Search Documents

By W. S. Wright, A. W. Tolonen

"INTRODUCTION The Mount Andrew iron deposit on Kasaan Peninsula, Prince of Wales Island, Southeastern Alaska, was examined in August 1942 by an engineer 4/ of the Bureau of Mines accompanied by geologists 5/ of the Federal Geological Survey. From October 20 to 27, 1942, two engineers 6/ of the Bureau of Mines made a further preliminary examination and took three large samples of magnetite and magnetite-copper ore for metallurgical testing. During the stunner of 1942 an investigation of the Mount Andrew-Stevenson-Mamie area, including topographic and geologic mapping and a magnetic survey, was made by geologist 7/ the Federal Geologically Survey. On May 31 and June 2, 1943, two Bureau of Mines engineers 8/ conducted a preliminary examination in which special attention was directed to trails, camp, and drill sites. They were accompanied on May 31 by L. A. Warner of the Geological Survey.During the period from September 1943 through September 1944 Bureau of Mines engineers 9/ completed a thorough investigation which included trenching, core drilling, and sampling. A Federal Geological Survey representative 10/ examined all trenches and cores for geological data.LOCATION AND ACCESSIBILITYThe deposit is situated at latitude 55º 31' N. and longitude 132º 18' W. on the north side of Kasaan Bay on Prince of Wales Island, Southeastern Alaska. The general location is shown on figures 1 and 2. The deposit is 5 miles southwest of the village of Kasaan and by water, 27 miles northwest of Ketchikan; the main tunnel portal is 7/8 mile north of the Mount Andrew landing on Kassan Bay."

Nov 1, 1947

By M. G. Zabetakis

Benzene and toluene are the first two members of an important homologous series whose general formula is CnH2n-6. The members of this series differ in composition from benzene by some integral multiple of CH2; they can all be prepared in the laboratory by the Wurtz-Fittig, Friedel-Crafts and Grignard syntheses. Because 'of the industrial importance of these-hydrocarbons, the limits of flammability of eight members of the series have been determined at 100° C.-(A temperature of 1000 C. was chosen because the determination of the upper limit of flammability of p-cymene requires an apparatus temperature. of at least 90° C. As elevated temperature data are available for other combustibles at 100° C. but not at 90° C., all data were taken at 100° C. in order to obtain comparable results.) Minimum ignition temperatures of these combustibles have been determined at laboratory-pressures.

Jan 1, 1951

By M. M. Fine

The results of tests on oxidized lead ores from two properties are reported in this paper. The investigation was on a small laboratory scale only; no pilot-plant tests were made. One sample, from the Magajupa Mining Co., near Duenweg, No., contained coarsely crystalline and disseminated galena and cerussite, so both tabling and flotation were considered in the beneficiation. By this treatment of an ore containing 11.5 percent lead, a recovery of 79.5 percent of the lead was made in a concentrate containing 73.3 percent lead.

Jan 1, 1948

By M. Kanda, W. D. Bensema, J. W. Adams

Two different techniques were used to make measurements of the absolute value of electromagnetic noise in and above an operating coal mine, McElroy Mine, located near Moundsville, Nest Virginia. The electromagnetic environment created by 300 volt dc and 480 volt ac machinery was measured. In one technique noise was measured over the entire electromagnetic spectrum of interest for brief time periods. The noise was recorded using broadband analog magnetic tape. The noise data was later transformed to give spectral plots. In the other technique, noise amplitudes were recorded at several discrete frequencies for a sufficient length of time to provide amplitude probability distributions. The specific, measured results are given in a number of spectral plots and amplitude probability distribution plots.

Jan 6, 1974

By Kenneth H. Johnston

This report describes an in situ combustion project and three waterflood projects in Allen, Anderson, and Wilson Counties, Kansas, that will be visited during the 1964 annual tour of the Kansas-Oklahoma Waterflood Association. Among the unique features of the projects are the movement of heavy crude oil through the reservoir and into the wellbore with energy furnished by burning s portion of the crude oil therein. Another feature is the simultaneous injection of C02 and water, through separate tubing into input wells during early development, to increase injectivity at moderate pressures, Discussion of individual projects includes information on their early history, source and treatment of injection fluids, oil production-decline curves, and the results of water injection on oil production.

Jan 1, 1964

The Pittsburgh (Pa.) and Spokane (Wash.) Research Laboratories are among the world?s foremost mining research establishments. Once a part of the former U.S. Bureau of Mines (USBM), which was abolished by the U.S. Congress in fiscal year 96, health and safety research at these laboratories was transferred to the National Institute for Occupational Safety and Health (NIOSH). NIOSH is the Federal agency responsible for conducting research and making recommendations for the prevention of work-related illness and injury. The Institute is part of the Centers for Disease Control and Prevention within the U.S. Department of Health and Human Services. Over the past two decades, the Pittsburgh and Spokane Research Laboratories have produced sustained technological achievements in mining health and safety, including? ? Development of novel respirable coal dust control technologies and more effective monitoring techniques to reduce worker exposure to hazardous mine dusts. ? Improved ground control technologies to warn and protect miners from the dangers of coal mine roof collapses and other hazardous strata conditions. ? Improved ergonomic design criteria and training methods to protect mine workers from injuries and fatalities associated with equipment and manual tasks. ? Development of enabling technologies that allow miners to control their mining equipment from a physically safe, protected work area away from respirable dust, harmful noise levels, and roof collapses. ? Improved mine fire detection and extinguishment techniques. ? Development of smaller, lighter, and safer emergency breathing devices.

Jan 1, 2007

By Cleo G. Rall

The value of brine analyses in the study of petroleum-engineering problems was recognized early in the history of petroleum. The Bureau of Mines before 1928 had indicated in several reports.3/ ways in which analyses might be used. Because of the confusion resulting from attempts to correlate the work of different chemists using greatly varying methods of analysis and systems of computation and expression of results, a paper presenting the methods used by the Bureau of Mines was prepared and published in 1928. This system of determining the characteristic constituents of oil-field waters and of calculating and reporting results has been widely adopted by the petroleum industry. The earliest and most obvious use of water analyses is determination of the source of water infiltrating into petroleum and natural-gas wells. For this purpose it is necessary that an analysis of the connate water of the formation from which the oil is produced be available and that an analysis of the contaminated water be made. By comparing these analyses with those of connate waters from formations higher in the structure, the formation from which the infiltrating water comes may be identified.

Jan 1, 1953

By D. S. Burgess

A commercially available Halon 1301 extinguisher has been evaluated as part of an explosion-suppression system for use in coal mines. Studies were made both of the dispersion pattern of the Halon 1301 at an initial pressure of 280 psig, and of the efficacy of this suppressant against 9.5 percent methane-air flames. These flames were quenched successfully only when the suppressant was applied before the fireball diameter exceeded 18 inches.

Jan 1, 1971

By N. O. Johnson

This is one of a series of-Information Circulars dealing with mining and milling methods and costs at mines in various districts in the United States. The Hog Mountain gold mining district is of the northern edge of Tallapoosa County, in the east central part of the State of Alabama. The district is equally close to Goodwater and to Alexander City, both stations on the main line of the Central of Georgia Railroad. From Alexander City the mine is reached by 13 miles of graded road, traveling in a northeast direction. In dry seasons the road is good; in wet weather it is bad but passable. Improvements are being made constantly on the road, so that in the near future the gravel road should be good under all weathered conditions.

Jan 1, 1936

By W. H. Young

MOST OF THE key items in the bituminous-coal and Lignite industry declined in 1954 compared with 1953. Production, consumption, exports, average value per ton, men working, and days worked all declined; however, in the field of mechanization, the percentages mechanically loaded, mechanically cleaned, mined by auger, and mined by stripping all increased, as did production per men per day. Production.-The output of soft coal in 1954-391.7 million tons- was 14 percent less than the 457.3 million tons produced in 1953. The lower production in 1954 was due largely to a sharp reduction in consumption in the United States and to a drop in exports.

Jan 1, 1958

By T. D. Moore

Methane emission from two surface gob-degasification boreholes was measured by the Bureau of Mines. The investigation took place during mining of a 3,200-foot longwall panel in the Lower Kittanning coalbed in central Pennsylvania. The first hole was 500 feet from the start of mining, and the second hole was 2,200 feet. The first hole went on natural draft as soon as the longwall face passed it. This caused the methane flow in the return entries to drop 75 pct. In the 6 months required to complete the panel, the two holes emitted 69 MMcf of methane in varying percentages of concentration in air. In 3 years, the holes emitted a total of 150 MMcf of methane.

Jan 1, 1976

By W. W. Adams

The metal and nonmetallic mineral mines (excluding coal mines) of the United States had a more favorable safety record in 1935 than in any year except 1931 and 1932 since annual statistics of accidents first became available in 1911. The accident rate was even lower than that for 1911, when the recorded rate probably did not reflect all of the accidents that actually occurred because many companies had not yet begun to keep complete records of accidents, especially those causing only minor injuries, and when, therefore, the number of accidents revealed by the companies' reports to the Bureau of Mines was probably not as complete as that reported for later years. Compared. with 1911, the accident rate covering fatal and nonfatal injuries in. 1935 decreased 13 percent. Compared with 1925, when the rate was the highest ever reported, the rate for 1935 decreased 47 percent and compared with 1934, 7 percent. The progress in safety which the mines of the country made in 1935 was not confined to any section or mining region; it was shared by a majority of the mining States and applied to underground mining operations, to open-pit mining, and to work at surface shops and yards. The rate for underground mining declined 8 percent from 1934; the rate for open-pit mining declined 14 percent, and that for surface shops and yards 12 percent.

Jan 1, 1938

By Ernest W. Loya

The Bureau of Mines has developed a computer program for calculating the composition of gravimetric primary standard gas mixtures. The Fortran IV program applies corrections due to buoyancy variations of the cylinder and inaccuracies of the balance weights. The program also determines the statistical error due to the sensitivity and precision of the balance and applies the analytical error of the weighed gases.

Jan 1, 1985

By Sumner M. Anderson

THE importance of the mineral industries of the Latin American area in 1964 may be evaluated in respect to a number of points of reference, a few of which are measurable and appropriate for examination. With regard to the region's contribution to total world production, it accounted for total 1964 world output of natural nitrates (from Chile), and about 97 percent of the optical and electrical grades of quartz crystal (from Brazil). The region supplied over 20 percent of world output of 7 other mineral commodities and accounted for 4 percent or more of world output of 19 other mineral products. Among major commodities, the area, occupying 15 percent of the earth's land surface, supplied within 3 percent of that proportion of the world's output of copper, lead, tin, zinc, barite, and crude petroleum. Incomplete compilation of production data, particularly that of nonmetallic minerals, precludes production estimates on some items for the area ass whole, and therefore the importance of Latin America as a world producer of some additional commodities may not be clearly assessed. For example, most of the countries of the area collect only incomplete data or no data at all on the production of clays and other ceramic materials, sand and gravel, dimension and crushed stone, lime, ornamental and precious stones, perlite, vermiculite, carbon black, coal tar products, and petrochemicals. In the case of many countries of the area, the value of production of one or more of these commodities greatly exceeded that of other mineral industry products that are carefully reported.

Jan 1, 1966

By J. Drew Potts

In this U.S. Bureau of Mines study, four underground respirable dust surveys were conducted to determine factors affecting belt entry dust levels and how using belt air to ventilate work areas affected dust exposures. Belt entry dust levels on the surveyed longwall and continuous miner sections averaged 0.59 and 0.26 mg/m3, respectively. The stageloader-crusher contributed an additional 0.5 to 0.9 mg/m3 of dust to belt air, while the feeder-breaker contributed 0 to 0.2 mg/m3 of dust. A 1,000-ft increase in belt entry length or a 200-to 500-st-per-shift increase in production resulted in roughly a 0.1-mg/m3 increase in dust. Using the belt entry as an intake entry on the continuous miner section appeared to reduce dust levels by 0.1 to 0.3 mg/m3 during cutting. Belt air was not used to ventilate the face on the longwall section.

Jan 1, 2010

By Mark Sanders

The report describes three experiments that were conducted to determine the effects of size and weight of the miner's battery pack on performance in the low seam coal environment. Three separate experiments were carried out in a simulated low seam coal mine. The first experiment tested the sensitivity of task measures (i.e., subjects performed locomotion) shoveling, cart pushing, and timbering tasks) to detect variations in the size and weight of the battery pack. The results of the first experiment demonstrated that only the locomotion tasks were sensitive to size and weight variations. The second experiment, therefore, focused on the locomotion tasks and tested the effects of varying size and weight on task completion time. The third experiment was designed to compare the present battery pack to a radically different configuration of power cells. The most important findings were that changes in weight affected locomotion times but changes in size and configuration had small and inconsistent effects. Opinion data of subjects indicated a strong preference for a battery nark belt concept.

Jan 1, 1980

By A. J. Barry

Recent developments in mechanizing longwall it mining in Europe have aroused considerable interest among American coal-mine operators because this method provides an opportunity to improve safety, production, efficiency, and recovery. The success of longwall mining in Europe has depended to a large degree on development of effective roof-control systems. One of the major contributing factors in designing these systems is development off improved supports, which combine high load-bearing capacities with controlled yield characteristics, to use in the face areas. Other factors that relate to successful longwall mining involve knowledge of the structural properties of the strata above end below the coal bed being mined, movements of these strata induced by mining, and effects of the strata movements on the strata itself, as well as on the support system used. Extensive studies of the above factors relating to long-wall mining have been made in coal-mining countries abroad, and corresponding studies (1, 2, 3, 4, 5)3/ of room-and-pillar operations have been made in this country. Although descriptions and results of experiments of mechanized longwall operations in the United States have been published (6, 7, 8), this is the first instrumented study of roof behavior on a longwall operation. In view of the possible widespread application of this method of mining to American coal mines, where underground mining conditions are different from those found in European mines, an investigation was conducted at a mechanized longwall operation inn the Lancashire No. 15 mine, Barnes & Tucker Co., Cambric County, Bakerton, Pa., to study the factors that affect roof control. This report describes this investigation and discusses the results. ACKNOWLEDGMENTS This investigation was made under a cooperative agreement between the Bureau of Mines and the Barnes & Tucker Co., Barnesboro, Pa., end was conducted in the Lancashire No. 15 mine located at Bakerton, Cambria County, Pa. The authors acknowledge the cooperation given by Richard Z. Todhunter, Sr., president, Richard T. Todhunter, Jr., general manager, and other mine officials and employees of the Barnes & Tucker Co. Mr. Edward Thomas, chief, Roof Control Section, Bureau of Mines, Washington, D. C., and Dr. Leonard Obert, chief, Applied Physics Branch. College Park, Md., collaborated in the planning and promulgation of the program investigation.

Jan 1, 1954

By W. W. Adams

Two important facts stand out as features of the metal- and nonmetal-mining4 industry of the United States in 1941 as compared with 1940: First, the number of employees and man-days of employment increased; second, accident-frequency rates, both fatal and nonfatal, decreased. Reports from mining companies to the Bureau of Mines covering underground, open-pit, and surface operations for 1941 re¬vealed the largest number of men employed since 1926 and the largest number of man-days worked since 1929. The combined fatal and non¬fatal accident-frequency rate for 1941, calculated on a basis of one mil¬lion man-hours of exposure to hazard, was (except for 1931 and 1932) the lowest since 1911, the earliest year for which figures are available. During this 31-year period, only 1938 and 1939 showed lower fatality rates, and only 1931 and 1932 had lower nonfatal-injury rates. Operating companies reported that 9,620 mines were active during all or some part of the year. These employed 125,290 men, an increase of more than 4 percent over 1940. The total volume of work performed at all mines, measured in terms of man-shifts, increased to nearly 32 million, a gain of 10 percent; man-hours of employment rose to almost 254 million, an increase of 10 percent over the 231 million man-hours worked in the previous year. The year's operations resulted in an average work-year of 255 days per man, an increase of 13 days per employee over the average working time in 1940. Although the 8-hour day prevails generally at most mines, the industry as a whole averaged 7.94 hours per shift, as in 1940.

Jan 1, 1944

By Seth C. Schaefer

The Bureau of Mines investigated the standard Gibbs energies of forma-tion AGfo, for NiCr204 (nickel chromite) and CoCr204 (cobalt chromite). High temperature galvanic cells employing stabilized ZrOz (zirconia) as the solid electrolyte were used to measure the open-circuit potentials for the cell reactions ?

Jan 1, 1986

By Charles A. Seitz

This Bureau of Mines report describes a chromatographic method for analyzing impurities in helium that utilizes a helium carrier gas contain-ing 25 to 30 ppm Ne. An example of the effect of trace amounts of nitrogen, methane, and moisture on the detector's response is shown. The added neon in the carrier does away with irregularities of the analysis which were experienced when the carrier contained up to 3 ppm Ne. The addition of 25 to 30 ppm Ne causes a loss of sensitivity, but the re-maining sensitivity is adequate for routine analyses. The high-neon carrier allows positive and more linear responses for eight impurities: neon, hydrogen, argon, oxygen, nitrogen, methane, carbon dioxide, and ethane. Neon concentration levels of 0.02 to 125 ppm in helium carrier gases were studied. The high-neon carrier has been in successful rou-tine use in Bureau of Mines helium facilities since October 1981.

Jan 1, 1985