Search Documents

By Jim Frazier

Tradition has often dictated low design load stresses on piles. Such traditions often developed prior to modern static or dynamic pile testing methods and perhaps result from a few limiting situations. These low stress limits were then broadly applied, even in cases where the piles could carry substantially higher loads. With sufficient testing to prove the design, higher design loads may present significant overall savings to the project owner. The cost of the testing then becomes an insignificant cost compared to the potentially great benefit of increased pile loadings. To confirm higher load possibilities for driven piles, the pile is tested either statically or dynamically. Further savings and increased testing efficiency result from remote dynamic pile testing. This paper presents a project where design stresses were considerably increased as a result of additional testing and use of remote dynamic pile testing equipment.

Jan 1, 2002

By Lianyang Zhang

For optimal design of rock socketed shafts used to support axial loading, it is important to predict the end bearing capacity. The existing empirical methods for determining the end bearing capacity of rock socketed shafts use the empirical relations between the end bearing capacity, qmax, and the unconfined compressive strength of intact rock, sc. Since rock socketed shafts are supported by the rock mass (both intact rock blocks and discontinuities separating them) not just the intact rock, one should consider not only the intact rock properties but also the influence of discontinuities when determining the end bearing capacity. Although the effect of discontinuities may have been implicitly (partially) included in the empirical relations derived from the results of load tests, it is not clear how big the effect is and how much of it has been included. In this paper, a database consisting of 50 test shafts, 25 of which contain the RQD (rock quality designation) value, is developed. Using the database, the applicability of the existing empirical relations is evaluated and two new empirical relations between the end bearing capacity, qmax, and the unconfined compressive strength of rock mass, scm, are derived. The new empirical relations explicitly consider the effect of discontinuities by using scm which is directly related to RQD. Finally, an example is presented to demonstrate the application of the newly derived relations.

Jan 1, 2008

By Arturo Ressi di Cervia

Construction of the drilled shafts for the Brightman Street Bridge Replacement Project were not only challenging due to working over the water but were also challenged by changed soil conditions, concurrent work being performed by an adjacent contractor on the same project, environmental restrictions and severe winter conditions. A total of 36 x 8 feet diameter drilled shafts with 7.5 feet rock sockets were installed for the East and West bascule piers. This project also included Osterberg Cell load testing on two production drilled shafts at each the East and West bascule piers. The results from the load test program were used to fine tune the design of the drilled shaft rock sockets. From a constructability standpoint the reverse circulation drilling method with a pile top drill rig proved to be an excellent choice for drilling the overburden and rock sockets of the large diameter deep drilled shafts.

Jan 1, 2003

By Jan A. Nilsen

This paper describes a key element in the construction of a major project undertaken by Harbourfront Corporation in its efforts to rejuvenate the central Toronto waterfront. The Spadina Pier forms one of the two major structures of the $10 million marina complex. Completed in early 1986, the 150 metre(490 ft.) long by 43 metre(140 ft.) wide pier structure will contain a 320 car parking garage as well as providing the foundation of a 17-story residential tower and a two-story retail/commercial complex. However, the pier structure posed a considerable challenge to its developers due to the the many restrictions imposed on the site by the environmental authorities which ruled out the construction of dykes or the placing of other fill materials on the highly contaminated bottom sediments. In addition, access at the site was restricted by its proximity to the main harbour navigation channel and a grain elevator berth. The original design called for a cofferdam to form an integral part of the finished structure. However, the contractor chose to regard the cofferdam as a temporary structure and proposed to construct the pier in the dry by enclosing the 10,000 square metre(107,600 sf) site with a 450 metre(1480 ft.) long single wall steel sheet pile cofferdom 7.5 metres(25 ft.) from the final pier structure. This paper will describes the design and construction of the cofferdam. Prior to finalizing the pier design, a geotechnical investigation of the shale bedrock was undertaken as well as a small sheet pile test cell program to evaluate the feasibility of driving a Canadian manufactured cold-rolled sheet pile into the bedrock. Relying on the design parameters for the shale bedrock, Foundation designed the cofferdam utilizing a post-tensioned bipod bracing system to resist a 7 metre(23 ft.) hydrostatic head as well as the maximum wind and wave forces expected at the site. The bipod bracing system consists of diagonal H-pile raker piles and verticle pipe piles anchored to bedrock with post-tensioned anchors grouted into bedrock.

Jan 1, 1987

By Sikko Doornbos

For the extension of the Paper Mill of Parenco in Renkum, the Netherlands, the application of a pile foundation was required. The demands for this pile foundation were very explicit a vibration free and soil displacing pile systems with low allowable settlement. Another important aspect was the total amount of piles (originally over 1600 auger piles) which had to be executed within 3 months, in very difficult and unhomogeneous soil. Based upon these conditions the Tubex Grout Injection Pile was chosen to be used for this project. This system involves the drilling of a steel tube with a conical pile shoe while grout is injected at the point simultaneously, creating a mixed-in-place layer around the tube. INTRODUCTION After extensive marketing, the board of directors of Parenco, decided to a large extension of the production capacity of its paper mill by building a new production building called Paper Mill 1 or PM-1. The new PM-1 extension had to be constructed beside the existing PM-2 because of limited terrain. The site is located right between the Rhine river and Renkum, approximately 15 kilometers (10 miles) west from Arnhem (see figure 1). The construction involved the building of the PM-1 extension of approximately 250 meters (820 ft.) long by 40-60 metres wide (130-200 ft.). The main structure was to be constructed of precast concrete beams and columns.

Jan 1, 1987

By Matteo Montesi

Deep foundation elements are often used as discrete elements in externally supported earth retaining structures such as soldier piles and lagging walls, secant/tangent pile walls, anchored walls, etc. These structures can be designed using different approaches such as conventional limit equilibrium methods, finite element/difference analyses, and soil spring (p-y) analyses which are contained in various commercially available computer programs used by engineers worldwide. Although these programs usually undergo various degree of verification and validation, users must be aware of each program’s limitations and conditions in which each design approach should or should not be used. These programs may incur difficulties when non-continuous deep foundation elements are used as part of the retaining system and in cases of non-uniform geometry where closed-form solutions are not available. Design input parameters such as passive arching width, wall-to-soil friction, and p-multipliers (pm) are not always given enough attention which may result in potential design deficiencies. This paper presents the main features of various earth retaining structure design approaches and discusses their advantages/disadvantages. The paper addresses some of the limitations and difficulties that may be faced with when utilizing non-continuous discrete deep foundation elements and identifies key elements that are sources of potential deficiencies and errors. An example comparing the design outcomes using different design approaches is presented. INTRODUCTION Earth retaining structures are used to retain soil and create or maintain a difference in ground elevation between grades in front and behind the retaining structure. Deep foundation elements have been used for decades to support earth retaining structures. Earth retaining structures that are supported by deep foundation elements are typically referred to as externally stabilized system (O’Rourke and Jones, 1990). An externally stabilized system uses an external structural element, in contrast to internally stabilized systems which rely on reinforcements installed within and extending beyond the potential failure mass. The design of externally supported retaining structures can be accomplished using different approaches, which can be challenging under certain conditions. Each approach has been discussed extensively in available literature, and is well summarized in the and Federal Highway Administration (FHWA) guidelines. The objective of this paper is to present the most widely used design approaches and discuss their limitations and difficulties in one concise and brief document, giving the reader a good source for comprehensive understanding of the various design approaches, supported by a technical example. This paper is not intended to be a comprehensive review of all available design methods and formulations available in the literature.

Jan 1, 2018

By Franklin M. Grynkewicz

The subject of bearing pile performance installed by vibratory hammers has been a matter of increasing study and continued controversy. A recent case study from a major bridge replacement project is discussed which provides encouraging data on the use of vibratory pile hammers as a primary means of pile installation and also presents the problems associated with its general acceptance. The bridge project case study foundations consisted of HP 14 x 89 pile sections, designed to develop capacity primarily in friction. Preliminary tip elevations were determined by traditional static analyses. Production pile installation was performed using an IHC S-70 Hydro-Hammer. Driving criteria and final production pile tip elevations were determined after preliminary indicator pile drive tests and static load test results at bridge pier cofferdam locations. Based on impact driven production pile performance, the Contractor wished to investigate vibratory driven piles as a means to accelerate construction schedule. Dynamic pile testing procedures were used as the primary measurement tool and test results were compared to the production pile drive records and prior static load tests. Field testing consisted of driving and monitoring with the PDA impact driven piles to the design tip elevation. Three vibratory driven piles were installed to the same tip elevation and immediately subjected to impact driving and dynamic testing to compare dynamic pile resistance. The results indicated that the site soil conditions were favorable for vibratory pile hammer installation. Recommendations and procedures for proceeding with vibratory hammer pile installation were presented to the Owner. These procedures included quality control in conformance with latest AASHTO recommendations. The Owner, in spite of the site specific data base and QA/QC procedures, would not accept vibratory pile hammer installation, due to the absence of precedence. It is concluded that for vibratory methods to become accepted a rational method of analysis, design and field QA/QC procedures requires development. In addition, the engineering community and Owners/Agencies must be more open to alternate methods of foundation construction. The continued development of dynamic methods of monitoring vibratory pile installation is considered to be key to the general acceptance of this installation procedure.

Jan 1, 1991

By Sanket Rawat, Ravi Kant Mittal, Vikash Prasad

"The understanding of the response of pile foundations under various types of loads is a necessary prerequisite to analyze and design them properly. Therefore, this paper highlights and compares the provisions available in Indian Standard IS 2911:2010 to estimate the capacity of laterally loaded pile foundation with the provisions available in different country codes and existing literature. Comparisons are made between the Indian standard method, Broms method and Matlock & Reese method for the analysis of laterally loaded piles due to popularity and prevalence of the later methods in design offices worldwide. This has been achieved using a parametric study on pile embedded in pre-consolidated clay and sand for both fixed head and free head case in terms of displacement and ultimate load capacity. It has been found that there are various limitations to the Indian Standard method associated with various cases such as short pile analysis, complete moment distribution etc. Therefore, suitable recommendations have been made on the basis of the above comparison to improve the accuracy of the design in Indian perspective. The proposed comparison and subsequent area of improvements will present the design engineers all across the globe, a broad sight of design specifications of laterally loaded piles.INTRODUCTIONPiles in groups are very often subjected to both axial and lateral loads. In the 1960’s, designers used to assume that the piles could carry only axial loads and the lateral load is to be carried by batter piles. However, later, a large number of load tests authenticated that vertical piles also can transfer lateral loads through shear, bending, and lateral soil resistance rather than purely acting as axially loaded members. Initial attempts to analyze laterally loaded piles used the finite-difference method, as described by Howe (1955), Matlock and Reese (1960), and Bowles (1968). Matlock and Reese (1956) used the finite difference method to get a series of non-dimensional curves to enable the user to input the appropriate curve with the given lateral load and estimate the ground-line deflection and maximum bending moment in the pile shaft. Later, Matlock and Reese (1960) extended the earlier curves to include selected variations of soil modulus with depth."

Jan 1, 2017

By Abolfazl Eslami, Masoud Zare, Ali Asadi, Ali Abrang

"Physical small scale models for study of deep foundations can be performed in simple chambers (1g), calibration chambers (CC), and centrifuge apparatus (ng) which involve some limitations and difficulties. In recent years, Frustum confining vessels (FCV) have been developed for physical modeling of deep foundations. This device is frustum of a cone shape that applies a steady pressure on its bottom and creates a linear stress distribution along its vertical central line. A new FCV which has been built in AUT is introduced. This device has a height of 1200 mm, top and bottom diameters of 300 and 1300 mm, respectively. Through the application of bottom pressure up to 300 kPa, the insitu overburden stress conditions equivalent up to 40 m soil deposits consistent to the embedment depth of commonly used piles. Observation indicated that there is approximately a linear trend of stress distribution, and this device can create realistic overburden stress in the desired control volume along the central line. Moreover, a couple of compressive and tensile load tests were performed on steel tubular open end model piles driven in sand with length of 750 mm and different diameters and L/D ratio between 8-15. Comparison of load capacity between tested and full scale piles demonstrate a suitable conformity for similar confinement conditions. Therefore, the FCV can be realized as an appropriate apparatus for investigation of piling geotechnical behavior and examination of construction effects.IntroductionDeep foundations are designed as foundation system for supporting heavy loads, high rise and important structures. Different theoretical, numerical and experimental approaches have been developed to study the geotechnical behavior of deep foundations. Experimental methods are employed to clarify directly pile-soil interaction and because of repeatability, analogy, rapid measurement and cost efficiency, physical modeling can be realized as an intermediate technique compared to element testing and full scale load tests."

Jan 1, 2015

By Walter G. Kutschke

Four significant soil nail wall projects in the eastern United States were recently completed with a combined area of 175,000 square feet of finished shotcrete surface. These projects required the use of innovative design and construction methods in order to address various challenges, including slide-prone back slope materials, perched water, highly erodible rock materials, curved wall alignments, very tight construction tolerances and unexpected subsurface conditions. Special focus is given to issues such as bench excavation, soil nail installation methods, shotcrete mix design, anticipated shotcrete quantities, shotcrete nozzlemen qualifications and weather conditions, in order to provide a lessons-learned database for future soil nail wall design and inspector considerations. These projects also underscore the importance of design engineer and soil nail wall contractor qualifications as well as effective communication with the owner.

Jan 1, 2007

By Timothy J. Myers

Expansion and the economic growth in the southwestern region of Missouri necessitated the expansion of State Route 249 and the construction of a new interchange to provide service to the Joplin, Missouri area. The project is located above a former lead and zinc mine in Jasper County, Missouri and includes a five bridge interchange connecting State Route 249 and US Route 171. The variable subsurface conditions, both natural and manmade, prompted the design team to use ground improvement via grouting and small diameter micropiles to provide support for several of the bridge foundations on the project. The scope of work included mine shaft closures, 56,000 ft of overburden and rock drilling, 11,139 ft of micropiles, 524 cy of balanced/stabilized high mobility grouts, and over 8,700 cy of low mobility grout. The selection of the grout used was based on the actual subsurface conditions. Low mobility grout (LMG) was used in voided conditions and for closure of the mine shafts encountered during the excavation. High mobility grout (HMG) was used in fractured rock with the goal of improving the mechanical properties of the rock underneath the future bridge footings and controlling grout volumes during micropile installation. The split spacing method was utilized for both LMG and HMG holes. Geology of the project site subsurface consisted of extremely variable bedrock with strong to very strong limestone, chert, breccia, extremely weak shale, and weak to strong sandstone. Previous activities associated with the mining disturbance (such as partial filled vertical mine shafts, shallow and deep mine horizons, modified hydrology including artesian conditions) further complicates the site subsurface conditions. Real time monitoring and recording of all drilling and grouting parameters was conducted to assist in the evaluation of in-situ geological properties of the site in order to modify the ground improvement and micropile program as necessary. This paper will discuss the design and execution of the ground improvement and micropile program. The project is an excellent example of the use of multiple ground improvement and foundation support techniques combined with real time data analysis to provide a foundation support solution for a complex geological environment.

Jan 1, 2009

By Osama Safaqah

The new Cooper River Bridge will replace two existing bridges along U.S. Highway 17. The cable-stayed bridge will be one of the largest in the U.S and will connect the City of Charleston and the town of Mount Pleasant, South Carolina. The 1,546-foot long main span over Cooper River is supported by two diamond-shaped towers and will allow for 1000-foot wide navigation channel. The Charleston high-level approach is approximately 4351-foot long and will provide 250-foot wide navigation channel over Town Creek, while the Mount Pleasant high-level approach is 2090-foot long. Due to the high seismicity in the region, potential vessel impact, and hurricanes, large lateral loads are expected. Among various types of foundations, 10-foot diameter drilled shafts were selected for their high capacity against lateral loading. The shafts are founded on a stiff to very stiff lightly cemented calcareous sandy clay or sandy silt layer, called Cooper Marl, which underlies coastal sediments of interbedded clays and sands. The main towers will be supported on a group of 11 shafts and protected from ship collision by a rock island. The High Level Approach piers will be supported on a pair of 2 shafts. The shaft tip elevation is up to 230 feet below water line. An elaborate geotechnical investigation has been conducted on the site including a load test program on full-scale shafts under axial and lateral loads. The results of the tests were used to calibrate the lateral and axial soil resistance. The objective of this paper is to present the different aspects of the bridge foundation design.

Jan 1, 2005

By E. Naesgaard, Brian E. Hall, A. Amini, Advanced Geosolutions, A. Azizian

"A 2 km section of the Evergreen Line Rapid Transit Project is supported on improved ground consisting of cement deep soil mix (CDSM) panels because of highly variable and challenging soil conditions, especially the potential for seismic liquefaction-induced lateral spreading. CDSM was used as an alternative approach in place of driven piles for reducing the seismic lateral spreading displacements. An additional significant aspect of obtaining owner acceptance for CDSM was demonstrating that both seismic and non-seismic performance would equal or exceed that of using driven piles. It was recognized that, to demonstrate adherence to the seismic performance requirements, seismic design should be based on dynamic analyses (using FLAC) to estimate likely displacements and stresses/strains in the CDSM panels. One focus of the analyses was investigating the potential for cracking of the CDSM panels and the resulting displacements. This was simulated using the Ubiquitous-Joint and UBCSAND constitutive models.INTRODUCTIONThe Evergreen Line Rapid Transit Project (ELRT) is an 11 km extension of the SkyTrain system through Burnaby, Coquitlam and Port Moody in the Lower Mainland of British Columbia, Canada (Figure 1). The ELRT project is being delivered through a Design/Build/Finance model by Evergreen Rapid Transit Construction (EGRT), an SNC-Lavalin Inc. company, to the Province of British Columbia (the Province).This paper discusses the ground improvement design for a 2 km section of the alignment through Port Moody, a historic city at the head of Burrard Inlet. The alignment is located in a right-of-way of restricted width with many pinch points close to residential and commercial properties, and directly adjacent to the Canadian Pacific Railway (CPR) mainline tracks. The ground slopes from south to north across the alignment towards Burrard Inlet at inclinations of up to about 6%. Design and construction of the Port Moody section was subcontracted to SNC-Lavalin Constructors (Western) Inc. (SLCW) and SNCLavalin/ Graham Construction Joint Venture (SGJV). Construction included single- and double-track slab guideways, pocket track (where up to four to six tracks were present), and Moody Centre Station."

Jan 1, 2015

By Haijian Shi, Drew Pizzo

This article focuses on the appropriate application of subsurface investigation methods for transmission structures, which are typically designed to resist lateral rather than vertical loads. Currently, the three methods used most often for the subsurface investigation of transmission structures in the field are the Standard Penetration Test (SPT), the Cone Penetration Test (CPT), and the Flat Dilatometer Test (DMT). Each of these methods has advantages and disadvantages, and each is more applicable to some scenarios than to others. To gain a better understanding of these test methods and the implications of using them for various kinds of applications, a comparison study was conducted in the field in Maryland, for three boring locations. Each boring location was explored using each of the three tests as stated. The results of the tests and lessons learned are presented and compared, and these comparisons show that the three test methods agree on the majority of the findings. The results from each test method were also used to derive key parameters such as the soil friction angle for given foundation designs considered in order to establish a clear basis for comparison. Recommendations for performing transmission structure subsurface investigations are made in order to optimize the use of each method and thereby optimizing subsequent foundation designs. INTRODUCTION For overhead transmission structures, the most important structural requirement for determining the foundation design differs from the requirement for other structures such as buildings and bridges in accord with the conditions the transmission structures will need to withstand. In addition to the ability to bear a given vertical load consistent with its use, the foundation must bear lateral loads arising from wind and other weather conditions. The foundation types used most often for overhead transmission monopole structures include concrete drilled pier, vibratory caisson, and direct embedment. In order to determine an appropriate and even an optimum foundation design for any given set of conditions, an appropriate subsurface investigation method or approach is needed. Currently, the standard penetration test (SPT), the cone penetration test (CPT), and the flat dilatometer test (DMT) are the three most commonly used subsurface investigation methods.

Jan 1, 2018

By Patrick J. Hannigan

The pile foundation designer typically performs a subsurface exploration program and static pile capacity calculations before selecting a pile foundation type, length, and capacity. During construction, a pile installation criterion must be established to meet these design requirements. This installation criterion usually consists of a minimum penetration resistance or blow count to confirm pile capacity and may also include a minimum embedment requirement. This text will focus on use of wave equation analysis and dynamic measurements to meet design requirements. BEFORE THE WAVE EQUATION Since the mid-1800s, over 450 dynamic formulas for pile driving control have proliferated. In their simplest form, these formulas relate hammer energy to the work of soil resistance, or simply: W ? h = R ? s (1) Where W = ram weight h = ram drop height or stroke R = pile capacity s = pile penetration per blow

Jan 1, 1990

By S. Hardy

The paper describes state of the art non-linear analyses of the pile groups that were employed during the raising of the 133m high triumphal arch which forms the centre piece of the new Wembley stadium in North London. The deformation behaviour of these piles groups was critical during the lifting process, due to the slendemess of the arch structure. The issue was made more critical by the high profile nature of the project. The results of Class A (Lambe (1973)) predictions of the pile group movements are compared with observed displacements and rotations which were accurately measured on site. To illustrate the importance of soil non-linearity on pile group behaviour, comparison is also made with pile group analyses which assume a linear soil stiffness.

Jan 1, 2006

By Tom Szynakiewicz

Micropiles are routinely used in the United States for foundation support and underpinning applications. The high capacities achievable with the use of micropiles, combined with specialty rigs for easy installation in low headroom and difficult access areas makes them a good choice for situations often encountered on existing commercial projects. The bond zone of the pile is typically drilled into a competent stratum such as sands, gravels or bedrock. In this paper, the authors will discuss a project where the lack of a shallow ?competent stratum? led the geotechnical contractor to create their own bond zone for the micropiles using jet grouting. Due to problematic clay (CH) soils, the original foundation of a six story office building in west Houston had experienced up to five inches of differential movement in-between the shallow under-reamed shafts. The owner desired a permanent solution to the problem without disturbing the majority of the tenants. The structure was underpinned with a hybrid system of jet grouted micropiles as well as jet grouting alone and the structure was re-leveled using hydraulic equipment to within a 0.25? tolerance. Design, construction and sequencing of the project are discussed in the paper. QA/QC methods are also discussed, including coring for verification of jet grout column diameter as well as a full-scale micropile compressive load test. The structure was successfully re-leveled and the entire project was completed without disturbing any tenants on the floors two through six.

Jan 1, 2008

The intent of this manual is to provide guidelines for inspectors of drilled shaft construction otherwise referred to as drilled piers, caissons or bored piles. It should also be helpful to train beginning geotechnical engineers with limited first hand experience or for geotechnical engineers who are training inspectors. It is expected that the general guidelines and procedures described here will be supplemented by local geotechnical engineers working in a particular region based on local practice and experience. Since drilled shaft construction procedures vary widely based on local geology and size of project, an all-inclusive manual is not considered practical. This manual focuses on traditional topside inspection for routine drilled shaft construction. Other inspection and evaluation methods that rely on electronic equipment are available, but these methods require extensive training and experience in the interpretation of results. These more sophisticated methods of drilled shaft inspection and evaluation are common in construction, but they are usually provided by specialty subconsultants. The subconsultant will typically submit a report for each shaft, which will be reviewed by the geotechnical engineer. Other manuals are available to describe the electronic methods of drilled shaft inspection.

Jan 1, 2004

By Jon H. Gould

This paper describes the following at the new Advanced Solid Rocket Motor (ASRM) nozzle manufacturing facility, which is being constructed inside an existing manufacturing facility: 1) generalized subsurface conditions, 2) pile load test program and evaluation, 3) pile selection, 4) problems associated with pile driving operations, and 5) production pile installation. The poor subsurface conditions, known and unknown underground obstructions, and work environment inside the existing building, used to manufacture the Space Shuttle external fuel tanks, required special pile installation equipment, procedures, and work schedules to install the economical pile foundation system ahead of schedule and without a lost time accident. GEOTECHNICAL STUDIES In April and May 1990, 16 soil test borings were drilled inside the existing building with a truck-mounted drill rig. The borings extended to depths ranging from 60 to 65 ft (18.3 to 19.8 m) below the floor slab. Typically, the silty and clayey soils were sampled by pushing "undisturbed" Shelby tubes, and the more sandy soils were sampled by driving a Standard Penetration Test (SPT) split-spoon sampler. The unconfined compressive strength, water content, and unit weight of the Shelby tube samples were measured in the laboratory. A geotechnical report was issued in May 1990 presenting the results of the field and laboratory testing and foundation recommendations (Gilbert, 1990).

Jan 1, 1992

By Frances Badelow

This paper describes a design process for piled raft foundations supporting high-rise buildings. The design process comprises an initial stage of geotechnical site characterization using the results of investigation boreholes to prepare a subsurface model and derive geotechnical parameters for raft and pile design from empirical correlations. Following this a preliminary analysis is undertaken using a combination of elastic theory and allowances for non linear behaviour of the piled raft system to assess the viability of such a foundation system and any potential advantages of a piled raft over conventional fully piled foundation systems. Finally, a detailed analysis is undertaken using the GARP8 computer program. Case studies where this design process has been successfully used to design a more efficient piled raft system that has resulted in significant cost and time savings compared to conventional bored pile foundation options are also described.

Jan 1, 2006