Search Documents

Bitumninous and semianthracite coal reserves underlie about 1,400 square miles of Arkansas, less than 2.7 percent of the state's total area. These deposits, located near the western border, contain an estimated 2.2 billion tons, of which about half are recoverable. This represents less than one-tenth of one percent of the national reserves. Most of the commercial coal is mined from thin beds that are at least 14 inches thick. In some locations, however, the coal beds can be as much as eight feet thick. Lignite was mined in southern Arkansas before the Civil War. Current estimates indicate that the reserves may be as high as 9 billion tons, which could be used in the state's coal-fired electric generating plants; however, these deposits are not being mined at present. Because many coal operations in Arkansas are small and the demand for coal is unsteady, the industry employs fewer than 25 miners on a daily basis. Arkansas gained primacy when its regulatory program was conditionally approved November 21,1980, subject to the correction of four minor program deficiencies. The regulatory program was fully approved January 22, 1982. Authority of the state to administer its Abandoned Mine Land Reclamation Program was granted upon approval of the Arkansas Reclamation Plan on May 2, 1983. Arkansas was the first state to assume responsibility for abandoned mine land emergency projects when its Reclamation Plan was approved.

Jan 1, 1992

By Robert J. Pokora

This report summarizes the work performed under USBM Contract No. J0100038, "Demonstration of Noise Control Techniques for the Crushing and Screening of Nonmetallic Minerals." The objectives of the program were to: a. Identify the prevalent sources of crushing and screening noise in portable and stationary plants b. Design retrofit noise control treatments for those sources c. Field test control treatments under actual operating conditions. A census of the nonmetallic industry was performed to determine the number and types of crushing and screening equipment. Based on the census, eight plants were selected and surveyed to assess the variety of noise sources, determine the worker noise exposure to those sources, and to identify possible constraints that had to be considered in designing and installing the retrofit controls. Three plants were selected from those surveyed and retrofit noise control treatments were designed, including: a. A primary crusher operator control booth b. Screen decks made of resilient cloth c. Screen feedbox impact pads d. Rubber feed plate for secondary crusher e. Rubber feed chute linings for secondary crusher f. Noise attenuating curtain for secondary crusher. A new primary crusher control booth was installed at one plant, and the operator noise levels were reduced from 97 dBA to 78 dBA. Screen noise at the two secondary crushing plants was reduced by 3 dBA to 7 dBA; crusher noise was reduced by 5 dBA at one of these two plants. Noise levels at normal outside operator and cleanup locations were reduced by 4 dBA to 7 dBA at one secondary plant, but operator/cleanup noise levels were not significantly reduced in the second plant due to rapid wear of installed materials. At one of the two secondary plants the retrofit noise control materials displayed excellent wear characteristics. The rapid wear of retrofit materials at the second plant was due to improper materials being supplied and changing circuit conditions.

Jan 1, 1982

By Michael C. Horn

The 61,470-acre Lick Creek Roadless Study Area is in the western Salmon River Mountains, centered 12 miles northeast from McCall, ID. U.S. Bureau of Mines personnel examined the roadless area in 1984. There is no recorded mineral production from the study area and no current mineral-related activity was observed. The roadless area is underlain by granitic rocks of the Idaho batholith. Pegmatite dikes and aplite dikes are present locally. Sampling indicates these rocks are not mineralized. No mineral resources were identified. INTRODUCTION This report describes the USBM (U.S. Bureau of Mines) portion of a cooperative study with the USGS (U.S. Geological Survey) to evaluate mineral resources and potential of federal lands recommended for wilderness, as required by The Wilderness Act of 1964. The USBM examines and evaluates individual mines, claims, prospects, and mineralized zones; USGS conducts broader geological, geochemical, and geophysical surveys. Such data helps Congress and other federal agencies make decisions affecting the use of public lands.

Jan 1, 1986

By James Gibbs

In order to provide an initial approach to the deposits of oil shale, nahcolite, and dawsonite in the central area of the Piceance Creek Basin in northwestern Colorado, the U.S.B.M. and associated contractor personnel drilled and cased a 96-inch ID shaft to a depth of 2,371 feet. The shaft was constructed using "big hole" drilling techniques and succeeded in giving access to previously inaccessible deposits of the above minerals. This report documents the construction from its beginning in January 1977 to its completion in January 1978. Procedures used and problems encountered are discussed in derail.

Jan 1, 1978

By Kenneth Eilerts

[Efficient and econonic production of ?etroleum requiros knowledge of the propertios of rescrvoir fluids a:$. their characterintics of flow throayh porous forclntions. The cllanga in propertie s and flow characteri s- tics of fluids when their corosition is altercd cs a rnsult of reservoir- pressure decliae is of 'mecial i~ortenct? ir, planning wall-spaAng pro.yama and production schedules. Rct~ntion of the ~eatent poscible quantity of dissolved gac in the rescrvoir liquid gnneml'y is recognized cs ess~ntisl to mxim ultimzte recoverj of oil fro3 the underground reecrvoir. Ilo:rever, pro6uction mothodn tending to mintain gis in solution in the oil and re- sulting in the optimm ocolo~ic recgvery of oil not only vary from field to fiold but also my have to be changed from time to time in a given field as it is being depleted of its recoveraklo oil. Const vestly there is need tc investigztc tY.e propertiec of resa:-voir f kids corresponding to successivc stages of reservoir depleJ&ion with the view of obtnining infomation oacential to efficient prcriuctian practices.]

Jan 1, 1939

By H. L. Riley

Cleaning and handling of fine coal are generally conceded to be more difficult problems than preparation of the coarser sizes. Increased mechanization in the coal-mining industry has, in general, resulted in an increased percentage of the fine sizes in the total coal mined. If the coal fines are cleaned by wet methods, the minus-1/16-inch square-mesh particles cause most of the sludge and slurry problems encountered in preparing wet coal. Equipment that separates coal from refuse on the basis of specific gravity is not efficient on sizes that, because of their fineness, do not follow the same laws of hindered settling as the larger particles. Probably the best solution of fine-coal cleaning problems is to use other methods, such as flotation, that utilize other physical characteristics than those determining hindered-settling ratios. Regarding the type of flotation known as the Elmore vacuum-flotation process there has been a scarcity of data and information available in this country. An investigation has therefore been made to obtain additional date and information on this process under laboratory conditions. During this investigation an effort has been made to evaluate the relative efficiencies of vacuum and mechanical laboratory froth flotation cells. The investigation included float-and-sink, screen-sizing, and flotation tests on 2 different samples of 14-mesh to 0 raw coal and an a sample of slurry from the settling-tank overflow of a typical washer. One raw-coal sample was obtained from the American bed and represented a type of coal that is relatively easy to clean. The other raw-coal sample was from the Mary lee bed and represented a type considered difficult to clean.

Jan 1, 1954

A new personal respirable dust monitor developed by Rupprecht & Patashnick Co., Inc. in a multi-year project funded by the National Institute for Occupational Safety and Health (NIOSH) generated promising results in underground coal mine testing performed by NIOSH and industry representatives during the summer of 2003. The mine data showed that the personal dust monitor (PDM) performed similarly to co-located manual reference samplers for full-shift samples at all four underground coal mines at which the evaluation took place. The technology that forms the heart of the PDM, called the tapered element oscillating microbalance (TEOM system), is unique in its ability to collect suspended particles on a filter while simultaneously determining the accumulated mass with National Institute of Standards and Technology traceability. Because the monitor measures the true particle mass collected on its filter, its results do not exhibit the same sensitivity to water spray as do optically based measurement approaches. The technique achieves microgram-level mass resolution even in the hostile mine environment, and reports dust loading data on a continuous basis. Using the device, miners and mine operators have the ability to view both the cumulative and projected end-of-shift mass concentration values, as well as a short-term 15- or 30-minute running average. During underground mine trials in the summer of 2003, technical personnel used the readings from the PDM to identify and correct several abnormal dust generating scenarios. These events demonstrated the potential of the PDM to be used as an engineering tool to evaluate the effectiveness of various dust control strategies. In a separate evaluation performed by CONSOL Energy, Inc., the mine operator evaluated the benefit of a proposed new water spray-based dust control system. Engineers measured the dust concentration upstream and downstream of a production location under different dust control scenarios using two PDM units. By evaluating the change in the dust loading between the upstream and downstream monitoring sites, the company was able to determine in a few hours which hardware configuration would yield the greatest benefit to the workplace environment. BACKGROUND Measuring underground coal mine dust concentrations is an essential part of protecting miners' health. The U.S. Secretary of Labor and the Federal Advisory Committee on the Elimination of Pneumoconiosis among Coal Mine Workers has recommended that better monitoring of coal miner dust exposures be used as a method to improve miner health. In consultation with labor, industry, and government, NIOSH issued a contract to Rupprecht & Patashnick Co., Inc. (R&P), Albany, N.Y., to develop a one-piece PDM. The object was to miniaturize TEOM technology into a form suitable for a person-wearable monitor that would enable accurate end-of-shift dust exposure information to be available to miners. Furthermore, any person-wearable dust monitor should minimize the burden to the wearer by incorporating the monitor into the mine worker's cap lamp battery, with exposure data continually displayed during the shift to enable workers and management to react to changes in dust exposure. In the summer of 2003, NIOSH conducted extensive testing of the PDM to determine its laboratory and in mine performance. In addition, anecdotal information collected in the mines showed several occasions where miners were able to identify situations that produced high levels of respirable coal mine dust The PDM's response to unplanned changes resulted in action being taken to keep dust exposures as low as possible. In another case that demonstrated the PDM's versatility, a mine was seeking to find a better dust control solution on its longwall headgate stageloader. In this instance, the PDM was used as a diagnostic tool by the miners to quickly evaluate the control technology. [ ] HOW DOES THE PDM WORK? The PDM is configured to provide accurate respirable dust personal exposure information in a form that is as convenient to wear as a normal cap lamp (See Figure 1). Respirable dust exposure data displayed by the device has two main objectives: providing the miner and mine operator with timely values to avoid overexposure to dust, allowing them to make any necessary changes during the course of a work shift; and computing an accurate end-of-shift statistic for a miner's average respirable dust exposure. The mass sensor embedded in the PDM, holds the key to the accurate, time-resolved dust concentration measurements. The inertial, gravimetric-equivalent, mass measurement technique used in the device typically provides a limit of detection on par with that of the most sensitive laboratory-based microbalances.

By Thomas J. Peters

The Goat Rocks RARE II further planning areas contain no known mineral resources and have very low mineral potentials. County mining records show only one mining claim area; however, no mineralized material was found at the described location. Andesite suitable for building stone may be present, but similar material can be quarried more economically elsewhere. Several anthracite coal prospects are near the area, but the likelihood of finding an economic deposit of coal or other fuel is very low.

Jan 1, 1981

By Vernon C. Davis

"INTRODUCTION This report describes the work done and presents the data obtained from limited diamond drilling at the lead-zinc deposits cf the Belle Eldridge Gold Mines, Inc., in Lawrence County, S. Dak. during the summer and fall of 1943. The work was undertaken in an effort to increase reserves and step-up production of zinc and lead so vitally important to the war program.The geology, topography and existing mine workings were mapped and studied. Subsequently, six vertical core-drill holes were put down from surface sites.ACKNOWLEDGMENTSIn its program of investigation of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of our natural resources to the end that they make the greatest possible contribution to national security and economy. The Mining Division, Lowell B. Moon, chief, conducts preliminary examinations, does the actual investigative work, and prepares the final report. The Metallurgical Division, Oliver C. Ralston, chief, analyzes samples and makes beneficiation tests, if such are necessary.Special acknowledgment is made to John Paul Gries, geologist, South Dakota School of Mines, for mapping and interpretation of geology and topography, logging of cores obtained, and his assistance in guiding the drilling."

Mar 1, 1948

By Frank D. Lamb

Four samples of manganese-bearing material from the Aroostook County, Maine, deposits were tested at the Eastern Experiment Station of the Bureau of Mines at College Park, Md., to determine their amenability to beneficiation by ore-dressing methods. The samples represented material from the Maple Mountain-Hovey Mountain deposit, the Dudley farm, and the Burnham farm and contained 11 to 14 percent manganese. None of the tests produced appreciably enriched concentrates suitable for further treatment for the production of ferromanganese. The intimate association of the manganese minerals with iron and siliceous minerals requires extremely fine grinding to liberate the manganese minerals in these ores and prevents efficient concentration by physical means.

Jan 1, 1953

By David C. Benson

This Bureau of Mines report is an update of IC 8725 and comprises tables listing the name, location, and other pertinent data concerning certain fuel-related projects. The tables include information on projects involving the proposed or planned development of fuel resources, as well as the development of storage, transportation, and conversion facilities; the report covers the 26 States east of the Mississippi River. Of the total 535 projects for which information is provided, 429 concern coal mines and electric generating plants (including Energy Supply and Environmental Coordination Act (ESECA) coal conversion notices).

Jan 1, 1978

By M. M. Ayoub

This volume is the second of three volumes comprising the final report of the research project "Biomechanics of Low Coal." It covers only the anthropometric study of low coal miners. Volume I summarizes the overall biomechanical, anthropometry, and work physiology study conducted. Development of work clothes modified to meet the needs of low coal miners is described in Volume III. The male and female anthropometry, with the exception of weight and circumferential dimensions, was quite similar to the comparison populations. The miners tended to be heavier and have greater circumferences. The measurements made in this study were used to develop 5th, 50th and 95th percentile, quarter and half scale, male and female mannequins. These twelve mannequins can be used in work place and equipment design and redesign.

Jan 1, 1982

By D. Bienstock

The use of alkalized alumina in removing sulfur dioxide from a coal-combustion flue gas at 625° F was investigated on a pilot plant scale. The absorber was 26 feet long and 1.6 inches ED. Counter-current gas-solids flow at gas velocities of 8 to 15 ft/sec in the presence and absence of baffles, as well as solids entrainment at gas velocities of 20 to 23 ft/sec with solids recycle, were employed. The spent absorbent as regenerated as fixed bed with the reducing gases--reformed natural .7.7d hydrogen. Of absorption-regeneration were successful completed using the alkalized alumina rolled into spherical granules 10 to 16 mesh. There was no loss in activity of absorbent toward SO2 with a modest attrition equivalent to 0.l percent of the solids feed. Supporting studies were conducted on the effect of the sodium content in the absorbent, the composition of the reducing gas, thermal treatment to increase absorbent hardness, and removal of absorbed chlorine from the absorbent. A mathematical model was formulated to describe the removal of SO2 by alkalized aluminum from fixed and falling beds.

Jan 1, 1967

By Phillip R. Moyle

A cobalt/manganese occurrence in Clark County, Nevada was the subject of a site-specific mineral investigation by the U.S. Bureau of Mines in 1988-90. The study site is in the northern part of the Million Hills (wilderness) study area which is administered by the Bureau of Land Management. Field work during a period of one week consisted of geological mapping and sampling of workings and outcrops, and geochemical and geophysical surveys conducted on four transects totalling 7,600 ft. Although the concentrations of cobalt (0.1 to 0.5 percent) detected in samples from the fissure zones are within the range of grades associated with world-class economic deposits, the volume of material enriched in cobalt at the study site is insufficient to warrant consideration as a potential resource. Concentrations of manganese, nickel, copper, lead, zinc, barium, and thallium, although anomalous, are too low for economic consideration. At the study site, workings consist of three trenches and nine pits. The exploration history is unknown, and no production is reported.

Jan 1, 1990

By L. Garner McDonald

The U.S. Bureau of Mines, under contract to the U.S. Department of Energy, investigated the erosive-wear properties of seven commercial alloys with potential applications as valves for coal-conversion plants. A dry particle, jet-erosion apparatus was used to determine the wear of seven materials: 316 and 440-C stainless steels, K-68, K-701, and K-801 cemented tungsten carbides, HC-250 white cast iron, and Haynes 6B. The alumina abrasive entrained in the nitrogen gas jet had particle sizes of 27 or 50 µm, the abrasive velocities were 55 to 170 m/s, and the particle impingement angles were 15° to 90°. The maximum specific wear for ductile materials was found to occur at impingement angles of 15° to 30°, and the minimum specific wear occurred at 60° to 90°. For the brittle materials, maximum specific wear occurred at impingement angles of 50° to 85° and minimum specific wear was at the lowest angles. As the velocity and erosive particle size increased, the specific wear increased. The specific wear was related to the velocity by the power function WocAVn, where n was 1.8 to 3.9 for ductile materials and 1.8 to 3.6 for brittle materials.

Jan 1, 2010

By Raymond B. Ladoo

Garnets are usually found well crystallized in the cubic system , the principal forms being rhombic dodecahedrons , tetragonal trisoctahedrons or combinations of the two , and hexoctahedrons . They also occur as rounded disseminated glassy grains and in compact massive , laminated or gramlar aggregates . They vary greatly in color , but the most common garnets , almandite and andradite , are most often found of a dark red or reddish brown color .

Apr 1, 1922

By Kenneth H. Johnston

Records show that waterflooding was tried in Osage County as early as 1934, but it was not economically important until a large unitized flood in the North Burbank field was begun in 1950. Development was rapid and by the end of 1960, there were 70 active water flood projects and 16 active pressure-maintenance projects in the County. The locations and status of the water-flood and pressure-maintenance projects in Osage County on December 31, 1960 are shown in figure 1, and information pertaining to these projects as of July 1, 1960 is given in table 1. For the past several years, Bureau of Mines petroleum engineers have arranged tours of selected waterflooding projects for the spring meeting of the Kansas-Oklahoma Water flood Association. These tours are conducted to demonstrate unique operating methods and new field equipment and to provide additional opportunities for exchanging information. Each of these tours has been supplemented by a published report describing in detail the projects visited. This report has been prepared for distribution during the 1961 spring tour of three waterflooding projects and a pressure-maintenance project in Osage County, Okla. (fig. 2).

Jan 1, 1961

In 2006, a total of 4,573 stone mining operations reported employment to the Mine Safety and Health Administration (MSHA).1 Stone mines comprised 30.7% of all mining operations. ? Mines producing the primary commodity of limestone (crushed and broken) comprised the largest number of operations (n=2,042; 44.7%). ? Stone mining operations were located in all states and territories except Delaware and North Dakota. ? Pennsylvania had the most stone mines (n=368; 8.0%), followed by Texas (n=342; 7.5%).

Jan 1, 2008

By Paul C. Hyndman

Three properties in the Tuolumne River RARE II area, the Eagle Bluff Mine (lode) and the Indian Creek Bar and Bossy Bar Prospects (placer), have identified subeconomic gold resources (table 1). Nineteen other properties have potential for gold resources. Adjacent to the study area, five properties have identified mineral resources, and nine others have potential for resources. Properties having high-grade zones (shoots), but licking enough tonnage to be classified as resources, are listed in table 2. Gold, in lode and placer deposits, is the principal mineral commodity in the Toluene River study area. Ten properties within the RARE II boundary have gold-rich zones or shoots; they range in size from 12 to 2,500 tons and in average grade from 0.09 to 0.97 oz gold per ton.

Jan 1, 1983

By Denis Dwyer

[This paper describing mining, treatment methods, and costs at Plant No. 1 of the Western Indiana, Gravel Co. at Lafayette, Ind., is one of a series on gravel and sand mining being prepared for and published by the U. S. Bureau of Mines. These papers are designed to disseminate technical information regarding the methods used. The cost tabulations represent operating expenditures only and not total costs. It is recognized that publication of total costs might in many instances cause embarrassment to individual producers, as well as to industry as a whole. On the other hand, operating costs are essential to e technical discussion and study of the methods employed, The attention of the reader is specifically called to this differentiation in order that no Misunderstanding of the scope of the cost tabulations shall ensue.]

Jan 1, 1933