Search Documents

By Edward A. Barrett, Roberta A. Calhoun

MORE THAN 30 MILLION EMPLOYEES each year are exposed to hazardous occupational noise, and approximately one-third of them develop permanent hearing loss (NSC, 2000). Possible explanations for the latter statistic include worker regard for noise as a mere nuisance rather than as an occupational safety and health hazard, and consequent neglect of established protective measures (e.g., hearing protection); lack of knowledge concerning noise; improper use of hearing protection; worker indifference; and inadequate training (Bauer & Babich, 2004). Many drill rigs generate high sound levels, which vary according to the type of machine, its location with respect to the physical surroundings, and the location of the sound measured around the rig. A NIOSH study measured noise output from several types of drill rigs during field investigations (Ingram & Matetic, 2003). Two types of data were recorded the actual noise generated by the drill rig at various positions around the rig and the noise to which the drill operator was exposed during the drilling cycle. For the latter, sound level measurements up to 120 dBA were recorded while hammering casing (metal on metal) in drilling a water well (Photo 1). Several types of administrative controls exist to address worker exposure to loud drill rig noise. Rotating duties to decrease exposure time and posting warning signs in high-noise work areas are two such controls. Another is the use of hearing protection. Worker use of hearing protection has been disappointing, however. One study by the University of Michigan found that construction workers used earplugs and earmuffs only between 36% and 61% of the time that they were necessary (Lusk & Kerr, 1998). In a 2001 study, OSHA reported a relatively low rate of 30.4% for use of earplugs among construction workers (Walker, 2001). Why are rates for hearing protection use so low? One explanation may be workers' lack of concern for noise in the workplace. They expect workplace noise to be a loud and in¬ evitable nuisance and, therefore, accept it as part of the job. As a result, they disregard proven measures that can protect their hearing. Other workers may use hearing protection, but do so improperly. They may misguidedly remain in high-noise areas for extended periods thinking they are protected when in fact they are not. Other reasons for low use and/or misuse of hearing protection include poor education, lack of awareness and inadequate training (Nash, 2003). To address the training issue, NIOSH developed two exercises from which drillers can learn about noise, hearing loss and hearing protection. The first is an invisible ink exercise, titled "Drill Rig Incident" (DRI) (Photo 2); the second is a 3-D slide reel training aid, "Wearing Hearing Protection Properly" (WHPP) (Photo 3). DRI is an instructor-

By William M. Hinton

This report describes the approach, procedures, and results of a program to develop training materials for roof bolter operators. The objective of the program was to design and produce a training sequence which would prepare roof bolter trainees for job performance. Data was collected and analyzed using the general procedures of Instructional Systems Development (ISD). Input data came from a previous roof bolter training analysis program. This data was expanded and structured through a series of ISD steps: objectives hierarchies, media selection, syllabus, lesson specifications, and train¬ing materials development. The resulting program consisted of an ordered sequence of 15 lessons. The media mix for the 15 lessons included lectures, slide-tape lessons, and hands-on instruction using operational roof bolters. Contents of all lessons were reviewed and approved by the Bureau. The key recommendations were to (1) validate the materials and measure relative effectiveness of media formats; (2) survey mines for training resources and conditions - match materials to user capabilities, rather than selection state of the art technology/media; (3) develop job performance aids (JPAs) rather than simulators; (4) create a style/media/JPA development guide for use in future projects of this kind.

Jan 1, 1982

By Edmund S. Leaver

[In previous reports5/ of ore-testing studies standard methods of conducting; test with precious-metal ores selected as representative of certain mining districts were discussed in considerable detail. In addition to standard tent procedures such as direct cyanidation, amalgamation, gravity concentration, and flotation, or a combination of these methods, it is sometimes necessary to apply other methods, such as preliminary roasting and washing of the calcine with plain or acidulated water before cyanidation. In all of this work standard tenting procedure has been supplements by he necessary assaying and analyses of original ore and test products.]

Jan 1, 1941

By Ronald Branstetter

Gaseous and particulate exhaust emissions from 20 diesel engines in service at five underground mines were measured with high accuracy instrumentation. The engines that were tested were checked for faults or maladjustments. The vehicle and engine maintenance organization was studied at each mine and an idealized maintenance program was devised. Faults were induced in a new diesel engine to determine their effect on the characteristics of the exhaust emissions. The results, conclusions and recommendations from this investigation are presented in this final report.

Jan 1, 1983

By H. R. Babitzke

The purpose of this investigation was to develop an alloy of columbium for use at high temperatures and for nuclear applications. The properties of possible alloys were determined, and the more promising ones were selected for further improvement. Criteria for selection were machinability, hardness, workability, tensile strength, and oxidation resistance. Thirteen 100-gram ingots, ranging from 100 percent columbium to 100 percent vanadium, were prepared and subjected to various tests. Also included for comparison were zirconium and the zirconium alloy, zircaloy-2. Test results showed that a columbium alloy, containing 10 atomic percent vanadium merits further development. Besides being workable at room temperature, the columbium-10 atomic percent vanadium alloy has oxidation resistance superior to the other alloys of the series and is also superior to zirconium or zircaloy-2. The latter two materials have comparable neutron-absorption cross sections. The strength and hardness values of the alloys tested were found to increase with increasing vanadium content, reaching a maximum at 50 atomic percent vanadium and decreasing with further increase in vanadium. This behavior is typical of binary alloys wherein each element will retain any proportion of the other in solid solution. INTRODUCTION There is an increasing need for alloys for service at high temperatures. Since current world reserves of columbium metal approximate 1,500,000 tons (1),4 this metal is now readily available. Columbium can ties; be considered a practical base material for high-temperature alloys required in nuclear reactors and in aircraft and space vehicles. General requirements chosen are: (1) Workability, (2) satisfactory mechanical properties at temperatures approaching 1,000° C., and (3) resistance to oxidation at such temperatures.

Jan 1, 1962

By S. Kraemer

Consumption of plastics has been growing in both the U.S. and world markets since the mid-1930s. This growth is due to plastics being used to make new products and as a replacement material for existing products. This paper develops an understanding of the replacement process by looking at the use of plastic, specifically PVC, in the construction pipe industry. History details the growth of the plastics industry and a discussion of the material selection process indicates the advantages and disadvantages of plastic pipe. Analysis shows that the use of plastic, as an alternative material for pipe, is having a significant effect on the cast iron, copper, clay, and steel industries. For the purpose of understanding the replacement process, three example residential systems were examined with a lifecycle cost analysis being performed. PVC was the material of choice in 1988 for all systems. Even though disposal cost was the one area where PVC was not the most cost effective, disposal costs were not sufficient to offset the overall advantage of using PVC on an economic basis. That plastic competes effectively with other materials, in terms of material properties and cost, indicates that further work should be performed to understand the impact plastics have on other material markets.

Jan 1, 1991

By H. M. Thorne

The Petroleum Experiment Station of the Bureau of Mines at Laramie, Wyo., in cooperation with the University of Wyoming, has in progress chemical and refining studies of Wyoming black oils. In general, these crude oils are characterized by their high sulphur, high asphalt, and low gasoline content and are called black oils because of these properties and their color. Characteristics of the various Wyoming black crude oils, as determined by the Bureau of Mines Hempel method of analysis, have been published.4/

Jan 1, 1938

By D. E. Shanks

This U.S. Bureau of Mines (USBM) research simplified an earlier hydrogen chloride (HCI) leach-sparge process developed by the USBM to recover reduction-grade alumina from domestic kaolin clay. Improvements were made by decreasing the initial leaching acid concentration from 25 to 20 pet, decreasing the leaching time from 1 to 2 h to 15 to 30 min, eliminating the solvent extraction step for Fe removal, and eliminating the step to recover the AI content of the bleedstream circuit. A 10-cycle bench-scale experiment of the simplified process showed that the ferric chloride (FeC13) concentration built up to 9.3 g/L in the recycle stream. This did not interfere with any of the unit operations or final alumina product purity because Fe forms stable soluble chloride complexes when sparged with HCI and is easily washed from the large aluminum chloride hexahydrate (ACH) crystals. The reduced leaching time and acid concentration did not decrease Al extraction.

Jan 1, 2010

By E. L. Singleton

The electrochemical reduction of aluminum chloride to aluminum was investigated in a closed, two-compartment cell utilizing a molten chloride electrolyte. The externally heated cell was divided into a reduction compartment and a combination AICl3 feed and metal removal compartment. Aluminum was deposited at 700° C on a molten aluminum catbode from a KCI-NaCI-AICI3 electrolyte. The AICl3 content of the electrolyte was replenished by either vapor or solid additions. The chlorine evolved was collected and measured to give a quantitative evaluation of AICl3 reduction. The effects of anode and cathode current densities and AIC13 concentration on anode current efficiencies were studiedo A range of 64 to 84 percent anode current efficiency was obtained with the 25-pound electrolyte capacity cell and related auxiliary equipment.

Jan 1, 1968

By H. M. Thorne

The Petroleum Experiment Station of the Bureau of Mines at Laramie, Wyo., in cooperation with the University of Wyoming, has in progress chemical and refining studies of Wyoming black oils. In general, these crude oils are characterized by their high sulphur, high asphalt, and low gasoline content and are called black oils because of these properties and their color. Characteristics of the various Wyoming black crude oils, as determined by the Bureau of Mines Hempel method of analysis, have been pubished.4/

Jan 1, 1938

By J. Mitchell Linnet

Bureau of Mines personnel examined mines, prospects, and mineralized areas to determine the mineral resources and potential of deposits in the Bucks Lake and Chips Creek RARE II areas in Plumas and Butte Counties, California. These areas lie along the west slope of the Sierra Nevada on opposite sides of the North Fork Feather River and encompass an area of 62,800 acres (25,400 ha). Metasedimentary and metavolcanic rocks of the Pennsylvanian Calaveras Formation are intruded by plutons of Mesozoic age. Mineral; of economic iterest are in quartz veins in metasediments close to these plutons; they are principally gold and silver with minor amounts of copper, lead, and zinc minerals. Molybdenum, copper, silver, and tungsten minerals occur in tactite along metasedimentary-granitic rock contacts. In both areas, auriferous Tertiary channel gravels have been extensively developed. Asbestos occurs in ultramafic rocks in both areas, and a limestone deposit was explored in the Chips Creek area. Gold is the principal economic mineral in the Bucks Lake RARE II area. The Shenandoah Mine (fig. 1, no. 19) contains 7,500 tons (6,800 t) of indicated and inferred subeconomic gold resources in sulfide-bearing, silicified metamorphic rocks of the Calaveras Formation (table 1). Similar rocks have yielded gold at the Edman and Megowen Mines, adjacent to the area. A high potential exists for additional lode resources in the area around the Shenandoah Mine. Callahan Mining Corporation personnel believe a multi-million ton disseminated gold deposit underlies the property.

Jan 1, 1983

By Tuncel M. Yegulalp

This final report contains the results of all work performed under BOM Grant J0333905. A preliminary systems analysis of coarse-particle coal slurry pipelines as a haulage method for longwall mining systems was performed. Two exhaustive literature surveys on state-of-the-art longwall mining and slurry transport technologies were prepared. Two representative longwall systems were designed, one with conventional haulage and one with slurry haulage. These two systems were then compared on the bases of cost, safety, and reliability. The conclusions were that for the case of a two-face longwall mine, a coarse slurry transport system does not have a clear-cut cost advantage over a conventional (conveyor-hoist) system. However, indications were that a cost advantage could occur under different analytical conditions such as: (1) a larger scale mine, (2) if intangible benefits were quantified, and (3) if new generation technology rather than currently available technology were applied to the study. Budget and time constraints prevented exploration of these conditions.

Jan 1, 1982

By Linneas W. Laage

MFIRE is a computer simulation program that performs normal ventilation network planning calculations, and dynamic transient state simulation of ventilation networks under a variety of conditions. The program is useful for the analysis of ventilation networks under thermal and mechanical influence. MFIRE simulates a mine's ventilation system and its response to altered ventilation parameters, external influences such as temperatures, and internal influences such as fires. Extensive output enables detailed quantitative analysis of the effects of the proposed alteration to the ventilation system Network simulation using digital computers has become widespread throughout the mining industry in recent years. However, as the sophistication of the simulator increases (MFIRE, for example), the complexity of input data requirements and interpretations of results requires more skill and knowledge from the users. Perhaps the most difficult part of using MFIRE is to construct the data set describing the mine's physical layout and its ventilation properties. The initial attempts to get the data set running often reveal unknown or ignored aspects of the mine's ventilation.

Jan 1, 1995

By Herman O. Ankenbruck

Analyses of statistical data indicate that haulage accidents are one of the largest sources of injuries and fatalities in underground coal mines, and that the rate of accidents in transportation has been increasing during the past few years. These previous analyses were performed by correlating accident or fatality data at a rather high level of miner activity. In this present investigation, underground surveys were made by observing conditions and activities in some detail at a rather low level of activity in an attempt to understand factors contributing to hazards in the specific situations observed. The aim of the current study was to derive preventive measures that might obviate the hazardous conditions and unsafe acts observed; and, following this, to provide recommendations for additional research and development to reduce accident potential in underground transportation. The major project tasks are diagrammed together with the task outputs in figure 1-1. Initially, a preliminary study of ell underground haulage operations was performed in order to establish the kinds of data needed and to provide the rationale leading to the data requirement. At the same time, the various types of haulage equipment used for each operation were defined. A preliminary analysis of each type of haulage operation was performed in order to establish the sequence of tasks required to operate haulage equipment. These tasks were transferred directly onto observation forms, and were used in developing interview forms. In parallel with the task analysis, a review was made of accidents and hazards that might occur during each type of operation.

Jan 1, 1975

By M. M. Gilkey

This report describes the effects of water shortage on Arizona's mineral industries. The information presented was obtained in interviews with company representatives. Operations covered included all State metal mines using substantial quantities of water and all concentrators and smelters. Also included in the survey were 8 operations in the nonmetallic group; 22 in the plating, metal-fabricating, and metal-forming categories; 1 public-utility power company; and 6 water companies. The extent of the water shortage in Arizona is reflected in mineral- industry water-use practices, in the high cost and low quality of water used at many operations, and in the stringency of State control of well drilling and pumping. Many mineral-industry operations are among those users most seriously affected by the uneven water supply.

Jan 1, 1963

This volume contains a series of papers describing research conducted by the Bureau of Mines to develop or improve equipment and systems that satisfy the communication requirements of miners doing work related to rail, belt-conveyor, trackless, and hoist haulage systems.

Jan 1, 1977

By A. W. Ambrose

"Introduction.Oil-field operations have often been carried on under great stress and haste, in which the prime purpose has been to put the wells down rapidly as possible, without regard to a few of the various factors affecting cost. In such fields as Burkurnett, Texas, where the well locations are town lots and other small tracts, the operator was concerned primarily with in drilling. In such cases a few thousand dollars more or less in the cost of a well not considered. We are reaching a time, however, when our reserves a,more definitely outlined and properties are being along more economic lines. Operators are becoming more concerned with the actual cost of this work, and are gradually learning that fuel consumption can be reduced in drilling and producing without delaying the speed of drilling, and in the case of production, it will greatly reduce the unit cost per barrel of production.Types of Field Boilers.In the oil fields there are in general two types of boilers; those which are used for drilling wells and are of a more or less portable character, and those established later in a more permanent form and serve for the purpose,of generating steam for producing the oil. As a rule, the latter type of boilers are larger than those of the drilling type. Usually, little care is given to the installation of drilling boilers; particularly in attempting to set them up in such a way as to avoid waste in of fuel. Because of the temporary nature of these installations there may be some justification for not giving them more,attention in this resend, but it is believed that a few precautions could be taken that would amply repay the cost and trouble taken. In connection with the boiler plants that are afterwards established, when a few producing wells have been,brought in with a life of two to ten years and probably longer, much care to the boiler-plant construction and to the installation of recording instruments which will assist in operating the plant at minimum cost."

Nov 1, 1920

By L. M. Burman

The phase-boundary pressure required to maintain a natural hydrocarbon fluid in a single phase must be considered in planning the recovery of reservoir liquids by miscible-phase processes. The change in the phase-boundary pressure at reservoir temperature that results when a light component or a mixture of light components is added to a reservoir fluid is an especially important consideration. The cricondenbar pressure (maximum phase-boundary pressure) and the critical pressure are unique correlated pressures that have been utilized to calculate the change in phase-boundary pressure that may result when the composition of a reservoir liquid is altered by an additive. In this study one reservoir oil and three gas-condensate fluids are used as examples. Correlations pertaining to the critical and cricondenbar states in chapters 4 and 5 of Bureau of Mines Monograph 10 (3)5 were used to demonstrate how butane and lighter components added to these reservoir fluids affect their phase-boundary pressures.

Jan 1, 1962

By M. M. Gilkey

This report describes the effects of water shortage on Arizona's mineral industries. The information presented was obtained in interviews with company representatives. Operations covered included all State metal mines using substantial quantities of water and all concentrators and smelters. Also included in the survey were 8 operations in the nonmetallic group; 22 in the plating, metal-fabricating, and metal-forming categories; 1 public-utility power company; and 6 water companies. The extent of the water shortage in Arizona is reflected in mineral- industry water-use practices, in the high cost and low quality of water used at many operations, and in the stringency of State control of well drilling and pumping. Many mineral-industry operations are among those users most seriously affected by the uneven water supply.

Jan 1, 1963

By R. Pallini

The Franklin Research Center (FRO, a Division of The Franklin Institute was contracted by the U.S. Department of Energy to investigate the application of elastomeric materials for the purpose of smoothing loads on dragline thrust rollers. This report covers the design, fabrication, and demonstration of a portable- device for measuring roller circle track deviations and roller loadings. The results of this work are documented in this report. During December 1981, a field test group visited the Falkirk Mine, Underwood, North Dakota for the purpose of demonstrating the use of the designed and built device. The data collected indicates the practicality and usefulness of such a device for determining actual dragline roller circle roller loads, while the dragline is in service. The device was useful in determining roller load peaking that may be a contributing Factor in the premature failure of these thrust rollers. The device could be used for field evaluation of elastomeric cushioning materials used to eliminate these load peaks.

Jan 1, 1982