat Creek Trunk to the Gold Bar Wastewater Treatment Plant across the river, was designed and constructed to take the overflow to the wastewater treatment plant. Due to the complexity of the project, various 3D technologies were applied to facilitate decision-making processes. 3D models were developed for design review and design conflict detection, while 4D models were established to help create a robust construction schedule. Construction sequencing animation was used to convey design intents and demonstrate construction stages to contractors and workers. The combined applications of 3D technologies helped the project team to identify critical issues, and assured effective communication among engineers, management, contractors, and other parties. Therefore, it provided more opportunities for the success of the project.

Aug 1, 2013

By B. T. Lu, J. L. Luo, H. X. Guo

This paper investigated the synergistic effect in the slurry-erosion process of carbon steel. In line with the mechanisms of material loss, the synergism due to interaction of erosion and corrosion was divided into the corrosion enhanced by erosion and erosion enhanced by corrosion. The erosion-corrosion tests were conducted with A1045 steel in slurries containing silica sand. Experimental results showed that the rotating of the sample in corrosive media raised both OCP and corrosion rate, but the impingement of solid particles did not affect the corrosion current significantly. In the quiescent solutions, the Faraday's law gave a good prediction for the weight loss caused by corrosion but for rotating samples, the weight loss experimentally measured was virtually greater than that predicted by the Faraday's law, indicating that the corrosion-enhanced erosion could occur in corrosive fluids in absence of solid particles. A half-logarithm relationship was observed between the weight loss due to corrosion-enhanced erosion and the anodic current density.

Jan 1, 2004

By J. A. Hillier

"IntroductionThe purpose of sampling is to remove a portion of material from a stream which is representative of it in size, moisture and mineral content.To prevent the effects of segregation, generally caused by the way in which a conveyor, pipe or launder is loaded or directed, the sampler should cut proportionally the entire cross section of the stream.If one conveyor transfers to another at a right angle, fines may be dropped on the near side, and the coarse material thrown to the opposite side. Segregation can also occur as a result of the motion of a conveyor belt passing over the idlers causing the coarse material to roll to the sides of the belt.When slurry changes direction of flow in a launder or pipe, the heavier and coarser fraction will centrifuge to the outside of the curve and tend to remain on one side of the stream. Similarly, if two streams joining in a common launder are not mixed at the point of confluence, they will continue down the launder unmixed . This effect is particularly noticeable in a plastic lined launder.Therefore, a proportional sample is usually accomplished by a constant rate of cutter travel across the entire stream, making certain that the cutter is not full or splashing over before reaching the end of travel.The cutter should operate on a constant interval based on time, tonnage and uniformity of flow. The opening should be at least three times the width of the largest piece to be sampled. The cutter width is more critical with ore samples where particle sizes are large. With slurry samples, the opening is usually much larger than the minimum in order to obtain sufficient samples"

Jan 1, 1989

By Dennis Martin

What is Borehole Hoisting Borehole Hoisting is the use of a hoisting plant to hoist rock, workers and materials or both, vertically through a borehole, between a mine level and surface or between two levels of an underground mine. Screen and bolt ground support on walls of 5.5 m diameter borehole hoisting shaft

May 1, 2013

By Ron Davidson

"The Utility Mine in southeast Saskatchewan is owned by Saskatchewan Power Corporation and operated by Mana/ta Coal Ltd. Up to 3.3 million tonnes of lignite is supplied annually to Saskatchewan Power's Boundary Dam Generating Station. The coal occurs in two predominant seams which are covered by up to 37 metres of saturated fine-grained overburden. Overburden is removed by two draglines working in two pits. Coal is hauled to the mine mouth power station. Comprehensive drainage and reclamation programs are integral parts of the operation. IntroductionThe Utility Mine is owned by Saskatchewan Power Corporation and operated by Manalta Coal Ltd. It is located in southeastern Saskatchewan, approximately 200 km southeast of Regina and 8.5 km southwest of Estevan (Fig. 1). The climate of the Estevan area is semi-arid with long, cool winters and short, hot summers. The mean annual precipitation is 42 cm and the mean summer temperature is 20°C; mean winter temperature is -10°C. The Utility Mine supplies coal to the adjacent Boundary Dam Generating Station. Increases in the station's generating capacity during the past decade have resulted in an extensive expansion program for the Utility Mine. This expansion program, the geological conditions present in the area, and the mining/reclamation operations will be highlighted in the following sections<1.2). History The Estevan area has a long history of coal mining. In the early years, coal was mined via entries into coal seam outcrops along the slopes of the Souris River valley. Surface strip mining was introduced in the late 1920s and progressed to the point where it totally replaced underground mining by the 1950s. Surface mining methods are currently used exclusively by all of the Estevan area operators."

Jan 1, 1985

By J. W. Reynolds

This paper describes the function of the research and development department of a large mining organization and the benefits which can be derived over the years. Examples are given of work done in rock drilling, ventilation, noise control and the development of backfill stowing machinery.

Jan 1, 1970