Search Documents

By J. R. MacDonald

MINING literature contains very few descriptions of operations producing as little as 25 to 30 tons of ore per day. The purpose of this paper is to discuss the gradual development of a mining method for such a small-scale operation at the No. 2 mine of Central Patricia Gold Mines, Limited, and in doing so to review several systems of stoping applicable to narrow ve1ns. MAIN ECONOMIC FACTORS TO BE CONSIDERED (1) Overhead.-The outstanding feature of most mines operating on a single narrow vein is chat of small daily tonnage. The reason for this low output can be readily understood. The strictly limited ore-reserves present a condition unfavourable for a policy of large initial expenditures, with the result that the capacity of the plant provided must be governed by the? amount of ore in sight at the time when mill construction is planned. This is immediately reflected in the cost per ton, there being relatively few tons over which to distributed the more or less static charges, such as hoisting, heating, supervision, administration, pre-production expenses, and other write-offs. (2) Development.-In mining this type of orebody, the main factor contributing to high costs is unquestionably the small tonnage of ore made available by a given amount of development. Thus, for example, from the data tabulated below it can be seen chat, assuming a 12-in. vein and a drifting cost of $9.00 per foot, the development charge for this item alone would be 71 cents per ton. Add to this the charges for raising, cross-cutting, shaft-sinking, and pumping, besides charges arising from development in waste, and the figure will be very considerably higher than 71 cents.

Jan 1, 1941

By S. Yano, S. Takagi, Y. Nagaya, T. Akai, T. Ishida, Z. Bennour, T. Suzuki

"It is often reported that the concept of single-plane-fracture is not sufficient to account for the productivity from shale gas/oil wells. Many researchers introduce the concept of the stimulated reservoir volume to describe observed production behaviour. However, the characteristics of the stimulated reservoir volume are not well understood. In this study, to investigate the characteristics of fractures and surrounding region induced by the hydraulic fracturing, a devised hydraulic fracturing experiment was conducted using the cylindrical shale specimens in the laboratory.Two resins were prepared as the fracturing fluid for the experiments: cyanoacrylate, an instant glue, mixed with a fluorescent paint (resin A), and methyl metaacrylate, a thermosetting acrylic resin, mixed with a fluorescent paint (resin B). These resins were able to fix within the specimen after fracturing. This is because the present study aimed to only detect fractures induced by hydraulic fracturing. Cut sections of the specimens were observed under ultraviolet light irradiation. It is expected that the hydraulically induced fractures and the surrounding regions will be detected because the induced fractures filled with the resin should emit light, while the other parts will not.The specimens, which were collected from the Kushiro Coal Mine in Hokkaido, Japan at the depth around 275 m, were roughly 85 mm in diameter, 170 mm in length, and cored normal to the sedimentary planes. An injection hole with a 10-mm diameter was drilled onto the center of the specimen parallel to the sedimentary plane to simulate hydraulic fracturing in shale gas development. The experiment was conducted under a uniaxial loading condition of 3 MPa and the fracturing fluid was injected into the sealed injection hole at a constant flow rate using a syringe pump.After the fracturing experiment, the resins were fixed in the specimens and then the cut sections were observed under ultraviolet light irradiation. As a result, the hydraulically induced fractures, which were filled with the resin, are clearly observed. Detailed microscopic observations show that the main fractures are tortuous and are accompanied by many thinner ramified fractures. Additionally, fractured regions where the resin penetrates significantly are observed around the main fractures in the specimens fractured by the resin B. These induced fractures and fractured regions are considered to be the stimulated region in which permeability is improved. The necessity of estimation on the features of fracture tortuosity and ramified fractures is indicated for more accurate understanding of the well production and the stimulated reservoir volume."

Jan 1, 2015

By David Morrison

Our present longwall problems in Cape Breton can be grouped under five main classifications. These are: (1) Roof control on the face and on the main roadways leading thereto. (2) Transportation of coal along face and levels. (3) Mechanical loading at the face. (4) Safe method of conducting and applying power at the working faces. (5) Dust nuisance. The usual layout for longwall operation in Cape Breton is to have three, and sometimes four, faces in line with each other, the length of face being from 400 feet to 500 feet (see Figure 1), and producing between 425 and 500 tons per face. Each wall is serviced by a well constructed roadway for transportation of coal, men, and materials, and is operated as an independent unit. Each wall works under a regular cycle of operations: first, cutting and boring; second, drawing hardwood chocks, building midwalls, and shifting panlines; and third, loading. The present method of roof control and operation of longwall faces has developed through trial and error since the commencement of longwall miring in Cape Breton. The basic method of roof control in all longwalls in Cape Breton is: rigid support of the roof in the immediate vicinity of the working faces by hardwood blocks, as shown in Figure 2, accompanied by a cushion support furnished by continuous midwalls, 12 feet wide, constructed of stone obtained from the waste and spaced at 50-foot centres. These midwalls are kept forward to within 4 feet to 10 feet of the working face and allow a gradual subsidence of overhead strata, thus preventing any sudden break at the working face.

Jan 1, 1947

By P. Mattar

The geotechnical importance of studying fluid flow through porous media and soils in particular, becomes evident when dealing with groundwater movement in surficial geomaterials that can be initiated by hydraulic gradients that develop during construction activity, groundwater extraction, impounding of reservoirs and groundwater recharge during adverse climatic events. In a geotechnical context, rocks are regarded as virtually impermeable materials, with comparatively greater resistance to flow of water through their pore structure. The importance of the permeability of rocks comes to the forefront when deep geologic formations are used in geoenvironmental activities for disposal of hazardous and toxic materials. The permeability of the rocks encountered is of critical importance to these geoenvironmental activities since the movement or transport of the hazardous materials during their eventual release will be largely governed by the permeability characteristics of the geologic formation. The estimation of the permeability characteristic of geologic formations is a non-trivial exercise since the measure of permeability can be influenced by the scale at which the measurement is made. Regional-scale and borehole-scale estimates of the permeability can be greatly influenced by the inhomogeneities, including fractures, fissures, solution channels and other anomalies that are present in naturally occurring geologic media. These anomalies are considered to be site specific and can only be determined in a reliable fashion by either conducting tests at the appropriate scale or in the regional-scale through inverse analysis of tracer movement patterns in rock masses. The estimation of the permeability of intact units of a geologic medium has important geoenvironmental applications in connection with storage of wastes since the units in which repositories will be located should be sparsely fractured and the sealing of the fractures and fissures are a prerequisite to developing an efficient solution for storage. The intact permeability of geomaterials is therefore regarded as an important property that influences efficiency and reliability of geoenvironmental solutions for deep geologic disposal. The permeability of geomaterials such as concrete and cementitious grouts are also important to many geoenvironmental and infrastructure applications where durability of structural materials in general and cements used for sealing deep boreholes and other access shafts employed in waste management endeavours is influenced by the permeability characteristics of these materials

May 1, 2009

By S. Kamado

Development of new SF6 alternative cover gas with low global warming potential is strongly desired for melting and casting of magnesium alloys. We have tried to apply several kinds of HFC and HFE gases with low potential from 30 to 950 as protection gases to AZ91D alloy melt in the temperature range of 650 to 800°C. As a result, protective film consisted of MgF2 and MgO is formed on the melt surface and ignition-proof effect is sufficiently obtained at all the temperature ranges even when flow rates of mixed gases containing CO2 as a carrier gas are almost the same as those using SF6 gas. Reduction of global warming potential exceeds 98% at 650°C and 89% at 800°C in comparison with a mixed gas of CO2 and SF6.

Jan 1, 2006

By R. W. Thompkins

"PREFACEPart 1 of this paper, published in the September issue, covered the occurrence of uranium, radiation from uranium ores, the uranium series, radioactive theory, radioactive equilibrium and application to the radon series, the working level, the theory of emanation and diffusion, transport by thermal diffusion of radon emanating from porous rocks, and definitions.The October issue carried Part 2, which dealt with radiation theory applied to uranium ores, other radon migration factors, factors affecting the radon gas release rate, the measurement of radon gas emanation rates, the tunnel concept, variation of emanation rate with grade and estimating radioactivity from grade analysis.Part 3, in this issue, concludes the series by discussing the techniques for controlling radiation and providing some example calculations.17.0. Techniques for Controlling Radiation17.1. Altering the Factors In the Diffusion EquationIt has been noted that radon gas emanates from the surfaces of exposed ore to the mine atmosphere. The diffusion laws establish the rate of this flow. The fundamental relationship is that the rate of flow (J) is a function of the pore concentration and the distance from the surface. It is expressed as: []If any of these terms is varied, either naturally or artificially, the rate of gas emanation will be altered.Altering the Diffusion CoefficientThe literature describes many ways to lower the radon gas emanation rates which are dependent on changing the diffusion coefficient:1. A layer of ice on top of a tailings dam or on a soil.2. Humid clayey materials and swamped soils over a radon source."

Jan 1, 1982

By M. A. Nadar

Harsh and dynamic construction sites are generally equipped with cranes in order to rapidly and conveniently move heavy loads from one location to the other. If not properly inspected and managed, this operation can be very hazardous and lead to accidents. As such, a reliable and self-contained monitoring system that can update construction and safety personnel about the status of the crane, the weight of the load lifted, the location of the boom with respect to nearby buildings and other tower cranes, and the weather conditions under which the crane is operating, is deemed necessary. This can lead to significant time and cost savings as well as safety and productivity improvement due to the accuracy and immediacy of relevant on-site crane information delivery. This paper takes the initial steps and presents research targeted at evaluating the capability of wireless sensor networks (WSN) for monitoring tower crane operations in construction environments. A reliable long range WSN system is implemented and information is obtained from various special-purpose sensors (temperature, wind, proximity, etc.) mounted on special motes that relay data to and from each other and a central hub. The latter continuously monitors and manages network performance and relays incoming data to the host application. This application, in turn, displays the received data, and maps it onto a user-friendly visualization scheme, triggering alarms when a set of pre-programmed rules and safety conditions are crossed. The components of the proposed system have been tested through proof of concept experiments and preliminary results highlighted the potential of WSN systems for improving monitoring of tower cranes and reducing related accidents on construction sites, especially in Lebanon and the Middle East region where safety precautions are usually not properly implemented.

Aug 1, 2013

By G. Begin

"The expansion undertaken at Selbaie in 1985 necessitated an adaptation and expansion of the equipment maintenance system. This paper relates briefly the stages of transformation of the maintenance administrative structures, work methods and tools. The maintenance in a mechanized mine requires an expenditure level in the order of 20% of the total operating cost of the enterprise. Thus, the maintenance organization was modified to apply more computerized planning and follow-up, and the role of preventative maintenance was further advanced.IntroductionAs far as maintenance is concerned at Selbaie, the scenario described herein is a resume of the current situation. Although positive results have been obtained, this outline is in no way a detailed account of a fail-proof maintenance system.Once zone A-I was put into production, the expansion the mine experienced in 1985 had a direct impact on the equipment maintenance system. As centralized as it was in the beginning, the system is now partially decentralized.The over-all changes to the maintenance department demonstrate the flexibility required by organizations in new situations. In spite of the exceptional results obtained before the expansion, it became evident that both the maintenance and production sectors would have to be combined. In doing so, a more appropriate coordination of maintenance work could be obtained and the maintenance staff would obtain a more detailed knowledge of the equipment in each sector. In addition, by keeping the general and specialized departments centralized, it was possible to offset the negative effect s of a decentralized system, namely too much manpower."

Jan 1, 1990

By Frank Wright

"The Icon Sullivan Joint Venture ore deposit was discovered in June, 1965 by Messrs. Paul Benard, Bob Galipeau and Mac Watson working under the direction of Mr. Andrew J. Troop, as employees of the Icon syndicate. The deposit is located on the Waconichici River as the south end of Baie du Poste of Lake Mistassini, approximately 45 miles north of Chibougamau. Property acquisition and Winkie drilling was followed by a diamond drilling program to evaluate the deposit. Stripping of the open pit area connnenced in the late fall of 1966 and the first test sample of ore was shipped to Chibougamau in December of that year.Regular ore shipments to the mill of Merrill Island Mining Corporation Limited for concentration commenced May 25, 1967. Production to December 31, 1970 amounts to 42,960,000 pounds of pay copper.The ore is chalcopyrite in white quartz dolomite, and it contains a very small amount of precious metals. The quartz dolomite assumes a flat to gently dipping attitude and is associated with a graphitic argillite contact zone on both hanging and footwall sides, in dolomitic limestone rocks. There is practically no other sulphide present in the ore.During the summer of 1969 a series of pre-concentration tests were completed and a Wemco heavy media sink float plant was installed in late 1969 and early 1970. This pre-concentrator eliminates at least one third of the ore mined in the form of barren quartz dolomite prior to ore shipment by truck to the concentrator in Chibougamau."

Jan 1, 1971

By James J. Roettger, Robert J. Mitchell

"The results of a series of model stope pours designed to investigate working pressures on bulkheads during hydraulic pouring of classified tailings backfill are reported. Total bulkhead pressures and fill water pressures were monitored under the condition of a fully saturated backfill. Similitude of the model testing is discussed and equations are developed to estimate bulkhead pressures under prototype conditions. The model results show that good base drainage, combined with a bulkhead setback, can reduce the expected bulkhead pressures to values such that timber or concrete block structures should be capable of supporting a saturated backfill. Introduction Bulkheads are used in underground running operations to block drift openings in order that hydraulically placed sand backfill can be contained in stope pours. Whenever possible, the sand fill is designed to have sufficient percolation rate so that excess hydraulic transport water will gravity drain out through the bulk headed drifts. This avoids costly decanting systems. Early bulkhead design assumed that the bulkhead pressure could be as high as 0h = Hy where H is the fill height and ""y is the saturated unit weight of the fill (Thomas et al., 1979)(1). A typical design pressure for a 50 m fill height would be 1250 kPa giving a design force of 12,500 kN on a bulkhead located in a drift of 10m2 in area . Typical bulkheads were 1 m thick heavily reinforced concrete structures formed and poured into a notched drift. Not only were these expensive structures but the associated problems of inside drainage systems and curing time delays increased production costs. As experience with bulkheads for large bulk pours increased and fill pressure measurements became available [see, for examples, Libby et al., 1975(2), Askey et al., 1978(3)] , 'free drainage' timber and concrete block bulkheads were designed. Substantial savings have been realized using these types of bulkheads but greater engineering design and monitoring of backfill pours is necessary to ensure that backfill pressures do not exceed the bulkhead design pressures.The effective and total stress components of fill pressure, the engineering concepts associated with the 'free drainage' design and some detailed design considerations have been discussed by Smith and Mitchell (1982)(4) . It is important to the safe use of these designs, however, that the basic engineering concepts be demonstrated and communicated to those responsible for the day-to-day backfill operations. This paper describes and explains observations from a series of model studies designed to measure bulkhead pressures in a saturated fill."

Jan 1, 1984

By Tao Cheng

Previous research and applications in construction resource optimization have focused on tracking the location of material and equipment. There is a lack of studies on automated monitoring of the interaction between workers and equipment for safety purposes. This paper presents a new approach for measuring the safety performance of construction personnel particularly when they work in very close proximity to moving equipment as well as static hazards such as chemical and flammable substances. A method of generating hazardous zones according to the geometric and kinematic characteristics of the considered hazard is introduced. The spatio-temporal relationships between the hazardous zones and workers? positioning data collected by real-time location sensing technology are automatically analyzed. This approach has been validated in a controlled test bed environment that simulates a construction site. Results indicate that worker?s safety performance of selected activities can be automatically and reliably measured using the developed approach. Furthermore, a heat map is generated for visualizing proximity related issues in the test bed using the computed results.

Aug 1, 2013

By I. Bakry

Uncertainty is an inherent characteristic of construction projects. Neglecting uncertainties associated with different input parameters in the planning stage could well lead to misleading and/or unachievable project schedules. The objective of this paper is to present a new approach towards scheduling repetitive construction projects while accounting for uncertainty. The paper presents an algorithm that quantifies anticipated delays resulting from different sources of uncertainty in the form of fuzzy time buffers. Through inserting the time buffers in strategic places in a time schedule, the algorithm provides protection against those main anticipated delays. The presented algorithm comprises two integrated components, a scheduling component responsible for producing a basic Linear Scheduling Method (LSM) schedule with deterministic activity durations, and a buffer component that handles fuzzy buffers sizing and insertion. The presented algorithm offers four different buffer insertion techniques covering different cases of interrelations between successive activities. The algorithm is implemented in a spreadsheet application, which automates calculations, yet allows users to fine tune the algorithm to fit the project at hand. With a focuses on highway construction projects as an example of repetitive construction projects, this paper accounts for sources of uncertainty such as weather, site conditions, change orders and equipment related delays. A hypothetical case is studied and explained to further demonstrate how the proposed algorithm works.

Aug 1, 2013

By W. H. Hastings

Introductory In the amount of her coal reserves, Saskatchewan ranks third among the provinces of the Dominion, with a total, as estimated by D. B. Dowling, of 59,812,000,000 tons. All the coal so far discovered in the Province is lignite, and it would appear unlikely that bituminous or higher grade coals exist. General Occurrence of the Coal The location of the coal-bearing formations in Saskatchewan is shown on the accompanying map. It will be seen that the areas lie principally in the southern part of the Province. The more darkly shaded areas indicate locations where development is taking place, or where coal-seams are known to occur, either through outcrops in valley-sides or through having been encountered during boring operations. The coal-seams are not necessarily continuous throughout the shaded areas, but in all pans of these there are coal possibilities. It is quite possible that small outliers of the coal-bearing formations may occur further north in the Province, but, generally speaking, coal is not likely to be found outside the shaded areas.

Jan 1, 1929

By Richard Cyr, Peter Larsen, William Quesnel

"The need to continually improve efficiency and lower costs in mining operations is of paramount importance to all concerned in the industry. Mining operations are constantly testing new methods and equipment in order to lower costs and improve productivity. Equipment suppliers strive to fulfill the demands of the mines through improved design and innovative ideas for productivity increases. In some cases, however, an increase in productivity does not require new equipment design, but rather the application of an existing mining method into different operating parameters. Such is the case in applying longhole methods to narrow vein ore deposits.Bulk mining methods have long been recognized as efficient, low-cost alternatives in narrow vein operations. Typically, shrinkage and some cut-and-fill methods are employed. The shortfall of these methods is the tendency to be labour intensive. The demand for miners skilled in these methods far outweighs their availability. Consequently, labour-efficient methods have to be employed to fill the void. The application of longhole drilling techniques to narrow vein deposits is one such method.IntroductionPercussion longhole drilling evolved in Canada in the early 1940s. Prior to percussion drilling, blast holes were drilled using diamond drill equipment. Jack Gardner, of Gardner Steel, began testing with carbide percussion bits and extension drill steel in applications where diamond drills had been previously employed. Percussion drilling equipment proved to be considerably more productive and cost-efficient. The experiment eventually led to the replacement of diamond drills in this application.Over the years, the percussion methods were improved, with particular emphasis on the equipment used. Rifle bar rotation machines evolved to independent rotation. Bar and arm set ups evolved into self-contained mobile drill carriers that increased productivity while reducing the physical labour. The introduction of hydraulics further improved efficiency and production figures. Today, it is not uncommon to see fully computerized jumbos in production longhole drilling applications. These machines represent the ""state-of-the-art"" in longhole drilling equipment.Production longhole drilling is considered to be one of the most efficient bulk mining methods in use today. Production statistics normally exhibit low-cost, efficient ore extraction. As a rule, longhole (blasthole) methods are associated with substantial ore deposits. These methods have exhibited high production figures and low mining costs.Over the past decade, long hole methods have been applied to several narrow vein deposits. These applications have proven that, given the right parameters, longhole methods will produce the same advantages in narrow vein deposits as are seen in more conventional applications."

Jan 1, 1990

By H. M. A. Rice

"The Ainsworth mining camp is on the west side of Kootenay lake; British Columbia; 14 miles south of the town of Kaslo. It is in one of the oldest mining districts in central British Columbia; for mining started there in 1888. Its principal production was between 1905 and 1920. Activity since then has been sporadic. According to available records; some 222; 000 tons of ore had been produced from the camp up to 1942.GENERAL GEOLOGY Bedrock in the district consists of a succession of quartzite, quartz-mica schist, hornblende schist, and limestone of Late Precambrian, Carboniferous, and Triassic age. Most of the hornblende schists are of volcanic origin but some formed from related intrusions. The Nelson granodiorite batholith of Jurassic age borders the camp on the west. There is also a series of basic dykes of much later age."

Jan 1, 1954

By G. Brooks, M. Hamed, S. Nightingale, K. Coley

The Marangoni effect plays a significant role in slag line corrosion of refractories. Previous experimental studies for various refractory /slag systems and mathematical models are reviewed and show that Marangoni flow is important in slag line corrosion under static conditions. Recent work by the authors is presented which also shows significant slag-line corrosion of MgO refractory in SiO2-CaO-FeOx-MgO slag. The rate of attack of the MgO was marginally slower in the case of slags containing alumina. A semi-empirical model developed by Hrma based on mass transfer control described reasonably well the observed progression of corrosion with time. Further work is proposed to evaluate this model.

Jan 1, 2004

By D. A. Trotter

"Low-pressure sodium light sources have been available for several years, but have not received wide acceptance in underground mining. This is because they are difficult to operate using DC power, they are not an intrinsically safe light where explosive gases may be encountered and they give poor colour rendition.With the need for energy conservation, several Canadian hard-rock metal mines are now changing their lighting to low pressure sodium, as it has the highest efficacy of any light source in terms of lumens per watt. Studies have pointed out several other advantages as well. Glare can be controlled, they penetrate fog well, they are easily maintained, they have a long life and they give the highest visual acuity when compared to other types of lighting. As well, in an underground mine, contrast is much more important than colour for task identification. For close work, the colour problem is alleviated with the use of cap lamps.Case studies are presented from Canadian practice. These show how the lights are modified for underground use, calculations preceding light installation, and how and where the lights are installed in the underground environment. Mention is made of worker reaction to the lights and possible physiological effects.IntroductionThe importance of good underground lighting to the total environment of mining cannot be overemphasized. In addition to the obvious benefits of improved worker morale, available studies show that good lighting practices reduce accident severity and frequency as well as increase production."

Jan 1, 1982

By L. D. Smith

"Those who submit competing proposals for projects seek to present senior management with complete and fully supported material that will not fail under questioning. Hopefully, misleading notions and omissions will have been minimized and there will have been testing of the assumptions regarding the economic, social and political environments.A capital project evaluation team can do management and itself a service by including a sound approach to the impact of inflation (and its twin problem, interest) on a project and a great disservice with an inappropriate approach to inflation.InflationHandled deftly, inflation can alter a project evaluation to show almost any result the handler desires. It must be a constant source of frustration for design people and cost estimators to spend weeks perfecting the technical aspects of a project in order to minimize costs, only to have all of their efforts set awash in a sea of financial and economic assumptions that submerge all of the detail. In all of this, inflation is perhaps the largest offender, with inflation criteria often being brought to bear at the last minute, almost as an afterthought. Perhaps this tardiness reflects the difficulty of the subject and the belief that senior management will take its own approach to the problems of inflation. Such a belief is unfair to senior management, for it is entitled to not being misled by omission. It is entitled to the full use of the skills of the evaluating team, including reasonable assumptions of the impact of inflation.Working in a consulting context, one has the opportunity to participate in the evaluation of a large number of projects."

Jan 1, 1990

By Tom Brady

A major focus of ground control research presently being conducted by the Spokane Research Laboratory of the National Institute for Occupational Safety and Health (NIOSH) is to incorporate weak rock masses (such as are associated with operations in the Carlin Trend in Nevada) into existing design relationships. The original database that led to most of the empirical design relationships presently employed in hard-rock mining was derived from fair-to-good-quality rock. In this study, the relationship between weak rock quality and opening design (nonentry/entry methods) is being investigated. The common factor in all mines is a weak back or wall. This work attempts to provide tools that will enable a mine operator to make economic decisions that will also ensure a safe working environment.

May 1, 2003

By T. A. Postolski, A. J. Sinclair

"Abstract- Two examples are used to describe how geological features impact on the development of semi-variogram models to be used for geostatistical resource/reserve estimation of porphyry-type deposits. In the Main zone of the Huckleberry porphyry copper deposit, mineralization is concentrated in fracture zones localized in volcanic rocks, along the eastern and southern margins of a granitic stock. Mineralized volcanic rocks can be subdivided into three separate domains, each with its own preferred direction of mineralization that is reflected in contoured Cu diagrams and semivariograms.The East zone at Huckleberry deposit, spatially distinct from the Main zone, is controlled by a fracture zone elongate roughly east-westerly and bounded on the south by a major fault (easterly striking and steeply dipping) across which there is a dramatic drop in grades. The eastern part of the East zone appears to be coaxial with a large intrusive body; the western part contains a small, elongate dike-like intrusion. Contoured Cu values for many levels suggest that the principal direction of geological elongation of the east and west domains of the East zone differs significantly. Independently derived semi-variogram models for each domain are different and reflect this difference in trend.In both Main and East zones of the Huckleberry deposit, block estimates by ordinary kriging are significantly different using a domain-specific semi-variogram model than using a deposit-general semi-variogram model. The domain-specific estimates are deemed better because they are based on local controls of mineralization and have less conditional bias than those generated by the depositgeneral semi-variogram model."

Jan 1, 1998