Search Documents

By M. P. Board, J. K. Whyatt, T. J. Williams

The U.S. Bureau of Mines has been conducting a series of rock mechanics investigations at the Lucky Friday Mime in the Coeur d'Alene Mining District of northern Idaho. In the present study, the energy release rate (ERR) index was used to evaluate three underhand stope backfill parameters--cement content, density, and placement gap-to determine their influence on rock bursts. This index provides a relative measure of the likelihood of rock bursting for a given rock mass. It is known that the elastic idealization of the rock mass inherent in this method causes underestimation of stope closure and hence underestimation of the influence of backfill on rock bursting. However, this evaluation still showed that (1) changing from present practice to one in which backfill was omitted altogether would increase the ERR by 42 pct and (2) perfect placement of backfill would reduce the ERR below present practice levels by 28 pct. The easiest step toward perfect placement would be elimination of the placement gap, which accounted for half of the difference in ERR between present practice and ideal placement conditions. There was no indication that increasing initial fill strength through increased cement content would affect the ERR.

Jan 1, 1992

By Richard C. Moore

The U.S. Bureau of Mines contracted a study to estimate what effects the underground mining of thick coal seams in the western United Slates would have on the surrounding water resources. Potential coal fields in the western United States where this type of mining might occur were identified. The foreign literature was searched for studies of effects on hydrology from thick seam underground coal mining. Based on the limited information obtained from the foreign literature, estimates of the effects of this type of mining on the ground and surface water in the western states were made.

Jan 1, 1980

Now more than ever, the United States must have an adequate and dependable supply of minerals to meet its defense and economic needs. A chief mission of the U.S. Department of the Interior Bureau of Mines is to help ensure that the United States meets these needs at acceptable environmental, energy, and economic costs. As it looks toward the 21st century, the Bureau of Mines will focus its attention on the following areas: - upgrading the capabilities of its mineral information and analysis program - expanding mineral land assessment activities - disseminating the practical results of federally funded research activities to the private sector through enhanced technology transfer - addressing the impact of regulations on mineral industries - addressing the needs for mineral-oriented training and research in the Nation's universities - enhancing mine worker health and safety - improving mining and mineral processing productivity through automation, robotics and other innovative technologies - reducing the environmental impact of mining and mineral processing operations - and enhancing the accessibility and conservation of domestic mineral resources.

Jan 1, 1991

By Byron S. Gottfried

This Bureau of Mines report presents a method for combining the distribution curves at different specific gravities of separation, for a given piece of coal-cleaning equipment and a given raw coal feed, into a single, generalized distribution curve normalized with respect to specific gravity and, therefore, independent of the specific gravity of separation. Illustrative generalized distribution curves, based upon Bureau of Mines collected data on industrial operations, are presented for five different types of coal-cleaning equipment. The well-known concept of probable error is extended to the generalized distribution curve. It is shown that the conventional probable error is directly proportional to the specific gravity of separation. A number of sample calculations, illustrating the use of the generalized distribution curve and generalized probable error, are presented in the appendix.

Jan 1, 1977

By D. B. Dow

The presence of sulphur compounds in petroleum and its products is, generally speaking, undesirable, and the problems involved in removing such compounds are of great importance to the petroleum refiner and to the manufacturer of gasoline. There are several types of these compounds which are dissimilar in physical and chemical characteristics, as evidenced by different objectionable features which they exhibit, and special treatments have been developed to meet conditions existing in various products. This paper deals with the treatment of natural-gas gasoline for the removal of certain sulphur compounds which, if not removed, impart on objectionable odor and in addition badly discolor the product. The presence of this particular type of sulphur compounds is detected by the "doctor" test.* In some instances natural-gas gasoline is purchased on "doctor" test specifications, and the ordinary purchaser, while not buying on "doctor" specifications, is insistent in his demand for a water white product. Gasoline which fails to meet the "doctor" test, if not received by the buyer within a few weeks after time Of manufacture, may be "off color" enough to warrant a deduction from the market price.

Jan 1, 1923

By R. S. Olsen

The Bureau of Mines is engaged in research to recover aluminum from kaolinitic clay and other nonbauxitic domestic resources. As part of this work, calcined Georgia kaolin was prepared by a process that prevents slime formation and makes the leached residues fast settling and easy to filter. The leaching reaction for calcined kaolinitic clay in a 5 pct stoichiometric excess of boiling 23-to 26-pct HCI was found to be zero order. Rate constants based on the weight-fraction of aluminum in the clay were found to be between 0.095 and 0.15 min-1 depending on feed preparation and leaching parameters. The mathematical relationships between aluminum extraction and time for both batch and continuous, stirred-tank operations were derived and verified experimentally.

Jan 1, 1983

By R. W. Stahl

Coal mining has been revolutionized by the continuous miner. This machine has replaced, or has combined into 1, 3 former operations: Cutting, blasting, and loading. During the 25-year period before this machine was introduced, advances had been made in transportation, but the actual "coal getting" remained virtually the same. As frequently occurs, the multiple-purpose continuous miner introduced a new hazard--more rapid liberation of methane. The coal output formerly obtained from 10 to 20 working places might now be obtained from 1. It is true that circulation of air was generally increased; but the bulk of this machine virtually precludes continuous flow of air across the face, where gas may accumulate. Apprehension about this possible hazard led the Bureau of Mines to test face atmospheres during operation; and Report of Investigations 5288, Methane Buildup During Cutting and Continuous Mining Operations (published in 1956), presents proof that real danger may be present in many otherwise well ventilated mines.

Jan 1, 1958

By Spangler Ricker, F. T. Johnson

"SUMMARYThe Ione-Carbondale clays area is 2 miles northwesterly of Ione, Amador County, Calif. It was explored during the war by the Bureau of Mines to obtain data on the alumina content and to recover representative samples for beneficiation tests for alumina recovery.Seventy holes, aggregating 8,837 feet, were drilled, and about 10.3 acres of land was cleared of underbrush. Maps and cross sections were compiled showing location of holes, analyses, and other pertinent data.The clay beds vary in thickness from 13 to 196 feet, and are covered by a loose overburden, averaging about 11.9 feet in thickness. The ratio of overburden to clay is 1 : 8.2. Analysis of a composite sample showed the recoverable alumina (A12O3) and Fe2O3 content to be in the order of 23.6 percent and 2.8 percent, respectively.Topography of the clay area is ideal for open-pit mining methods and plant site.INTRODUCTIONInvestigation of alumina-rich clays for the possible production of aluminum was made during the recent war period, when the shortage of bauxite was becoming critical.Results of field examinations by the Bureau of Mines and the Federal Geological Survey indicated that one of the most promising areas for the development of alumina-rich clays is in the Ione-Carbondale district."

Mar 1, 1948

The production and processing of crude petroleum and natural gas are the dominant economic sectors of the Middle East, providing more than 80 % of the region's foreign exchange. In 1992, the 15 countries that constituted the region accounted for 29.5 % of world crude petroleum output, 20 % of world natural gas plant liquid production, and 5 % of world dry natural gas production. Only Cyprus and Lebanon were not crude petroleum producers. A fairly wide range of non fuel minerals is also produced in the region. The most significant are boron minerals, bromine, chromite, gypsum, phosphate rock, potash, strontium, and sulfur. However, the variety of minerals produced, output levels, and the size of the overall non fuel mineral economy of the region is dominated by Iran and Turkey. Turkey, with a diverse mineral production and strategically situated between Europe and the Middle East, was first in world production of run-of-mine boron minerals, second in strontium behind Mexico, and fourth in pumice. It was also a significant world producer of chromite, magnesi'lm compounds, mercury, and sodium sulfate. Turkey was also the Middle East's largest cement and steel producer. Iran continued to expand output of most mineral commodities following the war with Iraq from 1980 to 1988. It was a significant world producer of gypsum and strontium and on its way to becoming a major iron and steel producer in the region. Despite a very small domestic mineral industry, Israel was second in world production of bromine and a significant producer of phosphate rock and potash. In terms of processed minerals, Israel was a major world diamond cutting center and exporter of cut diamond. Jordan ranked sixth in world production of phosphate rock. Saudi Arabia was eighth in world production of sulfur.

Jan 1, 1994

By Charles L. Kimbell

The year 1980 on the whole was not a good year for the world's mineral industry. The general upturn of activities in 1979 after a rather poor 1978 showing was not maintained with a number of key measurement standards showing downturns. Most notably, the world's steel and petroleum industries recorded significant reductions in output, the former in response to markedly lower demand levels and the latter partly in response to lower industrial consumption owing to general economic conditions and partly owing to successes in campaigns for the reduction of energy use in general and petroleum product use in particular among major importing nations that were feeling the trade balance pinch of ever-higher oil prices. During 1980, a number of political events-some international in scope, some confined to single nations-had significant influence upon world mineral industry activities and mineral commodity supplies, and other political happenings had the potential to significantly affect the industry in future times.

Jan 1, 1982

By E. C. Strycula

Solid-state equipment offers a number of potential advantages in the coal mining industry. These advantages can only be realized, however, through careful and judicious design of the control and protection circuitry. Problems relating to the interaction of solid-state equipment on the electrical system and the special design considerations which apply to solid-state circuitry are examined. Design guidelines are provided for solid-state applications in the areas of: (a) equipment operated from a DC trolley wire, (b) drive systems for surface mining equipment, (c) AC motor starters, and (d) electromagnetic interference.

Jan 1, 1981

By Gerald R. Smith

Because of continuing concerns regarding the effects of cumulative quantities of materials in the environment, the Bureau of Mines has initiated a series of studies to evaluate, to the fullest extent possible, all aspects of the materials flow sequence fur selected commodities. Although tungsten and its compounds do not pose a significant health hazard to the environment, they do represent valuable resource materials to which appropriate conservation considerations must be given. The present study includes a description of recent trends in the consumption, loss, and recycling of tungsten-containing materials in the United States during the period 1974 to 1991 and an estimation of the cumulative loss of tungsten to the environment since 1910. Obsolete tungsten is recycled primarily as cemented tungsten carbide components that have been used in cutting and wear-resistant applications. The quantity recycled, as a of annual U.S. consumption of tungsten, was estimated to have increased from 10% in 1974 to 341a in 1991. An estimated 58% of the 148,000 metric tons of primary tungsten consumed since 1910 was lost to the environment through means such as dissipation, discard, and dilution.

Jan 1, 1994

By Alvin M. Cummings

During the period from June to September 1943, the Bureau of Mines undertook an investigation of the Vial mine, near the village of Linden I in Iowa County, Wis., as part of a general investigation of the zinc-producing area of southwestern Wisconsin. The work was done when every effort was being made to increase the production of metals important to the Nation's war program. The Bureau completed 29 churn-drill holes aggregating 3,348 feet of bore in areas immediately north and west of the old Vial mine, which had been worked intermittently between 1908 and 1939. The drilling supplemented a previous drilling program by the lessees and disclosed the presence of two significant zones of mineralization.

Jan 1, 1948

By Albert L. Toenges

The introduction of mechanized mining in coal mines, which has speeded loading, has emphasized the importance of efficient underground transportation systems. The purpose of this investigation is to study and analyze various systems now in use, and to derive conclusions therefrom. This report may be helpful to operators who are planning new systems of transportation or who are revising present systems to increase their efficiency. This paper is the first of a series on this subject and des¬cribes some systems of transportation `utilizing rail haulage, ACKNOWLEDGMENT The information used in preparing this report was obtained through the courtesy and cooperation of the officials of the companies whose mines were studied. The descriptions of the transportation systems at the mines included herein have been checked for accuracy, and publication of the data has been approved by the executives of the several operating companies.

Jan 1, 1940

By Michael A. Trevits

The National Institute for Occupational Safety and Health (NIOSH) in partnership with Strata Products tested the sealing capability of Ventstop®? as part of an ongoing mine fire control and suppression research program. Ventstop®? is a multi-purpose, inflatable device that is produced by Minvent Solutions and is available world wide for use in the metal and nonmetal mining industry. Ventstop®? is also used in the Australian coal industry as a temporary ventilation control device. The device can be quickly deployed, is reusable and can be placed in horizontal and vertical mine voids to control dust, fumes and smoke. Deployment, multi-day inflation and air leakage tests were conducted at the NIOSH Lake Lynn Laboratory to determine the capability and limitations of Ventstop®? in a simulated coal mine setting. During the tests, Ventstop®? was also subjected to low level forces of a nearby methane gas ignition. It is thought that Ventstop®? could be used by the US coal mining industry to temporarily close an underground mine area in response to a fire or spontaneous combustion heating event, to temporarily redirect mine ventilation during longwall equipment moves or during stopping construction. This paper describes this inflatable temporary mine sealing technology and presents the results of the NIOSH tests. Disclaimer: The findings and conclusions in this report are those of the authors and do not necessarily represent the views of NIOSH.

Jan 1, 2009

By B. K. Shibler

During the investigation of the occurrence of manganese deposits in the Western United States, examining engineers of the Bureau of Mines collected 2-ton samples from five manganese properties near Golconda, Nev. Extensive laboratory tests were made to determine the amenability of these ores to standard ore-dressing methods of concentration. The Tom Major property, one of those sampled, is situated 12-1/2 miles south of Golconda, Humboldt County, Nev. The deposit is described as a bed about 5 feet thick in a thinly bedded shale and dolomite formation. The sample tested was obtained from the manganese bed, but the examining engineer reported: "The mining of an appreciable tonnage at reasonable cost would perhaps cut in half the grade represented by the sample."

Jan 1, 1951

By Floyd G. Anderson

Owing to the rapid growth of the perlite industry in recent years, the Bureau of Mines has received numerous requests for information relative to the possible harmful effects of breathing dust resulting from the processing and use of perlite. As published information on the composition of perlite is rather meager, consisting chiefly of conventional chemical analyses, samples of crude and expanded perlite from 9 deposits in 6 Western States were studied. Crude perlite ores were examined petrographically and analyzed by chemical, spectrographic, and X-ray-diffraction methods. Sized crude and expanded perlites were analyzed chemically for total free and combined silica content.

Jan 1, 1956

By John Taber, JOHN B. HOPKINS

During World War II , a critical shortage of domestic abrasive corundum developed . Late in 1944 , the shortage became so acute that it was deemed advisable to investigate certain low-grade corundum prospects in Madison and Gallatin Counties , Montana . The Gallatin , the Bozeman , and the Bear Trap deposits were the principal ones investigated . The Bear Trap deposit was examined by E. W. Newman and Robert S. O'Brien , engineers of the Bureau of Mines , in August 1944. Exploration was started in October 1944. Field work was completed late in the spring of 1945 . report presents the data obtained from the exploration .

Mar 1, 1947

By Ronald P. Hollenbeck

This study reviews and discusses the fluorspar industry in the Eastern United States, with emphasis on factors controlling the industry such as production, consumption, uses, and transportation. The greatest potential for increased consumption of fluorspar in the immediate future was found to be in the manufacture of fluorine chemicals and steel. Important factors affecting the future domestic industry include imports and the maintenance of adequate domestic fluorspar reserves. Exploration, commercial deposits, mining and milling, reserves, and new developments in the industry are covered.

Jan 1, 1967

By J. H. Johnson

The report references reports and publications from 1975 to the present related to diesel underground mine air quality research undertaken by Michigan Technological University. Research results obtained on this contract are summarized in 5 different sections as follows: Section 1 - Development of a Systematic Approach to Monitoring, Data Analysis, and Interpretation for Diesel Mine Air Quality Control, Section 2 - Experimental Evaluation of LHD On-Board Air Quality Control Systems, Section 3 - Development of a Portable Self-Contained LHD Tailpipe Emissions Measurement Apparatus for NO , N0, CO, CO , and Particulate Matter, Section 4 Quantitative Analysis of Diesel and Coal particulate Matter by Laser Raman Spectro¬scopy and Section 5 - Development and Application to Detector Tubes of a Laboratory Method to Assess Accuracy of Occupational Diesel Pollutant Concentration Measurements.

Jan 1, 1985